Contents Before driving Introduction 2 Instrumentation 8 Controls and features 25 Seating and safety restraints 72 Starting and driving Starting 104 Driving 109 Roadside emergencies 145 Servicing Maintenance and care 172 Capacities and specifications 222 Customer assistance 234 Reporting safety defects 246 Index 247 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow.
Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
Introduction Using your vehicle with a snowplow For more information and guidelines for using your vehicle with a snowplow, refer to the Driving chapter. Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual, Ford Truck Body Builder’s Layout Book and the QVM guidelines as well as pertinent supplements.
Introduction If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Certification label. The label is located on the driver’s side door pillar or on the rear edge of the driver’s door. You can determine whether the ambulance manufacturer followed Ford’s recommendations by directly contacting that manufacturer. Ford Ambulance Preparation Package is only available on certain 7.3L Diesel engine equipped vehicles.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN 7
Instrumentation Instrument cluster (pg. 10) Speed control* (pg. 56) Turn signal and wiper/washer control (pg. 61) 40 FUEL FILL LOW FUEL F 30 50 60 80 100 E 20 40 H 18 C 8 P 10 0 80 000000 140 L - + 4 2 120 H 3 70 60 90 5 1 20 CRUISE ABS 160 MPH 0 0 0 0 km/h P RN D 21 100 0 SERVICE ENGINE SOON RPM X1000 LOW RANGE 6 BRAKE 4X4 ! PANEL DIM O RES ON SET ACCEL OFF COAST Headlamp control (pg. 25) Instrument panel dimmer switch (pg.
Instrumentation Electronic sound system (pg. 32) Gearshift lever* (pg. 114) VOL - PUSH ON AM FM1 BASS CLK ST TREB BAL FM FADE TAPE AMS SEEK SCAN VE RDRI SIDE REW EJ TUNE OVE 1 4X4 4X4 WD HIGH LOW 2 3 4 5 1-2 FF 6 PASSENGER AIR BAG OFF OFF ON OFF Climate control system (pg. 27) Passenger air bag deactivate switch (pg. 92) Auxiliary power point (pg. 27) 4WD selector* (pg.
Instrumentation WARNING LIGHTS AND CHIMES 40 FUEL FILL LOW FUEL F 30 50 60 80 100 E 20 40 - + 18 C 8 10 0 80 000000 140 L H 4 2 120 H 3 70 60 90 5 1 20 CRUISE ABS 160 MPH 0 0 0 0 km/h P RN D 21 100 0 SERVICE ENGINE SOON RPM X1000 LOW RANGE 6 BRAKE 4X4 ! DOOR AJAR Low fuel Illuminates as an early reminder of a low fuel condition indicated on the LOW fuel gauge (refer to Fuel Gauge in FUEL this chapter for more information).
Instrumentation What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened.
Instrumentation government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle. The Service Engine Soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing.
Instrumentation Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Transmission control indicator light (TCIL) Illuminates when the Transmission Control Switch (TCS), refer to OVERDRIVE Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF.
Instrumentation Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON ABS position. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released. Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on.
Instrumentation Four wheel drive indicator (if equipped) Momentarily illuminates when the 4x4 ignition is turned to the START position. Illuminates when 4x4 range is engaged. If the light continues to flash have the system serviced. Door ajar Illuminates when the ignition is in the ON or START position and any door is open.
Instrumentation The “SET” light comes on when either the COAST/SET or RES/ACCEL controls are pressed. The “SET” light turns off when the cruise cancel control is pressed or the brake is applied. Both the “CRUISE” and “SET” lights turn off when the OFF control is pressed or the ignition is turned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty, there is a small amount of reserve fuel in the tank.
Instrumentation Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Odometer Registers the total kilometers (miles) of the vehicle. 40 50 60 70 80 30 100 60 80 120 20 10 0 Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control.
Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer at the top of the scale or in the red zone may damage the engine. 3 4 2 5 1 0 6 RPM X1000 Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible.
Instrumentation TRIP COMPUTER (IF EQUIPPED) The trip computer tells you about the condition of your vehicle through a constant monitor of vehicle systems. You may select display features on the trip computer for a display of status. The appearance of your vehicle’s trip computer may differ depending on your vehicle’s option package, but the functions are the same. The trip computer only operates with the ignition in the ON position.
Instrumentation • variations in top-off procedure from one fill-up to another • rounding of the displayed values to the nearest liter (gallon) To reset the average fuel economy: 1. Press the MODE control repeatedly until average fuel economy is displayed (this is the only resettable display). 2. Press the E/M and MODE controls simultaneously. The display will illuminate the “AVG” indicator. MODE E/M While the indicator is lit, release both controls to reset the average fuel economy. Fuel range.
Instrumentation Outside air temperature The temperature can be displayed in Centigrade or Fahrenheit by pressing the E/M control. If the outside temperature falls below 3°C (38°F), the display will alternate from “ICE” to the outside temperature at a two second rate for one minute. MODE E/M Off. In this mode the display is off. Compass The compass display is contained in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW.
Instrumentation Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the trip computer on the overhead console. 3. Turn ignition to the ON position. 1 15 2 14 3 13 4 12 11 5 6 10 7 8 9 4. Press and hold both trip computer controls. After approximately four seconds, the trip MODE E/M computer will enter zone setting mode. Zone setting mode is indicated when the display lights the “ZONE” indicator. 5.
Instrumentation Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Locate the trip computer located in the overhead console. 2. Start the vehicle. 3. Press and hold both trip computer controls. After approximately eight seconds, the MODE E/M trip computer will enter CAL mode.
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. P Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Controls and features Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information.
Controls and features AUXILIARY POWER POINT The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. POWER POINT CLIMATE CONTROL SYSTEM Heater only system (if equipped) OFF Fan speed control Controls the volume of air circulated in the vehicle. Temperature control Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature.
Controls and features • OFF-Outside air is shut out and the fan will not operate. (Panel and floor) -Distributes outside air through the instrument • panel registers and the floor ducts. • (Floor) -Allows for maximum heating. Distributes outside air through the floor ducts. (Floor and defrost) -Distributes outside air through the floor • ducts and the windshield defroster ducts. (Defrost) -Distributes outside air through the windshield • defroster ducts.
Controls and features Manual heating and air conditioning system OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor will operate in all modes except (Panel) and (Floor).
Controls and features • • • • • • (Panel) -Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. OFF-Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts.
Controls and features • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate your air conditioner as you would normally. • Do not place objects over the defroster outlets.
Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo (with 2 speakers) VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 3 4 AM/FM AM/FM Stereo (with 4 speakers and fade capability) VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK AM / FM STEREO 1 32 2 3 4 AM/FM
Controls and features Volume/power control Press the control to turn the audio system on or off. VOL PUSH ON Turn the control to raise or lower volume. VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode. AM/FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Controls and features Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio mode. Seek function in radio mode • Press to find the next listenable station down the frequency band.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the TONE control once, then use the volume knob to adjust the desired level. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TONE control twice, then use the volume knob to adjust the desired level. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Controls and features Setting the clock Press CLK to toggle between listening frequencies and clock mode. To set the hour, press and hold the CLK control until CLOCK SET appears in the display and press the SEEK control: • • TONE CLK to decrease hours and to increase hours. To set the minute, press and hold the CLK control until CLOCK SET appears in the display and press the TUNE control: SEEK SEEK TUNE TUNE TONE CLK to decrease minutes and • SEEK SEEK to increase minutes.
Controls and features reverting back to the clock. In media mode, the media information will always be displayed. AM/FM stereo cassette VOL - PUSH ON AM FM1 BASS CLK ST TREB BAL FADE FM SEEK SCAN SIDE REW EJ TUNE 1 2 3 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and tape modes. AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. SEEK TUNE Scan function The scan function works in radio mode. SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features Tape select • To enter tape mode while in radio mode, press the TAPE AMS control. CLK TAPE AMS Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection CLK being played or to skip to the next selection. TAPE To activate the feature, momentarily AMS depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Controls and features DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt noise 4 reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolbyt noise reduction. Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing Corporation. “Dolbyt” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Controls and features • • to decrease minutes and to increase minutes. SEEK SEEK TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.
Controls and features Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. Turn control to raise or lower volume. VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Controls and features Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. to move to the next • Press frequency up the band (whether or not a listenable station is located there). Hold for quick movement.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. SEEK SEEK TUNE TUNE Seek function in tape mode • Press to listen to the previous selection on the tape. to listen to the next selection on the tape. • Press Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc.
Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again. Scan function in CD or CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the CD.
Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing. CLK If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Controls and features Press the TREB control then press: to decrease the treble output • and • to increase the treble output. SEL Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and to shift sound to the right. • Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features Tape/CD select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • To begin CD play (if CD(s) are loaded), press the CD control. TAPE CD The first track of the disc will begin playing. If returning from radio or tape mode, CD play will begin where it stopped last.
Controls and features Eject function Press the EJ control to stop and eject a tape. EJ Press the EJ control to stop and eject a CD. EJ DolbyT noise reduction Dolbyt noise reduction operates in tape mode. Dolbyt noise reduction 4 reduces the amount of hiss and static during tape playback. control to activate (and deactivate) the Dolbyt noise Press the reduction. Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing Corporation.
Controls and features Setting the clock To set the hour, press and hold the CLK control and press SEEK: AUTO CLK • • to decrease hours and to increase hours. SEEK SEEK TUNE TUNE To set the minute, press and hold the CLK control and press TUNE: AUTO CLK to decrease minutes and • to increase minutes. • If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner.
Controls and features The CLK button will allow you to switch between media display mode AUTO (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 CLK seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.), the media information will again display for 10 seconds before reverting back to the clock.
Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into each slot of the CD changer magazine.
Controls and features Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/ volume relative to other stations. • Terrain.
Controls and features TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on.
Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. ON OFF Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RES SET ACCEL COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Controls and features To set a higher set speed • Press and hold SET/SET ACC/ SET ACCEL. Release the control when the desired vehicle speed is RES reached or • Press and release SET/SET ACC/ SET ACCEL SET ACCEL. Each press will increase the set speed by 1.6 COAST km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET/SET ACC/SET ACCEL. You can accelerate with the accelerator pedal at any time during speed control usage.
Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). RES SET ACCEL COAST TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Controls and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer.
Controls and features The TCIL (the word OFF) will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode. For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter. POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows.
Controls and features One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. AUTO Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls WINDOW LOCK except for the driver’s press the left side of the control. Press the right side to restore the window controls.
Controls and features CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.
Controls and features 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Controls and features ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, slide the mirror cover open. To turn off the visor mirror lamps, slide the mirror cover closed. CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features.
Controls and features REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate.
Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm.
Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prio
Controls and features Reprogramming transmitters To reprogram all transmitters, place the key in the ignition and turn from OFF to ON eight times in a row (within 10 seconds). After doors lock/unlock, press any control on all transmitters (up to four). When completed, turn the ignition to OFF. All transmitters must be reprogrammed at the same time. TAILGATE LOCK (IF EQUIPPED) Your vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate.
Seating and safety restraints SEATING Full bench seat (if equipped) • Lift the track release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the release lever located at the bottom of the seatback to quickly fold the seatback forward. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place. • Pull the seatback handle up to recline the seat.
Seating and safety restraints Captain’s chair (if equipped) • Lift the track release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the seatback handle up to recline the seat. • Push down the release lever located at the bottom of the seatback to quickly fold the seatback forward. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and safety restraints Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.
Seating and safety restraints Folding up the rear seats (if equipped — SuperCab only) The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position. 1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position. Returning the seat to seating position Always be sure that the seat is in a latched position, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Seating and safety restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible.
Seating and safety restraints • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and safety restraints Safety belt replacement label (Crew Cab Only) The short plastic boot on the front safety belt at the passenger outboard anchor location covers a “Replace Belt” label on the safety belt. In the event of a collision, the colored label (REPLACE BELT) may become visible. If this occurs, the safety belt must be replaced. Whenever the yellow portion of the label is visible, the safety belt must be replaced.
Seating and safety restraints Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury. Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Seating and safety restraints • 4–door Super Cab To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder.
Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates1-2 minutes and the warning chime sounds 4-8 seconds. The safety belt warning light and warning chime turn off. The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... 9Crashes are rare events9 Consider... 36 700 crashes occur every day. The more we drive, the more we are exposed to 9rare9 events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 9I’m not going far9 3 of 4 fatal crashes occur within 25 miles of home.
Seating and safety restraints One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Seating and safety restraints 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three seconds. 8.
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 40 F H 50 60 60 70 80 30 3 VOL - PUSH ON 80 AM FM 1 40 140 20 10 0 2 100 120 20 H 18 90 FM1 BASS ST TREB BAL FADE AUTO SET DIESEL FUEL ONLY 4 160 MPH km/h 100 SEEK RPM x 1000 SCAN TUNE EJ DOLBY B NR TAPE CD DISCS REW FF 1 SIDE 1-2 2 3 COMP 4 SHUFFLE 5 6 P OFF O A/C RES MAX A/C ON SET ACCEL OFF COAST Your vehicle is equipped with a crash sensing and diagnostic module which records in
Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts.
Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and safety restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. Passenger air bag ON/OFF switch (if equipped) An air bag ON/OFF switch has been installed in this vehicle.
Seating and safety restraints In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turn the switch to ON. PASSENGER AIR BAG 2. The OFF light will briefly OFF illuminate when the ignition is ON turned to On. This indicates that the OFF passenger air bag is operational.
Seating and safety restraints Always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly. If a child in a rear facing infant seat must be transported in front, the passenger air bag must be turned OFF. This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury to the infant when the air bag inflates is substantial.
Seating and safety restraints • although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of the vehicle; or • the child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition. 3. Medical condition.
Seating and safety restraints 2.
Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle.
Seating and safety restraints A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion. You may wish to discuss the special needs of your child with your pediatrician.
Seating and safety restraints • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap.
Seating and safety restraints An air bag can kill or injure a child in a child seat. Child seats should never be placed in the front seats, unless passenger air bag switch is turned off, See Passenger air bag deactivation switch. Rear facing child seats should NEVER be placed in the front seats unless the passenger airbag switch is turned off. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3.
Seating and safety restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract.
Seating and safety restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine.
Seating and safety restraints Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • If • • Make sure the gearshift is in P (Park). starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Starting 40 FUEL FILL LOW FUEL F 30 50 60 80 100 60 E 20 40 H 18 C 8 10 0 80 000000 140 L - + 4 2 120 H 3 70 90 5 1 20 ABS 160 MPH 0 0 0 0 km/h P RN D 100 0 SERVICE ENGINE SOON 21 CRUISE RPM X1000 LOW RANGE 6 BRAKE 4X4 ! DOOR AJAR Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. light may not illuminate. • If the driver’s safety belt is fastened, the STARTING THE ENGINE 1.
Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Starting Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving released. (If your brake warning lamp illuminates, have your vehicle serviced immediately.) Using RABS • In an emergency, applying full pressure may cause the front wheels to lock. If the front brakes lock, the vehicle cannot be steered. You should apply the brakes with steadily increasing force, as if “squeezing” the brakes. If you feel the front wheels begin to lock, momentarily release the pedal and repeat the “squeeze” technique.
Driving With the ABS light on, the anti-lock brake system is disabled and normal BRAKE braking is still effective unless the ! brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately.) Using ABS • In an emergency or when maximum efficiency from the ABS is required, apply continuous force on the brake.
Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
Driving Extended use of other than the manufacturer’s specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver. To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Driving AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1. Apply the parking brake, turn ignition to the LOCK position, then remove the key. 2.
Driving Driving with a 4–speed automatic transmission Understanding gearshift positions To put your vehicle in gear, start the engine, depress the brake pedal, then move gearshift lever out of P (Park). Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park).
Driving (Overdrive) can be deactivated by pressing the transmission control switch (TCS) on the end of the gearshift lever. The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate. OVERDRIVE OFF OVERDRIVE Drive – Not shown on the display. Activate by pressing the transmission control switch (TCS) on the end of the gearshift lever with the gearshift position. The TCIL (the word OFF) will illuminate on the in the gearshift lever.
Driving higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Forced Downshifts To gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor. The transmission will downshift to the appropriate gear: third, second or first gear.
Driving When starting a vehicle with a manual transmission, you must: 1. Make sure the parking brake is fully set. R 1 3 D 1 3 D 2. Depress the clutch pedal fully. 2 4 R L 2 4 3. Put the gearshift lever in N (Neutral). 4. Turn the ignition to position 5 (START) to start the engine, let the engine idle for a few seconds. 5. Depress the brake pedal. 6. Release the parking brake. 7. Move the gearshift lever to the desired gear. 8. Release the brake pedal. 9.
Driving Recommended shift speeds Downshift according to the following charts for your specific engine/drivetrain combination: 1 2 1 2 Maximum downshift speeds 1 5-speed transmission Shift from: Transfer case position (if equipped)2 2H or 4H 4L D (Overdrive) - 4 72 km/h (45 mph) 35 km/h (22 mph) 4-3 56 km/h (35 mph) 23 km/h (14 mph) 3-2 32 km/h (20 mph) 13 km/h (8 mph) 2-1 8 km/h (5 mph) 0 km/h (0 mph) Use 2H or 4H for 4WD equipped vehicles. Downshift at lower speeds when driving on slippery surfaces.
Driving Parking your vehicle 1. Disengage the clutch, apply brake and shift into N (Neutral). 1 3 D R 1 3 D 2 4 R L 2 4 2. Set parking brake. 3. Shift into 1 (First). 4. Turn the ignition key to position 3 (OFF).
Driving Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. Put the gearshift lever in N (Neutral) and wait at least three seconds before shifting into R 1 3 D (Reverse).
Driving Removing key from ignition • Turn the ignition key to position 2. • Push the release lever forward and rotate the key towards you and remove. POWER TAKE OFF (PTO) CAPABILITY (IF EQUIPPED) Some vehicles equipped with an automatic transmission and the 6.8L or 7.3L engine are also equipped with Power Take Off (PTO) capability. These vehicles have a special transmission case, internal components and calibration for PTO usage. If your vehicle is equipped with a 7.3L Diesel engine, refer to the 7.
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired.
Driving • automatic hub locks can be manually overridden by rotating the hub lock control from AUTO to LOCK. Automatic operation of the hub locks is recommended. • For proper operation, make sure that the arrow and the indicator dot on the hub are aligned. Manual 4x4 system (if equipped) The 4WD system is engaged or disengaged by rotating the control for both front wheel hub locks from the FREE or LOCK position, then manually engaging or disengaging the transfer case with the floor-mounted shifter.
Driving • LOW RANGE –momentarily illuminates when the ignition is turned to the ON position. Illuminates when 4L (4x4 Low) is engaged. LOW RANGE Using a manual 4WD system (if equipped) 2H (2WD High) – Power to rear axle only. 4H (4WD High) – Power to front and rear axles. N (Neutral) – No power to either axle. 4L (4WD Low) – Power to front and rear axles at reduced speed.
Driving Shifting from 4H (4WD high) to 2H (2WD high) Move the transfer case lever to 2H 2H (2WD High) at a stop or any forward speed up to 88 km/h (55 4H mph). N With the vehicle at complete stop, disengage the locking hubs 4L (optional) by rotating the hub lock control from LOCK to FREE. • For proper operation, make sure that the arrow and the indicator dot on the hub are aligned. Shifting from 4H (4WD high) to 4L (4WD low) 1. Bring the vehicle to a complete stop. 2. Depress the brake. 3.
Driving 4. Move the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 2H (2WD high) and hold the shift lever in position until the transfer case has fully engaged (up to 15 seconds). 5. If the transfer case does not engage, repeat steps 1 through 4. 2H 4H N 4L Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards.
Driving Shifting from 2WD (2WD high) to 4x4 HIGH (4WD high) Rotate the 4WD control to the 4x4 HIGH position at speeds up to 88 4X4 4X4 HIGH km/h (55 mph). LOW 2WD • To prevent damage, the electronic shift 4WD system is designed to engage 4x4 HIGH (4WD high) when the vehicle is moving. If the 4x4 indicator light does not illuminate when shifting a vehicle that is stationary, start the vehicle moving. Once the vehicle is moving, 4x4 HIGH (4WD high) will engage and the 4x4 indicator will illuminate.
Driving 4. Move the 4WD control to the 4x4 LOW position. 5. Hold the shift command until the LOW RANGE indicator light illuminates. 6. If the LOW RANGE indicator light does not illuminate after 15 seconds, start the vehicle moving, then repeat steps 1 through 5 before reporting any shift concerns to your dealer. 2WD 4X4 HIGH 4X4 LOW Shifting from 4x4 LOW (4WD low) to 4x4 HIGH (4WD high) or 2WD (2WD high) 1. Bring the vehicle to a complete stop. 2. Depress the brake. 3.
Driving Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps. You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’s portfolio. If your vehicle gets stuck If the vehicle is stuck it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern.
Driving If the transmission, transfer case or front axle are submerged in water, their fluids should be checked and changed, if necessary. Water intrusion into the transmission may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant should be replaced. Driving on hilly or sloping terrain When driving on a hill, avoid driving crosswise or turning on steep slopes. You could lose traction and slip sideways. Drive straight up, straight down or avoid the hill completely.
Driving If your vehicle is equipped with a Four Wheel Anti-lock Brake System (ABS), apply the brakes as you normally would. In order to allow the ABS to operate properly, keep steady pressure on the brake pedal. When driving on snow or ice with either braking system, allow more stopping distance and drive slower than usual. Consider using one of the lower gears.
Driving • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight.
Driving Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this owner guide. Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
Driving Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. TOWING A TRAILER Your vehicle may tow a Conventional/Class IV trailer or fifth wheel trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts. 2nd unit bodies are not included in maximum trailer weight ratings.
Driving Trailer towing tables Engine 5.4L 5.4L 6.8L 6.8L F-250 with manual transmission Rear axle Maximum Maximum trailer ratio GCWR-kg (lbs.) weight-kg (lbs.) 1 3.73 6 124 (13 500) 4 536 (10 000) 4.10 6 804 (15 000) 4 536 (10 000) 3.73 7 484 (16 500) 4 536 (10 000) 4.30 8 165 (18 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by subtracting GVW from GCWR. Engine 5.4L 5.4L 6.8L 6.
Driving Engine 5.4L 5.4L 6.8L 6.8L F-350 with automatic transmission Rear axle Maximum Maximum trailer ratio GCWR-kg (lbs.) weight-kg (lbs.) 1 3.73 6 124 (13 500) 4 536 (10 000) 4.10 6 804 (15 000) 4 536 (10 000) 3.73 7 711 (17 000) 4 536 (10 000) 4.30 9 072 (20 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by subtracting GVW from GCWR. Engine 6.8L 6.
Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to the axle. You must distribute the load in your trailer so that 10% of the total weight of the trailer is on the tongue.
Driving Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
Driving Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information. Trailer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Driving All Rear Wheel Drive (RWD) vehicles This applies to all cars and 4x2 trucks/sport utilities with rear wheel drive capability. An example of recreational towing is towing your vehicle behind a Motorhome. The following recreational towing guidelines are designed to ensure that your transmission is not damaged. • Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles).
Driving • The Front Axle Accessory Reserve Capacity and the Total Accessory Reserve Capacity listed on the bottom right of the Safety Compliance Certification Label will determine whether or not the addition of a snowplow will overload your vehicle. • The weight of the snowplow and supporting components distributed to the front axle must not exceed the front accessory reserve capacity. • The total weight of the snowplow and aftermarket equipment must not exceed the Total Accessory Reserve Capacity.
Driving Snowplowing with your air bag equipped vehicle Your vehicle is equipped with driver and passenger (if equipped) air bag Supplemental Restraint System (SRS). The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. Careless or high speed driving while plowing snow which results in sufficient vehicle decelerations can deploy the air bag. Such driving also increases the risk of accidents.
Driving If you are driving more than 24 km (15 miles) at temperatures above freezing, angle the plow blade either full left or full right to provide maximum airflow to the radiator. If you are driving less than 24 km (15 miles) at speeds up to 64 km/h (40 mph) in cold weather, you will not need to worry about blade position to provide maximum airflow. 4WD operation while plowing • Shift transfer case to 4x4 LOW (4WD Low) when plowing in small areas at speeds below 8 km/h (5 mph).
Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–894–2582).
Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses 2A 3A 4A 5A 7.
Roadside emergencies To remove the fuse panel cover, turn the panel fasteners counterclockwise. 31 20 21 11 RELAY 5 9 10 30 29 19 8 RELAY 4 28 18 7 27 17 6 26 16 25 15 4 5 RELAY 3 24 14 23 13 2 3 (NOT USED) 12 RELAY 1 FUSE1 22 To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside emergencies The fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 19 20 21 22 23 24 25 26 27 28 29 30 31 Relay Relay Relay Relay Relay 1 2 3 4 5 Fuse Amp Passenger Compartment Rating Fuse Panel Description 10A Auxiliary Powertrain Control Module (APCM) (Diesel only), Instrument Cluster, GEM Module, Overdrive Cancel Switch, Idle Validation Switch (Diesel only), Overhead Console, Diesel PCM via Clutch 15A Starter Motor Relay Coil, Clutch Switch — Not Used 10A Air Bag Module, Passenger Air Bag Activation/Deactivation Switch, Blo
Roadside emergencies Power distribution box The power distribution box, trailer tow and electronic shift on the fly relay blocks are located in the engine compartment near the brake master cylinder. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies The high-current fuses and relays are coded as follows. Fuse/Relay Location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Fuse Amp Rating 7.5A * 10A* 7.
Roadside emergencies Fuse/Relay Location 21 22 23 24 25 26 Fuse Amp Rating 50A** 50A** 40A** 30A** (Gasoline only) 20A** (Diesel only) 30A*** 20A** Power Distribution Box Description Ignition Switch (B1 & B3) Junction Box Battery Feed Blower Motor PCM Power Power Windows If equipped with Remote Keyless Entry-Driver Door Unlock Relay Coil, All Door Unlock Relay Coil, All Door Lock Relay Coil, Park Lamp Flash Relay, If not equipped with Remote Keyless Entry-Power Door Lock Motors 27 - (Gasoline only) Gaso
Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Your vehicle may be equipped with a spare tire that can be used as either a spare or a regular tire. The spare tire is not equipped with wheel trim. The wheel trim from the original wheel/tire may be used on the spare.
Roadside emergencies • one wheel nut wrench. Slide over square end of jack handle. 2. The following steps are required to move the support bracket (if equipped) away from the spare tire: • With tapered end of lug wrench, loosen the eyebolt on the support bracket. • Line up the eyebolt with the slot in the support bracket. • Slide the support bracket off the eyebolt and move the support bracket away from the spare tire. 3.
Roadside emergencies 4. Insert the hooked end of the jack handle into the rear bumper drive tube. The handle will stop moving and you will feel forward resistance to turning when properly engaged. 5. Turn the handle counterclockwise and lower the spare until you can slide the tire rearward and the cable is slack. 6. Remove the retainer through the center of the wheel. Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2.
Roadside emergencies Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake. • Automatic transmission: Place gearshift lever in P (Park). • Manual transmission: Place gearshift lever in R (Reverse). • Electronic Shift On the Fly four wheel drive: Place transfer case in 2WD, 4x4 HIGH or 4x4 LOW. • Manual shift transfer case four wheel drive: Place transfer case in 2H, 4H or 4L.
Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or R (Reverse) (manual transmission).
Roadside emergencies • Front (4x2) • Front passenger side (4x4) 160
Roadside emergencies • Front driver side (4x4) Make sure the jack fits into the notched area on the differential housing.
Roadside emergencies 8. Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 9. Remove the lug nuts with the lug wrench. 10. On single rear wheel vehicles, replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front tires and vehicles equipped with single rear wheels. If replacing an inboard rear tire on a dual rear wheel vehicle, the valve stem must be facing outward.
Roadside emergencies • Front (4x2) • Front driver side (4x4) 163
Roadside emergencies • Front passenger side (4x4) • Rear 164
Roadside emergencies 14. Insert the jack handle into the pump linkage. 15. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’s rated capacity. 16. Remove the lug nuts with the lug wrench. 17. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels.
Roadside emergencies On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 800 km (500 miles) of operation after any wheel change or any time the lug nuts are loosened. Bolt Size Wheel Lug nut Torque* Nm Lb-ft 1/2-20 135 100 9/16-18 190 140 * Torque specifications are for nut and bolt threads free of dirt and rust. Do not use oil or grease on threads. Use only Ford recommended replacement fasteners.
Roadside emergencies 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. + + – – 2.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift or a slingbelt with T-hooks. On 4x4 vehicles, it is recommended that your vehicle be towed with a wheel lift or flatbed equipment with all the wheels off the ground.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Maintenance and care 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. • Manual transmission: 1.
Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. HOOD 2. Go to the front of the vehicle and release the auxiliary latch located under the right center of the hood. Slide the handle to release the auxiliary latch. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8/6.8L V10 gasoline engines Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 9 8 10 11 1 2 7 3 4 5 6 1. Engine oil dipstick 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid reservoir 4. Power distribution box 5. Power steering fluid reservoir 6. Air filter assembly 7. Engine coolant reservoir 8.
Maintenance and care ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and care • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and care Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API certification trademark will meet all requirements for your vehicle’s engine. Ford oil specification is WSS-M2C153-G. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Maintenance and care BRAKE FLUID Checking and adding brake fluid—gasoline engine Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until MAX the level reaches MAX. Do not fill above this line. 4.
Maintenance and care Checking and adding brake fluid—diesel engine Check and refill the Hydromax brake fluid reservoir using the following procedure. Refer to the Scheduled Maintenance Guide for the service interval. 1. Clean the reservoir caps before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until the level reaches MAX. Do not fill above this line. 4.
Maintenance and care CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Capacities and specifications. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical if irritation persists. If taken internally, drink water and induce vomiting. Seek medical attention immediately.
Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter.
Maintenance and care • protection against rust and other forms of corrosion. • an accurate temperature readout from the engine coolant gauge. The engine coolant must be maintained at the correct fluid level and concentration to work properly. If the engine coolant fluid level and concentration is not maintained correctly, damage to the engine and cooling system may result. When the engine is cold, check the level of the engine coolant in the reservoir.
Maintenance and care Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44-A. • DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). • DO NOT USE a DEX-COOLt engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44-D. • DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Maintenance and care mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the “cold fill level” or within the “cold fill range” as listed on the reservoir (depending upon application). Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month.
Maintenance and care Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • it may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance and care How fail-safe cooling works If the engine begins to overheat: • the engine coolant temperature H gauge will move to the red (hot) area. • the and symbol will illuminate. C • the Service Engine Soon indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate.
Maintenance and care 5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. FULL COLD CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary, use only MERCONt ATF.
Maintenance and care 5. Recheck the fluid level on the dipstick. Do not add fluid if the level is between the arrows in the FULL COLD range. 6. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the FULL COLD range. Be sure to put the dipstick back in the reservoir. TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid.
Maintenance and care Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F). ADD COLD HOT DO NOT ADD DON'T ADD IF IN CROSSHATCHED AREA • CHECK WHEN HOT IDLING IN PARK Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving.
Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct.
Maintenance and care 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3.
Maintenance and care Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft Part Numbers in the Capacities and specifications chapter.
Maintenance and care 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the open end of the air filter housing. 4. Install a new air filter element, ensuring the arrow on the top half of the air filter housing lines up with the notch on the bottom half of air filter housing. Be careful not to crimp the filter element edges between the air filter housing. This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 5.
Maintenance and care However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells. If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content).
Maintenance and care RN LE TU AD RE Because your vehicle’s engine is also electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2.
Maintenance and care Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm.
Maintenance and care diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
Maintenance and care The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Maintenance and care • Four tire rotation • Five tire rotation 200
Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.
Maintenance and care The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used as chains may chip aluminum wheels. Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains.
Maintenance and care Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
Maintenance and care When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Maintenance and care with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced.
Maintenance and care Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops.
Maintenance and care ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000 miles) of driving (engine break-in period).
Maintenance and care Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5.
Maintenance and care • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving.
Maintenance and care • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker.
Maintenance and care Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly. Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
Maintenance and care BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • High-mount brakelamp • Brakelamps • Turn signals • License plate lamp • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs (aerodynamic) 1.
Maintenance and care 6. Insert the glass end of the new bulb into the headlamp assembly. When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 7. Install bulb retaining ring over the plastic base and lock the ring into the socket by turning it clockwise until you feel a “stop.” 8. Connect the electrical connector into the rear of the plastic base until it “snaps.
Maintenance and care 6. Remove the four screws and the headlamp retaining ring from headlamp. 7. Disconnect the electrical connector and remove headlamp. To install the new headlamp, reverse the removal procedure. Replacing tail lamp/turn/backup lamp bulbs — F250/F350 only The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2.
Maintenance and care Replacing brake/tail/backup lamp bulbs — F450/F550 only The brake/tail/backup lamp bulbs are located in the same portion of the tail lamp assembly. Follow the same steps to replace either bulb: 1. Remove the four screws and the lamp lens from lamp assembly. 2. Carefully pull the bulb straight out of the socket and push in the new bulb. 3. Install the lens on the lamp assembly with the four screws. Replacing cargo lamp and high-mount brakelamp bulbs To remove the lamp assembly: 1.
Maintenance and care Replacing roof marker bulbs To change the cab marker bulbs: 1. Remove the screw and lens from the lamp assembly. 2. Carefully pull the bulb straight out of the socket and push in the new bulb. 3. Install lens on lamp assembly with screw. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2.
Maintenance and care Function Number of Trade number bulbs Headlamps (aerodynamic) 2 9007 Headlamps (sealed beam) 2 H6054 Park/turn 2 3157 Sidemarker 2 194 Tail/stop/turn/sidemarker 2 3157 K Backup 2 3156K High-mount stoplamp 1 921 License plate lamp 2 168 Cargo lamp 2 906 Roofmarker 5 194 (a) Rear fender clearance 4 Exteroir visor lamp (if equipped) 4 194 Rear identification 3 194 All replacement bulbs are clear in color except where noted.
Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis.
Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products.
Maintenance and care Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent.
Maintenance and care Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing.
Capacities and specifications MOTORCRAFT PART NUMBERS Component* Air filter element Fuel filter Oil filter PCV valve Battery (Standard) Battery (Optional) Spark plugs-platinum** 5.4L V8 engine FA-1634 FG-986B FL-820-S EV-233 BXT-65-650 BXT-65-750 AWSF-22E 6.8L V10 engine FA-1634 FG-986B FL-820-S EV-233 BXT-65-650 BXT-65-750 AWSF-22E *Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for Motorcraft diesel engine service part numbers.
Capacities and specifications Fluid Engine coolant Engine oil (includes filter change)-Gas engines Engine oil (includes filter change)-Diesel engine Fuel tank Power steering fluid 3 Ford Part Application Name Premium Engine 5.4L V8 engine Coolant without A/C 5.4L V8 engine with A/C 6.8L V10 engine Capacity 16.9L (17.9 quarts) 18.4L (19.4 quarts) 29.0L (30.6 quarts) 5.7L (6.0 quarts) Motorcraft SAE All 5W-30 Super Premium Motor Oil Refer to your 7.
Capacities and specifications Fluid Transfer case fluid Transmission fluid 4 Ford Part Name Motorcraft MERCONt ATF Synthetic MERCONt ATF Motorcraft MERCONt ATF Application 4x4 vehicles 5-speed manual 6-speed manual Automatic Windshield washer fluid Ultra-Clear Windshield Washer Concentrate All Capacity 1.9L (2.0 quarts) 3.2L (3.4 quarts) 5 5.5L (5.8 quarts) 5 16.7L (17.7 quarts) 6 4.0L (4.
Capacities and specifications fluid that indicates dual usage (MERCONt and MERCONt V) in an automatic transmission application requiring MERCONt may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage. 5 Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 6 Indicates only approximate dry-fill capacity.
Capacities and specifications Ford part name or equivalent Motorcraft SAE 5W-30 Super Engine oil Premium Motor Oil Hinges, Multi-Purpose latches, striker Grease plates, fuel filler door hinge and seat tracks Transmission/ Premium steering/ Long-Life Grease parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Power Motorcraft steering fluid MERCONt ATF and transfer case fluid (if equipped) Manual Synthetic transmission MERCONt ATF 2 (5-speed) Manual Motorcraft transmission MERCONt AT
Capacities and specifications submerged in water. Dana rear axles also contain a synthetic lubricant but do require a change. Refer to your “Service Guide” for change intervals on Dana rear axles. 2 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. Check the container to verify the fluid being added is of the correct type. Refer to your Scheduled Maintenance Guide to determine the correct service interval.
Capacities and specifications VEHICLE DIMENSIONS F250–except Crew Cab Dimension (3) Overall width (4) Wheelbase Regular Cab 4x2 1 864 mm (74 in) 1 736.3 mm (68.3 in) / 1 729.3 mm (68 in) 2 031 mm (79.9 in) 3 479.8 mm (137 in) (5) Overall length 5 646 mm (222.2 in) (1) Overall height (2) Track (Front / Rear) a b Short wheel base Body style Regular Super Cab Cab 4x4 4x2 1 958 mm 1 870 mm (77.1 in) (73.6 in) 1 736.3 mm 1 736.3 mm (68.3 in) / (68.3 in) / 1 729.3 mm 1 729.
Capacities and specifications F350–except Crew Cab Dimension Chassis Cab 1 972 mm (77.6 in) Body Regular Cab 1 860 mm (73.2 in)c,e (2) Track (Front / Rear) 1 736.3 mm (68.3 in) / 1 879.6 mm (74.0 in) 1 736.3 mm (68.3 in) / 1 729.3 mm (68.0 in) (3) Overall width (4) Wheelbase 2 025 mm (79.7 in) 3 576.3 mm (140.8 in) 2 031 mm (79.9 in) 3 479.8 mm (137.0 in) (5) Overall length 5 732 mm (225.7 in) 5 754 mm (226.5 in) (1) Overall height style Super Cab 4x2 1 865 mm (73.4 in)a 1 861 mm (73.
Capacities and specifications F350-Crew Cab Dimension (1) Overall height (2) Track (Front / Rear) (3) Overall width (4) Wheelbase (5) Overall length a b 1 1 1 1 3 4 6 6 Body Crew Cab 4x2 929 mm (75.9 in) 745 mm (68.7 in)/ 729 mm (68.1 in)a,b 988 mm (78.3 in)a,b 967 mm (156.2 in )a / 379 mm (172.4 in)b 242 mm (245.8 in)a / 654 mm (262.0 in)b style Crew Cab 4x4 2 038 mm (80.2 in) 1 736 mm (68.4 in)/ 1 729 mm (68.1 in)a,b 2 077 mm (79.0 in)a,b 3 967 mm (156.2 in )a / 4 379 mm (172.4 in)b 6 242 mm (245.
Capacities and specifications F550 Dimension Chassis Cab 4x2 (1) Overall 2 076 mm height (81.7 in) (2) Track 1 736 mm (Front / (68.3 in) / Rear) 1 879 mm (74 in) (3) Overall 2 025 mm width (79.7 in) (4) 3 576 mm Wheelbase (140.8 in) (5) Overall 5 732 mm length (225.6 in)a 6 341 mm (249.6 in)b a Short wheel base b Long wheel base Body Chassis Cab 4x4 2 075 mm (81.6 in) 1 736 mm (68.3 in) / 1 879 mm (74 in) 2 376 mm (93.5 in) 3 576 mm (140.8 in) 5 733 mm (225.7 in)a 6 343 mm (249.
Capacities and specifications 4 5 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. MFD. BY FORD MOTOR CO. IN U.S.A.
Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) XXXXXXXXXXXXXXXXX Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada).
Customer assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern cannot be resolved at the dealership level, please contact the Ford Customer Assistance Center.
Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O.
Customer assistance dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states.
Customer assistance Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the unique brochures for California, West Virginia, Georgia and Wisconsin purchasers/lessees.
Customer assistance • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application.
Customer assistance You may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O.
Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S.
Customer assistance Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Tri
Customer assistance Comfort and convenience Air conditioner Bed web net Cargo nets Cargo organizers Cargo storage bin Cargo trays Engine block heaters Power sliding rear window Tire step Travel equipment Auto headlamp system with Daytime Running Lights (DRL) Bumper mounted bike courier Daytime running lights (DRL) Electrochromic inside mirror with compass Electrochromic inside mirror with compass and temperature display Fog lights Framed luggage covers Heavy-duty battery Off road lights Pickup box rails Run
Customer assistance Protection and appearance equipment Air bag anti-theft locks Bed mat/bedliner tailgate covers Bed mats Bedliners Carpet floor mats Cleaners, waxes and polishes Diamond plate bed rail caps Diamond plate front box protection Diamond plate splash guards Diamond plate tool box Flat splash guards Front end covers (full) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars/Combo bars Side window air deflectors Spare tire lock Step bumpers
Customer assistance the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label). Consult your dealer for specific weight information. • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Accessory delay ..........................63 Air bag supplemental restraint system ..........................88 and child safety seats ..............89 description ................................88 disposal ......................................92 driver air bag ............................90 indicator light ......................13,91 operation ...................................90 passenger air bag .....................90 passenger deactivation switch ...................92 Air cleaner filter ......
Index calibration .................................24 set zone adjustment .................23 Console ........................................66 Controls power seat .................................73 Coolant checking and adding ..............182 refill capacities .................185,222 specifications ...................225,227 Cruise control (see Speed control) ....................56 Customer Assistance ................145 Ford accessories for your vehicle .....................................
Index capacity ...................................222 choosing the right fuel ...........204 comparisons with EPA fuel economy estimates .................210 detergent in fuel .....................205 filling your vehicle with fuel .......202,206,207 filter, specifications .........206,222 fuel pump shut-off switch .....146 gauge .........................................17 improving fuel economy ........207 low fuel warning light ..............10 octane rating .............204,227,228 quality ..............
Index replacing bulbs ............212,213,214,215,216 Lane change indicator (see Turn signal) ........................56 Lights, warning and indicator ....10 air bag ........................................13 anti-lock brakes (ABS) .....14,110 brake ..........................................13 charging system ........................14 check coolant ............................15 cruise indicator .........................15 door ajar ....................................15 engine oil pressure ...............
Index Snowplowing ............4,141,142,143 Spark plugs, specifications ...............222,227,228 Special notice .............................3,5 ambulance conversions ..............4 diesel-powered vehicles .............3 four-wheel drive vehicles ...................143,144 utility-type vehicles ....................3 Specification chart, lubricants ............................225,227 Speed control ..............................56 Speedometer ...............................17 Starting your vehicle ........
Filling station information Item Required fuel Fuel tank capacity Engine oil (includes filter change) Tire size and pressure Hood release Coolant capacity Power steering fluid capacity Manual transmission (5-speed) 2 Manual transmission (6-speed) 2 Automatic transmission fluid capacity 2 Information Unleaded fuel only - 87 octane Refer to Refill capacities in the Capacities and specifications chapter. 5.7L (6.0 quarts). Use Motorcraft SAE 5W-30 Super Premium Motor Oil, Ford specification WSS-M2C153-G.
Filling station information fluid. However, these dual usage fluids may be used in transmissions that require the MERCONt V type fluid. MERCONt and MERCONt V type fluids are not interchangeable. DO NOT mix MERCONt and MERCONt V. Use of a transmission fluid that indicates dual usage (MERCONt and MERCONt V) in an automatic transmission application requiring MERCONt may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage.