Contents Before driving Introduction 2 Instrumentation 8 Controls and features 20 Seating and safety restraints 89 Starting and driving Starting 123 Driving 128 Roadside emergencies 158 Servicing Maintenance and care 184 Capacities and specifications 240 Customer assistance 249 Reporting safety defects 262 Index 263 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
Introduction SPECIAL NOTICES Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident.
Introduction Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. Electric vehicles For information on operating your Electric Vehicle, also refer to the Electric Vehicle Owner’s Guide Supplement.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap 7
Instrumentation Instrument panel dimmer control (pg. 21) Instrument cluster (pg. 10) Headlamp control (pg. 20) DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 6 30 20 1 CHECK FUEL CAP F ABS 10 0 ! E 60 70 80 0 0 0 80 100 P 40 90 120 60 2 C 50 40 RPMx1000 140 000000 20 MPH R N D 2 1 160 100 180 110 km/h 120 H SPEED CONT L 4WD HIGH H 4WD LOW L THEFT BRAKE O/D OFF OFF DIM ON SET ACC OFF Turn signal control (pg. 64) Driver air bag (pg. 103) Wiper/washer control (pg.
Instrumentation Audio system (pg. 29) 4wd control* (pg. 139) 2WD 4X4 HIGH Auxiliary power point (pg. 28) VOL PUSH ON 4X4 LOW TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 3 4 AM/FM OFF ON OFF OFF PASSENGER AIRBAG Fog lamp control (pg. 20) Passenger air bag deactivate switch (pg. 108) Climate control system (pg.
Instrumentation WARNING LIGHTS AND CHIMES Check engine Your vehicle is equipped with a computer that monitors the engine’s CHECK emission control system. This ENGINE system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service technician in properly servicing your vehicle.
Instrumentation 3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.
Instrumentation Check gage Illuminates when the engine coolant CHECK temperature is high, the engine oil GAGE pressure is low or the fuel gauge is at or near empty. The ignition must be in the ON position for this lamp to illuminate. The lamp will also stay illuminated after the ignition is turned to the ON position. Refer to Engine coolant temperature gauge, Engine oil pressure gauge or Fuel gauge in this chapter for more information.
Instrumentation Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position ABS to indicate a system check. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released.
Instrumentation O/D off (if equipped) Illuminates when the Transmission O/D Control Switch (TCS), refer to OFF Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF. When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation. The light may also flash steadily if a transmission malfunction is detected.
Instrumentation Speed control This light comes on when either the SPEED SET/ACCEL or RESUME controls are pressed. It turns off when the CONT speed control OFF control is pressed, the brake or clutch (if equipped) is applied or the ignition is turned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter.
Instrumentation GAUGES Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The ignition should be in the OFF position while the vehicle is being refueled. When the gauge first indicates empty, there is a small amount of reserve fuel in the tank.
Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter.
Instrumentation Speedometer Indicates the current vehicle speed. 60 70 50 40 80 0 0 0 80 100 90 120 60 30 20 140 000000 40 km/h 120 MPH Odometer Registers the total kilometers (miles) of the vehicle. 60 70 50 40 80 0 0 0 100 80 90 120 60 30 20 Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control.
Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “L” and “H”). H If the gauge indicates low pressure, stop the vehicle as soon as safely L possible and switch off the engine immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and care chapter).
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. OFF Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is in either of the following positions: • Parking lamps • Low beams Press the foglamp control to activate the foglamps. The foglamp indicator light will illuminate. When the highbeams are activated, the foglamps will not operate.
Controls and features High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past DIM detent) to turn on interior and cargo lamps. • Rotate to full down position (past detent) to turn off interior and cargo lamps.
Controls and features CLIMATE CONTROL SYSTEM Heater only system (if equipped) OFF Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside of the vehicle. • • • • • • 22 OFF (Panel)-Distributes outside air through the instrument panel registers.
Controls and features Operating tips • In humid weather conditions, place the climate control system in DEF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, do not drive with the climate control system in the OFF position.
Controls and features Manual heating and air conditioning system (if equipped) OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. OFF A/C MAX A/C The air conditioning compressor can operate in all modes except and .
Controls and features • • • • • • (Panel)-Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. OFF-Outside air is shut out and the fan will not operate. For short periods of time only, use this mode to prevent undesirable odors from entering the vehicle. (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts.
Controls and features • To reduce humidity buildup inside the vehicle in warm weather conditions, don’t drive with the climate control system in the OFF position. • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct.
Controls and features To aid in defogging/demisting in cold weather conditions: 1. Select 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panel vents. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop. 4WD CONTROL (IF EQUIPPED) This control operates the 4WD.
Controls and features AUXILIARY POWER POINT SEEK 12V TUNE 1 2 3 4 AM-FM OFF A/C MAX A/C Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. This outlet should be used in place of the cigarette lighter for optional electrical accessories.
Controls and features PASSENGER AIR BAG ON/OFF SWITCH This switch must be used to deactivate the passenger air bag whenever a child seat is used in the right front or center front passenger seat position. Refer to Passenger air bag ON/OFF switchin the Seating and safety restraints chapter.
Controls and features Volume/power control Press the control to turn the audio system on or off. VOL PUSH ON Turn the control to raise or lower volume. VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode. AM/FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Controls and features Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio mode. Seek function in radio mode • Press to find the next listenable station down the frequency band.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the TONE control once, then use the volume knob to adjust the desired level. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TONE control twice, then use the volume knob to adjust the desired level. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Controls and features • • to decrease hours and to increase hours. To set the minute, press and hold the CLK control until CLOCK SET appears in the display and press the TUNE control: SEEK SEEK TUNE TUNE TONE CLK to decrease minutes and • SEEK SEEK to increase minutes. • TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time).
Controls and features AM/FM Stereo / Single CD Radio VOL - PUSH ON AM FM FM1 BASS SCN ST TREB BAL FADE CD CLK DISC SEEK EJ TUNE COMP DISCS CD 1 CD 2 SHUFFLE 3 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Controls and features AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Tune adjust The tune control works in radio and CD changer mode (if equipped).
Controls and features Tune adjust for CD changer (if equipped) • Press to select the previous SEEK disc in the CD changer. (Play will begin on the first track of the TUNE disc unless the CD changer is in DISCS shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio or CD mode.
Controls and features Scan function in radio mode Press SCN to hear a brief sampling of all listenable stations on the frequency band. Press SCN again to stop the scan mode. Scan function in CD mode Press SCN to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again.
Controls and features Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. FADE CD select • To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. AM FM CD Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Rewind The rewind control works in CD and CD changer (if equipped) modes.
Controls and features Eject function Press the control to stop and eject a CD. EJ Compression feature Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature (if equipped with CD changer) The shuffle feature operates in CD SHUFFLE changer mode only and plays all 6 tracks on the current disc in random order.
Controls and features To set the minute, press and hold the CLK control and press the TUNE control: • • SEEK TUNE DISCS to decrease minutes and to increase minutes.
Controls and features Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. Turn control to raise or lower volume. VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Controls and features Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio, tape or CD mode.
Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing. CLK If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control then press: • to decrease the treble output and to increase the treble output. • BASS SEL Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: to shift sound to the left and • to shift sound to the right.
Controls and features Tape select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached.
Controls and features Press the EJ control to stop and eject a CD. EJ DolbyT noise reduction Dolbyt noise reduction operates in tape mode. Dolbyt noise reduction 4 reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the Dolbyt noise reduction. Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing Corporation. “Dolbyt” and the double-D are registered trademarks of Dolbyt Laboratories Licensing symbol Corporation.
Controls and features Setting the clock To set the hour, press and hold the CLK control and press SEEK: AUTO CLK • • to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press TUNE: AUTO CLK to decrease minutes and • to increase minutes. • If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner.
Controls and features The CLK control will allow you to switch between media display mode AUTO (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 CLK seconds, when the radio is turned on, and then revert to clock information. Any time that the media is changed, (new radio station, etc.), the media information will again display for 10 seconds before reverting back to the clock.
Controls and features Volume/power control Press the control to turn the audio system on or off. PUSH ON Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes. AM FM CD AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Controls and features Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD mode • Press to select the previous disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.
Controls and features Seek function in CD mode • Press to seek to the previous track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing. • Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay. Scan function The scan function works in radio or CD mode.
Controls and features 4. Press and hold a memory preset control. The playing media will mute momentarily. When the sound returns, the station is held in memory on the control you selected. The display will read SAVED. Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1.
Controls and features CD select CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last. If an alternative CD is desired, press the corresponding preset control (1–6) of a loaded CD, or press the TUNE control to access the other loaded CDs. NO CD will display if the CD control is activated when there is not a CD present in the audio system.
Controls and features has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2. Auto load This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio. Press and hold the LOAD control until AUTOLOAD # is displayed. The CD door will open. Load the desired disc, one at a time. The CD is loaded into position and the audio system will display CD#.
Controls and features Rewind The rewind control works in CD modes. Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode. When in rewind mode, your audio system will automatically lower the volume level of the playing media. Fast forward The fast forward control works in CD modes. Press and hold the FF control until the desired selection is reached.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the TREB control. Use the SEL control to increase or decrease the amount of treble.
Controls and features Menu mode The MENU control allows you to MENU access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated. While in FM mode, two menus are available. If RDS is turned OFF, you can access the following: • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES — Refer to Setting the clock. • RDS OFF — Refer to Radio data system feature.
Controls and features Traffic announcements This feature allows you to hear traffic announcements. When in this MENU + SEL mode, traffic announcements will interrupt radio and CD play. When in FM mode and RDS is activated, press the MENU until TRAFFIC OFF displays. Press the SEL control to engage the feature. The display will read TRAFFIC ON. This feature also allows you to control the volume of traffic announcements.
Controls and features Radio data system (RDS) feature This feature allows your audio system to receive text information MENU + SEL from RDS-equipped FM radio stations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll through the following selections: Traffic announcements This feature allows you to hear traffic announcements while in CD mode.
Controls and features Program type This feature allows you to search for RDS stations selectively by their program type. Press the MENU control until FIND program type is displayed. MENU + SEL Use the SEL control to select the program type.
Controls and features Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Setting the clock Press the MENU control until SELECT HOUR or SELECT MINUTE is displayed. (The menu mode must be engaged to enable clock mode). Use the SEL control to manually set the time. SEL to increase • Press hours/minutes. • Press to decrease hours/minutes. Press the MENU control again to disengage the clock mode.
Controls and features Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. Radio reception factors Three factors can affect radio reception: • Distance/strength.The further an FM signal travels, the weaker it is.
Controls and features TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. Turn signal flasher reprogramming information During operation of the turn signals, if the lights flash faster or slower than the normal rate the vehicle has an electrical malfunction. The turn signal flasher can be reprogrammed by a dealer or qualified technician.
Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to 4 operate while the engine is not 3 running. 5 2. LOCK, locks the steering wheel, automatic transmission gearshift 2 lever and allows key removal. 3. OFF, shuts off the engine and all 1 accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine.
Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. ON OFF To set a speed • Press SET ACC. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RSM SET ACC COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Controls and features To set a higher set speed • Press and hold SET ACC. Release the control when the desired vehicle speed is reached or RSM • Press and release SET ACC to SET operate the Tap-Up function. ACC Each press will increase the set speed by 1.6 km/h (1 mph) or COAST • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET ACC. You can accelerate with the accelerator pedal at any time during speed control usage.
Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. Fully depressing the clutch pedal may cause a flare in engine RPM as the throttle is returned to idle. This is normal. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RSM. For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SPEED SET ACCEL or RES controls are pressed. It turns off when the speed CONT control OFF control is pressed, the brake or clutch is applied or the ignition is turned to the OFF position.
Controls and features The transmission will operate in all gears except overdrive. To return to O/D ON/OFF normal overdrive mode, press the Transmission Control Switch again. The TCIL will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will (Overdrive) mode. automatically return to normal For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter.
Controls and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push (tap) the end of the stalk briefly for a single swipe (no wash).
Controls and features POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
Controls and features POWER DOOR LOCKS (IF EQUIPPED) Press the top of the control to unlock all doors and the bottom to lock all doors. UNLOCK LOCK POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: to adjust the left 1. Select mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features.
Controls and features CARGO AREA FEATURES Cargo area shade (if equipped) Your vehicle may be equipped with notches in the side trim panels that are used for a cargo area shade. See your dealer for more information. BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extend the pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each side of the extender to release it from the pickup box. 3.
Controls and features 4. Evenly push down on the extender and push the round knobs in on each side locking it in place. Green markings on the shaft indicate the locked position. The locking clip screws below the middle bar can be tightened counterclockwise for extra security. To stow the bed extender, follow steps one through four in reverse order. The bed extender may be used to secure a load of up to 46 kg (100 lbs.) on the tailgate.
Controls and features To remove the bed extender: 1. Extend the bed extender. 2. Pull the round knobs on each side of the extender to unlock it. Make sure the locking clip screws are loose before removing the extender. 1. Press the locking clips below the middle bar on each side and lift the extender out of the channels on the “D” pillar. To install the bed extender, follow the removal procedure in reverse order.
Controls and features To open the front panel: • Open the lock cover and unlock the front panel. • Lift the panel to access items in the pickup box near the cab. The front panel will automatically lock when lowered onto the pickup box. • To close, lower the panel down on the pickup box. Do not drive with front panel unlocked or folded on top of the rear panel. To open the rear panel: • Lower the tailgate. • Release the tension on two retension straps by pushing the buttons on the straps and pulling.
Controls and features To stow the rear panel: • Before driving with the tonneau cover open, stow the rear panel. • Release four cylinder clips and remove two hydraulic cylinders from the pickup box and rear panel. • Lift the rear panel up, lay it on top of the front panel and secure it with the two straps on the front panel tiedowns. • Pull the straps to tighten the rear panel on to the front panel. Failure to secure the rear panel could damage the tonneau cover or vehicle.
Controls and features The cargo divider is designed to divide your pickup box in half or rotate 90° to allow you full use of the pickup box. To rotate the cargo divider 90°: • Open front panel. • Pull the lower release lever out on each side of the cargo divider to unlatch from the pickup box. • Rotate the divider 90° parallel with the tonneau cover and secure it to the pickup box with the lower release levers. To rotate the cargo divider back, follow the procedure in reverse order.
Controls and features To remove the tonneau cover: The tonneau cover needs to be supported during removal. This is a two person operation. • Remove the cargo divider, refer to To remove the cargo divider in this procedure. • Open and support the front panel. • Release four cylinder clips and remove the two hydraulic cylinders from the front panel. Close the front panel. • Stow the rear panel on top of the front panel, refer to To stow the rear panel in this procedure.
Controls and features To open the tonneau cover from the inside, pull the “T” shaped handle and push up on the tonneau cover panel. The material that the handle is made of will glow for hours in the darkness of the pickup box following brief exposure to ambient light. The “T” shaped handle is located on the tonneau cover panel. Keep vehicle doors and tonneau cover locked and keep keys out of a child’s reach. Unsupervised children could lock themselves in an open pickup box and risk injury.
Controls and features The remote entry features only operate with the ignition in the LOCK position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors.
Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Panic alarm will only operate with the ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Controls and features Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prio
Controls and features Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the RUN or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.
Controls and features Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your dealership. Your dealership can program your key or you can “do it yourself”, refer to Programming spare keys. Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the coded key may cause vehicle starting issues.
Controls and features If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a dealership or locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded. Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle.
Controls and features 1. Insert the first previously programmed coded key into the 4 ignition and turn the ignition from 3 3 (OFF) to 4 (ON) (maintain ignition 5 in 4 (ON) for at least one second). 2. Turn ignition to 3 (OFF) then 2 2 (LOCK) and remove the first coded key from the ignition. 1 3.
Seating and safety restraints SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Seating and safety restraints Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard and down on the seat handle. To stow the seat, pull seat bottom back to the fully upright position. Do not install a child seat in a center facing jump seat.
Seating and safety restraints Center facing jump seat (4 door SuperCab) (if equipped) To open, pull seat assembly down, then raise seatback. To stow the seat, fold seat back down and raise seat assembly to the fully upright position. Do not install a child seat in a center facing jump seat. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder.
Seating and safety restraints The front outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger outboard safety belt has two types of locking modes described below: Energy Management Feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.
Seating and safety restraints The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter.
Seating and safety restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly.
Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. • Regular Cab and 4–door Super Cab • 2–door SuperCab To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up.
Seating and safety restraints Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Lap belts Adjusting the front center seat lap belt (if equipped) The lap belt does not adjust automatically. The lap belt should fit snugly and as low as possible around the hips, not across the waist.
Seating and safety restraints Adjusting the rear center facing jump seat lap belt (if equipped) The lap belt will adjust automatically. To fasten, grasp the tongue, and with a continuous motion, pull out enough webbing to buckle the tongue into the correct buckle. If you did not pull out enough webbing to reach the buckle, allow the tongue to retract fully before trying to pull it out again. The lap belt should fit snugly and as low as possible around the hips, not across the waist.
Seating and safety restraints If... Then... The driver’s safety belt is buckled The safety belt warning light and before the ignition switch is turned indicator chime remain off. to the ON position... Belt minder The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. If..
Seating and safety restraints Reasons given... “Belts are uncomfortable” Consider... We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. “I was in a hurry” Prime time for an accident. Belt Minder reminds us to take a few seconds to buckle up.
Seating and safety restraints Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure. The Belt Minder feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set. • The gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission). • The ignition switch is in the OFF position.
Seating and safety restraints • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by the safety belt warning light flashing four times per second for three seconds. 8. Confirmation of enabling Belt Minder is provided by: • The safety belt warning light flashing four times per second for three seconds. • Followed by three seconds with the safety belt warning light off.
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 60 70 50 80 100 20 E L 90 120 60 30 H 10 ABS 80 0 0 0 40 CHECK ENGINE F 140 000000 40 160 H H 110 km/h 120 MPH P 100 180 20 R N D 2 1 L BRAKE ! P SPEED CONT O/D OFF L SEEK OFF TUNE RSM ON SET ACC OFF 2 1 3 4 AM-FM COAST SRS OFF A/C MAX A/C ON OFF OFF PASSENGER AIRBAG Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and s
Seating and safety restraints National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Never place a rear facing infant seat in the front seat unless the passenger air bag is turned off.
Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Failure to follow these instructions may increase the risk of injury in a collision. An infant in a rear-facing seat faces a high risk of serious or fatal injuries from a deploying passenger air bag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger air bag is turned off.
Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and safety restraints • and the electrical wiring which connects the components. The RCM (restraints control module) monitors its own internal circuits and the supplemental air bag electrical system warning (including the passenger air bag deactivation switch, the impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors).
Seating and safety restraints Passenger air bag ON/OFF switch An air bag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings. Failure to put the switch in a proper position can increase the risk of serious injury or death in a collision. Turning the passenger air bag off 1.
Seating and safety restraints Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turn the switch to ON. ON OFF 2. The OFF light will briefly illuminate when the ignition is OFF turned to ON. This indicates that the passenger air bag is operational.
Seating and safety restraints The vast majority of drivers and passengers are much safer with an air bag than without. To do their job and reduce the risk of life threatening injuries, air bags must open with great force, and this force can pose a potentially deadly risk in some situations, particularly when a front seat occupant is not properly buckled up.
Seating and safety restraints 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger air bag to pose a special risk for the passenger; and • makes the potential harm from the passenger air bag in a crash greater than the potential harm from turning OFF the air bag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.
Seating and safety restraints • the child has a medical condition that, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’s condition. 3.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions.
Seating and safety restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and safety restraints • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating positions) (if equipped) section in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps. in this chapter.
Seating and safety restraints Rear facing child seats should NEVER be placed in the front seats unless the passenger airbag switch is turned off. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4.
Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and safety restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The tether anchors in your vehicle are located on the back of the front seat cushion.
Seating and safety restraints 3. Locate the correct anchor for the selected seating position. The tether anchor is located on the rear lower portion of the passenger seat.
Seating and safety restraints 4. Clip the tether strap to the anchor.
Seating and safety restraints Center seating location When installing a child safety seat in the center position, route the tether strap over the center arm rest and clip it to the center anchor.
Seating and safety restraints Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinyl seat, route the tether strap through the guiding sleeve and clip it to the center anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • If • • Make sure the gearshift is in P (Park). starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Starting Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Cold weather starting (flexible fuel vehicles only) As the outside temperature approaches freezing, ethanol fuel distributors should supply winter grade (Ed85) ethanol (same as with unleaded gasoline).
Starting If the engine fails to start using the preceding instructions 1. Press the accelerator pedal 1/3 to 1/2 of the way to floor and hold. 2. Turn the key to START position. 3. When the engine starts, release the key, then release the accelerator pedal gradually as the engine speeds up. 4. If the engine still fails to start, repeat steps one through three. 5. After the engine starts, hold your foot on the brake pedal, put the gearshift lever in gear and release the parking brake.
Starting (-10°F) or below. Your engine block heater also comes with a battery warmer. The battery warmer wraps around the battery and keeps the battery warm when the engine block heater is plugged in. For best results, plug the heater in at least three hours before starting the vehicle. Using the heater for longer than three hours will not harm the engine, so the heater can be plugged in the night before starting the vehicle.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving steering control of your vehicle and, providing there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. • The anti-lock system does not decrease the time necessary to apply the brakes or always reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop. • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! BRAKE Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Driving If the steering wanders or pulls, the condition could be caused by any of the following: • underinflated tire(s) on any wheel(s) • uneven vehicle loading • high crown in center of road • high crosswinds • wheels out of alignment • loose or worn suspension components PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Driving Your vehicle has the capability to haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling people and cargo may raise the center of gravity of the vehicle. Use extra caution while becoming familiar with your vehicle. Know the capabilities and limitations of both you as a driver and your vehicle.
Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 5–speed automatic transmission (if equipped) Your automatic transmission electronically controls the shift feel by using an adaptive learning strategy. This feature is designed to increase durability, and provide consistent shift feel over the life of the vehicle.
Driving Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This position locks the transmission and prevents the rear wheels from turning. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.
Driving Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the (Overdrive) position. The TCIL will illuminate on the instrument cluster. Transmission operates in gears one through four. Drive (O/D OFF) provides more engine braking than (Overdrive) and is useful whenever driving conditions (i.e., city traffic, hilly terrain, etc.
Driving Manual transmission operation (if equipped) Using the clutch Vehicles equipped with a manual transmission have a starter interlock that prevents starting the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission: 1. Hold down the brake pedal. 2. Depress the clutch pedal. 3. Put the gearshift lever in N (Neutral). 4. Start the engine and let it idle for a few seconds. • Put the gearshift lever in 1 (First) or R (Reverse). 5.
Driving 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Driving Upshifts when accelerating (for best fuel economy) Maximum downshift speeds Transfer case position (if equipped) Shift from: 4H 4L 5 (Overdrive) - 4 88 km/h (55 mph) 34 km/h (22 mph) 4-3 72 km/h (45 mph) 27 km/h (18 mph) 3-2 56 km/h (35 mph) 21 km/h (14 mph) 2-1 32 km/h (20 mph) 11 km/h (8 mph) Reverse Ensure that the vehicle is at a complete stop before shifting into R (Reverse). Failure to do so may damage the transmission.
Driving 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions. If these lights illuminate when driving in 2WD, contact your Ford dealer as soon as possible. • 4WD HIGH-momentarily illuminates when the vehicle is started. Illuminates when 4H (4WD High) is engaged. • 4WD LOW–momentarily 4WD illuminates when the vehicle is LOW started. Illuminates when 4L (4WD Low) is engaged.
Driving Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WD 4X4 position at any forward speed. 4X4 HIGH LOW 2WD • You do not need to operate the vehicle in R (Reverse) to disengage your front hubs. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4X4 LOW position.
Driving 4. Move the 4WD control to the 2WD position. 2WD 4X4 HIGH 4X4 LOW Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4X4 HIGH or 4X4 LOW position.
Driving You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’s portfolio. If your vehicle gets stuck If the vehicle is stuck it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear.
Driving Water intrusion into the transmission may damage the transmission. Replace rear axle lubricant any time the axle has been submerged in water. The rear axle does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair is required. Driving on hilly or sloping terrain When driving on a hill, avoid driving crosswise or turning on steep slopes. You could lose traction and slip sideways.
Driving TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver.
Driving • GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification. • GVWR (Gross Vehicle Weight Rating): Maximum permissable total weight of the base vehicle, occupants, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system.
Driving The Safety Certification Label, found on the driver’s door pillar, lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations. If you are adding weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the front axle reserve capacity (FARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.e.
Driving 3. Subtract your loaded vehicle weight from the maximum GCWR on the following charts. This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart. TRAILER TOWING Your vehicle may tow a class I, II or III trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts.
Driving 2.3L 4x2 w/manual transmission Regular Cab w/7’ box All 2 177 (4 800) 726 (1 600) 3.0L 4.0L All All 2.3L All 2 722 (6 000) 3 175 (7 000) SuperCab 2 177 (4 800) Equal to frontal area of vehicle 1 179 (2 600) 4.64 (50) 1 597 (3 520) 4.64 (50) 671 (1 480) Equal to frontal area of vehicle 1 125 (2 480) 4.64 (50) 3.0L All 2 722 (6 000) (non-torsion bar suspension) 3.0L (torsion All 2 722 (6 000) 1 052 (2 320) 4.64 (50) bar suspension) 4.0L All 3 175 (7 000) 1 542 (3 400) 4.
Driving Engine Rear axle ratio 3.0L 4.0L All All 3.0L 4.0L All All 4x4 w/manual transmission Maximum Maximum GCWR - kg trailer weight (lbs.) - kg (lbs) Regular Cab w/6’ box 2 722 (6 000) 1 180 (2 3 175 (7 000) 1 506 (3 Regular Cab w/7’ box 2 722 (6 000) 1 061 (2 3 175 (7 000) 1 479 (3 SuperCab 2 722 (6 000) 1 007 (2 3 175 (7 000) 1 424 (3 3 175 (7 000) 1 234 (2 Maximum frontal area of trailer m2 (ft2) 380) 320) 4.64 (50) 4.64 (50) 340) 260) 4.64 (50) 4.64 (50) 3.0L All 220) 4.64 (50) 4.
Driving Engine 2.3L Maximum frontal area of trailer m2 (ft2) All Equal to frontal area of vehicle 3 402 (7 500) 1 869 (4 120) 4.64 (50) All 3 402 (7 500) 1 814 (4 000) 4.64 (50) All 4 309 (9 500) 2 740 (6 040) 4.64 (50) All 4 309 (9 500) 2 685 (5 920) 4.64 (50) 2.3L All Regular Cab w/7’ box 2 495 (5 500) 1 007 (2 220) 3.0L 4.0L All All 3.0L (non-torsion bar suspension 3.0L (tosion bar suspension) 4.0L (non-torsion bar suspension) 4.
Driving 4x2 w/automatic transmission SuperCab All 3 402 (7 500) 1 787 (3 940) 3.0L 4.64 (50) (non-torsion bar suspension) 3.0L (torsion All 3 402 (7 500) 1 715 (3 780) 4.64 (50) bar suspension) All 4 309 (9 500) 2 667 (5 880) 4.64 (50) 4.0L (non-torsion bar suspension) 4.0L (torsion All 4 309 (9 500) 2 595 (5 720) 4.64 (50) bar suspension) For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft.) elevation.
Driving Engine 3.0L 4.0L 3.0L 4.0L 4x4 w/automatic transmission Rear Maximum Maximum Maximum axle GCWR - kg trailer frontal area ratio (lbs.) weight - kg of trailer (lbs.) m2 (ft2) Regular Cab w/6’ box All 3 402 (7 500) 1 751 (3 860) 4.64 (50) All 4 309 (9 500) 2 622 (5 780) 4.64 (50) Regular Cab w/7’ box All 3 402 (7 500) 1 724 (3 800) 4.64 (50) All 4 309 (9 500) 2 595 (5 720) 4.64 (50) SuperCab All 3 402 (7 500) 1 669 (3 680) 4.64 (50) All 4 309 (9 500) 2 540 (5 600) 4.
Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches For towing trailers up to 907 kg (2 000 lb), use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure. Use a frame-mounted weight distributing hitch for trailers over 907 kg (2 000 lb).
Driving Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Using a step bumper The optional step bumper is equipped with an integral hitch and requires only a ball with a 19 mm (3/4 inch) shank diameter. The bumper has a 907 kg (2 000 lb.) trailer weight and 91 kg (200 lb.) tongue weight capability.
Driving Refer to the following chart for information regarding the factory-equipped trailer tow connector: Trailer tow connector Color Function 1. Dark Green Trailer right-hand turn signal 2. Yellow Trailer left-hand turn signal 3. Tan/White Tail lamp 4. White Ground Comment Circuit activated when brake pedal is depressed or when ignition is on and right-hand turn signal is applied. Circuit activated when brake pedal is depressed or when ignition is on and left-hand turn signal is applied.
Driving Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be no more than 10–15% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts.
Driving 4x2 and 4x4 vehicles equipped with manual transmissions Before you have your vehicle towed: • Release the parking brake. • Move the gearshift to N (Neutral). • Turn the key in the ignition to the OFF/UNLOCKED position. • The maximum recommended speed is 88 km/h (55 mph). • The maximum recommended distance is unlimited. In addition, it is recommended that you follow the instructions provided by the after market manufacturer of the towing apparatus if one has been installed.
Roadside emergencies Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic Warranty’s Roadside Assistance expiring. For more information and enrollment, contact 1–877–294–2582 or visit our website at www.ford.ca.
Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components. NOTE: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left-hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. 28 24 20 16 12 8 4 To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Fuse Amp Rating 5A 10A Passenger Compartment Fuse Panel Description Power Mirror Switch Daytime Running Lights (DRL), Back-up Lamps, Transmission, Passenger Air Bag Deactivation Switch, Blower Motor Relay 7.5A Right Stop/Turn Trailer Tow Connector — Not Used 15A 4x4 Control Module — Not Used 7.5A Left Stop/Turn Trailer Tow Connector — Not Used 7.5A Brake Pedal Position Switch 7.
Roadside emergencies Fuse/Relay Location 17 Fuse Amp Rating 20A 18 19 20 — 25A 7.5A 21 22 23 24 15A 20A — 7.5A 25 26 — 10A 27 28 — 7.
Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies 2.
Roadside emergencies Fuse/Relay Location 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Fuse Amp Rating — — 40A** 20A** — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* — 15A* — — — — 10A* — — 20A* 10A* — — Power Distribution Box Description Not Used Not Used Blower Motor Auxiliary Cooling Fan Not Used Not Used Not Used PCM Memory Not Used Fuel Pump Motor Headlamps A/C Clutch Solenoid Not Used Not Used 4WABS Module Not Used Trailer Tow Foglamps, DRL Not Used P
Roadside emergencies Fuse/Relay Location 45A 45B 46A 46B 47 48 49 50 51 52 53 Fuse Amp Rating — — — — — — — — — — — 54 — 55 — 56A — 56B — * Mini Fuses ** Maxi Fuses 168 Power Distribution Box Description Wiper HI/LO Wiper Park/Run Fuel Pump Trailer Tow Starter Auxiliary Cooling Fan Not Used Not Used Not Used Not Used Powertrain Control Module (PCM) Diode Powertrain Control Module (PCM) Blower A/C Clutch Solenoid Front Washer Pump
Roadside emergencies 3.0L and 4.
Roadside emergencies 170 Fuse/Relay Location 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Fuse Amp Rating — — 40A** — — — — 10A* — 20A* 30A* 10A* — — 30A* — 15A* 20A* 32 33 34 35 36 37 38 39 40 41 42 43 — 15A* — — — — 10A* — — 20A* 10A* — Power Distribution Box Description Not Used Not Used Blower Motor Not Used Not Used Not Used Not Used PCM Memory Not Used Fuel Pump Motor Headlamps A/C Clutch Solenoid Not Used Not Used 4WABS Module Not Used Trailer Tow Foglamps, Daytime Running Lamps (DRL)
Roadside emergencies Fuse/Relay Location 44 45A 45B 46A 46B 47A 47B 48A 48B 49 50A 50B 51 52 53 Fuse Amp Rating — — — — — — — — — — — — — — — 54 — 55 — 56A — 56B — * Mini Fuses ** Maxi Fuses Power Distribution Box Description Not Used Wiper High/Low Wiper Park/Run Not Used Front Washer Pump Not Used Not Used Fog Lamps Fog Lamp Relay Full Starter Not Used Fuel Pump Not Used Not Used Powertrain Control Module (PCM) Diode Powertrain Control Module (PCM) Blower A/C Clutch Solenoid Trailer Tow CHANGING THE T
Roadside emergencies It is not recommended that the vehicle be operated in 4WD modes with a temporary spare. If 4WD operation is necessary, do not operate above speeds of 16 km/h (10 mph) or for distances above 80 km (50 miles). If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Location Under the vehicle, just forward of the rear bumper Jack, jack handle, Regular Cab: behind seats and underneath the wheel nut wrench jack and tools cover SuperCab: stowed in the passenger side rear cab compartment or behind the jump seat in a separate tool bag Four-door models: stowed behind the front seats, between jump seats and underneath jack
Roadside emergencies 2. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. 3. Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate. Forward motion will stop and resistance to turning will be felt when properly engaged. 4. Turn the handle counterclockwise until tire is lowered to the ground and the cable is slightly slack. 5.
Roadside emergencies Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. Turn the spare handle clockwise until the tire is raised to its original position underneath the vehicle. The spare handle ratchets when the tire is raised to the stowed position. It will not allow you to overtighten. 4.
Roadside emergencies 3. Block the diagonally opposite wheel. 4. Insert tapered end of the lug wrench behind hub caps and twist them off. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Roadside emergencies • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the differential as a jacking point. 7. Remove the wheel lug nuts with the lug wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Roadside emergencies 10. Remove the jack and fully tighten the lug nuts in the order shown. 11. Stow the flat tire. Refer to Stowing the spare tire. 12. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 13. Unblock the wheels. 1 3 4 5 2 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Roadside emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and care 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. • Manual transmission: 1.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (manual transmission) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and care 3.0L V6 engine 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick (if equipped) 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid reservoir (if equipped) 9. Battery 10. Power steering fluid reservoir 11.
Maintenance and care 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir (if equipped) 8. Battery 9. Power steering fluid reservoir 10. Air filter assembly 11.
Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and care • 3.0L V6 engine • 4.
Maintenance and care 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • 2.3L I4 engine • 3.
Maintenance and care • 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and care Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft (Part: XO–5W20–QSP in U.S.)or an equivalent oil meeting Ford Specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Maintenance and care SAE 5W-30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft (Part: XO–5W30–QSP in U.S.) or an equivalent oil meeting Ford Specification WSS-M2C153–G. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty.
Maintenance and care 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until MAX the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists.
Maintenance and care 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. 2. Remove cap and rubber diaphragm from reservoir. 3. Add fluid until the level reaches the step in the reservoir. 4. Reinstall rubber diaphragm and cap onto reservoir. WINDSHIELD WASHER FLUID SHER FL WA UID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir.
Maintenance and care Note:Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and water, which equates to a freeze point of -36° C (-34° F).
Maintenance and care • 3.0L and 4.0L engines RADIATOR COOLANT ONLY When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and care Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Maintenance and care • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Use of Recycled Engine Coolant section). For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “cold full” level.
Maintenance and care If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Your cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored).
Maintenance and care If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage.
Maintenance and care 3. Turn the engine off. 4. If your vehicle is equipped with a 3.0L V6 engine, check the fluid level on the dipstick. It should be within the FULL HOT range. Do not add fluid if the level is within this range. 5. If your vehicle is equipped with a 4.0L SOHC V6 or 2.3L I4 engine, check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 6.
Maintenance and care 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface.
Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 ml (1/2 pint) increments through the filler tube until the level is correct.
Maintenance and care 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3.
Maintenance and care DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance guide for maintenance intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
Maintenance and care If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Maintenance and care RN LE TU AD RE 6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is disconnected or a new battery installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly.
Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Certification Label. Tire pressure information can also be found on the Tire Information label located on the inside of the fuel filler door.
Maintenance and care • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label.
Maintenance and care Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control.
Maintenance and care • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure.
Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and care Pure ethanol is the alcohol which is the intoxicating agent in liquor, beer and wine. It is distilled from the fermentation of plants such as field corn and sugar cane. When ethanol is used in the making of motor fuels, a small amount of a bad tasting chemical is added to discourage beverage use. The resulting fuel is called Ed100 meaning 100% pure ethanol diluted by 2% to 5% gasoline as the “denaturant.” Fuel ethanol (E85)d is then made by adding 15% more unleaded gasoline.
Maintenance and care Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position. Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature.
Maintenance and care If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. If your vehicle is a flexible fuel vehicle (FFV), use only UNLEADED FUEL and ETHANOL(E85).
Maintenance and care U.S. government regulations require fuel ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation E85 or the appropriate percentage for that region. Use of other fuels such as Fuel Methanol may cause powertrain damage, a loss of vehicle performance, and your warranty may be invalidated.
Maintenance and care Standards for fuel ethanol have been developed to provide FFVs the best possible performance, safety and durability. To assist alcohol fuel providers in meeting these standards, guidelines have also been developed which prescribe “Ethanol Fuel Compatible” dispensing station equipment. These standards and guidelines can be obtained from Ford Motor Company. Fuel stations may apply to be certified as meeting these standards. However, not all stations meet these standards at this time.
Maintenance and care ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000 miles) of driving (engine break-in period).
Maintenance and care Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5.
Maintenance and care • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy.
Maintenance and care • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle.
Maintenance and care Illumination of the “Check Engine” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly. Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
Maintenance and care BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Foglamps • High-mount brakelamp • Brakelamps • Turn signals • License plate lamp • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs To remove the headlamp bulb: 1.
Maintenance and care 5. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 6. Without turning, remove the old bulb by gently pulling it straight back out of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Maintenance and care Replacing front side marker bulbs 1. Open the hood. 2. Remove two screws and cover (if equipped). 3. At the back of the headlamp, pry up the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward. 4. Remove screw(s) from lamp assembly. 5. Disengage lamp assembly (it has a snap fit).
Maintenance and care 6. Rotate bulb socket counterclockwise and remove from lamp assembly. 7. Carefully pull bulb straight out of socket and push in the new bulb. 8. Install the bulb socket in lamp assembly by turning clockwise. 9. Align the lamp on the vehicle and push to snap in place. 10. Install screw(s) on lamp assembly. 11. Install the headlamp on vehicle, push rearward and secure with two retainer pins. 12. Install the cover with two screws (if equipped).
Maintenance and care 3. Rotate bulb socket counterclockwise turn and remove from lamp assembly. 4. Carefully pull the bulb straight out of the socket and push in the new bulb. 5. Install the bulb socket in lamp assembly by turning clockwise. 6. Install the lamp assembly and secure with four screws. Replacing foglamp bulbs 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3.
Maintenance and care To remove the brakelamp assembly: 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it counterclockwise. 3. Carefully pull bulb straight out of socket and push in the new bulb. To install the brakelamp assembly: 1. Install the bulb socket into the lamp assembly by rotating clockwise. 2. Install the lamp assembly on the vehicle and secure with two screws.
Maintenance and care Function Number of bulbs Trade number Park/turn/side marker 2 3457 lamps (front) 2 194 Headlamps 2 9007 Foglamps (if 2 9145 equipped) Hi-mount brakelamp 1 922 Cargo lamps 2 906 Rear stop/turn/tail 2 3157 lamps Rear license plate 2 194 lamps Backup lamp 2 3156 Dome lamp 1 912 Glove compartment 1 194 Map/dome-SuperCab 2 904 (if equipped) Map/dome-Regular 1 904 Cab (if equipped) 1 904 All replacement bulbs are clear in color except where noted.
Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
Maintenance and care Use only carnauba or synthetic-based waxes. Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle. Use tar remover to remove any tar spots. Avoid getting wax on the windshield, or on any surfaces which appear coarse or bumpy. If you have wax applied at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.
Maintenance and care Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block or other engine components. • Cover the highlighted areas to prevent water damage when cleaning the engine. • 2.
Maintenance and care • 3.0L • 4.0L • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Maintenance and care Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the windshield, wiper blades and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent.
Maintenance and care Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery Oil filter PCV valve Spark plugs* 2.3L I4 engine 3.0L V6 engine FA-1658 FA-1658 4.0L V6 engine FA-1658 FG–1002 BXT-59 FL-400S EV-227 AWSF-32FEM** FG–1002 BXT-59 FL-820S EV-225 AGSF-34FP FG–1002 BXT-59 FL-400S EV-130 AWSF-32PP*** * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. ** Two spark plugs per cylinder required (eight total).
Capacities and specifications Fluid Power steering fluid Transmission fluid 1 Engine coolant 4 Ford Part Name Motorcraft MERCONt ATF Application Capacity All Fill to range on dipstick or reservoir Motorcraft 5-speed manual 2.65L (2.8 MERCONt ATF quarts) 3 Motorcraft 4x2 vehicles with 9.4L (9.9 quarts) 2 MERCONtV ATF automatic and 2.3L I4 engine 4x2 vehicles with 9.5L (10.0 automatic and quarts)2 3.0L or 4.0L engines 4x4 vehicles with 9.8L (10.3 automatic and quarts) 2 3.0L or 4.0L Motorcraft 2.
Capacities and specifications Fluid Fuel tank Transfer case Fluid Front axle lubricant Rear axle lubricant5 Windshield washer fluid Ford Part Name N/A Motorcraft MERCONt ATF Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Ultra-Clear Windshield Washer Concentrate Application Capacity Regular cab (Short wheel base) Regular cab (Long wheel base) SuperCab 62.4L (16.5 gallons) 4x4 Vehicles 4x4 Vehicles 75.7L (20.0 gallons) 73.8L (19.5 gallons) 1.
Capacities and specifications 4 Add the coolant type originally equipped in your vehicle. Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole.
Capacities and specifications Ford part name or equivalent 2.3L and 3.0L engines Motorcraft SAE 5W-20 Super Premium Motor Oil Engine oil 4.0L engines Motorcraft SAE 5W-30 Super Premium Motor Oil Hinges, door Multi-Purpose checks, latches, Grease striker plates, fuel filler door hinge and seat tracks Transmission/ Motorcraft steering/parking Premium brake linkages Long-Life Grease and pivots, brake and clutch pedal shaft, clutch pilot bearing and.
Capacities and specifications Item Windshield washer fluid Ford part name or equivalent Ultra-clear Windshield Washer Concentrate Ford part number Ford specification C9AZ-19550-AC ESR-M17P5-A 1 Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. 2 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
Capacities and specifications VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height 4x2/4x4 (4) Wheelbase (5) Track Front (5) Track Rear Regular Cab Short Wheel Base (SWB) mm (in) 4 763 (187.5) Regular Cab Long Wheel Base (LWB) mm (in) 5 093 (200.5) 5 153 (202.9) 1 785 (70.3) 1 785 (70.3) 1 785 (70.3) 1 1 2 1 1 1 2 1 1 1 3 1 575 655 831 486 (62.0) / (65.2) (111.4) (58.5) 1 455 (57.3) (62.4) / (65.2) (117.4) (58.5) 1 455 (57.
Capacities and specifications 4 1 4 1 247
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side. Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel.
Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • Benefits during the warranty period depending on the plan you purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).
Customer assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern cannot be resolved at the dealership level, please contact the Ford Customer Relationship Center.
Customer assistance In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O. Box 6248 Dearborn, Michigan 48121 1-800-521-4140 (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O.
Customer assistance THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Customer assistance Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer assistance Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer.
Customer assistance Comfort and convenience Air conditioning Battery warmer Cargo organizers Cargo retention net Cargo shades (Super Cab 2 door) Engine block heaters Manual sliding rear window Tire step Underbody lighting Travel equipment Automatic headlamp system with DRL Bed extender Bed rail caps Bed tent (Short bed, Styleside only) Cellular phone holder Compass mirror Compass mirror with outside temperature reading Daytime running lights First aid kit Fog lights Heavy-duty battery Peace of mind kit Pick
Customer assistance Protection and appearance equipment Air bag anti-theft locks All weather slush mats Bed mat/tailgate kit Bed hooks Bed mats Bedliners Carpeted floor mats with logo Door edge guards Front end covers (full and sport) Bug deflectors Instrument panel trim (brushed aluminum) Locking gas cap Lubricants and oils Rally bar with off road lighting Rear window deflector Side window air deflectors Skid plate Spare tire lock Step bumpers Tailgate lock Tailgate protector Tonneau covers — soft (snap an
Customer assistance • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
Customer assistance attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index A B Air bag supplemental restraint system ........................................103 and child safety seats ............105 description ..............................103 disposal ....................................107 driver air bag ..........................105 indicator light ...................12, 107 operation .................................105 passenger air bag ...................105 passenger deactivation switch ................................29, 108 Air cleaner filter ...................
Index Cleaning your vehicle ...............234 engine compartment ..............236 exterior ....................234–235, 239 exterior lamps .........................238 instrument cluster lens ..........238 instrument panel ....................238 interior .....................................239 mirrors .....................................239 plastic parts ............................237 safety belts ..............................239 washing ....................................234 waxing ................
Index lubrication specifications ......243, 245 refill capacities ........................240 service points ..................186–188 starting after a collision .........159 Engine block heater .................126 Engine oil ..................................189 checking and adding ..............189 dipstick ....................................189 filter, specifications ........193, 240 recommendations ...................193 refill capacities ........................240 specifications ..................
Index H K Hazard flashers .........................159 Headlamps ...................................20 aiming ......................................233 bulb specifications ..................232 daytime running lights .............20 flash to pass ..............................21 high beam ...........................13, 21 replacing bulbs .......................227 turning on and off ....................20 warning chime ..........................15 Heating ........................................
Index trailer towing ..........................144 Loading instructions .................146 Lubricant specifications ...243, 245 Lumbar support, seats ...............90 fluid, specifications .........243, 245 Preparing to drive your vehicle ........................................131 M Radio ............................................29 Relays ........................................161 Remote entry system ...........81, 83 illuminated entry ......................85 locking/unlocking doors ...........
Index Servicing your vehicle ..............184 Snowplowing .................................4 Spark plugs, specifications .............240, 245–246 Special notice ................................4 ambulance conversions ..............5 utility-type vehicles ....................4 Specification chart, lubricants ...........................243, 245 Speed control ..............................65 Speedometer ...............................18 Starting your vehicle ........123, 126 jump starting ...................
Filling station information Item Required fuel Fuel tank capacity (Regular cab-Short wheel base) Fuel tank capacity (Regular cab-Long wheel base) Fuel tank capacity (SuperCab) Engine oil capacity (includes filter change)-2.3L I4 engine Information Unleaded fuel only - 87 octane 62.4L (16.5 gallons) 75.7 (20.0 gallons) 73.8L (19.5 gallons) 3.8L (4.0 quarts). Use Motorcraft SAE 5W-20 Super Premium Motor Oil, Ford specification WSS-M2C153-H. Engine oil capacity (includes filter 4.3L (4.5 quarts).
Filling station information Item Power steering fluid capacity Information Fill to range on dipstick. Use Motorcraft MERCONt ATF. Manual transmission fluid capacity 2.65L (2.8 quarts). Use Motorcraft 2 MERCONt ATF. 3 Automatic transmission fluid 9.4L (9.9 quarts). Use Motorcraft capacity-4x2 vehicles with 2.3L I4 MERCONtV ATF. engines 2 Automatic transmission fluid 9.5L (10.0 quarts). Use Motorcraft capacity-4x2 vehicles with 3.0L or MERCONtV ATF. 4.0L engines 2 9.8L (10.3 quarts).
