Table of Contents Table of Contents Introduction Instrument Cluster 4 10 Warning and control lights Gauges 10 12 Entertainment Systems 15 AM/FM stereo with CD 15 Climate Controls Manual heating and air conditioning Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors 19 19 20 21 21 22 23 24 24 25 26 26 Locks and Security 28 Keys Locks Anti-theft system 28 28 33 Seating an
Table of Contents Tires, Wheels and Loading Tire Information Changing tires Wheel lug nut torque Vehicle loading Driving 66 67 71 79 89 95 Starting Brakes Transmission operation 95 99 102 Roadside Emergencies 105 Getting roadside assistance Hazard flasher switch Fuel shut-off switch Fuses and relays Jump starting Customer Assistance Reporting safety defects (U.S.
Table of Contents Accessories 175 Scheduled Maintenance Guide 177 Normal Scheduled Maintenance and Log Motorcraft Premium Gold Coolant Change Record Index 180 190 192 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Introduction Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction • how far (if at all) the driver was depressing the accelerator and/or the brake pedal; • how fast the vehicle was traveling; and • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connected to the recording modules.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap Low tire warning MAX MIN 9 2
Instrument Cluster Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the lights work. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately. Anti-lock brake system: Illuminates indicating an ABS fault. ABS If the lamp stays on for more than a few seconds, then an ABS fault is indicated, have the system serviced immediately.
Instrument Cluster Door ajar: Illuminates when the ignition is in the ON position and any door, trunk or the engine cover is ajar. DOOR AJAR Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check the tail lamps for proper function. High beams: Illuminates when the high beam headlamps are turned on. Defrost: Illuminates when the rear window defroster is turned on.
Instrument Cluster Never remove the coolant reservoir cap while the engine is running or hot. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Engine oil pressure gauge: Indicates engine oil pressure. If the pointer drops to the red section when the engine is running, stop your vehicle as soon as possible, shut off the engine and check the oil tank level. Add oil if necessary.
Instrument Cluster Boost/Vac gauge: Boost VAC shows that supercharger boost and engine vacuum are functioning properly. If no boost or reduced boost is shown, have engine checked. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. Refer to Filling the tank in the Maintenance and Specifications chapter for more information.
Entertainment Systems Entertainment Systems AM/FM MCINTOSH CD SYSTEM A flashing anti-theft indicator (Disc in lamp), may be activated and de-activated by pressing and holding the CD Eject control for two seconds or more with the radio turned off. 1. CD door: Insert a CD label side up. Once loaded, the “Disc in” indicator light will illuminate and playback begins automatically. 2. Eject: Press to eject a CD when the power is on or off. 3.
Entertainment Systems 4. AM/FM: Press to select a frequency band (FM1/FM2/FM3/AM). The selected band appears in the display. Displaying the Clock:While pressing and holding the AM/FM band control, press and release the #4 preset control. Each time this operation is performed, the display will toggle between the selected mode (Radio, CD) and clock mode. Setting the Clock: Set the display to clock mode. (Press and hold AM/FM while you press and release the #4 preset control.
Entertainment Systems 7. ON/OFF/Volume/Bal: Turn outer ring of the control to the right to turn the system ON. Once ON, turn to the right to increase the volume, turn to the left to decrease the volume. To turn the system OFF, turn the control fully to the left until the display turns off. For Balance adjustment, pull the control out and turn to the left/right to shift the sound between the left and right speakers. After adjustment, push the control back to the original position. 8.
Entertainment Systems CD/CD PLAYER CARE Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Insert more than one disc into the CD player. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only.
Climate Controls Climate Controls MANUAL A/C SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes air through the instrument panel vents. : Distributes air through the instrument panel vents and the floor vents.
Climate Controls 5. Recirculated air: Used to select fresh or recirculated air operation. May also help reduce undesired outside odors from reaching the interior of the vehicle. Press and hold down briefly to engage/disengage. To reduce humidity inside the vehicle, turn recirculation off. Note: The indicator light will be on when in recirculate mode, and will reduce the amount of time to cool down the interior of the vehicle with A/C.
Lights Lights HEADLAMP CONTROL Pull the control rearward once to turn on your parking lamps. Push it forward to turn on your headlamps. To turn the headlamps and parking lamps off, put the control in the center detent. Foglamp control The fog lamps can only be turned on when the headlamp control is in the parking lamp or headlamp position. Press the foglamp control forward to activate the fog lamps. When the highbeams are activated, the fog lamps will not operate.
Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push the control forward to brighten. • Pull the control back to dim. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal.
Lights BULBS Replacing exterior bulbs Check the operation of all of the bulbs periodically. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to ensure lamp performance, light brightness, pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Driver Controls Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Move the lever down for a single wipe. For intermittent operation, move control up one position and adjust the rotary control to the desired speed. For normal operation, move control up two positions. For high speed operation, move control up three positions. Mist function: To mist, push and release the windshield washer control quickly. The wipers will cycle two or three times to clear the windshield.
Driver Controls 5. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element. TILT STEERING COLUMN Pull the locking lever down to tilt and telescope the steering column to the desired orientation. Return the lever to its original position to secure the wheel. Never adjust the steering wheel when the vehicle is moving.
Driver Controls POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.
Driver Controls Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in-vehicle communications systems, telematics devices and portable two-way radios. A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.
Locks and Security Locks and Security KEYS The key operates all locks on your vehicle. You should always carry a second key with you in a safe place in case you require it in an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer. POWER DOOR LOCKS The power door lock controls are located on the driver and front passenger door panels.
Locks and Security To deactivate/reactivate the autolock feature using the power door unlock control You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. Note: The default setting for the autolock feature is “disabled.” 1. Turn the ignition to the 3 (ON) position. Note: Both vehicle doors must be closed during the activation/deactivation procedure. 2. Press the power door unlock control three times. 3.
Locks and Security Your vehicle has an all-door remote entry system. The all-door remote entry system allows you to: • lock or unlock both vehicle doors without a key. • arm and disarm the anti-theft system. For more information on the anti-theft system, refer to SecuriLock娂 Passive Anti-theft System in this chapter. • open the luggage compartment without a key. • activate the panic alarm.
Locks and Security This process will also activate the vehicle’s anti-theft system. For more information on arming the anti-theft system, refer to SecuriLock娂 Passive Anti-theft System in this chapter. Opening the luggage compartment Press once to open the luggage compartment. Note: This feature is inoperative with the ignition in the 1 (OFF/LOCK) position. • The luggage compartment can be released using the remote entry transmitter.
Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together.
Locks and Security To reprogram the remote entry transmitters: 1. Close both doors and fasten the driver’s seat belt to ensure conflicting chimes do not sound during the procedure. 2. Put the key in the ignition. 3. Turn the key from the 1 (OFF/LOCK) position to the 3 (ON) position. 4. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) and the 3 (ON) position. Note: The eighth turn must end in the 3 (ON) position. 5. Within 20 seconds press any button on the remote entry transmitter.
Locks and Security Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine.
Locks and Security 1. Insert a previously programmed coded key into the ignition. 2. Turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position. Keep the ignition in the 3 (ON) position for at least one second, but no more than 10 seconds. 3. Turn the ignition to the 1 (OFF/LOCK) position. 4. Remove the previously programmed coded key from the ignition. 5. Within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition. 6.
Locks and Security PERIMETER ALARM SYSTEM The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership to aid in troubleshooting. Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the park/turn lamps and will sound the horn.
Locks and Security ELECTRIC DOOR RELEASE To open the door, unlock (with the remote entry transmitter) and push the release button on the door. Note: The vehicle doors may be unlocked by using the remote entry transmitter, however, in the event of a low battery charge, the driver’s door can be manually unlocked and opened by inserting the key into the door lock cylinder and turning counterclockwise.
Seating and Safety Restraints Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and Safety Restraints Rotate the control to adjust seatback. SAFETY RESTRAINTS Safety restraints precautions To maximize restraint system effectiveness, the driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the vehicle is moving. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Seating and Safety Restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder.
Seating and Safety Restraints • This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest. The safety restraints in the vehicle are combination lap and shoulder belts. The safety belts have two types of locking modes described below.
Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Ford Motor Company recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision.
Seating and Safety Restraints Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions. The safety belt pretensioner is a device which removes excess webbing from the safety belt system. The safety belt pretensioner uses the same crash sensor system as the front air bag supplemental restraint system (SRS). When the safety belt pretensioner deploys, webbing from the lap and shoulder belt is tightened.
Seating and Safety Restraints BeltMinder姟 The BeltMinder娂 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. If... The driver’s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off and the vehicle speed is over about 4 mph (7 km/h)...
Seating and Safety Restraints Reasons given... “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an air bag” “I’d rather be thrown clear” Consider... We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the seatback which should be as upright as possible; this can improve comfort. Prime time for an accident.
Seating and Safety Restraints One time disable Any time the driver’s safety belt is buckled and then unbuckled during an ignition ON cycle, the BeltMinder娂 will be disabled for that ignition cycle only. Deactivating/activating the BeltMinder姟 feature Read Steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Seating and Safety Restraints 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable BeltMinder娂 if it is currently enabled, or enable BeltMinder娂 if it is currently disabled. 7. Confirmation of disabling BeltMinder娂 is provided by the safety belt warning light flashing four times per second for three seconds. 8.
Seating and Safety Restraints collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Seating and Safety Restraints National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm) between an occupant’s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably.
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the air bag sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not sufficient enough to cause activation.
Seating and Safety Restraints • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system wiring (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Several air bag system components get hot after inflation. Do not touch them after inflation.
Seating and Safety Restraints Passenger front air bag ON/OFF switch An air bag ON/OFF switch has been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings. Failure to put the switch in a proper position can increase the risk of serious injury or death in a collision. Turning the passenger front air bag off 1.
Seating and Safety Restraints Turning the front passenger air bags back on The front passenger air bag remains OFF until you turn them back ON. 1. Insert the ignition key and turn the switch to ON. 2. The OFF light will briefly illuminate and then shut off when the ignition is turned to ON. This indicates that the passenger front air bag is operational.
Seating and Safety Restraints occupant is not properly buckled up. The most effective way to reduce the risk of unnecessary air bag injuries, without reducing the overall safety of the vehicle, is to make sure all occupants are properly restrained in the vehicle, especially in the front seat. This provides the protection of safety belts and permits the air bags to provide the additional protection they were designed to provide.
Seating and Safety Restraints This vehicle has special energy management safety belts for the driver and right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision. The energy management safety belt is designed to give or release additional belt webbing in some accidents to reduce concentration of force on an occupant’s chest and reduce the risk of certain bone fractures and injuries to underlying organs.
Seating and Safety Restraints Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.
Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are back
Seating and Safety Restraints Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). The shoulder belt should cross the chest, resting snugly on the center of the shoulder. The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Seating and Safety Restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back and turn the passenger air bags OFF. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2.
Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the passenger seat cushion. 2. Locate the tether anchor located behind the passenger seat. 3.
Seating and Safety Restraints 5. Clip the tether to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Seating and Safety Restraints A LATCH system for child seat installation has been provided in your vehicle at the following location: The lower anchors for child seat installation are located at the rear section of the passenger seat between the cushion and seat back. The seat back must be in the full rear position to access the LATCH anchors. To attach a child seat to the lower anchors, place the vehicle seat in the full rear position and the seatback in upright position.
Tires, Wheels and Loading Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Tires, Wheels and Loading The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tires, Wheels and Loading • Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure.
Tires, Wheels and Loading Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced.
Tires, Wheels and Loading higher than the manufacturer’s recommended cold inflation pressure which can be found on either the tire label or certification label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the tire label or certification label. When weather temperature changes occur, tire inflation pressures also change.
Tires, Wheels and Loading TIRE REPLACEMENT REQUIREMENTS Your vehicle is equipped with tires designed to provide a safe ride and handling capability. Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford.
Tires, Wheels and Loading Tire inflation kit Your vehicle is equipped with an emergency tire inflation kit (located in the luggage compartment). The inflation kit consists of an air compressor to reinflate the tire and a sealing compound that will effectively seal most punctures caused by nails or similar objects. This kit will provide a temporary seal allowing you to drive your vehicle up to 120 miles at a maximum speed of 50 mph. Note: The inflation kit is to be used for one tire only.
Tires, Wheels and Loading • Drive carefully and avoid abrupt steering maneuvers. • Periodically monitor tire inflation pressure in the affected tire; if the tire is losing pressure, have the vehicle towed. • Read the information in the Tips for use of the tire inflation kit section to ensure safe operation of the tire inflation kit and your vehicle.
Tires, Wheels and Loading What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stages with the tire inflation kit: • In the first stage, the tire will be reinflated with a sealing compound and air. After the tire has been reinflated, you will need to drive the vehicle a short distance (approximately two miles) to activate the sealing compound inside the tire.
Tires, Wheels and Loading 4. Loosen the safety latch (4) on the sealing compound container (5) and rotate the container until it is upright and clicks into place. 5. Peel the speed limit sticker (6) off the side of the container and affix it to the center of the steering wheel or the instrument panel so it can be seen in plain view. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) to prevent the vehicle’s battery from draining.
Tires, Wheels and Loading Note: When the sealing compound is first added into the tire, the air pressure gauge reading (7) on the compressor unit may increase up to 90 psi; this is normal and should be no reason for concern. The pressure will drop after about 30 seconds of operation. Do not stand next to the damaged tire while it is inflating.
Tires, Wheels and Loading Second stage: Checking tire pressure 1. Stop driving after approximately two miles. Refer to the Tips for use of the tire inflation kit for safe operation of the tire inflation kit. Then check the air pressure of the damaged tire as follows: • Ensure the compressor is turned off by pressing the “O” side of the orange button. • Remove the hose and the cable with the electrical plug from the kit’s storage compartment.
Tires, Wheels and Loading Note: Before driving any further, adjust the tire pressure to the recommended pressure. 3. Turn the air compressor off by pressing the “O” side of the orange button, then unscrew the hose from the tire’s air valve, reinstall the tire valve cap, unplug the electrical plug from the power point and stow the inflation kit in its proper place.
Tires, Wheels and Loading Note: If you experience any unusual vibration, ride disturbance or noise while driving, reduce your speed until you can safely pull off to the side of the road to call for roadside assistance. You can check the tire pressure any time within the 120 miles by performing the following: 1. Ensure the compressor is turned off by pressing the “O” side of the orange button. 2. Remove the hose and the cable with the electrical plug from the kit’s storage compartment. 3.
Tires, Wheels and Loading INFORMATION CONTAINED ON THE TIRE SIDEWALL Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating.
Tires, Wheels and Loading 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h).
Tires, Wheels and Loading 10. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. 11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading the road in adverse (wet, snowy, etc.) conditions. Visually check your tires for uneven wear, looking for high and low areas or unusually smooth areas. Also check for signs of tire damage. When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to prevent your vehicle from skidding and hydroplaning.
Tires, Wheels and Loading Tires Your Ford GT is equipped with low profile, high performance tires that are designed to optimize handling, steering and braking. These tires are not designed for off-road or winter performance, and their ride, noise and wear characteristics are different than other tires. Also, because of their lower profile, the tires are more susceptible to damage due to potholes and rough or unpaved roads.
Tires, Wheels and Loading Wheels Your Ford GT is equipped with unique wheels matched to the tires. These wheels are more susceptible to damage due to their diameter, width and low profile tires. To avoid damage to your wheels: • Maintain proper tire pressure (see “Tires” previously listed). • When installing wheels, always torque lug nuts to specification with a torque wrench. • Inspect your wheels for damage on a regular basis. If a wheel is damaged, replace it immediately.
Tires, Wheels and Loading Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by a qualified technician at a Ford or Lincoln/Mercury dealer. Front wheel drive (FWD) vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear.
Tires, Wheels and Loading SNOW TIRES The original equipment tires on your Ford GT are designed for maximum performance in dry and wet conditions. They are not designed for winter use on ice or snow and cannot be used with snow chains or other tire mounted traction aid devices. TRAILER TOWING Your vehicle is not equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers.
Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door. Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload. The payload listed on the tire label is the maximum payload for the vehicle as built by the assembly plant.
Tires, Wheels and Loading Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Tires, Wheels and Loading Exceeding the Safety Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations.
Tires, Wheels and Loading The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • An example for your vehicle with 1400 lb. (636 kg) of cargo and luggage capacity. You decide to go golfing. You and your friends average 220 lb. (100 kg) each and the golf bags weigh approximately 30 lb. (14 kg) each.
Driving Driving STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all electrical accessories except the audio system and power windows, which retain power for 10 minutes or until the door is ajar. This position also locks the steering wheel and allows key removal. 2. ACC, allows electrical accessories to operate while the engine is not running. 3. ON, all electrical circuits are operational and warning lights are illuminated. Key position when driving.
Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Before starting the vehicle: 1. Make sure all occupants buckle their safety belts.
Driving 5. Turn the key to 3 (ON). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. Cold weather starting/operating tips Due to the high-performance design of this vehicle, certain precautions should be taken when starting and operating the vehicle at temperatures below 0°F (-18°C): 1. Ensure battery is fully charged. 2.
Driving Starting the engine 1. Turn the key to 3 (ON). 2. Press the red START ENGINE button on the instrument panel, then release the button as soon as the engine starts. Excessive cranking could damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to 1 (OFF/LOCK), wait 10 seconds and try again.
Driving BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by a qualified service technician. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by a qualified service technician. Refer to Brake system warning light in the Instrument Cluster ! chapter for information on the brake BRAKE system warning light.
Driving Parking brake To set the parking brake, pull the parking brake handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. ! BRAKE To release, press and hold the button, pull the handle up slightly, then push the handle down. Always set the parking brake fully and make sure that the gearshift is securely latched in 1 (First).
Driving STEERING To prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). Refer to Checking and adding power steering power fluid in the Maintenance and Specifications chapter for information on checking and filling the power steering fluid reservoir.
Driving MANUAL TRANSMISSION OPERATION Using the clutch The manual transmission has a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in the neutral position. 3. Start the engine, then press the brake pedal and release the parking brake. 4.
Driving Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1-2 15 mph (24 km/h) 2-3 25 mph (40 km/h) 3-4 40 mph (64 km/h) 4-5 45 mph (72 km/h) 5-6 50 mph (80 km/h) Reverse 1. Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. 2. Move the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse). 3.
Driving Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. GROUND CLEARANCE Note: Because of low vehicle ground clearance, use caution when approaching curbs/curb stops from front and rear — vehicle damage could occur.
Roadside Emergencies Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Roadside Emergencies This switch has a red reset button on top of it and is located in the front passenger’s footwell, behind an access panel and to the left of the fuse panel. To access the switch, roll back the floor mat and unscrew the four release pins on the panel. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition ON. 5. Wait a few seconds and return the key to OFF. 6.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A Grey Violet Pink Tan Brown Red Blue Yellow Natural Green — — — — — Grey Violet Pink Tan Brown Red Blue Yellow Natural Green — — — — — — — — — — — — Yellow — Green Orange Red Blue Tan Natural Passenger compartment fuse panel The fuse panel is located in the passenger footwell, behind an access panel.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 Fuse Amp Rating — — 15A* 4 10A* 5 2A* 6 10A* 7 5A* Passenger Compartment Fuse Panel Description Not used Not used Front and rear park lamps, License plate lamps, Side markers Ignition switch, Start relay, Cluster start signal, Start cut-out relay Powertrain Control Module (PCM) relay coil, Injector relay coil Center High-Mounted Stop Lamp (CHMSL), Stop lamps Climate control module (if equipped), EPATS module 109 2006
Roadside Emergencies Fuse/Relay Location 8 Fuse Amp Rating 15A* 9 20A** 10 5A* 11 12 13 14 15 16 17 18 — 5A* — — 30A** 5A* 15A* 15A* 19 20 21 22 — 15A* 5A* 5A* 23 24 25 26 27 28 — — 20A* 5A* 5A* 10A* 29 30 31 32 10A* — — 10A* 110 2006 GT (gto) Owners Guide (post-2002-fmt) USA_English (fus) Passenger Compartment Fuse Panel Description Door ajar indicator, Headlamp indicator, Cluster, Radio, OBD II, Mirrors Power door lock motors, Electronic door latch motors Rear defroster switch indicator li
Roadside Emergencies Fuse/Relay Location 33 Fuse Amp Rating 15A* 34 5A* 35 — * Mini fuse ** Cartridge fuse Passenger Compartment Fuse Panel Description Restraint Control Module (RSM), Passenger Air bag Deactivation (PAD) indicator lamp, ACS switch Anti-lock Brake System (ABS) Run/Acc Input Not used Power distribution box The power distribution box is located in the front compartment.
Roadside Emergencies The high-current fuses are coded as follows.
Roadside Emergencies Fuse/Relay Location 13 Fuse Amp Rating 30A** 14 15 16 17 18 19 20 30A** 20A* 5A* 25A* 25A* 20A* 20A* 21 22 23 24 25 26 27 28 29 10A* 20A* Full ISO relay Full ISO relay Full ISO relay Full ISO relay 20A* 15A* 15A* 1⁄2 ISO relay 30 1⁄2 ISO relay 31 1⁄2 ISO relay 32 * Mini fuse **Cartridge fuse Power Distribution Box Description Primary Fuel Pump Delivery Module (FPDM), Secondary Fuel Pump Delivery Module (FPDM) Intercooler pump Alternator field circuit EEC keep alive power Lighting
Roadside Emergencies Auxiliary relay box The relay box is located in the front of the vehicle under the hood.
Roadside Emergencies Fuse/Relay location 10 11 12 * Mini fuse Fuse amp Auxiliary Relay Box Description rating Micro relay High speed wiper Micro relay Intermittent wiper Micro relay Wiper stop relay JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Roadside Emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to the negative (-) battery terminal of the stalled vehicle. 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2.
Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the negative (-) battery terminal of the stalled vehicle. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING Note: Do not attempt to tow this vehicle from the rear. Ford Motor Company has not approved towing this vehicle from the rear. Note: It is recommended that the Ford GT be towed with flatbed equipment only. Do not tow with a slingbelt or wheel lift. Ford Motor Company has not approved a slingbelt or wheel lift towing procedure. If the vehicle is towed by other means or incorrectly, vehicle damage may occur.
Roadside Emergencies TRANSPORTATION INSTRUCTIONS 1. Tow hook 2. 60 inches (152 cm) 3. 36 inches (91 cm) 4. Stacked 4x4 5. Flatbed 6. 7.5° maximum 7. Tow line Use the following procedure to transport your vehicle: 1. Install the tow hook. (Located in luggage compartment). Refer to Tow hook later in this chapter. 2. Stack one long and one short 4x4 wood block per side (used to extend the flatbed deck length). 3. Lower the flatbed deck to hold the wood blocks in place.
Roadside Emergencies 5. Transport the vehicle with the parking brake OFF and the transmission in NEUTRAL. 6. Secure the vehicle with wheel basket tie-downs to the flatbed deck. Note: Inspect tie-downs periodically for tightness. Never fasten J-hooks to any suspension wheel or driveline component because J-hooks will damage these components. Note: If you have this vehicle transported by either air, water, or rail, follow the wheel tie-down procedure starting with Step 5.
Customer Assistance Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer for warranty repairs. While any Ford dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Customer Assistance Additional Assistance If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.). In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Customer Assistance THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Customer Assistance Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer Assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer Assistance impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.
Customer Assistance If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Worldwide Direct Market Operations.
Customer Assistance applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3.
Cleaning Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Do not drive your vehicle through an automated, commercial car wash due to the vehicle’s low ground clearance, tire width and track. Wash your vehicle by hand, with a commercial wand, or by using a touchless commercial wash with no mechanical tracks on the floor.
Cleaning • Do not let excess water drain into the engine air intakes located on the engine cover. WAXING Applying a polymer paint sealant to your vehicle every six months will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area.
Cleaning ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft Wheel and Tire Cleaner (ZC-37–A), which is available from your dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water. • Never apply any cleaning chemical to hot or warm wheel rims or covers.
Cleaning 5.4L DOHC Supercharged V8 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42).
Cleaning hot wax treatments used by commercial car washes, tree sap, or other organic contamination. To clean these items, please follow these tips: • The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23), available from your dealer. • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts.
Cleaning Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. LEATHER SEATS Your vehicle is equipped with seating covered in premium, top-grain Frau威 leather which is extremely durable, but still requires special care and maintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintain the appearance of the leather. Failure to care for the leather can result in drying out and fading of the material.
Cleaning UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Maintenance and Specifications Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered.
Maintenance and Specifications OPENING ENGINE COMPARTMENT 1. Inside the vehicle, pull the decklid release handle located on the roof panel between the driver and passenger seats. Note: Do not operate the decklid release while the vehicle is in motion. 2. Lift up on the decklid at the side air scoop area to provide better access to the auxiliary release.
Maintenance and Specifications 3. While pushing down slightly on the decklid, push in on the auxiliary release located at the rear of the passenger compartment behind the driver’s side seat area. 4. Go to the other side of the vehicle and release the right side auxiliary latch located behind the passenger seat area. Note: make sure not to relatch the driver’s side. 5. Lift the decklid and ensure that it is secure.
Maintenance and Specifications CLOSING THE ENGINE COMPARTMENT 1. Pull the decklid downward to the secondary latch position. Push down on the center of the decklid firmly to close. 2. Ensure that both latches are engaged. Both latches need to be fully latched. If one or both are not fully latched a chime will sound and the “Door Ajar” warning lamp will illuminate. OPENING THE LUGGAGE COMPARTMENT 1. Push the button on remote entry transmitter (see Remote Entry System in the Locks and Security chapter).
Maintenance and Specifications REMOVING THE LUGGAGE COMPARTMENT LINER Some components are located under the luggage compartment liner. Follow these steps to remove and install the liner. 1. Open the front compartment. 2. Unlock all four retainers by turning each one a quarter turn in either direction. Leave retainers attached to tray. The tire inflation kit can be left in place or removed during tray removal. 3. Remove the tray by lifting it up from the middle. It may be necessary to tilt up to remove.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 4V DOHC Supercharged V8 engine 1. Power steering fluid reservoir 2. Engine oil dipstick 3.
Maintenance and Specifications 4. Engine oil filter 5. Engine coolant reservoir 6. Intercooler coolant reservoir 7.
Maintenance and Specifications 8. Battery 9. Brake fluid reservoir 10. Clutch fluid reservoir 11.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. Standard fill amount is 1 quart (0.9 L). Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Maintenance and Specifications 4. Open the engine compartment cover. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. Check oil level within 1 minute of shutting off the vehicle. • If the oil level is between the MIN—MAX marks, the oil level is acceptable. DO NOT ADD OIL.
Maintenance and Specifications Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4.
Maintenance and Specifications BATTERY If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.
Maintenance and Specifications Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. RN LE TU AD RE Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1.
Maintenance and Specifications ENGINE COOLANT Checking engine/intercooler coolant The concentration and level of engine/intercooler coolant should be checked at the mileage intervals listed in the Scheduled Maintenance Guide. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060).
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoirs. • The engine coolant level should be maintained at the bottom of the lower baffle in the coolant reservoir and the bottom of the upper baffle in the intercooler reservoir (or to the sight windows, if equipped). • Refer to the Scheduled Maintenance Guide chapter for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Speciality Orange Engine Coolant, VC-2 (US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant.
Maintenance and Specifications 6. Replace the cap. Turn until clicking sound is heard. (Cap must be tightly installed to prevent coolant loss.) After any coolant has been added, check the coolant concentration, refer to Checking engine coolant. If the concentration is not 50/50 (protection to –34° F/–36° C), drain some coolant and adjust the concentration. It may take several drains and additions to obtain a 50/50 coolant concentration.
Maintenance and Specifications • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months. If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%.
Maintenance and Specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and Specifications Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position. Fuel filler door Your fuel tank filler is located on the passenger side fender.
Maintenance and Specifications deteriorate more rapidly. In Canada, premium grade fuel generally contains more metallic additives than regular fuel. We recommend using regular grade fuel. In Canada, many fuels contain metallic additives, but fuels free of such additives may be available; check with your local fuel dealer. Do not use fuel containing methanol. It can damage critical fuel system components.
Maintenance and Specifications Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Your Service engine soon indicator may come on.
Maintenance and Specifications amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range.
Maintenance and Specifications Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy. In general, lower temperatures give lower fuel economy.
Maintenance and Specifications Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy.
Maintenance and Specifications • Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule. The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system.
Maintenance and Specifications detected a malfunction. Temporary malfunctions may cause your Check engine/Service engine soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel.
Maintenance and Specifications 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.
Maintenance and Specifications Use only a DOT 3 brake fluid designed to meet Ford specification ESA-M6C25–A. Refer to Lubricant specifications in this chapter. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. If taken internally, drink water and induce vomiting. Seek medical attention immediately. Refer to Removing Luggage Compartment Liner in this chapter to gain access to the clutch fluid reservoir. 1.
Maintenance and Specifications MOTORCRAFT PART NUMBERS Component Air filter element (2) Fuel filter Oil filter PCV valve Spark plugs 1 5.4L DOHC Supercharged V8 FA-1682 FG-1091 FL-2023 1 2 The PCV valve is a critical emission component. It is one of the items listed in the Scheduled Maintenance Guide chapter and is essential to the life and performance of your vehicle and to its emissions system. For PCV valve replacement, see your dealer or a qualified service technician.
Maintenance and Specifications REFILL CAPACITIES Fluid Brake fluid and clutch fluid Ford Part Name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid 1 Motorcraft Engine coolant Premium Gold Engine Coolant (yellow-colored) Intercooler coolant Motorcraft Premium Gold Engine Coolant (yellow-colored) Engine oil Motorcraft SAE (includes filter 5W-50 Full change) Synthetic Motor Oil Fuel tank N/A Application All Capacity Fill to line on reservoir All 6.6 gallons (25L) All 4.
Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Brake/Clutch fluid Ford part name Ford part number Motorcraft High PM-1 Performance DOT 3 Motor Vehicle Brake Fluid Silicone Lubricant XL-6 Door weatherstrips Door latch, hood Multi-Purpose latch, auxiliary Grease hood latch, door hinges, striker plates, seat tracks and fuel filler door hinge Engine coolant Motorcraft Premium Gold Engine Coolant (yellow-colored) Engine oil Motorcraft SAE 5W-50 Full Synthetic Motor Oil Lock cylinders Penetrating
Maintenance and Specifications ENGINE DATA Engine Displacement (cubic inches) Required fuel Firing order Spark plug gap Ignition system Compression ratio 5.4L DOHC Supercharged V8 engine 330 91 octane 1-3-7-2-6-5-4-8 1.1–1.2mm (0.042–0.046 inch) Coil on plug 8.4:1 VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Tread - Front (5) Tread - Rear Inches (mm) 182.8 (4644) 76.9 (1952.5) 44.3 (1124.8) 106.7 (2709.9) 63.0 (1599.4) 63.6 (1617.
Maintenance and Specifications 3 5 2 172 2006 GT (gto) Owners Guide (post-2002-fmt) USA_English (fus)
Maintenance and Specifications 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission.
Accessories Accessories GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems — such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
Scheduled Maintenance Guide Scheduled Maintenance Guide GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Scheduled Maintenance Guide vehicle manufacturers, dealers and other persons engaged in the business of repairing, servicing, selling, leasing or trading motor vehicles as well as fleet operations from knowingly removing or rendering an emissions control system inoperative after sale and delivery to an ultimate purchaser. In Canada, modifications of the emissions control system could create liability under applicable federal or provincial laws.
Scheduled Maintenance Guide WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated. Service information and supporting specifications are provided in this Owner’s Guide.
Scheduled Maintenance Guide Multi-point Inspection In order to keep your vehicle running right, it is important that you have the systems on your vehicle checked regularly. This can help identify any potential issue before there are any problems. Ford Motor Company suggests the following multi-point inspection to be performed at every scheduled maintenance as the way to ensure your vehicle keeps running right.
Scheduled Maintenance Guide ADDITIONAL INFORMATION AVAILABLE ON THE WEB To learn more about the importance of routine and dealer-performed maintenance on your vehicle, please visit the Ford Customer Service website. You’ll also find important warranty information, customer assistance, technical expertise, frequently asked questions and much more. The website location is: www.ford.com. Then go to the vehicles and service pick at the web site.
Miles (x 1000) Km (x 1000) Change engine oil and replace oil filter Inspect tires for wear, measure tread depth and rotate Multi–point inspection Inspect steering linkage, suspension and ball joints Inspect engine cooling system and hoses Inspect brake pads, shoes, rotors, drums, brake lines and hoses Adjust parking brake Inspect half-shaft boots Inspect exhaust system and heat shields Inspect drive belts Replace fuel filter Replace sump drive belt Inspect engine air filter Replace engine air filter Change
Miles (x 1000) Km (x 1000) Change engine oil and replace oil filter Inspect tires for wear, measure tread depth and rotate Multi–point inspection Inspect steering linkage, suspension and ball joints Inspect engine cooling system and hoses Inspect brake pads, shoes, rotors, drums, brake lines and hoses Adjust parking brake Inspect half-shaft boots Inspect exhaust system and heat shields Inspect drive belts Replace fuel filter Replace sump drive belt Inspect engine air filter Replace engine air filter Change
Miles (x 1000) Km (x 1000) Change engine oil and replace oil filter Inspect tires for wear, measure tread depth and rotate Multi–point inspection Inspect steering linkage, suspension and ball joints Inspect engine cooling system and hoses Inspect brake pads, shoes, rotors, drums, brake lines and hoses Adjust parking brake Inspect half-shaft boots Inspect exhaust system and heat shields Inspect drive belts Replace fuel filter Replace sump drive belt Inspect engine air filter Replace engine air filter Change
Scheduled Maintenance Guide Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.
Scheduled Maintenance Guide Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.
Scheduled Maintenance Guide Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.
Scheduled Maintenance Guide Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.
Scheduled Maintenance Guide Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.# Date: Dealer’s Stamp: Odometer reading: R.O.
Scheduled Maintenance Guide PREMIUM GOLD ENGINE COOLANT Change Motorcraft Premium Gold Engine Coolant at three years or 30,000 miles (48,000 km), whichever comes first and every three years or 30,000 miles (48,000 km) thereafter.
Scheduled Maintenance Guide OIL PUMP DRIVE BELT Change the engine oil pump drive belt if your vehicle has been stored for an extended period of time (three years or more) without the engine being operated for at least 30 minutes per year.
Index Index A Air bag supplemental restraint system ..........................................48 and child safety seats ..............49 description ................................48 disposal ......................................55 driver air bag ............................50 indicator light ...........................51 operation ...................................50 passenger air bag .....................50 passenger deactivation switch ........................................52 Air cleaner filter ...
Index Customer Assistance ................105 Ford accessories for your vehicle .....................................138 Ford Extended Service Plan ..........................................125 Getting assistance outside the U.S. and Canada ..............129 Getting roadside assistance ...105 Getting the service you need .........................................123 Ordering additional owner’s literature .................................130 The Dispute Settlement Board .......................................
Index G Gas cap (see Fuel cap) ............158 Gas mileage (see Fuel economy) .................160 Gauges .........................................12 H Hazard flashers .........................106 Headlamps ...................................21 aiming ........................................22 bulb specifications ....................23 flash to pass ..............................21 high beam .................................21 replacing bulbs .........................23 turning on and off ..................
Index O Octane rating ............................159 Oil (see Engine oil) ..................147 P Parking brake ............................100 Parts (see Motorcraft parts) ....168 Power distribution box (see Fuses) ...............................111 Power mirrors .............................26 Power point .................................25 Power steering ..........................101 fluid, checking and adding ....165 fluid, refill capacity ................169 fluid, specifications .........
Index T Turn signal ..................................22 Tilt steering wheel ......................25 Tires .......................................66–67 alignment ..................................87 care ............................................84 checking the pressure ..............69 inspecting and inflating ...........68 label ...........................................84 replacing ....................................71 rotating ......................................88 sidewall information ........
