Table of Contents Introduction Instrument Cluster 4 10 Warning lights and chimes Gauges 10 16 Entertainment Systems 19 AM/FM AM/FM AM/FM AM/FM stereo stereo with CD stereo cassette with CD stereo with in-dash six CD Climate Controls Manual heating and air conditioning Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 19 21 24 27 35 35 44 45 45 49
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving 113 113 138 153 167 182 182 184 197 202 208 212 213 Starting Brakes Transmission operation 213 216 221 Roadside Emergencies 227 Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Lug nut tor
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine coolant Fuel information Air filter(s) Part numbers Maintenance product specifications and capacities Engine data 268 270 272 275 278 283 297 302 303 305 Accessories 308 Index 310 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag.
Introduction To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX
Instrument Cluster WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Instrument Cluster Check engine: The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the ⬙Check engine⬙ light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the ⬙Check engine⬙ light blinks eight times, it means that the vehicle is not ready for I/M testing.
Instrument Cluster Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your authorized dealer. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.
Instrument Cluster Engine coolant temperature: Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter. Never remove the coolant reservoir cap while the engine is running or hot. Traction Control娂 or AdvanceTrac威 active (if equipped): Illuminates when the Traction Control娂 is active, refer to the Driving chapter for more information.
Instrument Cluster Speed control: Illuminates when the speed control is engaged. Turns off when the speed control system is disengaged. Low washer fluid: Illuminates when the windshield washer fluid is low. • Without Message Center • With Message Center Door ajar: Illuminates when the ignition is in the ON position and any door is open. • Without Message Center • With Message Center Displays which door or the liftgate is open.
Instrument Cluster Bulb warning: Illuminates when one of the exterior front turn lamps or rear brake/turn/tail lamps bulb has burned out. • Without Message Center • With Message Center Displays which bulb is burned out. Depress the RESET control to clear. High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened.
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot.
Instrument Cluster Odometer: Registers the total miles (kilometers) of the vehicle. • Without Message Center To switch the display from Metric to English, press and hold the button on the cluster for three seconds. The temperature display in the overhead console (if equipped) will also be changed. • With Message Center Refer to Message Center in the Driver Controls chapter on how to switch the display from Metric to English. Trip odometer: Registers the miles (kilometers) of individual journeys.
Instrument Cluster Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The arrow near the fuel pump icon indicates which side of the vehicle the fuel filler door is located.
Entertainment Systems AUDIO SYSTEMS AM/FM stereo system (if equipped) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Audio: Press to access select various settings. / Treble: Press to adjust the treble setting. Use Bass: Press to adjust the bass setting. Use / / / SEEK SEEK . . Balance: Press to adjust the audio between the left and right speakers. / / SEEK .
Entertainment Systems 3. Seek: Press to access the next/previous strong station or track. 4. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 5. AM/FM: Press to select AM/FM frequency band. 6. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume.
Entertainment Systems AM/FM stereo/ single CD sound system (if equipped) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press / / SEEK to set. MENU to access.
Entertainment Systems Treble: Press to adjust the treble setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Press MENU to access and use / / SEEK to adjust. The recommended level is 1–3.
Entertainment Systems 10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. 14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16.
Entertainment Systems AM/FM stereo cassette/single CD sound system (if equipped) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Seek: Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 4. Menu: Press to toggle through the following modes: Treble: Press to adjust the treble setting. Use / / SEEK . / / SEEK .
Entertainment Systems Fade: Press to adjust the audio between the front and rear speakers. / / SEEK . Use Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind / / SEEK to adjust. noise. Press MENU to access and use The recommended level is 1–3. Level 0 (SPEED OFF) turns the feature off and level 7 is the maximum setting Setting the clock: Press MENU until HOURS SET or MINUTES SET is / / SEEK to adjust the hours/minutes.
Entertainment Systems 9. Compress (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 10. Repeat: Press to repeat the current CD track. 11. Fast forward: Press to manually advance in a CD track or cassette. 12. Rewind: Press to manually reverse in a CD track or cassette. 13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 14. Tape: Insert a tape facing to the right.
Entertainment Systems 19. CD eject: Press to eject a CD. 20. CD slot: Insert a CD label side up. 21. Seek:Press to access the previous strong station or track. 22. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. When this radio is used in cargo vans where no rear speakers are installed in the vehicle, fading to the rear speakers will result in no audio output.
Entertainment Systems 1. / Tuner: Press to manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: / Treble: Press to adjust the treble setting. Use Bass: Press to adjust the bass setting. Use / / / SEEK SEEK . . Balance: Press to adjust the audio between the left and right speakers. / / SEEK .
Entertainment Systems 4. Aux: Press to toggle between FES/DVD and AUX modes. If no auxiliary sources are available, NO AUX AUDIO will be displayed. 5. Seek: Press to access the next strong station or track. 6. Text: In CD mode, press to display the track name, artist name and disc name (if available). 7. Shuffle: Press to play tracks in random order. 8. Comp (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 9.
Entertainment Systems 16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 17. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last. 18. LOAD: Press to load a CD, then select a slot number using the radio presets 1 through 6.
Entertainment Systems 1. Volume: Press to / increase/decrease volume control. 2. Media: Press to select from different playing medias. / : Press to activate dual 3. play mode and enable the rear seat passengers to hear audio through the headphones. Press again to deactivate. 4. MEM: Press consecutively to scroll through the preset stations, change tape side (if equipped), or to change discs on multiple disc radios (if equipped). / to access the next/previous strong radio station, 5.
Entertainment Systems Dual play mode / on the rear seat audio Press controls or simultaneously press the radio preset controls 2 and 4 to enable/disable dual play. During dual play, the rear vehicle speakers will be deactivated and the wired headphones (if equipped) will become active. Two different medias can be played in the vehicle simultaneously: • The driver can select a media from the main radio face (radio, tape, CD or DVD if equipped) and listen using the front speakers.
Entertainment Systems Cassette/player care Do: • Tighten very loose tapes by inserting a pen or pencil into the hole and turning the hub. • Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity or cold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation. Don’t: • Use cassettes that are longer than 90 minutes.
Entertainment Systems CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed.
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Temperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to cool the vehicle. This re-cooling of the interior air is more economical and efficient.
Climate Controls Dual zone manual heating and air conditioning system with rear passenger compartment climate control (if equipped) 1. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to cool the vehicle. This re-cooling of the interior air is more economical and efficient.
Climate Controls will be warmer or cooler than the driver airflow temperature setting when more than one rear temperature light ( REAR ) is illuminated. 5. R Rear defroster: Press to activate/deactivate rear window defroster. Refer to Rear window defroster later in this chapter for more information. 6. Recirculated air: Press to activate/deactivate air recirculation in cabin.
Climate Controls In the and modes: • Move the temperature control selector to the coldest setting. • Select A/C and recirculated air colder airflow. . Use with A/C to provide • Set the fan to the highest speed initially, then adjust to maintain passenger comfort. In extremely cold temperatures, to maximize overall heater performance it is suggested to not operate the auxiliary system (if so equipped) until the engine temperature gauge crosses into the normal operating range.
Climate Controls DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control.
Climate Controls 6. Recirculated air: Press to activate/deactivate air recirculation in the vehicle cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculated air can be . Recirculated air engaged manually in any airflow selection except may turn off automatically in all airflow selections. 7. A/C: Press to activate/deactivate air conditioning.
Climate Controls Dual zone automatic temperature control with heated seats and rear passenger compartment climate control (if equipped) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control.
Climate Controls 7. :Distributes air through the windshield defroster vents and the floor vents. 8. : Distributes air through the floor vents. 9. : Distributes air through the instrument panel vents and the floor vents. 10. : Distributes air through the instrument panel vents. 11. Manual override controls: Allows you to change the system operation. To return to full automatic control, press AUTO. 12. Driver heated seat control: Press once to activate the high heat setting (2 indicator lights).
Climate Controls Operating tips • To reduce fog build up on the windshield during humid weather, place position. the air flow selector in the • To reduce humidity build up inside the vehicle: do not drive with the airflow selector in the OFF or with recirculated air engaged. • Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield.
Climate Controls AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: Turn to select the desired fan speed. 2. Temperature/mode selection: The distribution of air from the overhead and floor registers is based on the temperature selected. Turn to select for comfort. To use the rear climate controls, ensure that REAR is pressed on the main climate control face. REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. P Turns the headlamps on. Note: Some vehicles may be equipped with a headlamps on with wipers feature. In order for this feature to work: • the ignition must be in run and the front wipers must be on greater than 10 seconds except during a mist wipe or while the wipers are on to clear washer fluid during a wash condition.
Lights To program the auto lamp exit time delay: 1. Start with the ignition in the OFF position and the headlamp control in the autolamp position. 2. Deselect the auto lamps. 3. Put the ignition in RUN. 4. Put the ignition in OFF. 5. Select the autolamps. • Note: Steps 2 through 5 must be performed within a 10 second period. • At this point, the headlamps and park lamps will turn on. 6. Deselect the auto lamps after the desired auto lamp delay time (maximum of 3 minutes).
Lights Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. Battery saver The battery saver will shut off the exterior lamps and interior lamps, except the hazard warning lamps if activated, 10 minutes after the ignition control has been turned off.
Lights The dome lamp will not illuminate if the control switch is not rotated past the detent. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized dealer. You will need a #2 Phillips screwdriver to make the adjustments. Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.
Lights 5. Locate the vertical adjuster on each headlamp, then use a # 2 Phillips screwdriver to turn the adjuster either counterclockwise (to adjust up) or clockwise (to adjust down) positioning the horizontal edge of the high intensity light on the horizontal reference line. 6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. 7. Close the hood and turn off the lamps. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal.
Lights Map lamps (if equipped) The map lamps and controls are located on the center overhead console. Press the raised portion on each lens to activate the lamps. Second row & third row dome and map lamps (if equipped) The second row dome and map lamps are located overhead, above the second row passenger seats. The dome lamp will stay on if the panel dimmer control is moved to the passenger side position. When the control is in the middle position, the lamp will only come on when a door is opened.
Lights The dome lamp will illuminate whenever a front door is opened. If either front door has been opened from the outside, the lamp will remain on for 20 seconds after the door is shut. If any other door has been opened from the inside, the lamp will shut off immediately after the door is closed. Cargo lamp The cargo lamp will stay on if the control is moved to the driver side position. When the control is in the middle position, the lamp will only come on when a door is opened.
Lights Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Lights Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in the OFF position, then open the hood. 2. Remove the two retainer pins to release the headlamp assembly and pull headlamp assembly forward to expose the back of the bulb. 3. Disconnect the electrical connector from the bulb by pulling rearward and unlock the bulb by rotating it counterclockwise. Handle a halogen headlamp bulb carefully and keep out of children’s reach.
Lights 3. To remove the side marker bulb, turn the bulb socket counterclockwise, and pull the bulb straight out of the socket. 4. To remove the parking/turn bulb, turn the socket on the bottom of the headlamp assembly counterclockwise and pull the bulb straight out of the socket. Install the new bulb(s) in reverse order. Replacing tail lamp/backup/turn lamp bulbs 1.
Lights Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly. 3. Pull the lamp down and twist the bulb socket counterclockwise. Remove the bulb socket from the lamp. 4. Pull out the old bulb and push in the new bulb. 5. Install the bulb socket in the lamp assembly by turning it clockwise. 6.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.
Driver Controls OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Conversation mirror The conversation mirror allows the driver to view the rear seating area. This does not replace the rear view mirror. Electronic compass/temperature display (if equipped) The overhead console may have an electronic compass and outside air temperature display. The compass heading and outside air temperature are displayed together - side by side.
Driver Controls The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass. Zone variation mode 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position. 3 2 1 15 4 14 13 5 12 6 7 8 9 1011 3.
Driver Controls Compass calibration mode 1. Press the momentary push button and hold it for more than 8 seconds. After 8 seconds, CAL is displayed, then release it. Note: After button release CAL will be displayed with a heading. The compass is now de-calibrated and enters the Initial AutoCal Mode. 2. Drive the vehicle in a tight circle in a magnetically clean area such as an open parking lot. Drive at a rate not faster than 15 seconds per circle 5 mph (8km/h).
Driver Controls If the door is allowed to slide open or closed unrestrained, personal injury or damage to the door could result. When closing the sliding door, keep the head, hands and other body parts of vehicle occupants out of the path of the closing door. Slide the door closed in a careful, controlled manner. When closing the sliding doors, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the sliding door openings.
Driver Controls Power Sliding Door (PSD) (if equipped) With this option, you can open and close the sliding door(s) with the following controls inside your vehicle. • overhead console button • remote entry transmitter button • second row passenger control switch • inside and outside release handle Opening and closing the PSD The PSD will operate without the key in the ignition. The transaxle must be in PARK to open the PSD, when the key is in the ignition and turned to the ON position.
Driver Controls To power open or close the PSD from the second row passenger control switch: • Ensure that the PSD is unlocked, using the remote entry transmitter or power door unlock. Refer to Remote Entry System in the Locks and security chapter. • Push and release the right or left hand second row passenger control. The control(s) are located on the trim panel in front of the sliding door.
Driver Controls desirable to prevent power operation of the door by rear seat passengers or if manual operation of the door is desired or necessary when the vehicle is stopped or parked on a steep downhill grade. Refer to the Manual operation of the sliding door section in this chapter for more information. With the child safety lock engaged, the inside handle operation will always be disabled regardless of the position of the Power Door Lockout control.
Driver Controls 8. Remove the PSD fuse (fuse #11) from the passenger fuse panel and leave it out for thirty (30) seconds. Refer to the chapter on Fuses and Relays. Refer to Fuses and relays in the Roadside emergencies chapter. 9. Reinstall the fuse and wait ten (10) seconds. 10. Repeat Steps 1–6 above. If the door still does not operate correctly, see your dealer for service.
Driver Controls CLOCK (IF EQUIPPED) Press the right (+) control to move the time display forwards. Press the left (-) control to move the time display backwards. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
Driver Controls • Located next to the second row seat. • Located on the right trim panel in the rear cargo area. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.
Driver Controls Press and pull the window switches to open and close windows. • Push down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close. AUTO One touch down Allows the driver’s window to open fully without holding the control down. Push the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.
Driver Controls The power vent windows are operated by a single switch located on the instrument panel. Press and hold the bottom of the switch to open or the top of the switch to close both vent windows. A sound will be heard when opening and closing the vent windows. This is a normal noise that informs you the windows are operating. AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function.
Driver Controls Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Signal indicator mirrors (if equipped) When the turn signal is activated, the appropriate mirror will show a blinking yellow arrow.
Driver Controls POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 2.8 inches (73 mm) of maximum travel. Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.
Driver Controls 3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. light on the 5. The indicator instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed. • If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage.
Driver Controls • Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control. Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST - control until you get to the desired speed, then release the control. You can also use the CST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).
Driver Controls STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features • Press MEDIA to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: • Press SEEK to access the next/previous strong station. In Tape mode: • Press SEEK to listen to the next/previous selection on the tape. In CD mode: • Press SEEK to listen to the next/previous track on the disc. In any mode: • Press VOL up or down to adjust the volume. • Press MUTE to mute the volume.
Driver Controls When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).
Driver Controls 3. Simultaneously press and hold both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons. Note: Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 4.
Driver Controls Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2 outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.
Driver Controls Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section.
Driver Controls Info menu This control displays the following options: • Odometer • Distance to Empty • Trip Odometer • Average Fuel Economy • Trip Elapsed Drive Time • Display On/Off (top two lines) INFO SETUP RESET Odometer/Trip Odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions.
Driver Controls • variations in top-off procedure from one fill-up to another • rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings.
Driver Controls Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control for 2 seconds to set the language choice. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric.
Driver Controls Pressing the RESET control cycles the message center through each of the systems being monitored and will display the following only when there is a malfunction. 1. Oil life in XX% 2. Charging system 3. Washer fluid level 4. Brake fluid level 5. Liftgate status 6. Exterior lamps status 7. Traction Control娂 status 8. Tire pressure monitoring system 9. Fuel level status (hold to reset to relearn) 10.
Driver Controls Warning display Status Driver’s door ajar Warning cannot be reset Passenger door ajar Left rear door ajar Right rear door ajar Park brake set Warning returns after 10 minutes Check brake system Liftgate ajar Warning returns after the ignition key is turned from OFF to ON Check left park lamp Check right park lamp Check left headlamp Check right headlamp Check left turn lamp Washer fluid low Check right turn lamp Low fuel level Change oil soon Low tire pressure Tire pressure monitor fault Tir
Driver Controls CHECK BRAKE LAMPS. Displayed when the brake lamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. The center high-mount brakelamp is not monitored. CHECK LEFT OR RIGHT HEADLAMPS. Displayed when the headlamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK LEFT OR RIGHT PARK LAMPS.
Driver Controls To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press the SETUP control to access the System Check function. 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Press and hold the RESET control to display “OIL LIFE SET TO 100%”. Your oil life is now reset.
Driver Controls 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display “OIL LIFE XX% RESET TO ALTER”. 5. Press RESET until you find your personalized OIL LIFE XX%. 6. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check.
Driver Controls POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. To install floor mats that have a retention post: Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Driver Controls POWER LIFTGATE (PLG) (IF EQUIPPED) With this option, you can power open or close the liftgate with the provided controls. • overhead console button • remote entry transmitter button • outside release handle • liftgate trim-mounted switch (closing) Opening and Closing the PLG: The PLG controls will operate without having the key in the ignition. The transaxle must be in PARK to power operate the PLG, when the key is in the ignition and turned to the ON position.
Driver Controls The Power Door Lockout Control is located in the overhead console. With the control in the OFF position, power operation is disabled from the liftgate handle and from the liftgate trim switch. The overhead console switch and remote entry transmitter will operate the liftgate regardless of the position of the lockout switch. To power open or close the PLG from the Overhead console: 1. Press and release the control to power open the PLG. 2.
Driver Controls Note: Continued force applied after unlatching may activate the obstacle detection feature and stop the power system. For the best performance allow the power system to open the PLG after releasing the handle. To power close the PLG from the liftgate trim switch: 1. Ensure the Power Door Lockout Control is in the ON position. 2. Press and release the control on the bottom of the liftgate trim panel to engage the power assist feature.
Driver Controls If any of these conditions occur, the PLG must be reset. To reset the PLG: 1. Manually close and fully latch the liftgate. 2. Power open the liftgate by using the remote entry transmitter or overhead console button. 3. Once the liftgate is fully open, close the liftgate using the power switch on the liftgate, remote entry transmitter or overhead console button. Liftgate ajar signal If the liftgate is not fully latched, you will receive a “LIFTGATE AJAR” message on the instrument panel.
Driver Controls Utility hooks The utility hooks can be used to hang small items. Do not hang more than 20 lb. (12 kg) on each of the hooks. The hooks are not designed to restrain objects during a collision. LUGGAGE RACK (IF EQUIPPED) Maximum load is 125 lbs (57 kg) on the roof rack structure, or 100 lbs (45 kg) on the roof panel, evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. To adjust the cross-bar (if equipped) position: 1.
Driver Controls To remove the cross-bar assembly (if equipped): 1. Remove rear support covers from the rear rails. Place a small object into the pin holes and slide the cover out towards the rear of the vehicle. 2. Loosen the thumbwheel at both ends of the cross-bar and slide the cross-bar towards the rear of the vehicle. 3. De-press the metal retention clip located in the inner rail channel on both sides, and slide the crossbar out simultaneously.
Driver Controls To reinstall the cross-bar assembly (if equipped): 1. Slide the cross-bar into the rail track with the arrow facing towards the front of the vehicle. Slide the bar forward passed the retaining clip. 2. Firmly tighten the thumbscrews at both ends of the cross-bar. 3. Install both support covers by sliding the covers back into the channel and pushing gently into place. Note: When the cross-bars are not in use, remove or move the cross-bars to the back of the roof rack for optimum wind noise.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock娂 passive anti-theft system section in this chapter for more information. POWER DOOR LOCKS Press the top portion of the control to unlock all doors and the bottom portion to lock all doors.
Locks and Security 1. Locate the liftgate trim access panel in the center of the liftgate. 2. Using your key, a small screwdriver or knife, pry off the access panel. 3. Using your key, a small screwdriver or knife, poke or cut a hole in the liftgate door foam as large as the access window and move the lock/unlock lever accordingly: • For vehicles without power liftgate, pull the lock/unlock lever to the right (drivers side).
Locks and Security Relock The autolock feature repeats when: • an “autolock” occurrence has already taken place, • the brake is depressed while vehicle speed is less than 5 mph (8 km/h), • all vehicle doors become closed again, and • the vehicle increases to more than 5 mph (8 km/h). Deactivating/activating the autolock feature The autolock feature can be enabled or disabled by the keyless entry keypad (if equipped) on your door, driver configuration mode or by your authorized dealer.
Locks and Security 4. Press the power door unlock control three times. 5. Turn the ignition back to the 4 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the 3 (OFF) position. The horn will chirp once to confirm the procedure is complete.
Locks and Security • • • • nearby radio towers, structures around the vehicle, or other vehicles parked next to your vehicle. 3–button remote • 5–button remote • 6–button remote The remote entry system allows you to: • lock or unlock all vehicle doors and liftgate without a key. • unlock/open a driver’s side power sliding door and/or passenger side power sliding door (if equipped). • unlock/open the power liftgate (PLG) (if equipped).
Locks and Security • activate the personal alarm. • arm and disarm the perimeter anti-theft system (if equipped). If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press and release to unlock the driver’s door. Note: The interior lamps will illuminate and the anti-theft system (if equipped) will disarm.
Locks and Security Opening power liftgate (PLG) (if equipped) Press the control twice within three seconds to power open the power liftgate. The interior lamps will illuminate. Make sure all persons are clear of the power liftgate area before using the power liftgate controls to open or close the liftgate. Press the control another two times within three seconds to close the power liftgate and turn off the interior lights.
Locks and Security If any of the doors, the liftgate or the hood (if equipped with perimeter alarm) are not properly closed, the horn will make two quick chirps and the parklamps will not flash. Sounding a panic alarm Press to activate the alarm. The alarm will cycle the horn, the turn signals will flash, and the interior lamps will illuminate. Press again or turn the ignition to the 4 (ON) or the 1 (ACCESSORY) position to deactivate.
Locks and Security Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery.
Locks and Security Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of six) available before beginning this procedure.
Locks and Security Illuminated entry The interior lamps illuminate when the key in the driver’s door lock cylinder (if equipped with perimeter alarm), the keyless entry system or the remote entry transmitter is used to unlock the door(s), power sliding doors (if equipped) or liftgate.
Locks and Security The system will automatically turn off if: • the vehicle is locked using the remote entry system, the keyless entry keypad, or • the ignition is turned to the 4 (ON) position, or • after 25 seconds of illumination. Deactivating/activating perimeter lamps You may enable/disable this feature by having your vehicle serviced by your authorized dealer. You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature: 1.
Locks and Security KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • • • • lock or unlock the doors without using a key. activate or deactivate the autolock feature. open and close the right and left power sliding doors (if equipped). recall memory seat/side view mirrors/adjustable pedals position Driver 1 or Driver 2 (if equipped).
Locks and Security • Press 1 • 2 to recall the Driver 1 position. • Press 3 • 4 to recall the Driver 2 position. 5. After five seconds of keypad inactivity, programming mode is exited. All of the vehicle doors will lock and unlock to confirm the code has been stored. Each memory feature driver position (Driver 1 or Driver 2) can be associated with only one personal code. The factory-set code cannot be associated with a memory recall position.
Locks and Security To open (or close) the power sliding doors (if equipped), press the 5 • 6 control within five seconds to open (or close) the left power sliding door or the 9 • 0 control in order to open (or close) the right power sliding door. SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used.
Locks and Security If any of these items are present, you need to prevent these objects from touching the coded key while starting the engine. These objects cannot damage the coded key, but may cause a momentary “no start” condition if they are too close to the key when starting the engine. If a problem occurs, turn the ignition to the 2 (OFF) position and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved coded key.
Locks and Security 1. Insert the first previously 4 programmed coded key into the 3 ignition and turn the ignition from 5 the 3 (OFF) position to the 4 (ON) position [maintain ignition in 4 (ON) 2 for at least three seconds, but no more than ten seconds]. 2. Turn ignition from the 4 (ON) 1 position back to the 3 (OFF) position in order to remove the first coded key from the ignition. 3.
Locks and Security PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting. Arming the system When armed, this system will help protect your vehicle from unauthorized entry.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward. Pull lever up to adjust seatback.
Seating and Safety Restraints Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Using the manual lumbar support (if equipped) The lumbar control is located on the inboard side of the seat under the armrest.
Seating and Safety Restraints To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check Passenger Airbag Disable Indicator for proper Airbag Status. Refer to Front Passenger Sensing System chapter for additional details.
Seating and Safety Restraints Heated seats (if equipped) To operate the heated seats: • Push the control located on the climate control system panel once to activate high heat. • Push twice to activate low heat. • Push a third time to deactivate. The indicator light on the control will illuminate when activated. For low heat, one light will be lit; for high heat, both lights will be lit. The heating of the seat turns off after 10 minutes or when the vehicle is turned off.
Seating and Safety Restraints REAR SEATS Head restraints Lift the head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up and down by pulling up on the head restraint. Push button to lower head restraint. Seat mounted cup holders (if equipped) Deploy by pressing the button on top of the cupholder.
Seating and Safety Restraints The cupholder is designed to detach from the seat when subjected to heavy load. The cupholder can be reinstalled by returning to the closed position. Use only soft cups in the cupholder. Hard objects can injure you in a collision. Adjusting 2nd row seats (if equipped) Lift control to adjust seat forward or backward.
Seating and Safety Restraints • 2nd row bench seat (if equipped) Note: This seat can be moved forward to keep a child in a LATCH child restraint attached to the LATCH anchors at the center of the bench seat close to the front seat occupants or to increase cargo room without removing the seat. The seat should be moved to the full rearward position when it is occupied by older children or adults, and when child seats are installed at the seating positions.
Seating and Safety Restraints Accessing the third row seat with a second row bucket seat Ensure head restraint is in the full down position and seat is adjusted to full rear position (if equipped). Note: Place the front row seat in a forward position to allow the 2nd row to be fully upright. Lift the handle located on the rear lower corner of the seat. The seat back will fold flat.
Seating and Safety Restraints Continuing to lift the handle will tumble the seat forward, allowing easier access to the third row seat. After entering the 3rd row seat, return the seat from the tumbled position and latch it to the floor. Operate recline control to return the seatback to the upright position.
Seating and Safety Restraints • Ensure that the seat and seatback is latched securely in position. • Keep floor area free of objects that would prevent proper seat engagement. • Do not adjust or release the seat floor latch while vehicle is in motion. • Do not operate the vehicle with seats in tumbled position. Failure to do any of these could result in personal injury. Always latch the vehicle seat to the floor, whether the seat is occupied or empty.
Seating and Safety Restraints After entering the 3rd row, pull back the seatback until it latches. This will latch and lock the seatback and the seat track. The seatback and seat will not return to their original position. Note: Ensure the front row seat is in a forward position to allow the seat to return.
Seating and Safety Restraints Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Note: Do not attempt to return the seat by pushing on the seatback, as this will cause the seat tracks to re-lock before the seat can be returned.
Seating and Safety Restraints 5. Rotate the seat rearward at a 30 to 45 degree angle. 6. With the assist handle, pull the seat rearward. 7. Remove the seat from vehicle. Second row bench seat 1. Detach the lap/shoulder belts from both sides of the seat by inserting a safety belt tongue or key into the buckle release slot, pushing upward as shown, and pulling out the mini-tongue on the end of the safety belt.
Seating and Safety Restraints 2. Find the clips attached near the ends of the lap/shoulder belts. 3. Clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel. The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.
Seating and Safety Restraints 4. Position seatback in full down position. 5. From behind seat pull straight back on the release handles located on each side of the seat, releasing the rear floor latches. 6. Lift up the seat by the release handles to clear the floor latches and then pull the seat rearward until the front hooks have come out of the floor tubs. 7. Remove the seat.
Seating and Safety Restraints 2. Install seat onto rear pin of front tub at a 30 to 45 degree angle. 3. Rotate the seat forward until it latches onto the front pin. 4. Rotate seat rearward until the back of the seat latches onto the floor.
Seating and Safety Restraints 5. Operate recline lever and push the seat back upright. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
Seating and Safety Restraints 3. Lower back of seat onto the rear tubs until both release controls latch into place. Be sure that the seat is locked in place both front and back. Do not place the seat front hooks on the front most pin of the front tub. Doing so will not allow the seat to fully install in vehicle. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop. Stowing the third row seat 1.
Seating and Safety Restraints 2. If you plan to carry very large objects or items that might damage the center lap/shoulder belt, detach the belt from the seat. Use a key or safety belt tongue to release the buckle. 3. Store the tongue of the sliding latchplate in the belt pocket.
Seating and Safety Restraints 4. Store the belt in the housing found on the ceiling by inserting the smaller tongue in the slot provided. Note: The seat can be stowed with the safety belt connected if desired. Store the tongue of the sliding latchplate in the belt pocket to avoid potential damage to the seat. 5. Push the head restraint release buttons and move the head restraints fully down. Remove all objects from the seat and stowage tub.
Seating and Safety Restraints 6. From the rear of the vehicle, fold seat back by pulling and releasing the number 1 strap. Important: If you don’t let go of the number 1 strap before the seat back folds completely, the seat may not stow flat in the tub. Refer to the label attached to the rear of the vehicle seat. 7. Release the cushion latches by pulling the number 2 strap.
Seating and Safety Restraints 8. Pull the number 3 strap on the seat back to tumble seat all the way in to the tub in the floor. Do not use the seat anchors as cargo tie downs. Unstowing the third row seat Ensure seat latching area is free of objects. 1. Lift the seat out of the tub in the floor by pulling up on the exposed strap or handle. Once seat is at a vertical position, push the seat over, letting it fall onto the latches.
Seating and Safety Restraints 2. To return the seat back to the seating position, pull the number 1 strap, then while holding the number 1 strap, pull the number 3 strap to raise the seat back. 3. Release the number 1 strap to allow the seat to lock, then release the number 3 strap. 4. Pull up on the head restraints to adjust them. 5.
Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Tailgate function The 3rd row seat is equipped with a tailgate function to be utilized when the vehicle is parked and engine turned off. This rearward-facing position allows the customer to open the liftgate and sit facing out of the vehicle rearward. This is not a position suitable for driving.
Seating and Safety Restraints 3. To return the seat, ensure seat latching area is free of objects. Then, raise the seat off the liftgate scuff plate and push at the top of the seat back to rotate the seat back onto the latches. Pull up on the head restraints to raise them. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop.
Seating and Safety Restraints How does the Personal Safety System姟 work? The Personal Safety System娂 can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM).
Seating and Safety Restraints Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking.
Seating and Safety Restraints Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the Safety Canopy娂 system. This helps increase the effectiveness of the safety belts.
Seating and Safety Restraints Safety belt precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. All restraints in the vehicle are combination lap and shoulder belts.
Seating and Safety Restraints All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.
Seating and Safety Restraints Safety belt extension assembly If the safety belt is too short when fully extended, a 9 inch (23 cm) or 12 inch (31 cm) safety belt extension assembly can be added (part numbers 611C22–A and 611C22–B respectively). These assemblies can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position...
Seating and Safety Restraints Both the driver’s and passenger’s safety belt usages are monitored and either may activate the Belt-Minder威 feature. The warnings are the same for the driver and the front passenger. If the Belt-Minder威 warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder威 feature. If...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers.
Seating and Safety Restraints Reasons given... “I have an airbag” “I’d rather be thrown clear” Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder威 chime.
Seating and Safety Restraints • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled While the design allows you to deactivate your Belt-Minder威, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the Belt-Minder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the Belt-Minder威 feature while driving the vehicle. 1.
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system (SRS) is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts.
Seating and Safety Restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm) between an occupant’s chest and the driver airbag module. Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries.
Seating and Safety Restraints Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag.
Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and Safety Restraints • • • • • • one or more impact and safing sensors. Safety belt pretensioner a readiness light and tone. diagnostic module. and the electrical wiring which connects the components. Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system. later in this chapter.
Seating and Safety Restraints For side airbag equipped vehicles, the front passenger sensing system will turn off the passenger seat side airbag if: • the seat is empty and safety belt is unbuckled. The front passenger sensing system uses a ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located in the center stack of the instrument panel to the right of the radio.
Seating and Safety Restraints • Have the person sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended. • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag. • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.
Seating and Safety Restraints Objects Pass Airbag Off Indicator Lamp Unlit Passenger Airbag Small (i.e. 3 ring Disabled binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.
Seating and Safety Restraints A difficulty with the system is indicated by one or more of the following: • The readiness light (same light for front and side airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired.
Seating and Safety Restraints Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. The front passenger sensing system will disable the side airbag if the seat is empty. The side airbag system consists of the following: • An inflatable nylon bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment.
Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and Safety Restraints All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy娂 system is provided. To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy娂.
Seating and Safety Restraints Children 12 years old and under should always be properly restrained in the second or third row seats. The Safety Canopy娂 will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening.
Seating and Safety Restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with the system is indicated by one or more of the following: • The readiness airbag light (same light as for front airbag system) will either flash or stay lit.
Seating and Safety Restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat.
Seating and Safety Restraints When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lb. (36 kg) (about 8 to 12 years old).
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Either type can be used at any seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). Children and booster seats vary widely in size and shape.
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride. Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use.
Seating and Safety Restraints When installing a child safety seat: • Review and follow the information presented in the Airbag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Children 12 and under should be properly restrained in the rear seat whenever possible. 1. Position the child safety seat in a seat with a combination lap and shoulder belt.
Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
Seating and Safety Restraints The tether anchors in your vehicle are in the positions shown: The front passenger seat with power adjustment does not have a tether anchor. The two tether anchors on the back of the second row bench seat can be used either for child safety seats at the two seating positions, or either anchor can be used for a single LATCH child seat installed at the center of the bench seat. Front passenger seating position (manual adjusting seats only) 1.
Seating and Safety Restraints 2. Route the child safety seat tether strap over the back of the seat. If the head restraint is adjustable, route the tether strap under the head restraint and between the head restraint posts. If the top of the safety seat hits the head restraint, raise the head restraint to let the child seat fit further rearward. 3. Grasp the tether strap and position it to the seat frame. 4. Rotate the tether hook, and clip the tether strap to the seat frame.
Seating and Safety Restraints If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision. 5. Rotate the tether strap clip. 6. Install the child safety seat tightly using the LATCH anchors or safety belts. Follow the instructions in this chapter. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Seating and Safety Restraints Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket • 2nd row bench • 3rd row bench For additional important safety information on the proper use of safety belts, child seats and infant seats, please read the entire Seating and safety restraints chapter in this owner’s guide.
Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol. If your vehicle has a second row bench seat, one child seat can be placed in each outboard seating position, or one LATCH child seat can be placed in the center of the seat only. Please note that the center-only position does not have a separate tether anchor. Either of the outboard tether anchors may be used for the center position.
Seating and Safety Restraints Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Attach LATCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Tires, Wheels and Loading The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tires, Wheels and Loading • • • • • • • • • Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. kPa: Kilopascal, a metric unit of air pressure. PSI: Pounds per square inch, a standard unit of air pressure. Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 km).
Tires, Wheels and Loading Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙blowout⬙, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents.
Tires, Wheels and Loading Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure with the tire gauge. 3. Add enough air to reach the recommended air pressure.
Tires, Wheels and Loading Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1.
Tires, Wheels and Loading If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Highway hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway.
Tires, Wheels and Loading • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the sensor. It is recommended that you always have your tires serviced by an authorized dealer.
Tires, Wheels and Loading When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your Tire Pressure Monitoring System: Low Tire Pressure Possible cause Customer Action Required Warning Light Solid Warning Light Tire(s) 1.
Tires, Wheels and Loading Low Tire Pressure Possible cause Customer Action Required Warning Light Flashing Warning Spare tire in use Your temporary spare tire is in Light use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to When your temporary spare tire is installed in this section.
Tires, Wheels and Loading any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains.
Tires, Wheels and Loading VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance.
Tires, Wheels and Loading The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.
Tires, Wheels and Loading Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.
Tires, Wheels and Loading Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information.
Tires, Wheels and Loading The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity. You decide to go golfing. Is there enough load capacity to carry you, 4 of your friends and all the golf bags? You and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each.
Tires, Wheels and Loading TRAILER TOWING Your vehicle is capable either of towing Class I trailers or up to Class II trailers when equipped with the optional trailer tow package. If your vehicle does not have the optional trailer tow package your vehicle is partially prepped for trailer tow lamp wiring but you will also need to install electrical kit (15A416).
Tires, Wheels and Loading Vehicle towing capability/Trailer hitch requirement Model/ Engine Van, 3.9L Wagon, 3.9L Wagon, 4.2L Wagon, 3.9L with trailer tow option Wagon, 4.2L with trailer tow option Trailer GCWR lb. (kg) Hitch type required Trailer Weight range - lb. (kg) Tongue load 7000 (3175) Class I Non-Equalizing Weight Carrying 0-2000 (0–907) 10–15% of TW (200 lb. [91 kg] maximum) Class II Non-Equalizing Weight Carrying 0–3500 (0-1588) 10–15% of TW (350 lb.
Tires, Wheels and Loading Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch that does not exceed your vehicle’s capability. See the Tongue Load section in the trailer towing chart earlier in this section for range details on a specific trailer load. Safety chains Always connect the trailer’s safety chains to the hook retainers on the hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners.
Tires, Wheels and Loading Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer, and don’t make full throttle starts. • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling.
Tires, Wheels and Loading RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Front Wheel Drive (FWD) vehicles: It is not recommended to tow front wheel drive vehicles with the front drive wheels on the ground.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Driving Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving • Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START) 4 without pressing the accelerator 3 pedal and release as soon as the 5 engine starts.
Driving Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant which aids in starting and heater/defroster performance. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -10°F (-23°C) or below.
Driving ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates ABS when the ignition is turned on. If the light does not illuminate during start up, remains on or flashes, the ABS may be disabled and may need to be serviced. Even when the ABS is disabled, ! P normal braking is still effective. (If your BRAKE warning lamp BRAKE illuminates with the parking brake released, have your brake system serviced immediately by an authorized dealer.
Driving Parking brake To set the parking brake, pull the handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. To release, press and hold the button, pull the handle up slightly, then push the handle down. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
Driving • • • • Maneuvering quickly to avoid an accident, pedestrian or obstacle Hitting a patch of ice Changing lanes on a snow-rutted road Entering a snow-free road from a snow-covered side street, or vice versa • Entering a paved road from a gravel road, or vice versa • Hitting a curb while turning • Cornering at excessive speeds while towing a heavily loaded trailer (refer to Trailer Towing in this chapter) The AdvanceTrac威 system automatically turns on when the engine is started.
Driving • A slight deceleration of the vehicle • The AdvanceTrac威 indicator light will illuminate • If your foot is on the brake pedal, you will feel a vibration in the pedal. • If the driving condition is severe and your foot is not on the brake, the brake pedal will move to apply higher brake forces. You may also hear a whoosh of air from under the instrument panel during this severe condition. All these conditions are normal during AdvanceTrac威 operation.
Driving • Heavy or uneven steering efforts may be caused by a low power steering fluid level. Check for a low power steering fluid level before seeking service by your authorized dealer. • Do not fill the power steering fluid reservoir above the MAX mark on the reservoir, as this may result in leaks from the reservoir. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort.
Driving When the key is in the ignition and in the 3 (OFF) position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. To avoid unwanted vehicle movement, always set the parking brake. 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter.
Driving Understanding the gearshift positions of the 4–speed automatic transaxle P (Park) This position locks the transaxle and prevents the front wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Driving 1 (First) • Transaxle operates in first gear only. • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle.
Driving To help avoid personal injury, always use caution when in R (Reverse) and when using the RSS. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
Driving The RSS is automatically enabled OFF when the gear selector is placed in R (Reverse) and the ignition is ON. The park aid disable switch allows the driver to disable the RSS only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled. If the indicator light illuminates when the RSS is not turned off, it may indicate a failure in the RSS. The system defaults to enabled every time the ignition is turned on.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the period of five years or 60,000 miles (100,000 km), whichever occurs first on Ford and Mercury vehicles, and six years or 70,000 miles (110,000 km) on Lincoln vehicles.
Roadside Emergencies • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Customer Information Guide in the glove compartment. U.S.
Roadside Emergencies FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. This switch is located behind the service panel on the right side of the cargo area. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 Fuse Amp Rating Relay Relay 10A 5A 20A 6 5A 7 8 10A 10A 9 10A 10 11 5A 5A Passenger Compartment Fuse Panel Description Accessory delay relay 1 Accessory delay relay 2 Front wiper motor Run feed B+ feed to outside mirrors Vent window power feed/Radio feed Driver door switch illumination/Passenger door switch illumination Rear wiper Run feed Cluster/Electronic Automatic Temperature Control (EATC) B+ feed, DVD Passive
Roadside Emergencies Fuse/Relay Location 12 Fuse Amp Rating 5A 13 5A 14 5A 15 16 10A 5A 17 10A 18 10A 19 5A 20 10A 21 10A 232 2007 Freestar (win) Owners Guide (post-2002-fmt) USA (fus) Passenger Compartment Fuse Panel Description Brake-Shift Interlock (BSI) Run feed, Climate control system Run feed Compass/Driver heated seat/Passenger heated seats/Reverse sensing system/Power Liftgate Module/Power sliding door Run feeds Underhood fuse box Run feed, Front blower Run feed Brake On-Off (BOO
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies The high-current fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 Fuse Amp Rating — 30A** 30A** 30A** 30A** 30A** 7 8 30A** 40A** 9 10 30A** 30A** 11 12 13 14 30A** 40A** 40A** 30A** 15 16 20 30A** 30A** Mini relay 21 22 23 24 25 26 27 28 29 30 31 Mini relay Micro relay Micro relay Mini relay Micro relay — — Mini relay Micro relay Micro relay Micro relay 234 2007 Freestar (win) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description Not used Ri
Roadside Emergencies Fuse/Relay Location 32 40 Fuse Amp Rating Mini relay 15A* 41 42 43 25A* 10A* 15A* 44 45 46 47 10A* 15A* 20A* 15A* 48 49 50 51 — 10A* 10A* 10A* 52 53 54 55 56 57 58 20A* 10A* 30A* 25A* 30A* — 30A* 59 60 20A* 30A* Power Distribution Box Description Rear defroster Engine #1 (A/C relay coil, IMRC, HEGO sensors, Canister purge, Transmission module) Horn A/C clutch Engine #2 (Cooling fan relays, Injectors, PCM, MAF sensor, IAC, Ignition coil, ESM) Heated PCV High beams Trailer sto
Roadside Emergencies Fuse/Relay Location 61 62 Fuse Amp Rating — 30A* 63 20A* 64 65 20A* 30A* 66 20A* 67 20A* 70 — 71 — 72 — 73 — 74 — 75 Diode 76 Diode * Mini Fuse ** Cartridge Fuse 236 2007 Freestar (win) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description Not used SJB #3 – Right cornering/auxiliary lamps, Right low beam, Left front park/turn lamps, Left rear park/stop/turn lamps, Instrument panel courtesy lamps, Step well lamps, Left signal mirror, Clock, Cluster, Message
Roadside Emergencies Auxiliary relay box (cooling fans) The relay box is located in the engine compartment by the radiator.
Roadside Emergencies The use of tire sealants may damage your tires. The use of tire sealants may also damage your Tire Pressure Monitoring System and should not be used. Your vehicle is equipped with a Tire Pressure Monitoring System. Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function.
Roadside Emergencies • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire.
Roadside Emergencies Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible. Location of the spare tire and tools Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use.
Roadside Emergencies Removing the spare tire 1. Wagon only: Open liftgate and lift flap in the carpeting on the rear tub cargo floor to expose the hex nut. Insert the lug nut wrench on the hex nut in cargo floor. Cargo van only: Lift flap in mat to expose hex nut. Insert extension tool through access hole and engage hex nut. Place lug wrench onto end nut of extension tool. 2. Turn the wrench counterclockwise until cable is slack and tire can be slid rearward. 3.
Roadside Emergencies Tire change procedure When one of the front wheels is off the ground, the transaxle alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
Roadside Emergencies 3. Remove the spare tire, jack and lug wrench. 4. Removing the optional wheel cover or center ornament: • To remove a bolt-on wheel cover (if equipped) loosen the plastic nuts on the center ornament with the wheel nut wrench. Then, remove the wheel cover with the tapered end of the wheel nut wrench. • Remove the center ornament (if equipped) from the wheel with the tapered end of the wheel nut wrench. Insert and twist the handle, then pry against the wheel. 5.
Roadside Emergencies If Ford Accessory Running Boards have been installed, use the jack adapters supplied with the running boards as described on the inside of the jack storage area. 6. Locate the jack notch next to the door closest to the tire you are changing, then place the jack on the frame rail directly behind the notch. 7. Turn the jack handle clockwise until the wheel is completely off the ground.
Roadside Emergencies 11. Remove the jack and fully 1 tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this 3 4 chapter for the proper lug nut torque specification. 12. Installing the optional wheel cover or center ornament: 5 2 • If equipped with a bolted-on wheel cover, install the wheel cover and tighten the five plastic nuts until they click (do not use power tools on these nuts).
Roadside Emergencies 3. Lay the tire flat and secure the cable with wing screw by installing it on the wing screw retainer in the floor and turning the wing screw clockwise. You will hear an audible click when the tire is properly secured. 4. Check that the flat tire is properly secured. Stowing the spare tire 1. Lay the spare, inflated tire on the ground with the valve stem facing down. 2. Insert the primary wheel retainer through the center of the wheel. 3.
Roadside Emergencies WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N•m 1⁄2 x 20 100 135 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.
Roadside Emergencies 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed by wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you.
Customer Assistance Additional Assistance If you still have a complaint involving a warranty dispute, you may wish to contact the Better Business Bureau (BBB) AUTO LINE program (U.S. only). In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Customer Assistance In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126 THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.
Customer Assistance You can get more information by calling BBB AUTO LINE at 1–800–955–5100, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800 Arlington, Virginia 22203–1833 Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation. UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers.
Customer Assistance You may purchase Ford ESP from any participating authorized dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 4,600 participating authorized dealers.
Customer Assistance If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations. Customers in the U.S. should call 1–800–392–3673. ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product.
Cleaning ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean.
Cleaning WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield.
Cleaning • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system.
Cleaning Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaning the seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect performance of the side airbag in a collision. LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather.
Cleaning FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Customer Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod. Your vehicle’s hood has two locations for the prop rod to be placed. These locations provide two different hood opening positions. Use the location which best suits your needs.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.9L/4.2L V6 engines 10 9 2 1 8 7 6 1. Brake fluid reservoir 2. Air filter assembly 3. Power distribution box 4. Battery 5. Automatic transmission fluid dipstick 6. Engine oil dipstick 7. Engine oil filler cap 8. Windshield washer fluid reservoir 9. Engine coolant reservoir 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to the Maintenance product specifications and capacities section in this chapter.
Maintenance and Specifications CHANGING THE WIPER BLADES To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard. Replace wiper blades at least once per year for optimum performance.
Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter.
Maintenance and Specifications • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent SAE 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Maintenance and Specifications It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. This will minimize the discharge of your battery during storage. Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability. Batteries normally produce explosive gases which can cause personal injury.
Maintenance and Specifications RN TU LE AD RE Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2.
Maintenance and Specifications ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060).
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.
Maintenance and Specifications For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “FULL COLD” level.
Maintenance and Specifications Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and Specifications • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. FUEL FILTER For fuel filter replacement, see your authorized dealer.
Maintenance and Specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and Specifications Refueling • • • • • • Fuel vapor burns violently and a fuel fire can cause severe injuries.
Maintenance and Specifications If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Maintenance and Specifications Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally, adding one gallon of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than one gallon may be required. indicator may come on.
Maintenance and Specifications For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than three automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand.
Maintenance and Specifications Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually.
Maintenance and Specifications Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy.
Maintenance and Specifications • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in scheduled maintenance information performed according to the specified schedule. The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system.
Maintenance and Specifications On board diagnostics (OBD-II) Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD-II). The OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also assists your authorized dealer in properly servicing your vehicle.
Maintenance and Specifications If the indicator is on or the bulb does not work, the vehicle may need to be serviced. Refer to the On board diagnostics (OBD-II) description in this chapter. If the vehicle’s engine or transmission has just been serviced, or the battery has recently run down or been replaced, the OBD-II system may indicate that the vehicle is not ready for I/M testing.
Maintenance and Specifications 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the correct operating range. Be sure to put the cap back on the reservoir. BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced.
Maintenance and Specifications 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature.
Maintenance and Specifications Use of a non-approved automatic transmission fluid may cause internal transaxle component damage. If necessary, add fluid in 1/2 pint (250 mL) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Maintenance and Specifications Reposition the locking clip (on the connector) and squeeze connector to remove. 2. Loosen the hose clamp located closest to the air cleaner. 3. Remove the air cleaner assembly from the vehicle.
Maintenance and Specifications 4. Release the two clamps that secure the cover to the air filter housing and place the cover aside. 5. Remove the air filter element from the air filter housing. 6. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 7. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover.
Maintenance and Specifications 8. Replace the air filter housing cover and secure the clamps. Be sure all the tabs on the bottom edge are properly aligned. 9. Reinstall the air cleaner assembly into the vehicle. Ensure the tabs on the inlet tube are secure in the sheet metal.
Maintenance and Specifications 10. Ensure the pads on the bottom of the air cleaner assembly are properly seated. 11. Reconnect the outlet tube to the air cleaner assembly and tighten the clamp. 12. Reconnect the Mass Air Flow Sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in “locked” position.
Maintenance and Specifications MOTORCRAFT PART NUMBERS Component Air filter element Battery Fuel filter Oil filter PCV valve Spark plugs 3.9L OHV V6 engine FA-1679 BXT-59 BXT-65-750 FG-986B FL-400S 4.2L OHV V6 engine FA-1679 BXT-59 BXT-65-750 FG-986B FL-400S 1 2 1 The PCV valve is a critical emission component. It is one of the items listed in scheduled maintenance information and is essential to the life and performance of your vehicle and to its emissions system.
2007 Freestar (win) Owners Guide (post-2002-fmt) USA (fus) — 14.8 quarts (14.0L) 15.9 quarts (15.0L) Door weatherstrips Engine coolant without rear heater Engine coolant with rear heater Cooling system stop leak pellets Door latch, hood latch, auxiliary hood latch, door and liftgate hinges, striker plates, seat tracks, sliding door both sides (upper and lower track) and fuel filler door hinge.
2007 Freestar (win) Owners Guide (post-2002-fmt) USA (fus) 26.0 gallons (98.4L) Fuel tank — Motorcraft MERCON威V ATF2 Motorcraft Premium Windshield Washer Concentrate Motorcraft MERCON威 ATF Motorcraft Penetrating and Lock Lubricant Ford part name — ZC-32-A / WSB-M8B16-A2 Ford part number / Ford specification XL-1 / None XT-2-QDX / MERCON威 XT-5-QM / MERCON威V Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 3.9 L OHV V6 engine 232 87 octane 1-4-2-5-3-6 EDIS 0.052–0.056 inch (1.32–1.42mm) 9.36:1 4.2L OHV V6 engine 256 87 octane 1-4-2-5-3-6 EDIS 0.052–0.056 inch (1.32–1.42mm) 9.27:1 Engine drivebelt routing • 3.9L V6 and 4.
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure (B-Pillar) by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint System 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on the Safety Compliance Certification Label.
Accessories GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications.
Accessories Peace of mind Mobile-Ease娂 hands-free communication system Remote start Vehicle security systems Wheel locks Not all accessories are available for all models.
Index A Accessory delay ..........................68 AdvanceTrac ..............................218 Air cleaner filter ...............297, 302 Air filter, cabin ............................44 Airbag supplemental restraint system ........................153, 162, 164 and child safety seats ............155 description ..............153, 162, 164 disposal ....................................167 driver airbag ............155, 162, 165 indicator light .................161, 167 operation .................
Index wiper blades ............................264 Clock ............................................66 Compass, electronic ....................58 calibration .................................60 set zone adjustment .................59 Console ........................................65 overhead ....................................58 Controls power seat ...............................115 steering column ........................74 Coolant checking and adding ..............278 refill capacities ................
Index capacity ...................................303 choosing the right fuel ...........286 comparisons with EPA fuel economy estimates .................291 detergent in fuel .....................287 filling your vehicle with fuel ..................283, 285, 288 filter, specifications ........283, 302 fuel pump shut-off switch .....229 improving fuel economy ........288 octane rating ...................287, 305 quality ......................................287 running out of fuel .................
Index headlamps, flash to pass ..........46 instrument panel, dimming .....47 interior lamps .....................49–51 replacing bulbs ...................53, 55 Lane change indicator (see Turn signal) ........................49 Liftgate ............................87–88, 92 remote release ..................95, 101 Lights, warning and indicator ....10 anti-lock brakes (ABS) ..........217 Load limits .................................202 Locks autolock .....................................96 childproof ......
Index Roadside assistance ..................227 Roof rack .....................................92 S Safety Belt Maintenance ..........147 Safety belts (see Safety restraints) ..................138, 142–145 Safety Canopy ...........................164 Safety defects, reporting ..........260 Safety restraints ........138, 142–145 Belt-Minder威 ...........................148 extension assembly ................147 for adults .........................143–145 for children .....................
Index fluid, refill capacities ..............303 lubricant specifications ..........303 Transmission brake-shift interlock (BSI) ....221 fluid, checking and adding (automatic) .............................295 Turn signal ..................................49 V Vehicle Identification Number (VIN) ..........................................306 Vehicle loading ..........................202 Ventilating your vehicle ...........216 W Warning lights (see Lights) .......10 Washer fluid ..............................
