Table of Contents Introduction Instrument Cluster 4 12 Warning lights and chimes Gauges 12 19 Entertainment Systems 23 AM/FM stereo AM/FM stereo with CD AM/FM stereo with in-dash six CD Auxiliary input jack Satellite radio information Navigation system Family entertainment system Climate Controls Heater only Manual heating and air conditioning Dual automatic temperature control Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjus
Table of Contents Locks and Security 146 Keys Locks Anti-theft system 146 146 159 Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Trailer brake controller-integrated Recreational towing Driving 162 162 170 184 192 204 206 209 224 236 242 246 253 255 Starting Brakes Traction Control™ Transmission operation Snowplowing 255 260 262 265 291
Table of Contents Customer Assistance Reporting safety defects (U.S. only) Reporting safety defects (Canada only) 329 335 336 Cleaning 337 Maintenance and Specifications 346 Hood Engine compartment Engine oil Battery Engine coolant Fuel information Air filter(s) Part numbers Maintenance product specifications and capacities 347 348 351 354 356 362 380 382 383 Accessories 390 Index 392 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle.
Introduction Vehicle Modification Data Recording Some aftermarket products may cause severe engine and/or transmission damage; refer to the What is not covered section in The new vehicle limited warranty for your vehicle chapter of your vehicle’s Warranty Guide for more information.
Introduction Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so. Notice to owners of diesel-powered vehicles Read the 6.0 and 6.
Introduction Use of your Ford light truck as an ambulance, without the Ford Ambulance Preparation Package voids the Ford New Vehicle Limited Warranty and may void the Emissions Warranties. In addition, ambulance usage without the preparation package could cause high underbody temperatures. If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Safety Compliance Certification Label.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Service Engine Soon Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX MIN
Instrument Cluster WARNING LIGHTS AND CHIMES Vehicles equipped with a manual transmission Vehicles equipped with an automatic transmission 12 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)
Instrument Cluster Harley-Davidson vehicles Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains on after starting the vehicle, refer to the respective system warning light description for additional information.
Instrument Cluster Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Instrument Cluster Safety belt: Reminds you to fasten your safety belt. A Belt-Minder威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder威 chime feature. Engine oil pressure: Illuminates when the oil pressure falls below the normal range. Refer to Engine oil in the Maintenance and Specifications chapter. Low tire pressure warning (if equipped): Illuminates when your tire pressure is low.
Instrument Cluster If the light remains on, have the system serviced immediately by your authorized dealer. Refer to Traction Control™ in the Driving chapter for more information Check fuel cap (RTT): Displays when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter.
Instrument Cluster Four wheel drive low (if equipped): Illuminates when four-wheel drive low is engaged. 4x4 LOW Four wheel drive high (if equipped): Illuminates when four-wheel drive high is engaged. 4x4 HIGH Anti-theft: Flashes when the SecuriLock™ Passive Anti-Theft System has been activated. Speed control (if equipped): Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.
Instrument Cluster • Low oil pressure Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF, LOCK or ACCESSORY position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened. Parking brake on warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km).
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed.
Instrument Cluster Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot. Odometer: Registers the total miles (kilometers) of the vehicle.
Instrument Cluster Standard instrument cluster Harley-Davidson instrument cluster Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked at your authorized dealer.
Instrument Cluster Battery voltage gauge (manual transmission only): Indicates the battery voltage when the ignition is in the RUN position. If the pointer moves and stays outside the normal operating range, have the vehicle’s electrical system checked as soon as possible. Transmission fluid temperature gauge (automatic transmission only): If the gauge is in the: Normal area (normal) - the transmission fluid is within the normal operating temperature (between “H” and “C”).
Entertainment Systems AUDIO SYSTEMS AM/FM stereo system (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.
Entertainment Systems 2. AUDIO: Press AUDIO repeatedly to gain access to the following settings: TREB (Treble): Press AUDIO to reach the treble setting. Use / / SEEK . BASS (Bass): Press AUDIO to reach the bass setting. Use SEEK / / . BAL (Balance): Press AUDIO to reach the balance setting. / / SEEK to adjust between the left and right Use speakers. Setting the clock: Press and hold CLK until the hours start to flash, / / SEEK to adjust.
Entertainment Systems AM/FM stereo single CD/satellite compatible sound system (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.
Entertainment Systems 2. (Phone): Pressing (Phone) results in “NO PHONE” message shown in display. 3. MENU: Press MENU repeatedly to access to the following settings: Setting the clock: Press MENU until SET HOUR or SET MINUTES is / / SEEK, SEEK to adjust the displayed. Use hours/minutes. CATEGORY (satellite radio, if equipped - early availability): Press MENU until the currently active category appears in the display / to scroll (CATEGORY MODE).
Entertainment Systems • SAVE SONG: Press OK to save the currently playing song title in the system’s memory. (If you try to save something other than a song, CANT SAVE will appear in the display.) When the chosen song is playing on any satellite radio channel, the system will alert you with an audible prompt. Press OK while SONG ALERT is in the display and the system will take you to the channel playing the desired song. You can save up to 20 song titles.
Entertainment Systems AUTOSET: Press MENU until the display reads AUTOSET. Autoset allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2. Use / / SEEK, SEEK to turn on/off. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. BASS: Press MENU to reach the bass setting.
Entertainment Systems COMPRESS (Compression): Available only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display. Use / / SEEK, SEEK to toggle ON/OFF. When COMPRESS is ON, the system will bring the soft and loud CD passages together for a more consistent listening level. 4. AUX: Press repeatedly to cycle through FES/DVD (if equipped), LINE IN (auxiliary audio mode, if equipped) and SAT1, SAT2 and SAT3 modes (satellite radio, if equipped).
Entertainment Systems 7. SHUFFLE: In CD/MP3 mode, press SHUFFLE to engage shuffle mode. SHUFFLE ON will appear in the display. If you wish to engage shuffle mode right away, press SEEK to begin random play. Otherwise, random play will begin when the current track is finished playing. CD SHUF will appear in the display. To disengage, press SHUFFLE again. SHUFFLE OFF will appear in the display. Note: In CD/MP3 mode, press SHUFFLE to play the tracks in random order.
Entertainment Systems In satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE, press again to scroll through the current song title, artist, channel category and the SIRIUS long channel name. In TEXT MODE sometimes the display requires additional text to be to view the displayed. When the “>” indicator is active, press SEEK SEEK additional display text. When the “<” indicator is active, press to view the previous display text.
Entertainment Systems Premium/Audiophile in-dash six CD/MP3/satellite compatible sound system (if equipped) Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.
Entertainment Systems Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability. 2. (Phone): Pressing (Phone) results in “NO PHONE” message shown in display. 3. MENU: Press repeatedly to access to the following settings: Setting the clock: Press until SELECT HOUR or SELECT MINS is displayed. Press / / SEEK to adjust the hours/minutes.
Entertainment Systems • SAVE SONG: Press OK to save the currently playing song title in the system’s memory. (If you try to save something other than a song, CANT SAVE will appear in the display.) When the chosen song is playing on any satellite radio channel, the system will alert you with an audible prompt. Press OK while SONG ALERT is in the display and the system will take you to the channel playing the desired song. You can save up to 20 song titles.
Entertainment Systems When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. RBDS: Available only in FM mode. This feature allows you to search RBDS-equipped stations for a certain category of music format: CLASSIC, COUNTRY, INFORM, JAZZ/RB, ROCK, etc. To activate, press MENU repeatedly until RBDS (ON/OFF) appears in the display. Use / / SEEK to toggle RBDS ON/OFF.
Entertainment Systems The default setting is off; increasing your vehicle speed will not change the volume level. Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly with vehicle speed to compensate for road and wind noise. Recommended level is1–3; SPEED OFF turns the feature off and level 7 is the maximum setting. Track/Folder Mode: Available only on MP3 discs in CD mode.
Entertainment Systems In TEXT MODE, press SEEK, SEEK to view the previous/additional display text. SEEK, SEEK to select a In CATEGORY MODE, press category. Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability. / OK (Play/Pause): This 6. control is operational in CD/MP3 mode. When a CD/MP3 is playing, press to pause or play the current CD. The CD status will display in the radio display. OK: Use in various menu selections.
Entertainment Systems 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: To set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset control until sound returns. You may store up to six stations in each frequency band for a total of 18. In satellite radio mode (if equipped), there are 18 available presets, six each for SAT1, SAT2 and SAT3.
Entertainment Systems 15. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. Note: If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 16. CD: Press to enter CD/MP3 mode. If a CD/MP3 is already loaded into the system, CD/MP3 play will begin where it ended last. 17. LOAD: To load a disc into the system, press LOAD. Select a slot number using memory presets 1–6.
Entertainment Systems 19. CD slot: Insert a CD/MP3 label side up. Auxiliary input jack (if equipped) Your vehicle may be equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack, located on the instrument panel below the power point, provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity.
Entertainment Systems Troubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ. The AIJ will only work correctly with devices that have a headphone output with a volume control. 2. Do not set the portable music player’s volume level higher than is necessary to match the volume of the CD or FM radio in your audio system as this will cause distortion and will reduce sound quality.
Entertainment Systems CD/CD player care Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. • Wipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to only play commercially manufactured, round (4.
Entertainment Systems CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio system warranty and service Refer to the Warranty Guide for audio system warranty information.
Entertainment Systems Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played. Other files will be ignored by the system. This enables you to use the same MP3 disc for a variety of tasks on your work computer, home computer and your in vehicle system. 1 .mp3 1 .mp3 2 2 .mp3 3 3 .mp3 4 .
Entertainment Systems • Terrain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower, a stronger signal may overtake a weaker one and result in an audio mute. Unlike AM/FM audible static, you will hear an audio mute when there is a satellite radio signal interference.
Entertainment Systems Radio Display ACQUIRING SAT FAULT INVALID CHNL UNSUBSCRIBED NO TEXT Condition Action Required Radio requires more No action required. than two seconds to This message should produce audio for the disappear shortly. selected channel. Internal module or If this message does system failure not clear within a short present. period of time, or with an ignition key cycle, your receiver may have a fault. See your authorized dealer for service. Channel no longer This previously available.
Entertainment Systems Radio Display NO TEXT NO TEXT NO SIGNAL UPDATING CALL SIRIUS 1–888–539–7474 Condition Song title information not available. Action Required Song title information not available at this time on this channel. The system is working properly. Category information Category information not available. not available at this time on this channel. The system is working properly.
Entertainment Systems FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.
Entertainment Systems Press VIDEO to change the source displayed on the screen. Press repeatedly to cycle through: DVD-DISC, DVD-AUX, NON-DVD, OFF. Press the power button to turn the system off. The indicator light will turn off indicating the system is off. Note: The audio from the DVD system will play over all vehicle speakers and can be adjusted by the radio volume control. To play a CD in the DVD system: The DVD system can play audio CDs, CD-R and CD-R/W, CD-ROM and video CDs.
Entertainment Systems 2. Insert an MP3 disc into the system, label-side up to turn on the DVD system. It will load and automatically begin to play. If there is already a disc in the system, press PLAY on the DVD player. 3. The disc will begin to play and the ’MP3 Audio Disc’ screen will display and allow you to access the COMPRESSION, SHUFFLE, SCAN and FOLDER MODE features.
Entertainment Systems from the auxiliary source, the screen will remain black. If the video source is set to DVD-AUX, the display will automatically turn on if a video signal is detected. To listen to audio over the headphones (Dual play mode): 1. You may listen to channels A and B over wired or wireless headphones. Refer to Using the infrared wireless headphones and Using wired headphones for further information. • Black (4) — wired headphone output (wired headphones not included) 2.
Entertainment Systems 2. Adjust the volume levels using the volume controls on the DVD system. To adjust display brightness: To decrease/increase the brightness level on the display screen, press the brightness control on the DVD system. A display will appear at the bottom of the screen indicating the brightness level. The brightness display will only appear when the menu is not displayed.
Entertainment Systems Note: Headphone A can access any possible media (AM, FM1, FM2, SAT (if equipped), CD, DVD, DVD-AUX). Headphone B can only access DVD and DVD-AUX. For further information, refer to Single play/Dual play later in this section. 2. / (Stop/Eject): Press once to stop and press a second time to eject a disc from the DVD system. (Reverse): Press and 3. release for the previous chapter or track. Press and hold to reverse search a DVD, Video CD, or FES CD in DVD/CD mode.
Entertainment Systems 9. LCD screen: The eight inch diagonal screen rotates down to view and up into housing to store when not in use. Ensure that the screen is latched into the housing when being stored. 10. Volume: When in Single Play, ) or decrease press to increase ( ( ) the volume over all speakers. When in Dual Play, press to increase ) or decrease ( ) the volume ( for the wired headphones. (Wireless headphone volume is controlled with the rotary dial on the right ear piece.
Entertainment Systems 15. ENTER: Press to select/confirm the current selection. 16. Cursor /Brightness controls: Use the cursor controls to make various selections when in any menu. When not in a menu, and in / to adjust DVD mode, press the brightness. A display bar will appear at the bottom of the screen indicating the brightness levels. Remote control Unless otherwise stated, all operations can be carried out with the remote control. Always point the remote control directly at the player.
Entertainment Systems 3. DISPLAY: Press to access the on-screen display of the FES functions and adjustments. 4. RETURN: Press to return to the previous menu screen. 5. ANGLE (DVD dependent): Press to select the angle to view the scene. 6. Channel A/B: Press to select either A or B headphones and then use the MEDIA control to select the desired playing media for the headphones. 7. VOL (Volume): When in Single Play, press to increase ( ) or ) the volume over all speakers.
Entertainment Systems 18. Fast reverse/Previous: When a DVD is playing, press and hold for a quick reverse within the DVD. Press and release for the previous chapter. Press PLAY to resume normal playback speed and volume. In CD/MP3 mode, press to access the previous track. 19. MENU: Press to access the DVD disc menu for selections. Press MENU again when in the DVD disc menu to access the system set-up menu. 20. SUBTITLE (DVD dependent): Press to turn the subtitle feature ON or OFF. 21.
Entertainment Systems Remove the screw and unlatch the battery cover to access the batteries. The remote control unit uses two AAA batteries which are supplied with the unit. Headphones Wireless headphones The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens, which could result in a crash causing serious injury. Give your full attention to driving and to the road.
Entertainment Systems To install the batteries, remove the screw at the bottom of the cover. Then, lightly press down on top and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct orientation as indicated in the battery housing.
Entertainment Systems To operate the headphones: • Press POWER on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press POWER again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment. • Select the desired audio source (Channel A or B) for each set of wireless headphones by using the A/B selection switch on the ear piece. • Adjust the volume control to the desired listening level.
Entertainment Systems Wired headphones Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. The driver should never use the headphones while driving the vehicle. Using headphones may prevent the driver from hearing audible warnings such as horns or emergency sirens, which could result in a crash causing serious injury.
Entertainment Systems Single Play: Single play consists of all occupants in the vehicle listening to the same playing media over the front and rear speakers. When the DVD system is on, and the same source is playing through the front and rear speakers, SINGLE PLAY will appear in the front radio display. Dual Play: Dual play is when the rear seat passengers choose to listen to a different playing media than the front seat passengers.
Entertainment Systems Operation with an aftermarket audio system (Headphone only mode) When the Family Entertainment System (FES) detects that the original radio supplied by Ford Motor Company has been removed from the vehicle, the Family Entertainment System will work in a state referred to as “Headphone Only Mode”. While operating in Headphone Only Mode, the system will have limited functionality. • The system will only output audio to the headphones.
Entertainment Systems This is disc dependent — some DVD discs may have more viewing angles to select from. Once you have made your selection, press ENTER to confirm. The system default is Angle 1. Aspect ratio Select ASPECT RATIO to select the viewing size and shape of the video displayed on the LCD screen. This is disc dependent. You can select from: WIDE, LETTER BOX or PAN SCAN. Once you have made your selection, press ENTER to confirm.
Entertainment Systems Once you have made your selection, press ENTER to confirm. The system default is English. Subtitles Select SUBTITLES to turn the subtitle option on or off. The system default is OFF. Once you have made your selection, press ENTER to confirm. This is disc dependent. Audio CDs To play audio CDs on your DVD system: 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Ensure that the DVD system is ON. 3. Insert an audio CD into the DVD system, label side up. 4.
Entertainment Systems COMP (Compression): Compression brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press to turn the feature on/off. SHUFFLE: Press to hear all tracks on the current CD in random order. Press again to stop. SCAN: Press for a brief sampling of all tracks on the current CD. Press again to stop. Playing MP3 discs To play an MP3 disc on your DVD system: 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2.
Entertainment Systems • Bit rate — The player supports bit rates from 32–320 kbps, as well as variable bit rate MP3 files, but lower bit rates will have a noticeable effect on sound quality and are recommended only for speech or low fidelity music material. We recommend that you encode MP3 files using a high quality encoder. • PC configuration — Encoding MP3 files requires intensive use of your computer’s resources. Follow the PC configuration recommendations of the encoder software vendor.
Entertainment Systems CDs or DVDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs or DVDs. Please contact your authorized dealer for further information. Playing a DVD 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Ensure that the navigation system is on. 3. Insert a DVD label-side up into the system. 4. Use the DVD bezel controls to: Press to play or pause a DVD. Press to stop or eject a DVD.
Entertainment Systems Frame by frame 1. With a DVD playing, press pause. 2. Press the right cursor button. The DVD will advance one frame. Each press of the right cursor button will advance the DVD video by one frame. Headphone/auxiliary jacks There are wired headphones (not included) and auxiliary jacks on the left and right side of your DVD system.
Entertainment Systems Audio displays Your DVD system interacts closely with the front audio system. Status messages will appear in the radio display showing the DVD status. Some possible radio display messages: • SINGLE PLAY or DUAL PLAY • DVD LOAD • DVD MENU • DVD STOP Audio interaction You can then also use the front audio controls to advance, reverse, play and pause a DVD. While a DVD is playing you may use the following controls on the front radio: • SEEK: Press to advance to the previous ( chapters.
Entertainment Systems When the DVD system is ON, you 1 2 3 4 5 can then press the memory preset controls 2 and 4 simultaneously to toggle between Single Play and Dual Play. In Single Play mode, all speakers listen to the same media. In Dual Play mode, rear seat passengers can use the infrared wireless, or wired (not included) headphones to listen to a different playing media than the front seat passengers. 6 General information Note: DVDs are formatted by regions.
Entertainment Systems Safety information Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.
Entertainment Systems Do not operate video games or video equipment if the power cords and/or cables are broken, split or damaged. Carefully place cords and/or cables where they will not be stepped on or interfere with the operation of seats and/or compartments. Disconnect video games and video equipment power cords and/or cables when not in use. Avoid touching auxiliary input jacks with your fingers. Do not blow on them or allow them to get wet or dirty.
Entertainment Systems Temperature extremes When the vehicle is parked under direct sunlight or in an extremely cold place for a long period of time, wait until the cabin temperature of the vehicle is at normal temperature before operating the system. Humidity and moisture condensation Moisture in the air will condense in the DVD player under extremely humid conditions or when moving from a cold place to a warm one. Moisture condensation may cause damage to the DVD and/or player.
Entertainment Systems While operating in Headphone Only Mode, the system will have limited functionality. • The system will only output audio to the headphones. It will not be capable of providing audio to the speakers. • The available sources in FES Headphone Only Mode are DVD-DISC and DVD-AUX, regardless of headphone channel (A or B). • When a disc is inserted into the FES while in Headphone Only Mode, both headphone channels (A and B) will be connected to FES-DISC.
Climate Controls HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control: : Distributes outside air through the instrument panel vents. : Distributes outside air through the instrument panel vents and the floor vents.
Climate Controls To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
Climate Controls 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to cool the vehicle. This re-cooling of the interior air is more economical and efficient.
Climate Controls Operating tips • To reduce fog build up on the windshield during humid weather, place position. the air flow selector in the • To reduce humidity build up inside the vehicle, do not drive with the air flow selector in the O (OFF) position. • Do not put objects under the front seats that will interfere with the airflow to the rear seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield.
Climate Controls DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMS (IF EQUIPPED) • DATC • DATC with heated mirrors 80 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)
Climate Controls • DATC with heated seats and heated mirrors Temperature conversion: To switch between Fahrenheit and Celsius, refer to Units (English/Metric) under either Standard Message Center or Optional Message Center in the Driver Controls chapter , A/C, , In order to achieve maximum cooling performance, press and set the temperature to 60°F (16°C) and the highest blower setting. Defrost: Distributes outside air through the windshield defroster 1. and demister vents.
Climate Controls 4. Recirculation control: Press to activate/deactivate air recirculation in cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculation can be (defrost). engaged manually in any other airflow selection except Recirculation may turn off automatically in all airflow selections except MAX A/C. 5. A/C control: Press to activate/deactivate air conditioning.
Climate Controls Operating tips • To reduce fog build up on the windshield during humid weather, place position. the air flow selector in the • To reduce humidity build up inside the vehicle, do not drive with the engaged and A/C off. system OFF, or with recirculated air • Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield.
Climate Controls To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Lights Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position, • the headlamp control is in the and (OFF) or parking lamp position • the parking brake must be disengaged. Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions.
Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable illuminated switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full Dome/ON position to reset.
Lights To adjust the headlamps: 1. Park your vehicle on a level surface about 25 feet (7.6 meters) away from a vertical plain surface (3). Check your headlamp alignment at night or in a dark area so that you can see the headlamp beam pattern. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line • (5) Center of headlamps • (6) Center line of the vehicle 2.
Lights 5. Locate the vertical adjuster (2) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down). 6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen. 7. On the wall or screen, locate the high intensity area of the beam pattern.
Lights • (4) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover one of the headlamps so no light from that lamp hits the wall. 4.
Lights MAP LAMPS (IF EQUIPPED) The dome lamp turns on when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is OFF. BULBS Headlamp condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation.
Lights Function Number of bulbs 2 2 2 2 2 5 Trade number Foglamp 9145 License plate lamp 194 Cargo lamp 906 Mirror turn signal 2825 Mirror clearance lamp 2825 Front clearance lamps (2) and Front 194 identification lamps (3) Rear fender clearance* 4 W5W Interior visor lamp (if equipped) 4 194 Rear identification 3 194 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer * Dual rear wheels, or if equipped.
Lights 5. Remove the bulb assembly by turning it counterclockwise and pulling it straight out. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb(s) in reverse order. Replacing park/turn and sidemarker lamp bulbs (aerodynamic) 1.
Lights 4. Remove the bulb assembly, (1) sidemarker or (2) park/turn by turning it counterclockwise and pulling it straight out. 5. Pull the old bulb out from the socket. Install the new bulb(s) in reverse order. Replacing headlamp bulbs (sealed beam) 1. Make sure that the headlamp control is in the off position and open the hood. 2. Remove the three screws and one bolt from the top and bottom of the park lamp/bezel assembly. 3. Remove the four screws and the headlamp retaining ring from headlamp. 4.
Lights 2. Remove the three screws and one bolt from the top and bottom of the park lamp/bezel assembly. 3. Pull the assembly straight out disengaging snap clip. 4. Remove the bulb assembly, sidemarker or park/turn by turning it counterclockwise. (Top view of assembly shown.) 5. Pull the old bulb out from the socket. Install the new bulb(s) in reverse order. Replacing brake/tail/turn/back-up lamp bulbs - Pick-ups only 1.
Lights 3. Rotate the bulb socket counterclockwise and remove from lamp assembly. 4. Pull the bulb straight out of the socket. Install the new bulb(s) in reverse order. Replacing brake/tail/turn/back-up lamp bulbs - Chassis cabs only; if equipped 1. Make sure the headlamp switch is in the off position. 2. Remove the four screws and the lamp lens from lamp assembly. 3. Carefully pull the bulb straight out of the socket and push in the new bulb. Replacing cargo lamp and high-mount brakelamp bulbs 1.
Lights Front clearance and identification lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Remove the screw and lens from the lamp assembly. 3. Pull the bulb straight out of the socket. Install the bulb(s) in reverse order. Replacing foglamp bulbs (if equipped) 1. Make sure the headlamp switch is in the OFF position. 2. Remove the bulb socket from the foglamp by turning counterclockwise. 3. Disconnect the electrical connector from the foglamp bulb.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls TILT STEERING WHEEL (IF EQUIPPED) 1. Pull and hold the steering wheel release control toward you. 2. Move the steering up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering column when the vehicle is moving. TRANSMISSION CONTROL Tow/Haul feature (5–speed automatic transmission) (if equipped) To activate, press the transmission control switch (TCS) located on the gearshift.
Driver Controls ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. If your vehicle is equipped with a moon roof, refer to One-touch moonroof later in this chapter for information on its operation. Storage compartment (if equipped) Press the release on the door to open the storage compartment.
Driver Controls The auxiliary power point is located on the instrument panel. On SuperCab and Crew Cab models, another power point is located on the rear of the center console (if equipped). Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W.
Driver Controls POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the window switches to open and close windows. • Push down (to the first detent) and hold the switch to open.
Driver Controls When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. If your vehicle is equipped with a power rear slide window, the switch is located on the instrument panel behind the right-hand side of the steering wheel. • Press the right side of the control to open the window. • Pull the right side of the control to close the window.
Driver Controls Automatic dimming inside rear view mirror (if equipped) Your vehicle may be equipped with an inside rear view mirror which has an auto-dimming function. The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare.
Driver Controls Heated outside mirrors (if equipped) The main mirror glass is heated to remove ice, mist and fog. To activate the heated mirrors, press the heated ) located on mirror control ( the climate control panel. The heated mirrors will operate for 10 minutes, then automatically shut off (or shut off when the engine is turned off). In cases of extreme ice and cold, the heater control may need pressing again after 10 minutes in order to fully clear the glass.
Driver Controls Powerfold mirror positions, from left to right: Position 1, Position 2, Position 3 The powerfold mirrors may be folded forward/rearward manually to any of the three positions shown and electrically to positions 1 and 2 only. If a mirror is folded manually forward to position 3, you must manually fold it back to position 1 or 2 in order for the powerfold function to continue functioning.
Driver Controls Note: If the power fold/telescope mirror glass appears loose or vibrates when driving, it is possible that the mirrors have been manually folded or telescoped. To minimize the vibration, ensure that the mirrors are electronically folded and telescoped in/out with the switches on the door trim panel. Telescoping mirrors (if equipped) The telescoping feature allows the mirror to extend approximately 2.75 inches (70 mm). This feature is especially useful to the driver when towing a trailer.
Driver Controls Mirror mounted side turn signal indicator (if equipped) When the vehicle turn signals are activated, the outer portion of the mirror housing will blink amber. The turn signal feature can be seen by other drivers who may approach from the rear of the vehicle. Clearance lamps (if equipped) Illuminates when the headlamps or parking lamps are switched on. This provides additional visibility of your vehicle to other drivers on the road.
Driver Controls Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The accelerator and brake pedal positions are saved when doing a memory set function and can be recalled along with the vehicle personality features when a memory position is selected through the remote entry transmitter, keyless entry keypad or memory switch on the driver’s door (if equipped with memory feature).
Driver Controls Note: • Vehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed. • If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed.
Driver Controls Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h). • Depress the brake pedal until the desired vehicle speed is reached, press the SET + control.
Driver Controls STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use cell phones and other devices not essential to the driving task when it is safe to do so.
Driver Controls In any mode: • Press VOL + or − to adjust volume. Climate control features (if equipped) Press TEMP + or - to adjust temperature. Press FAN + or - to adjust fan speed.
Driver Controls UPFITTER CONTROLS (IF EQUIPPED) Your vehicle may be equipped with the Upfitter option package which will provide four switches, mounted in the center of the instrument panel, labeled AUX 1, AUX 2, AUX 3 and AUX 4. These switches will only operate while the ignition is in the 3 (ON) position, whether the engine is running or not. It is, however, recommended that the engine remain running to maintain battery charge when using the Upfitter switches for extended duration or higher current draws.
Driver Controls There will also be one power lead for each switch found as a blunt-cut and sealed wire located below the instrument panel and to the left of the steering column. They are coded as follows: Switch AUX 1 AUX 2 AUX 3 AUX 4 Circuit number Wire color CAC05 Yellow CAC06 Green with Brown Trace CAC07 Violet with Green Trace CAC08 Brown Fuse 30A 30A 10A 15A More detailed information about the Upfitter switches can be found in the Upfitter Switches bulletin found at www.fleet.ford.
Driver Controls To close the moon roof: Press and hold the control until the glass panel stops at the “comfort” position. Press and hold the control again until the glass stops moving (the moon roof does not go to the comfort position). When fully closed, the rear portion of the glass panel will appear higher than the front portion. control. The moon To vent the moon roof: Press and hold the roof must be in the closed position in order to move it into the vent position.
Driver Controls model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase).
Driver Controls 6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6.
Driver Controls Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.
Driver Controls CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with cassette/CD holder • Coin holder • Pen holder • Writing surface • A power point inside and on the rear • Laptop storage • Hanging file folder supports • Rear cupholders (Crew Cab only) Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Driver Controls Selectable features Press and release the SELECT/RESET control switch, located in the speedometer, to scroll and reset the following functions. Select or reset the function by holding the SELECT/RESET button for more than 2 seconds.
Driver Controls Average fuel economy (AFE) Select this function to display your average fuel economy in miles/gallon or liters/km.
Driver Controls Units (English/Metric) 1. Select this function from the SETUP MENU for the current units to be displayed. 2. Press and hold the SELECT/RESET control switch to change from English to Metric. 3. Press the SELECT/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Language Note: When entering the SETUP MENU and a non-English language has been selected, “PRESS RESET FOR ENGLISH” will be displayed to change back to English. 1.
Driver Controls 5. BRAKE SYSTEM 6. FUEL LEVEL 7. TRAILER DISCONNECTED (if equipped) System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages.
Driver Controls Warning display Status Low tire pressure (if equipped) Warning can be cleared by pressing the RESET button. Warning can Tire Monitor Fault (if reappear if the condition is still equipped) present. Warning will reappear on the Tire Sensor Fault (if equipped) next ignition key-cycle if the condition still exists.
Driver Controls CHECK BRAKE SYSTEM Displayed when a fault has been detected by the ABS module. DRIVER DOOR AJAR Displayed when the driver’s door is not completely closed. PASSENGER DOOR AJAR Displayed when the passenger’s door is not completely closed. REAR LEFT DOOR AJAR Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR Displayed when the rear right door is not completely closed. LOW FUEL LEVEL Displayed as an early reminder of a low fuel condition.
Driver Controls TIRE PRESSURE SENSOR FAULT (if equipped): Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. CHECK AIR FILTER (Diesel engine only): Refer to Instrument Cluster in your 6.
Driver Controls OK TO DRIVE (Diesel engine only). Displayed when the time counter has reached 0 (zero) and the engine is sufficiently warm enough to drive in extremely cold weather (refer to the ENGINE WARMING description mentioned previously). DRIVE TO CLEAN EXHAUST SYSTEM (Diesel engine only). Displayed when the engine control module detects the Diesel particulate filter (DPF) is full of particulates and that the vehicle is not being operated in a manner to allow automatic cleaning.
Driver Controls OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the RUN position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by an indicator chime.
Driver Controls Info menu This control displays the following control displays: • Trip Odometer A or B • Distance to Empty • Average Fuel Economy • Drive Time (Elapsed Travel Timer) • Blank (Odometer and compass, if equipped, off) RESET SETUP INFO Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions.
Driver Controls If you calculate your average fuel economy by dividing miles traveled since last fill-up by gallons of fuel used (multiply liters used by 100, then divide by kilometers traveled), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at service stations • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the ne
Driver Controls • Reset to English (if in another language) (see Note below) Note: When returning to the SETUP menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed to change back to English. Press and hold the RESET control to change back to English. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored.
Driver Controls Autolamp timer presets This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds. Autolocks This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1.
Driver Controls Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 3 2 2. Turn ignition to the RUN position. 3. Start the engine. 4 1 15 14 13 5 12 6 7 8 9 1011 4. From the SETUP menu, press and release the RESET control until the message center display changes to show the current zone setting (XX). 5. Press and release the RESET control repeatedly until the correct zone setting for your geographic location is displayed on the message center.
Driver Controls 9. The compass is now calibrated. Note: If the RESET control is pressed or 3 minutes has expired, the display will go back to the INFO menu and will show CAL instead of the compass heading until the compass is calibrated. Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Waiting 4 seconds or pressing the RESET control cycles the message center through each of the language choices. Selectable languages are English, Spanish, or French. 3.
Driver Controls This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Park brake engaged Check brake system Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar Low fuel level Trailer fault (if equipped) TBC fault (if equipped) Trailer disconnected (if equipped) Low brake fluid level Low tire pressure (if equipped) Status Warning returns after 10 minutes if condition still exists.
Driver Controls Warning display Check air filter (diesel engine only) Drain water separator (diesel engine only) Stop safely now (diesel engine only) Engine warming please wait xx(diesel engine only) OK to drive (diesel engine only) Engine turns off in xx (diesel engine only) Engine turned off (diesel engine only) Drive to clean exhaust system (diesel engine only) Cleaning exhaust filter (diesel engine only) Exhaust filter drive complete (diesel engine only) Oil change required/Engine oil change soon (diese
Driver Controls REAR LEFT DOOR AJAR. Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR. Displayed when the rear right door is not completely closed. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition. TRAILER FAULT (if equipped). Displayed if there is a short circuit on the electric brake output wire or the trailer brakes are drawing too much current. Refer to Integrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.
Driver Controls DRAIN WATER SEPARATOR (Diesel engine only). Displayed when the water separator has reached a predetermined capacity and needs to be drained. Refer to your 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for more information. STOP SAFELY NOW (Diesel engine only). Displayed when the vehicle exhaust system temperature exceeds intended operating range.
Driver Controls CLEANING EXHAUST FILTER (Diesel engine only). Displays briefly when the vehicle has entered the cleaning mode normally; or, displays continuously when cleaning the filter after a DRIVE TO CLEAN EXHAUST SYSTEM message was previously displayed. This message is NORMAL. EXHAUST FILTER DRIVE COMPLETE (Diesel engine only). Displayed when the vehicle has completed the adequate drive cycle to clean the DPF. This message is NORMAL. OIL CHANGE REQUIRED/ENGINE OIL CHANGE SOON (Diesel engine only).
Driver Controls 1. Before removal of the tailgate, locate and disconnect the electrical connector under the pick-up box on the right-hand side of the vehicle near the spare tire. 2. Install the protective cap (tethered to the wiring harness under the vehicle) on the RCS connector. 3. Carefully bring the wiring harness up between the pick-up box and the bumper. Secure the tailgate harness onto the pick-up box. 4. Lower the tailgate. 5.
Driver Controls 3. Rotate the center molding to unlatch the tailgate. 4. Flip open the panel to widen the step. Note: To reduce risk of falling: • Operate step only when the vehicle is on level surface. • Operate step only in areas with sufficient lighting • Always open flip panel to widen step. • Always use grab handle when stepping up and down. • Step not intended for bare-footed use. • Keep step clean from contamination before use (e.g. snow, mud) • Keep the step load (you + load) below 350 lb. (159 kg).
Driver Controls To open the bed extender into Tailgate Mode: 1. Pull the locking pin toward the center of the vehicle. 2. Rotate the storage hinge rearward to unlatch the panels. 3. Rotate the panels toward the tailgate. Repeat Steps 1–3 for the other side of the bed extender.
Driver Controls 4. Connect the two panels, then rotate both knobs a quarter-turn clockwise to secure the panels. 5. Ensure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box. 6. Reverse steps for storage of the bed extender. Note: When the vehicle is in motion, ensure the locking pins and knobs are fully engaged. Note: Ensure all cargo is secured. Note: When the vehicle is in motion, the tailgate load must not exceed 150 lbs.
Driver Controls To open the bed extender into Grocery Mode, follow Steps 1–5 by rotating the panels away from the tailgate.
Locks and Security KEYS The key operates all locks on your vehicle. You should always carry a second key with you in a safe place in case you require it in an emergency. If your vehicle is equipped with the SecuriLock™ Passive Anti-theft system, your keys are coded to your vehicle; using a non-coded key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer. POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors.
Locks and Security Autolock feature (if equipped) The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h) for greater than 2 seconds.
Locks and Security 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (ON) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the 1 (OFF/LOCK) position.
Locks and Security Deactivating/activating autounlock feature There are three methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock sequence, • using a keypad procedure (if equipped) Note: The autounlock feature can be activated/deactivated independently of the autolock feature. Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the 1 (OFF/LOCK) position and all vehicle doors are closed.
Locks and Security Keyless entry key pad autounlock enable/disable procedure 1. Turn the ignition to the 1 (OFF/LOCK) position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second time. 5. Release the 3 • 4.
Locks and Security REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Locks and Security One step door unlocking If the one step door unlocking feature is activated, press and release once to unlock all of the doors. Note: The interior lamps will illuminate (refer to the Illuminated entry feature later in this section) if the control on the overhead lamp is not set to the off position. Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled.
Locks and Security Activating the memory seat feature To activate this feature: 1. Position the seat, adjustable pedals and mirrors to the position desired. 2. Press the SET control on the driver’s door panel. 3. Within five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the lower-center portion of the instrument panel which you would like to associate with the seat and Driver 1 or Driver 2 positions. 4.
Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together.
Locks and Security To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and 3 (ON). Note: The eighth turn must end in the 3 (ON) position. The doors will lock, then unlock, to confirm that the programming mode has been activated. 4. Within 20 seconds press any button on the remote entry transmitter.
Locks and Security Deactivating/activating perimeter lamps illuminated entry You may enable/disable this feature by having your vehicle serviced by your authorized dealer. You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition is in the 1 (OFF/LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated.
Locks and Security • the 7 • 8 and the 9 • 0 controls on the keyless entry keypad are pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open.
Locks and Security • Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting. Note: The factory-set code cannot be associated with a memory setting. 5. The doors will again lock then unlock to confirm that your personal keycode has been programmed to the module. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order.
Locks and Security SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock™ passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer.
Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (OFF/LOCK) position. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed.
Locks and Security 1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in the 3 (ON) position for at least one second, but no more than ten seconds). 2. Turn ignition from the 3 (ON) position back to the 1 (OFF/LOCK) position in order to remove the first coded key from the ignition. 3.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Adjustable head restraints (if equipped) The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Seating and Safety Restraints To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion. Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place.
Seating and Safety Restraints 40/20/40 split bench seat (if equipped) • Lift the track release bar to move the seat forward or backward. Ensure the seat is relatched into place. • Pull the handle on the side of the seat up to recline the seat. • Push down the lever located at the bottom of the seatback to quickly fold the seatback forward. 40/20/40 front seat armrest and console (if equipped) To release the armrest, pull forward on the strap and pull the armrest down.
Seating and Safety Restraints Lift up armrest to return it to a center seatback. Captain’s chair (if equipped) • Lift the bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • To recline the seatback, pull the release lever handle located on the side of the seat up. • Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward.
Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Seating and Safety Restraints Using the manual lumbar support The lumbar support control is located on the outboard side of the seat Turn the lumbar support clockwise for more support. Turn the lumbar support counterclockwise for less support. Heated seats (if equipped) The heated seat control is located on the climate control panel.
Seating and Safety Restraints Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, power mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the driver door. • To program position 1, move the driver seat, mirrors and pedals (if equipped) to the desired position using the associated controls. Press the SET control. The SET control indicator light will briefly illuminate.
Seating and Safety Restraints To fold the seatback down, pull down the latch lever located on the bottom seat back to fold the seat back forward. To flip the seat cushion up, pull up on the lever located on the side of the seat cushion to rotate the cushion up until it locks into a vertical storage position, gaining access to the grocery hook located on the underside of the driver-side seat cushion. The maximum load is 25 lb. (11 kg).
Seating and Safety Restraints To gain access to the cupholders and tray, pull down on the armrest. To gain access to the 60/40 load floor, store the cushion in the upright locked position. Pull up on the straps located at the sides of the load floor, and rotate forward until resting on the carpet. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle.
Seating and Safety Restraints This mode should be used any time a child safety seat is installed except a booster in a front or rear outboard passenger seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter. How to use the automatic locking mode • Buckle the combination lap and shoulder belt.
Seating and Safety Restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in the Workshop Manual. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
Seating and Safety Restraints Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. To adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place.
Seating and Safety Restraints 2. Insert the belt into the clip on the back panel. Protect the stowed belt if you carry cargo this may damage or soil the belt. If the belt has been disconnected to carry large objects behind the seat, reconnect it as follows: 1. Remove the belt from the stowage clip on the back panel. 2. Buckle the small tongue on the end of the belt into the mini-buckle on the driver’s side. The belt is now ready for use.
Seating and Safety Restraints longer. The cinch tongue is designed to slip during a crash, so always wear the shoulder belt properly and don’t allow any slack in either the lap or shoulder portions. Before you can reach and latch a combination lap and shoulder belt having a cinch tongue into the buckle, you may have to lengthen the lap belt portion of it. 1. To lengthen the lap belt, pull some webbing out of the shoulder belt retractor. 2.
Seating and Safety Restraints Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. • 1st row center seating position on SuperCab and Crew Cab The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers.
Seating and Safety Restraints Reasons given... “I have an airbag” “I’d rather be thrown clear” Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. Do not sit on tope of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder威 chime.
Seating and Safety Restraints While the design allows you to deactivate your Belt-Minder威, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the Belt-Minder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the Belt-Minder威 feature while driving the vehicle. Belt-Minder威 activation and deactivation procedure 1. Turn the ignition switch to the RUN (or ON) position.
Seating and Safety Restraints Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided.
Seating and Safety Restraints Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module.
Seating and Safety Restraints An infant in a rear-facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned off. See Passenger airbag ON/OFF switch. How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration.
Seating and Safety Restraints restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately.
Seating and Safety Restraints Disposal of airbags and airbag equipped vehicles See your local authorized dealer. Airbags MUST BE disposed of by qualified personnel. Passenger airbag ON/OFF switch (if equipped) An airbag ON/OFF switch (if equipped) may be installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings.
Seating and Safety Restraints An infant in a rear-facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unless the passenger airbag is turned off. Turning the passenger airbag back on The passenger airbag remains OFF until you turn it back ON. 1. Insert the ignition key and turn the switch to ON. 2. The OFF light will briefly illuminate when the ignition is turned to On.
Seating and Safety Restraints If your vehicle has rear seats, always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly. DO NOT place a child in a rear facing infant seat in the front seat unless your vehicle is equipped with an airbag ON/OFF switch and the passenger airbag is turned OFF.
Seating and Safety Restraints • the child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition. 3. Medical condition.
Seating and Safety Restraints • the child has a medical condition that, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’s condition. 3.
Seating and Safety Restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat.
Seating and Safety Restraints When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lb. (36 kg) (about 8 to 12 years old).
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Either type can be used at any seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). Children and booster seats vary widely in size and shape.
Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision.
Seating and Safety Restraints • Top tether anchors can be used for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with a tether anchor.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The passenger seats of your vehicle may be equipped with built-in tether strap anchors located behind the seats as described below.
Seating and Safety Restraints • F-Series Crew Cab Tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. 4. You may need to pull the seatback forward to access the tether anchors. Make sure the seat is locked in the upright position before installing the child seat.
Seating and Safety Restraints • Front seat (SuperCab) • Rear seats (Crew Cab) If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 7. Refer to the Installing child safety seats with combination lap and shoulder belts section of this chapter for further instructions to secure the child safety seat. 8. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Seating and Safety Restraints Many tether straps cannot be tightened if the tether strap is hooked to the loop directly behind the child seat. To provide a tight tether strap: 1. Route the tether strap through the loop directly behind the child seat. 2. Attach the strap hook onto the loop behind an adjacent seating position. 3. Install the child safety seat tightly using the vehicle belts. Follow the instructions in this chapter. 4.
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on shifting procedures and maintenance can be found in your Owner’s Guide. You should become thoroughly familiar with this information before you operate your vehicle. On some 4WD models, the initial shift from two-wheel drive to 4WD while the vehicle is moving can cause a momentary clunk and ratcheting sound.
Tires, Wheels and Loading • Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Tires, Wheels and Loading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Tires, Wheels and Loading TIRES Tires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • Tire Label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry.
Tires, Wheels and Loading INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped).
Tires, Wheels and Loading Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label. When weather temperature changes occur, tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure.
Tires, Wheels and Loading Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. Tire service, including adjusting the air pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Safety and Health Administration (OSHA) regulations.
Tires, Wheels and Loading Stay out of the trajectory (1) as indicated in the illustration. TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear.
Tires, Wheels and Loading Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm). When the tire tread wears down to the same height as these “wear bars”, the tire is worn out and must be replaced.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (138 kPa) greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1.
Tires, Wheels and Loading • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of the 35 mph (55 km/h) point indicated on the speedometer.
Tires, Wheels and Loading Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance and longer tire life. • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD) (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Tires, Wheels and Loading • Dual Rear Wheel (DRW) – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. We do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair. After tire rotation, inflation pressures must be adjusted for the tires new positions in accordance with vehicle requirements. Sometimes irregular tire wear can be corrected by rotating the tires.
Tires, Wheels and Loading INFORMATION CONTAINED ON THE TIRE SIDEWALL U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating.
Tires, Wheels and Loading 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h).
Tires, Wheels and Loading 10. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. 11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire. 1.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading The Tire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The Tire Pressure Monitoring System is NOT a substitute for manually checking tire pressure.
Tires, Wheels and Loading Understanding your Tire Pressure Monitoring System (TPMS) The Tire Pressure Monitoring System measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The Low Tire Warning Lamp will turn ON if the tire pressure is significantly low. Once the light is illuminated, your tires are under inflated and need to be inflated to the manufacturer’s recommended tire pressure.
Tires, Wheels and Loading When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your Tire Pressure Monitoring System: Low Tire Pressure Possible cause Customer Action Required Warning Light Solid Warning Light Tire(s) 1.
Tires, Wheels and Loading Low Tire Pressure Possible cause Customer Action Required Warning Light Flashing Warning Spare tire in Your temporary spare tire is in Light use use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to When your temporary spare tire is installed in this section.
Tires, Wheels and Loading TPMS reset procedure (if applicable) This procedure is only required after tire rotation on vehicles with different front and rear tire pressures. To determine if your vehicle requires two different pressures one for the front tires and one for the rear tires - refer to the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door. See Vehicle Loading in this chapter for more information.
Tires, Wheels and Loading TPMS reset tool A special TPMS reset tool has been provided with your vehicle to reset your TPMS after tire rotation. The tool is located with your Owner’s Guide materials. Please take the tool with the provided Velcro威 strip on the back and mount it in the bottom right corner of your Owner’s Guide case (as shown) for safe keeping.
Tires, Wheels and Loading 3. Press and hold the brake pedal for two (2) seconds, then release. 4. Turn the ignition to OFF/LOCK (DO NOT remove the key.) 5. Cycle the ignition from OFF/LOCK to RUN three (3) times ending in RUN. DO NOT start the engine. If reset mode has been entered successfully, the horn will sound once, the TPMS indicator will flash and the message center will display TRAIN LF TIRE.
Tires, Wheels and Loading 1. Left front tire: Place the TPMS reset tool against the left front tire where the tire meets the rim, opposite from the valve stem (1) as shown. This is where the sensor is located inside the rim. The tool needs to be held against the tire sidewall opposite the valve stem as illustrated with the arrow on the tool pointing towards the rim; do not use the tool with the arrow pointing away from the rim as it may not activate the sensor. 2.
Tires, Wheels and Loading Rotation, pressure adjustment and TPMS reset example The following example describes all the major steps involved in rotating tires on a vehicle with different front and rear tire pressures. It illustrates that the TPMS reset procedure needs to follow tire rotation and pressure adjustment to avoid a possible false low tire warning. Example: A particular vehicle has the following recommended tire pressures: 50 psi (345 kPa) front; 80 psi (552 kPa) rear.
Tires, Wheels and Loading Sensor position following tire rotation Sensor 1: 50 psi Sensor 2: 50 psi Sensor 3: 80 psi Sensor 4: 80 psi Pressure adjustment without the required TPMS reset procedure Sensor 1: 80 psi Sensor 2: 80 psi Sensor 3: 50 psi Sensor 4: 50 psi In this situation, the TPMS warning light will come on. If the TPMS reset procedure is not performed after tire rotation and air pressure adjustment, the TPMS telltale may illuminate for a false low tire pressure condition.
Tires, Wheels and Loading Rotation, pressure adjustment and successful completion of the TPMS reset procedure Sensor 1: 80 psi Sensor 2: 80 psi Sensor 3: 50 psi Sensor 4: 50 psi Tire rotation and air pressure adjustment followed by sensor resetting will ensure the system is properly programmed for vehicles with different front and rear tire pressures and reduce the risk of a false low tire warning. In this situation, the TPMS warning light will be off.
Tires, Wheels and Loading VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance.
Tires, Wheels and Loading The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.
Tires, Wheels and Loading Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
Tires, Wheels and Loading GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.
Tires, Wheels and Loading passengers – that the vehicle can handle without risking damage. (Important: The towing vehicles’ braking system is rated for operation at GVWR, not at GCWR. Separate functional brakes should be used for safe control of towed vehicles and for trailers where the GCW of the towing vehicle plus the trailer exceed the GVWR of the towing vehicle. The GCW must never exceed the GCWR.
Tires, Wheels and Loading 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1,400–750 (5 x 150) = 650 lb.). In metric units (635–340 (5 x 68) = 295 kg.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
Tires, Wheels and Loading The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Tire Label or Safety Compliance Certification Label found on the edge of the driver’s door.
Tires, Wheels and Loading The weight of all additional cargo and passengers must be subtracted from the maximum trailer weight calculated above. Further trailer/hitch restrictions and limitations exist depending on the type of trailer and hitch used. These additional maximum trailer weight and tongue load limitations are listed in the chart/table that follows the listing of GCWRs. Towing a trailer places an additional load on your vehicle’s engine, transmission, axle, brakes, tires and suspension.
Tires, Wheels and Loading Engine 5.4L 6.8L 5.4L 6.8L 5.4L 6.8L 6.8L Maximum GCWR - lb. (kg.) Rear axle Manual Automatic ratio transmission transmission F–350 Dual Rear Wheel (DRW) Pick-up 4.10 17500 (7938) 18500 (8391) 4.10 20500 (9299) 21500 (9752) 4.30 22500 (10206) 23000 (10433) F–350 Single Rear Wheel (SRW) Chassis Cab 3.73 15000 (6804) 16000 (7257) 4.10 17000 (7711) 18000 (8165) 4.10 20000 (9072) 21000 (9525) F–350 Dual Rear Wheel (DRW) Chassis Cab 3.73 15000 (6804) 16500 (7484) 4.
Tires, Wheels and Loading Integrated hitch rating The standard integrated hitch has two ratings depending on mode of operation: • Weight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer. • Weight distributing - requires an aftermarket weight distributing system which includes draw bar, hitch ball, spring bars and snap-up brackets. The vertical tongue load of the trailer is distributed between the truck and the trailer by this system.
Tires, Wheels and Loading 3. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 1⁄2” (13 mm) of the reference point. After proper adjustment, the rear bumper should be no higher than in Step 2. Note: Adjusting a weight distributing hitch so the rear bumper of the vehicle is higher than it was unloaded will defeat the function of the weight distributing hitch and may cause unpredictable handling.
Tires, Wheels and Loading The Ford TBC has only been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and not hydraulic surge or electric-over-hydraulic types. It is the responsibility of the customer to ensure that the trailer brakes are adjusted appropriately, functioning normally and all electric connections are properly made. The TBC user interface consists of the following: 1.
Tires, Wheels and Loading 5. Manual control lever: Slide the control lever to the left to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes (see the following Procedure for adjusting GAIN section for instructions on proper use of this feature). If the manual control is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes.
Tires, Wheels and Loading 6. If the trailer wheels lock-up (indicated by squealing tires), reduce the GAIN setting; if the trailer wheels turn freely, increase the GAIN setting. Repeat Steps 5 and 6 until the GAIN setting is at a point just below trailer wheel lock-up. If towing a heavier trailer, trailer wheel lockup may not be attainable even with the maximum GAIN setting of 10. Explanation of instrument cluster messages: The TBC interacts with the instrument cluster message center.
Tires, Wheels and Loading • Readjust GAIN setting on the TBC (according to procedure above) whenever road, weather and trailer or vehicle loading conditions change from those that existed when the gain was initially set. • The sliding lever on the TBC should be used only for manual activation of trailer brakes to assist with proper adjustment of the GAIN. Misuse, such as application during trailer sway, could cause instability of trailer and/or tow vehicle. • Avoid towing in adverse weather conditions.
Tires, Wheels and Loading Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 km) of trailer towing and don’t make full-throttle starts. • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive transmission shifting, activate the Tow/Haul feature.
Tires, Wheels and Loading • If you will be towing a trailer frequently in hot weather, hilly conditions, at GCWR, or any combination of these factors, consider refilling your rear axle with synthetic gear lubricant if not already so equipped. Refer to Maintenance Product Specifications and Capacities in the Maintenance and Specifications chapter for the proper axle lubricant.
Tires, Wheels and Loading Backing up • Practice backing up, particularly if you are a novice. Turn the steering wheel to the right to move the trailer’s rear end to the right. • Sharp steering movements may cause the trailer to jackknife or go out of control. Tires • All trailer tires should be of the same size, and construction. • Select tires that meet the trailer loading requirements. • Always check tow vehicle and trailer tire pressure before towing.
Tires, Wheels and Loading Transmission Manual Manual Automatic Manual Automatic Drivetrain configuration 4x2 Requirements for neutral towing Place transmission into (N) Neutral1 4x4 with manual-shift Transmission in (N) transfer case Neutral; Transfer case in (N) (Neutral); Hublocks set to FREE1 4x4 with Do not tow your electronic-shift vehicle with any transfer case wheels on the ground, as vehicle or transmission damage may occur.
Driving STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. This position also unlocks the steering wheel. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts.
Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. If your vehicle is operated in a heavy snow storm or blowing snow conditions, the engine air induction may become partially clogged with snow and/or ice.
Driving If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor. • Turn the key to 3 (ON) without turning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) without turning the key to 4 (START).
Driving Note: If the engine does not start on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. If your vehicle has an automatic transmission, it will have a computer assisted cranking system. This feature assists in starting the engine.
Driving Prior to using the engine block heater, follow these recommendations for proper and safe operation: • For your safety, use an outdoor extension cord that is product certified by Underwriter’s laboratory (UL ) or Canadian Standards Association (CSA). Use only an extension cord that can be used outdoors, in cold temperatures, and is clearly marked ⬙Suitable for Use with Outdoor Appliances.⬙ Never use an indoor extension cord outdoors; it could result in an electric shock or fire hazard.
Driving How to Use the Engine Block Heater Ensure the receptacle terminals are clean and dry prior to use. To clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater system may consume anywhere between 400 watts or 1000 watts of energy per hour. Your factory installed block heater system does not have a thermostat; however, maximum temperature is attained after approximately 3 hours of operation.
Driving ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates ABS when the ignition is turned on. If the light does not illuminate during start up, remains on or flashes, the ABS may be disabled and may need to be serviced. Even when the ABS is disabled, ! P normal braking is still effective. (If your BRAKE warning lamp BRAKE illuminates with the parking brake released, have your brake system serviced immediately.
Driving Pull the release lever to release the parking brake. To prevent the pedal from releasing too quickly, place your left foot on the parking brake pedal, then pull the release lever, making sure the pedal fully releases. You may want to pull the release lever again to make sure the parking brake is fully released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
Driving into four-wheel drive mode (if equipped), the traction control system will be automatically disabled. Traction control operation will resume when the vehicle is placed back into two-wheel drive mode. Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage.
Driving • Do not fill the power steering pump reservoir above the MAX mark on the reservoir, as this may result in leaks from the reservoir. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort.
Driving Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed or abrupt maneuvers in these vehicles.
Driving 2. Apply the brake. Use a tool (or a small screwdriver) to pry out the access cover. Insert the tool into the access hole and slide the white override button towards the left. Move the gear shift lever into N (Neutral) while holding the white override disc towards the left. When the key is in the ignition and in the OFF position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed.
Driving Understanding the shift positions of the 5–speed automatic transmission This vehicle is equipped with an adaptive Transmission Shift Strategy. Adaptive Shift Strategy offers the optimal transmission operation and shift quality. When the vehicle’s battery has been disconnected for any type of service or repair, the transmission will need to relearn the normal shift strategy parameters, much like having to reset your radio stations when your vehicle battery has been disconnected.
Driving N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) with Tow/Haul OFF D (Overdrive) with Tow/Haul OFF is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through five. D (Overdrive) with Tow/Haul ON The Tow/Haul feature improves transmission operation when towing a trailer or a heavy load.
Driving 3 (Third) Transmission starts and operates in third gear only. Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever.
Driving To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in the neutral position. 3. Start the engine. 4. Press the brake pedal and move the gearshift lever to the desired gear; 1 (First) or R (Reverse). 5. Release the parking brake, then slowly release the clutch pedal while slowly pressing on the accelerator. During each shift, the clutch pedal must be fully depressed to the floor.
Driving Shift from: D 1 2 Maximum downshift speeds1 6-speed transmission Transfer case position (if equipped)2 2H or 4H 4L 45 mph (72 km/h) 16 mph (26 km/h) (Overdrive) - 4 4-3 35 mph (56 km/h) 12 mph (19 km/h) 3-2 20 mph (32 km/h) 8 mph (13 km/h) 2-1 5 mph (8 km/h) 2 mph (3 km/h) 1-LO Only shift to LO when at a stop. Use 2H or 4H for 4WD equipped vehicles. Downshift at lower speeds when driving on slippery surfaces. Reverse 1.
Driving REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects. To help avoid personal injury, please read and understand the limitations of the reverse sensing system as contained in this section.
Driving The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the RSS detects a stationary or receding object further than 10 inches (25.
Driving If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. REVERSE CAMERA SYSTEM (IF EQUIPPED) The reverse camera system, located on the tailgate, provides a video image (which appears in the rear view mirror) of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle.
Driving Objects in the red zone are closest to your vehicle and objects in the green zone are further away. Objects are getting closer to your vehicle as they move from the green zone to the yellow or red zones. Use the side mirrors and rear view mirror to get better coverage on both sides and rear of the vehicle. When shifting out of reverse and into any other gear, the image will remain on for a few seconds before it shuts off to assist in parking or trailer hookup.
Driving Nighttime and dark area use At night time or in dark areas, the reverse camera system relies on the reverse lamp lighting to produce an image. Therefore it is necessary that both reverse lamps are operating in order to get a clear image in the dark. If either of the lamps are not operating, stop using the reverse camera system, at least in the dark, until the lamp(s) are replaced and functioning.
Driving Manual Shift On Stop (MSOS) 4x4 system (if equipped) The 4WD system is engaged or disengaged by rotating the control for both front wheel hub locks from the FREE or LOCK position, then manually engaging or disengaging the transfer case with the floor-mounted shifter. For increased fuel economy in 2WD, rotate both hub locks to the FREE position. • For proper operation, make sure that each hub is fully engaged and that both hub locks are set to the same position (both set to LOCK or both set to FREE).
Driving • auto-manual hub locks can be manually overridden by rotating the hub lock control from AUTO to LOCK if desired. • automatic operation of the hub locks is recommended, and will increase fuel economy • For proper operation, make sure that each hub is fully engaged and that both hub locks are set to the same position (both set to LOCK or both set to AUTO). To engage LOCK, turn the hub locks completely clockwise; to engage AUTO, turn the hub locks completely counterclockwise.
Driving 4H (4x4 High) – For winter and off-road conditions. Sends power to front and rear wheels. This mode is not intended for use on dry pavement. N (Neutral) – Only used when towing the vehicle. 4L (4x4 Low) – For low-speed off-road applications that require extra power such as steep grades, deep sand or pulling a boat out of the water. Sends power to front and rear wheels. This mode is not intended for use on dry pavement.
Driving Shifting from 4H (4x4 High) to 4L (4x4 Low) 1. Bring the vehicle to a stop or a speed below 5 mph (8 km/h). 2. Place the gearshift lever in N (Neutral). If the vehicle is equipped with a manual transmission, also depress the clutch pedal. 3. Move the transfer case shift lever 2H through N (Neutral) directly to 4L (4x4 Low). 4H 4.
Driving This position should only be used when towing the vehicle. 2H 4H N 4L Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the Electronic Shift On the Fly (ESOF) 4x4 system (if equipped) Positions of the electronic shift system Note: Some noise may be heard as the 4WD system shifts or engages. This is normal. 2WD – For general on-road driving.
Driving • Do not shift into 4x4 HIGH with the rear wheels slipping. Shifting from 4x4 HIGH to 2WD Rotate the 4x4 control to 2WD at any forward speed. Disengagement of the transfer case and front hubs may be delayed due to torque bind which is caused by driving on dry hard surfaces or performing tight turns while using the 4x4 system. • You do not need to operate the vehicle in R (Reverse) to disengage your front hubs, but it will eliminate any torque bind and allow the system to immediately disengage.
Driving 3. Move the 4x4 control to the 4x4 HIGH or 2WD position. 4. Hold the shift conditions until the 4x4 LOW indicator light shuts off. 5. If the 4x4 LOW indicator light does not shut off within 15 seconds, allow the vehicle to move at a speed below 5 mph (8 km/h), then repeat steps 2 through 5 while the vehicle is rolling before reporting any shift concerns to your authorized dealer.
Driving Basic operating principles • Do not use 4WD on dry, hard surfaced roads. Doing so will produce excessive noise, increase tire wear and may damage drive components. 4WD modes are only intended for consistently slippery or loose surfaces. • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water, gravel, snow or ice.
Driving Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Refer to Transmission fluid temperature gauge in the Instrument Cluster chapter for transmission fluid temperature information.
Driving transmission is in P (Park) or the manual transmission is in gear. Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Driving Note: If air is released from your tires, the Tire Pressure Monitoring System (TPMS) indicator light may illuminate (if equipped). Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes.
Driving Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehand the route you will use.
Driving Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. Avoid sudden braking as well.
Driving VEHICLE USED AS A STATIONARY POWER SOURCE Auxiliary equipment called power take-off, or PTO, is often added to the engine or transmission to operate utility equipment. Examples include a wheel-lift for tow trucks, cranes, tools for construction or tire service, and pumping fluids. PTO applications draw auxiliary horsepower from the powertrain, often while the vehicle is stationary.
Driving SNOWPLOWING Ford recommends that the Super Duty F-Series used for snow removal include a snow plow package option. Installing the snowplow Weight limits and guidelines for selecting and installing the snowplow can be found in the Ford Truck Body Builders Layout Book, Snowplow section, found at www.fleet.ford.com/truckbbas. A typical installation affects the following: • Certification to government safety laws such as occupant protection and airbag deployment, braking, and lighting.
Driving • Snowplowing with vehicles equipped with a diesel engine may result in engine overheating in highway driving with snowplow blade raised unless equipped with the special engine cooling fan clutch that is included with a snow plow package option. Operating the vehicle with the snowplow attached Do not use your vehicle for snow removal until it has been driven at least 500 miles (800 km).
Driving Additional equipment such as snowplow equipment may effect the performance of the airbag sensors increasing the risk of injury. Please refer to the Ford Truck Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Transmission operation while plowing Operate the vehicle with the automatic transmission gearshift lever in the D (Overdrive) position and Tow/Haul off.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the coverage period listed on the Roadside Assistance Card included in your Owner Guide portfolio.
Roadside Emergencies Canadian customers refer to your Customer Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment.
Roadside Emergencies HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
Roadside Emergencies The switch has a red button on top of it. To reset the switch: 1. Turn the ignition off. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition on. 5. Wait a few seconds and return the key to off. 6. Make another check for leaks. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.5A 10A 15A 20A 25A 30A 40A 50A 60A 70A 80A Grey Violet Pink Tan Brown Red Blue Yellow Natural Green — — — — — Grey Violet Pink Tan Brown Red Blue Yellow Natural Green — — — — — — — — — — — — Yellow — Green Orange Red Blue Tan Natural Passenger compartment fuse panel The fuse panel is located in the passenger’s footwell. Remove the panel cover to access the fuses.
Roadside Emergencies To remove the fuse panel cover, pull the panel toward you. When the clips of the panel disengage, let the panel fall easily. To remove a fuse use the fuse puller tool provided on the fuse panel cover. Always disconnect the battery before servicing high current fuses. Always replace the cover to the passenger compartment fuse panel before reconnecting the battery.
Roadside Emergencies The fuses are coded as follows.
Roadside Emergencies Fuse/Relay Location 11 12 Fuse Amp Rating 10A 7.
Roadside Emergencies Fuse/Relay Location 32 Fuse Amp Rating 10A 33 10A 34 35 5A 10A 36 5A 37 10A 38 39 40 41 20A 20A 20A 15A 42 10A 43 10A 44 10A 45 5A 46 47 7.
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies Fuse/Relay Location 6 7 8 9 10 11 12 13 Fuse Amp Rating 40A* 30A* 30A* 40A* 20A* 20A* 15A** 5A ** 14 15 16 17 18 — — Relay Relay Relay 19 Relay 20 21 22 Relay Relay Relay 23 24 25 26 27 15A** 40A* — 30A* 50A* 28 20A* 304 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description ABS module (Pump) Upfitter auxiliary switch #1 Upfitter auxiliary switch #2 ABS module (Coil) Cigar lighter Instrument panel power point Brake On/Off (BO
Roadside Emergencies Fuse/Relay Location 29 30 31 32 33 34 35 36 Fuse Amp Rating 30A* 10A** 15A** 20A** 20A** 25A** 5A** 10A** 37 10A** 38 39 40 41 — 50A* 30A* 20A* 42 43 44 45 30A* 20A* 30A* 30A* 46 47 48 49 50 40A* 50A* 30A* 30A* 30A* 51 52 — — Power Distribution Box Description Passenger power seat A/C clutch relay Power fold mirror relay Fuel pump relay Back-up lamp relay Trailer stop/turn relay ESOF relay coils Gasoline engines: Powertrain Control Module (PCM) keep alive power, Canister ven
Roadside Emergencies Fuse/Relay Location 53 Fuse Amp Rating Relay 54 55 56 57 Relay Relay Relay Relay 58 59 Relay Relay 60 61 62 63 64 65 66 67 68 69 70 Diode Diode Diode 15A** 5A** — — — — — 10A** 71 5A** 72 15A** 306 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description PCM power bus (Fuses 68, 70, 72, 74, 76) (Diesel engine only) Starter solenoid Trailer tow park lamps Trailer tow battery charge Power Distribution Box (PDB) bus (fuses 67, 69,
Roadside Emergencies Fuse/Relay Location 73 74 Fuse Amp Rating 2A** 20A** 75 76 5A** 20A** 77 10A** * Cartridge fuses ** Mini fuses Power Distribution Box Description Reverse Camera System (RCS) Gasoline engines: VPWR: HEGO, CMS, MAFS, EVMV, CMCV, VCT, IMTV Diesel engine: VPWR: Engine loads Back-up relay coil power Gasoline engines: VPWR: PCM Diesel engine: VPWR: ECM ABS module logic CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily.
Roadside Emergencies Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford.
Roadside Emergencies 3.
Roadside Emergencies When driving with the temporary spare tire do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • Tow a trailer • Use snow chains on the end of the vehicle with the temporary spare tire • Use more than one temporary spare tire at a time Use of a temporary spare tire at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance
Roadside Emergencies Location of the spare tire and tools If your vehicle is equipped with a spare tire, jack and associated tools, refer to the following table for their locations: Tool Spare tire (pick-up trucks only) Jack Jack handle, lug wrench, lug wrench extension (only available on Dual Rear Wheel [DRW] vehicles) and wheel chock (only available on Single Rear Wheel [SRW] vehicles equipped with a diesel engine) Key and spare tire lock Jack instruction sheet Location Under the vehicle, just forward o
Roadside Emergencies • Vehicles equipped with dual rear wheels, insert the lug wrench extension into the lug wrench to reach the lug nuts. 2. Attach the spare tire lock key (A) to the jack handle (B). 3. Fully insert the jack handle (with one extension) through the bumper hole and into the guide tube. The key and lock will engage with a slight push and counterclockwise turn. Some resistance will be felt when turning the jack handle assembly. 4.
Roadside Emergencies 4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or R (Reverse) (manual transmission).
Roadside Emergencies • Front driver side (4x4) Note: Make sure the jack fits onto the flat area on the outboard side of the differential. • Front passenger side (4x4) Note: View shown from the rear of the vehicle to clearly identify the jack point. Place the jack directly under the axle.
Roadside Emergencies Never use the front or rear differential as a jacking point. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 7. Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 8. Remove the lug nuts with the lug wrench. 9.
Roadside Emergencies 12. Position the jack according to the following guides: • Front (4x2): F–350 DRW Note: Place jack directly under I-beam. • Front driver side (4x4): F–350 DRW Note: Make sure the jack fits onto the flat area on the outboard side of the differential housing. • Front passenger side (4x4): F-350 DRW Note: View shown from the rear of the vehicle to clearly identify the jack point.
Roadside Emergencies • Front: F–450/F–550 • Rear: F-350 DRW • Rear: F-450/F-550 13. Insert the jack handle into the pump linkage. 14. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’s rated capacity.
Roadside Emergencies 15. Remove the lug nuts with the lug wrench. 16. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels. If replacing the outboard wheel, the valve stem must be facing inward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 17. Lower the wheel by slowly turning the release valve counterclockwise.
Roadside Emergencies 10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier. Note: Do not stow the Harley-Davidson flat tire and wheel using the spare tire winch mechanism; store the flat in the bed of the truck. 20. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not rattle when driving. 21. Unblock the wheels.
Roadside Emergencies If the ornament retention towers are aligned between the studs/lug nuts, the ornament is improperly installed. This improper installation may appear and sound correct, but will not keep the ornament on the vehicle. Ornaments improperly installed in this manner will fall off or become loose with minimal force or impact. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1.
Roadside Emergencies WHEEL LUG NUT TORQUE SPECIFICATIONS On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).
Roadside Emergencies Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger. DO NOT apply grease to lug nut/stud holes or wheel-to-brake surfaces.
Roadside Emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off. Connecting the jumper cables + + – – 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. Note: It is recommended that the vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If the vehicle is towed by any other means or incorrectly, vehicle damage may occur.
Roadside Emergencies Note: Towing an ESOF 4x4 vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatic transmission. Note: Towing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph (56 km/h) may cause damage to the automatic transmission. Note: On Dual Rear Wheel (DRW) vehicles, an outer rear wheel must be removed prior to using a wheel lift wrecker.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program.
Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate.
Customer Assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.
Customer Assistance To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning PAINT CHIPS Your authorized dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots and industrial fallout before repairing paint chips. • Always read the instructions before using the products.
Cleaning • 5.4L V8 gasoline engine • 6.
Cleaning PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly.
Cleaning • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system.
Cleaning For removal of fine scuffs and scratches, use Scotch-Britet Microfiber Cloth or cheese cloth along with Motorcraft Premium Liquid Wax (ZC-53-A), Motorcraft Paint Sealant (ZC-45), or Motorcraft Custom Clear Coat Polish (ZC-8-A). Note: Removal of deep scuffs and scratches should be performed by an authorized dealer or an experienced repair facility.
Cleaning LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCH F–250 AND F–350 CREW CAB) Your leather seating surfaces have a clear, protective coating over the leather. For King Ranch F-250 and F-350 Crew Cab leather seats, refer to separate section in this chapter. • To clean, use a soft cloth with Motorcraft Deluxe Leather and Vinyl Cleaner (ZC-11–A). Dry the area with a soft cloth.
Cleaning • Do not spill coffee, ketchup, mustard, orange juice or oil-based products on the leather as they may permanently stain the leather. • Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl or plastics. Scratches Natural Markings - Because the leather in the seat comes from genuine steer hides, there will be evidence of naturally occurring markings, such as small scars.
Cleaning FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered.
Maintenance and Specifications 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Refer to the 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 5.4L V8 gasoline engines 1. Windshield washer fluid reservoir 2. Battery 3. Transmission fluid dipstick (automatic transmission) 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Brake fluid reservoir 8. Engine coolant reservoir 9. Air filter assembly 10.
Maintenance and Specifications 6.8L V10 gasoline engine 1. Windshield washer fluid reservoir 2. Battery 3. Transmission fluid dipstick (automatic transmission) 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Brake fluid reservoir 8. Engine coolant reservoir 9. Air filter assembly 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellant-type fluid or bug wash as this may cause a squeaking/chattering noise, streaking or smearing. Refer to Maintenance Product Specifications and Capacities in this chapter.
Maintenance and Specifications Note: Poor wiper quality can be improved by cleaning the wiper blades and the windshield; refer to Windows and wiper blades in the Cleaning chapter. Note: To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.
Maintenance and Specifications 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1.
Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications RN LE A TU D RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “COLD FILL RANGE” in the coolant reservoir. • Refer to the scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty.
Maintenance and Specifications Note: Use of Motorcraft Cooling System Stop Leak Pellets may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant meeting Ford specification WSS-M97B44–D, or DEX-COOL威 brand with the factory-filled coolant.
Maintenance and Specifications 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “COLD FILL RANGE” on the reservoir. 6. Replace the cap. Turn until tightly installed. (Cap must be tightly installed to prevent coolant loss.
Maintenance and Specifications Severe climates If you drive in extremely cold climates (less than –34°F [–36°C ]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance and Specifications How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The message center will indicate the engine is overheating. indicator will • The illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate.
Maintenance and Specifications 5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to the scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part.
Maintenance and Specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and Specifications Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position. Refueling • • • • • • Fuel vapor burns violently and a fuel fire can cause bad injuries.
Maintenance and Specifications If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The vehicle warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Maintenance and Specifications Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally, adding one gallon of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than one gallon may be required. • The Service engine soon indicator ( ) may come on.
Maintenance and Specifications • Use the same filling rate setting (low-medium-high) each time the tank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time.
Maintenance and Specifications • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy.
Maintenance and Specifications • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation.
Maintenance and Specifications If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Maintenance and Specifications 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter. 4. Driving through deep water - the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cycles without these or any indicator should stay off other temporary malfunctions present, the the next time the engine is started.
Maintenance and Specifications POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance information for the service interval schedules. If adding fluid is necessary, use only MERCON威 ATF. • Gasoline engine shown; diesel engine similar. Refer to Identifying components in the engine compartment in the 6.0 and 6.4 Liter Power Stroke Direct Injection Turbo Diesel Owner Guide Supplement. Check the fluid level when it is at ambient temperature, 20°F–80°F (-7°C–25°C): 1.
Maintenance and Specifications BRAKE FLUID • Vacuum boost system • Hydroboost system • FEAD-driven vacuum pump/brake booster system 374 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus)
Maintenance and Specifications The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range the performance of your brake system could be compromised; seek service from your authorized dealer immediately. CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level.
Maintenance and Specifications Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 20 miles [30 km]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1.
Maintenance and Specifications The transmission fluid should be in this range if at normal operating temperature (150°F-170°F [66°C-77°C]). The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
Maintenance and Specifications Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Maintenance Product Specifications and Capacities in this chapter.
Maintenance and Specifications TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Maintenance Product Specifications and Capacities in this chapter.
Maintenance and Specifications DRIVELINE UNIVERSAL JOINT AND SLIP YOKE If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will be necessary. Refer to the replacement universal joint manufacturer’s recommendation for lubrication type and maintenance intervals. AIR FILTER MAINTENANCE Refer to the scheduled maintenance information for the appropriate intervals for changing the air filter element.
Maintenance and Specifications 2. Release three retainer clamps. 3. Pull air filter cover toward passenger side of vehicle and up to release the tabs. Lift air filter element up and out of housing. The air filter box needs to be free of any debris before installing a new air filter. 4. Install a new air filter element into the tray assembly. 5. Return air filter cover to original position making sure the four tabs are engaged and secure the three clamps. Tighten clamp on air tube and reconnect sensor.
Maintenance and Specifications MOTORCRAFT PART NUMBERS Component 5.4L V8/6.8L V10 engines Air filter element FA-1883 Fuel filter FG-1011 Oil filter FL-820-S 1 PCV valve Battery (Standard) BXT-65-650 Battery (Optional) BXT-65-750 2 Spark plugs-platinum 3, 4 Remote Automatic Transmission Filter 1 The PCV valve is a critical emission component. It is one of the items listed in the scheduled maintenance information and is essential to the life and performance of your vehicle and to its emissions system.
2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Engine coolant - 5.4L V8 engine with A/C2 Brake fluid (and clutch fluid, if equipped) Rear axle - F-450/550 (Dana S110/S130) Rear axle - F-350 (DANA M80) Rear axle - F-250/350 (10.50 inch axle)1 Spindle bearing Front axle Item Ford part name Ford part number / Ford specification 5.8 pints (2.
2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Fuel tank - Aft axle (Chassis cab only) Fuel tank - Long box Fuel tank - Short box Engine oil (includes filter change) - diesel engine6 Fuel tank - Mid-ship tank (optional on Chassis Cab) Engine oil (includes filter change) - 5.4L V8 and 6.8L V10 gas engines6 Engine and fuel coolant - diesel engine Engine coolant - 6.8L V10 engine2 Item Ford part name Ford part number / Ford specification 30.0 gallons (113.4L) 38.
Motorcraft Premium Long-Life Grease MERCON威 V Automatic Transmission Fluid — Keep fluid level between MIN and MAX on reservoir 2.0 quarts (1.9L) 5.8 quarts (5.5L)4 Transmission / parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Power steering fluid Transfer case fluid 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Manual transmission fluid XT-M5-QM / WSS-M2C200–C XL-12 / — 17.5 quarts Automatic transmission (16.
3.5 quarts (3.3L) Windshield washer fluid Ford part number / Ford specification ZC-32–A / WSB-M8B16–A2 Ford part name Motorcraft Premium Windshield Washer Concentrate 386 2008 F-250/350/450/550 (f23) Owners Guide (post-2002-fmt) USA (fus) Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark. 6 5 Indicates only approximate dry-fill capacity.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio 5.4L V8 engine 330 87 octane 1-3-7-2-6-5-4-8 1.02–1.28mm (0.040–0.050 inch)* Coil on plug 9.8:1 6.8L V10 engine 415 87 octane 1-6-5-10-2-7-3-8-4-9 1.02–1.28mm (0.040–0.050 inch)* Coil on plug 9.2:1 *The 5.4L 3V and 6.8L 3V spark plug gap CANNOT be adjusted. Drivebelt routing 5.4L V8/6.
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on the vehicle Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents.
Accessories GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada authorized dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Lifestyle Ash cup / smoker’s package Bedliners and bedmats Cargo organization and management Towing mirrors Trailer hitches, wiring harnesses and accessories Peace of mind Mobile-Ease™ hands-free communication system Remote start Vehicle security systems Wheel locks Not all accessories are available for all models.
Index A Accessory delay ........................103 Air cleaner filter ...............380, 382 Air conditioning ..........................80 Airbag supplemental restraint system ........................................184 and child safety seats ............185 description ..............................184 disposal ....................................188 driver airbag ............................186 indicator light .........................187 operation .................................186 passenger airbag .
Index Climate control (see Air conditioning or Heating) ............80 Clock adjust 6-CD in dash .............................34 AM/FM/CD .................................28 Clutch fluid ..........................................375 operation while driving ..........269 recommended shift speeds ....270 Compass, electronic set zone adjustment ...............134 Console ......................................120 overhead ..................................100 Controls power seat ...............................
Index Family entertainment system ....48 Fluid capacities .........................383 Foglamps .....................................85 Four-Wheel Drive vehicles .......276 description ..............................281 driving off road .......................283 electronic shift ................277, 281 indicator light .........................278 lever operated shift ................278 manual locking hubs ..............277 preparing to drive your vehicle .....................................264 Fuel .....
Index autolock ...................................147 programming entry code .......157 Keys ...........................................160 positions of the ignition .........255 L Lamps autolamp system .......................85 daytime running light ...............86 fog lamps ...................................85 headlamps .................................85 headlamps, flash to pass ..........86 instrument panel, dimming .....87 interior lamps ...........................91 replacing bulbs .............
Index Rear seat entertainment system ..........................................48 Rear video camera ....................274 Relays ........................................297 Remote entry system ...............151 illuminated entry ............155–156 locking/unlocking doors ........................146, 151–152 Reverse sensing system ...........272 Roadside assistance ..................294 S Safety Belt Maintenance ..........183 Safety belts (see Safety restraints) ..........
Index snow tires and chains ............235 spare tire .........................308–309 terminology .............................208 tire grades ...............................207 treadwear ........................207, 213 Towing .......................................242 recreational towing .................253 Trailer Brake Controller-Integrated ..............246 trailer towing ..........................242 wrecker ....................................327 Traction control ........................
