2014 ESCAPE Owner’s Manual EJ5J 19A321 AB | 2014 ESCAPE Owner’s Manual fordowner.com ford.ca April 2014 | Fourth Printing | Owner’s Manual | Escape | Litho in U.S.A.
The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2014 All rights reserved.
Table of Contents Driver Knee Airbag.........................................39 Safety Canopy™............................................39 Crash Sensors and Airbag Indicator.........41 Airbag Disposal...............................................42 Introduction About This Manual...........................................7 Symbols Glossary.............................................7 Data Recording..................................................9 California Proposition 65..............................
Table of Contents Autowipers........................................................70 Windshield Washers.......................................71 Rear Window Wiper and Washers...........72 Remote Start.................................................108 Seats Sitting in the Correct Position...................110 Head Restraints.............................................110 Manual Seats..................................................112 Power Seats.....................................................
Table of Contents Luggage Covers.............................................167 Roof Racks and Load Carriers.................168 Load Limit.......................................................169 Transmission Automatic Transmission...........................138 Four-Wheel Drive Towing Principle of Operation..................................141 Using Four-Wheel Drive..............................141 Towing a Trailer..............................................177 Trailer Sway Control................
Table of Contents Cleaning the Windows and Wiper Blades...........................................................231 Cleaning the Interior....................................231 Cleaning the Instrument Panel and Instrument Cluster Lens.........................231 Cleaning Leather Seats..............................232 Repairing Minor Paint Damage...............233 Cleaning the Alloy Wheels.......................233 Vehicle Storage.............................................
Table of Contents Audio Input Jack...........................................287 USB Port..........................................................287 Media Hub......................................................288 SYNC™ General Information...................................289 Using Voice Recognition............................291 Using SYNC™ With Your Phone............293 SYNC™ Applications and Services......304 Using SYNC™ With Your Media Player........................................................
6 Escape (TM2) , enUSA
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Introduction Battery Engine oil Battery acid Explosive gas Brake fluid - non petroleum based Fan warning Brake system Fasten safety belt Cabin air filter Front airbag Check fuel cap Front fog lamps Child safety door lock or unlock Fuel pump reset Child seat lower anchor Fuse compartment Child seat tether anchor Hazard warning flashers Cruise control Heated rear window Do not open when hot Heated windshield E71340 E91392 Engine air filter Interior luggage compartment release Engine
Introduction Low tire pressure warning DATA RECORDING Service Data Recording Maintain correct fluid level Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems.
Introduction The event data recorder in this vehicle is designed to record such data as: • How various systems in your vehicle were operating; • Whether or not the driver and passenger safety belts were buckled/fastened; • How far (if at all) the driver was depressing the accelerator and/or the brake pedal; and • How fast the vehicle was traveling; and • Where the driver was positioning the steering wheel.
Introduction REPLACEMENT PARTS RECOMMENDATION CALIFORNIA PROPOSITION 65 WARNING Your vehicle has been built to the highest standards using quality parts. We recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair. You can clearly identify genuine Ford and Motorcraft parts by looking for the Ford, FoMoCo or Motorcraft branding on the parts or their packaging.
Introduction Warranty on Replacement Parts Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death. Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty.
Introduction WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
Child Safety GENERAL INFORMATION WARNINGS requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and consult your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in your vehicle. To locate a child seat fitting station and CPST, contact the NHTSA toll free at 1-888-327-4236 or go to http://www.nhtsa.dot.gov. In Canada, check with your local St.
Child Safety Recommendations for Safety Restraints for Children Child Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger). Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat). Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 ft. 9 in. (1.
Child Safety • Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers, or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). • Using Lap and Shoulder Belts Place the vehicle seat upon which the child seat will be installed in the upright position. Put the safety belt in the automatic locking mode. See Step 5. This vehicle does not require the use of a locking clip.
Child Safety E142530 E142875 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. Note: The automatic locking mode is available on the front passenger and rear seats. 6. Allow the belt to retract to remove slack.
Child Safety Using Lower Anchors and Tethers for CHildren (LATCH) 8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle.
Child Safety Use of Inboard Lower Anchors from the Outboard Seating Positions (Center Seating Use) WARNING The standardized spacing for LATCH lower anchors is 11 inches (28 centimeters) center to center. Do not use LATCH lower anchors for the center seating position unless the child seat manufacturer's instructions permit and specify using anchors spaced at least as far apart as those in this vehicle.
Child Safety Combining Safety Belt and LATCH Lower Anchors for Attaching Child Safety Seats Perform the following steps to install a child safety seat with tether anchors: Note: If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off your vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Child Safety recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms). Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat: E142539 3. Clip the tether strap to the anchor as shown. 4.
Child Safety Types of Booster Seats E70710 • E68924 • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child's head (as measured at the tops of the ears) above the top of the seat.
Child Safety E142597 WARNINGS warnings provided by your vehicle manufacturer. A safety seat that is improperly installed or utilized, is inappropriate for your child's height, age, or weight or does not properly fit the child may increase the risk of serious injury or death. If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Child Safety Recommendations for attaching child safety restraints for children Restraint type Combined weight of child and child restraint seat Use any attachment method as indicated below by X LATCH (lower anchors and top tether anchor) LATCH (lower anchors only) Rear facing Up to 65 lb child seat (29.5 kg) Safety belt Safety belt Safety belt and LATCH only and top (lower tether anchors anchor and top tether anchor) X X Rear facing Over 65 lb child seat (29.
Child Safety Left-Hand Side Turn counterclockwise to lock and clockwise to unlock. Right-Hand Side Turn clockwise to lock and counterclockwise to unlock.
Safety Belts PRINCIPLE OF OPERATION WARNINGS Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. WARNINGS Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained.
Safety Belts The safety belt pretensioners are designed to activate in frontal, near-frontal and side crashes, and in rollovers. The safety belt pretensioners on the retractor and anchor at the front seating positions are designed to tighten the safety belts firmly against the occupant's body when activated. This helps increase the effectiveness of the safety belts.
Safety Belts All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first type of locking mode, and the front outboard passenger and rear seat safety belts have both types of locking modes described as follows: Vehicle Sensitive Mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Safety Belts How to Use the Automatic Locking Mode 3. Return the seatback to its desired upright position. For vehicles with rear seats that do not recline or are locked with the seat in its full rear recline position: 1. 2. 3. E142591 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out. 4. 5. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Safety Belts To adjust the shoulder belt height, squeeze the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place. SAFETY BELT HEIGHT ADJUSTMENT WARNING Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt correctly could reduce the effectiveness of the safety belt and increase the risk of injury in a crash.
Safety Belts The system uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the Belt-Minder feature for objects placed in the front passenger seat, warnings will only be given to large front seat occupants as determined by the front passenger sensing system.
Safety Belts Deactivating and Activating the Belt-Minder Feature 4. While the safety belt warning light is on, buckle and then unbuckle the safety belt. After Step 4, the safety belt warning light will flash for confirmation. • This will disable the feature for that seating position if it is currently enabled. • This will enable the feature for that seating position if it is currently disabled.
Personal Safety System™ How Does the Personal Safety System Work? The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Supplementary Restraints System The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. PRINCIPLE OF OPERATION WARNINGS Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module.
Supplementary Restraints System Proper Driver and Front Passenger Seating Adjustment DRIVER AND PASSENGER AIRBAGS WARNING WARNINGS Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Supplementary Restraints System This system works with sensors that are part of the front passenger’s seat and safety belt to detect the presence of a properly–seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or not. E142846 Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Supplementary Restraints System • • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the passenger airbag status indicator will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled.
Supplementary Restraints System If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • Objects lodged underneath the seat • Objects between the seat cushion and the center console • Objects hanging off the seatback • Objects stowed in the seatback map pocket • Objects placed on the occupant's lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat • • •
Supplementary Restraints System The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. WARNINGS If the side airbag has deployed, the airbag will not function again.
Supplementary Restraints System WARNINGS Do not attempt to service, repair, or modify the curtain airbags, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing curtain airbags as you could be seriously injured or killed. Contact your authorized dealer as soon as possible. All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided.
Supplementary Restraints System • CRASH SENSORS AND AIRBAG INDICATOR • WARNING Modifying or adding equipment to the front end of your vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of your vehicle. • If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately.
Supplementary Restraints System The fact that the safety belt pretensioners or airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (for example, crash severity, belt usage) were not appropriate to activate these safety devices.
Keys and Remote Controls Intelligent Access (If Equipped) GENERAL INFORMATION ON RADIO FREQUENCIES The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met: • You touch the inside of the front exterior door handle. • You press the luggage compartment button. • You press a button on the transmitter. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Keys and Remote Controls The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door. Slide the release on the back of the transmitter to release the key blade, then pull the blade out. E138615 Note: Your vehicle’s keys came with a security label that provides important vehicle key cut information. Keep the label in a safe place for future reference.
Keys and Remote Controls Integrated Keyhead Transmitter E142432 2. Twist a thin coin under the tab hidden behind the backup key head to remove the battery cover. Do not use the backup key to remove the cover or you could damage the intelligent access key. E138619 1. Twist a thin coin in the slot of the transmitter near the key ring to remove the battery cover. 2. Remove the old battery. E138620 3. Insert the new battery.
Keys and Remote Controls Note: If locking was not successful or if any door or the liftgate is open, or if the hood is open on vehicles with a perimeter alarm or remote start, the horn will sound twice and the lamps will not flash. • • • • Sounding a Panic Alarm Note: The panic alarm will only operate when the ignition is off. E138624 Remote Starting the Vehicle Note: You must press each button within three seconds of each other.
Keys and Remote Controls The power windows will be inhibited during the remote start and the radio will not turn on automatically. The parking lamps will remain on and the vehicle will run for 5, 10, or 15 minutes, depending on the setting. Extending the Vehicle Run Time Repeat Steps 1 and 2 with the vehicle still running to extend the run time for another remote start duration. If the duration is set to last 10 minutes, the duration will extend by another 10 minutes.
MyKey™ PRINCIPLE OF OPERATION • MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. • • Any keys that have not been programmed are referred to as administrator keys or admin keys. These can be used to: • • • create a MyKey program configurable MyKey settings clear all MyKey features.
MyKey™ Programming/Changing Configurable Settings CREATING A MYKEY Use the information display to create a MyKey: Use the information display to access your configurable MyKey settings: 1. Insert the key you want to program into the ignition. If your vehicle is equipped with a push-button start, hold the intelligent access key next to the steering column. Details on the correct fob placement and position is in another chapter. See Starting and Stopping the Engine (page 124). 1.
MyKey™ Message Action and Description All MyKeys Cleared Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.
MyKey™ You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 89). CHECKING MYKEY SYSTEM STATUS To find information on a programed MyKey(s), press the left arrow button to access the main menu and scroll to: Message Description Settings Press the OK button. MyKey Press the OK button. Select one of the following: MyKey Dist. Tracks the distance when drivers use a MyKey.
MyKey™ 2. Start your vehicle using your remote start fob. 3. See Clearing All MyKeys (page 49). Follow Steps 1-3. USING MYKEY WITH REMOTE START SYSTEMS Vehicles With Ford-Approved Aftermarket Remote Start Systems After clearing your MyKeys, you can create a new MyKey. See Creating a MyKey (page 49). When using a Ford-approved aftermarket remote start system, the vehicle recognizes the remote start system as an additional admin key. It is the vehicle’s default setting.
MyKey™ As an added precaution, owners of vehicles fitted with traditional keys may want to program the remote start system as a MyKey, if the MyKey driver uses the remote start fob. That way, when the MyKey driver starts the vehicle with the remote start system, the MyKey restrictions remain active. 1. Enter your vehicle and close all doors. 2. Start your vehicle using your non-Ford-approved remote start fob. 3. See Clearing All MyKeys (page 49). Follow Steps 1-3.
MyKey™ Condition Potential Causes · The vehicle has been started using a remote start system that is not programmed with admin privileges. See Using MyKey With Remote Start Systems (page 52). I cannot clear the MyKeys. · The key or fob used to start your vehicle does not have admin privileges. · No MyKeys are created. See Creating a MyKey (page 49). · The vehicle has been started using a remote start system that is not programmed with admin privileges. See Using MyKey With Remote Start Systems (page 52).
Locks Press and hold both the lock and unlock buttons on the remote control for four seconds to disable or enable two-stage unlocking. Disabling two-stage unlocking allows all vehicle doors to unlock with one press of the button. The turn signals will flash twice to indicate a change to the unlocking mode. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access.
Locks Right-Hand Side Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Turn counterclockwise to lock. Opening a Rear Door from Inside Press twice within three seconds to: Pull the interior door release handle twice to unlock and open a rear door. The first pull unlocks the door and the second pull will unlatch the door. E138630 • • unlatch a manual liftgate open, close or stop the movement of a power liftgate.
Locks In order to override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle, you can lock your vehicle after all doors are closed by using the keyless entry keypad, pressing the lock button on another intelligent access key or touching the locking area on the handle with another intelligent access key in your hand. At the Liftgate Press the exterior liftgate release button on the top of the liftgate pull-cup handle.
Locks The illuminated entry system will turn off the lights if: • you start your vehicle, • you press the remote control lock button, or • after 25 seconds of illumination. Enabling or Disabling Autolock and Autounlock Note: Your authorized dealer can perform this procedure, or you can do the procedure yourself. To enable or disable these features, do the following: The lights will not turn off if: • you turn them on with the lamp control, or • any door is open.
Locks Opening the Liftgate MANUAL LIFTGATE Manually WARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. Failure to follow this warning could result in serious personal injury or death.
Locks POWER LIFTGATE (If Equipped) • WARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
Locks Hands-Free Feature (If Equipped) With the Outside Control Button Make sure you have an intelligent access transmitter within 3 feet (1 meter) of the liftgate. Opening 1. 2 Unlock the liftgate with the remote control or power door unlock control. If an intelligent access transmitter is within 3 feet (1 meter) of the liftgate, the liftgate will unlock when you press the liftgate release button. 1 E161602 E138632 1. Move your foot under and away from the rear bumper similar to a kicking motion.
Locks When Opening WARNING Keep clear of the liftgate when activating the rear switch. The system stops when it detects an obstacle and two short tones sound. Remove the obstacle to operate the liftgate. Setting the Liftgate Open Height 1. Open the liftgate. 2. Manually move the liftgate to the desired height. 3. Press and hold the control button on the liftgate until you hear a chime, indicating programming is complete.
Locks All personal codes will erase and only the factory-set five-digit code will work. You can operate the keypad with the factory-set five-digit entry code. The code is located on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also create up to five of your own five-digit personal entry codes. Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses).
Security Replacement Keys PASSIVE ANTI-THEFT SYSTEM Note: Your vehicle comes equipped with two integrated keyhead transmitters or two intelligent access keys. Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote control.
Security You must have two previously programmed coded keys and the new unprogrammed key readily accessible. See your authorized dealer to have the spare key programmed if two previously programmed coded keys are not available. Programming a Spare Intelligent Access Key See your authorized dealer to have additional keys programmed to your vehicle. Read and understand the entire procedure before you begin. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 110). 3 E95179 2 3. Lock the steering column. AUDIO CONTROL (If Equipped) Select the required source on the audio unit. 1 You can operate the following functions with the control: 2 E95178 1. Unlock the steering column. 2. Adjust the steering wheel to the desired position.
Steering Wheel Type 1 Type 2 A E A D C B D B C E129462 A Volume up E129463 A Volume up B Seek up or next B Seek up or next C Volume down C Volume down D Seek down or previous D Seek down or previous E Mode Seek, Next or Previous Press M to select the audio source. Press the seek button to: • tune the radio to the next or previous stored preset • play the next or the previous track.
Steering Wheel CRUISE CONTROL VOICE CONTROL (If Equipped) E142437 See Cruise Control (page 160). E161798 Pull the control to select or deselect voice control. See SYNC™ (page 289). See MyFord Touch™ (page 324). INFORMATION DISPLAY CONTROL MyFord Touch® Controls (If Equipped) Your steering wheel controls may also have these additional features. Press to go to the home screen. E142613 Press to go to the information screen. E142608 See MyFord Touch™ (page 324).
Steering Wheel Multimedia Controls (If Equipped) E145434 Use the arrows on the right side of the steering wheel to navigate through the menus. Press OK to make a selection.
Wipers and Washers Intermittent Wipe WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.
Wipers and Washers Note: During wet or winter driving conditions with ice, snow or a salty road mist, inconsistent or unexpected wiping or smearing may occur. Keep the outside of the windshield clean. The rain sensor is very sensitive. Dirt or debris around the interior rear view mirror area will affect the autowipers' performance. For example, the autowipers may turn on if dirt, mist or insects hit the windshield.
Wipers and Washers Rear Window Washer REAR WINDOW WIPER AND WASHERS Rear Window Wiper E168044 To use the rear washer function, push the lever away from you. When you release the lever, the wiper will operate for a short time. E168043 A Intermittent wipe B Low-speed wipe C Off Press the top of the button at the end of the lever to switch on the intermittent wiper. Press the button again to switch on low-speed wipe.
Lighting LIGHTING CONTROL Headlamp Flasher E142449 Pull the lever toward you slightly and release it to flash the headlamps. E162680 A Off B Parking lamps, instrument panel lamps, license plate lamps and tail lamps C AUTOLAMPS (If Equipped) Headlamps High Beams E142451 The headlamps will switch on and off automatically in low light situations or during inclement weather. E162679 The headlamps will remain on for a period of time after you switch the ignition off.
Lighting When the headlamp switch is in the Autolamps position, the windshield wiper activated exterior lamps will turn on within 10 seconds when you switch the windshield wipers on. The exterior lamps will turn off approximately 60 seconds after you switch the windshield wipers off. Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting.
Lighting DAYTIME RUNNING LAMPS (If FRONT FOG LAMPS Equipped) WARNING Always remember to switch your headlamps on in low light situations or during inclement weather. The Daytime Running Lamp system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. E142453 Press the control to switch the fog lamps on or off.
Lighting • • • You open any door. You press a remote control button. You press switch B on the front interior lamp. With moonroof B A Front Interior Lamp Without moonroof C D C E142454 B (A) Door function switch. Press this switch to disable the interior E160819 lamps. The door function indicator lamp will illuminate yellow with lamps disabled. Press the switch again to turn interior lamps back on. The indicator lamp will illuminate blue. A E161163 (A) Door function switch.
Lighting AMBIENT LIGHTING (If Equipped) The ambient lighting system illuminates the interior with a choice of several colors. The ambient lighting control is located in the overhead console. A B C E142456 A Color palette B Control knob C Search mode Rotate B past the first detent to switch on and adjust to the desired brightness. Press A to cycle through the color choices. Press C to switch on all interior lamps and the ambient lighting.
Windows and Mirrors Window Lock POWER WINDOWS WARNINGS Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings. E70850 Press the control to lock or unlock the rear window controls. It will illuminate when the rear window controls are locked.
Windows and Mirrors 2. Close the window a third time to the point of resistance. The bounce-back feature is now disabled and you can close the window manually. The window will go past the point of resistance and you can close it fully. EXTERIOR MIRRORS Power Exterior Mirrors WARNING Do not adjust the mirrors when your vehicle is moving. See an authorized dealer as soon as possible if the window does not close after the third attempt.
Windows and Mirrors Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memory function. See Memory Function (page 114). Integrated Blind Spot Mirrors (If Equipped) C WARNING Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to increase your visibility along the side of your vehicle.
Windows and Mirrors Illuminated Vanity Mirror (If Equipped) Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night.
Windows and Mirrors Opening and Closing the Sunscreen Press and hold the front of the control within two seconds of a bounce-back event to override this function. While bounce-back is active, the closing force increases for each of the next three times that you close the moonroof. Venting the Moonroof Press and release the front of the control to vent the moonroof. Press and release the rear of the control to close the moonroof. E138668 Press and release the rear of the control to open the sunscreen.
Instrument Cluster GAUGES E171213 A Information display B Speedometer C Engine coolant temperature gauge D Fuel gauge E Tachometer Information Display Compass (If Equipped) Displays the vehicle’s heading direction. To calibrate and set the compass zone use the information display menu. See Information Displays (page 89). Use the diagram to determine your magnetic zone.
Instrument Cluster Fuel Gauge 3 2 1 Note: The fuel gauge level may vary slightly when your vehicle is moving or when driving on a slope. 15 4 14 13 5 Switch the ignition on. The fuel gauge will indicate approximately how much fuel is in the fuel tank. The arrow next to the fuel pump symbol shows the fuel filler door side of your vehicle. 12 Odometer The needle will move toward full when you refuel your vehicle. If the needle still points to empty after adding fuel, have your vehicle repaired.
Instrument Cluster Variations: Note: The low fuel warning and distance-to-empty warning can appear at different fuel gauge positions depending on fuel economy conditions. This variation is normal.
Instrument Cluster Fasten Safety Belt If it illuminates when you are driving, check that the parking brake is not engaged. If the parking brake is not engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by your authorized dealer. It will illuminate and a chime will sound to remind you to fasten your safety belt. See Safety Belt Minder (page 31). Fog Lamps - Front (If Equipped) WARNING It will illuminate when you switch the front fog lamps on.
Instrument Cluster Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for I/M testing. See Emission Control System (page 135). It will also illuminate momentarily when you switch the ignition on to confirm the lamp is functional.
Instrument Cluster Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately.
Information Displays • GENERAL INFORMATION WARNING • Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible.
Information Displays 1 Trip 1 and 2 Distance to E Trip odometer Trip timer Instantaneous fuel Average fuel Ford EcoMode Anticipation Speed 2 Ford EcoMode Digital Speedo All Value - Distance to E, Trip odometer, Trip timer and Average fuel 1 See Trip Computer (page 91). 2 See Eco Mode (page 165). Information Intelligent 4WD MyKey Dist.
Information Displays Settings Distance Choose your applicable setting Temperature Choose your applicable setting Chimes Park Slot On or Off Convenience Auto engine off On or Off Compass Display On or Off Remote Start Climate Control Heater – A/C / Auto or Last Settings Front Defrost / Automatic or Off Rear Defrost / Automatic or Off Duration (5, 10 or 15 minutes) Quiet Start On/Off Restore Default System MyKey Create MyKey Hold OK to Create MyKey Traction Ctrl Always On or User Sele
Information Displays Distance to E Indicates the approximate distance the vehicle will travel on the fuel remaining in the tank. Changes in driving pattern may cause the value to vary. Trip Odometer Registers the distance traveled of individual journeys. Trip Timer Registers the time of individual journeys. E130248 Instantaneous Fuel Press the OK button to acknowledge and remove some messages from the information display.
Information Displays Airbag Message Message Indicator Action Airbag fault Service now Amber Displays when the system requires service due to a malfunction. Contact your authorized dealer. Message Message Indicator Action Alarm activated Check Vehicle Amber Displays when the alarm has been triggered due to unauthorized entry. See Anti-Theft Alarm (page 65). Alarm fault Service required - Displays when the system requires service due to a malfunction. Contact your authorized dealer.
Information Displays Battery and Charging System Message Message Indicator Action Electrical system overvoltage Stop safely Red Stop your vehicle as soon as it is safe to do so and switch off the ignition. Contact your authorized dealer. Battery low See manual Amber Displays to warn of a low battery condition. Turn off all unneeded electrical accessories. Contact your authorized dealer.
Information Displays Doors Message Message Indicator Action X door open Red Displays when the door(s) listed is not completely closed and the vehicle is moving. - Displays when the door(s) listed is not completely closed. Red Displays when the luggage compartment is not completely closed and the vehicle is moving. - Displays when the luggage compartment is not completely closed. Red Displays when the hood is not completely closed and the vehicle is moving.
Information Displays Hill Start Assist Message Message Indicator Action Hill start assist not available Amber Displays when hill start assist is not available. Contact your authorized dealer. See Hill Start Assist (page 147). Message Message Indicator Action Ford KeyFree Key inside vehicle Amber Displays to remind you that the key is in the trunk. See Keyless Starting (page 124). Ford KeyFree No key detected - Displayed if the key is not detected by the system. See Keyless Starting (page 124).
Information Displays Lighting Message Message Indicator Action Brake lamp Bulb fault - Displays when the brake lamp bulb has burned out. Contact your authorized dealer. Low beam Bulb fault - Displays when the low beam headlamp bulb has burned out. Contact your authorized dealer. Headlamp fault Service required Amber Displays when an electrical system problem occurs with the headlamp system. Contact your authorized dealer.
Information Displays Message Message Indicator Action MyKey Vehicle at Top Speed Amber Displays when a MyKey is in use and the MyKey speed limit is reached. MyKey Check Speed Drive Safely - Displays when MyKey is active. MyKey Buckle Up to Unmute Audio - Displays when a MyKey is in use and BeltMinder is activated. MyKey Park aid cannot be deactivated - Displays when a MyKey is in use and park aid is activated.
Information Displays Power Steering Message Message Indicator Action Steering loss Stop safely Red The power steering system is not working. Stop the vehicle a safe place. Contact your authorized dealer. Steering assist fault Service required Amber The power steering system is not working. Stop the vehicle a safe place. Contact your authorized dealer.
Information Displays Message Message Indicator Action Transmission Hot Wait ... - Transmission is hot. Wait as needed to let it cool. 4WD fault Service required Amber The system is not functioning correctly and defaulted to front-wheel drive. See your authorized dealer. See Using Four-Wheel Drive (page 141). 4WD Off Amber Displays when the system disables automatically and enters front-wheel drive only mode to protect driveline components. See Using FourWheel Drive (page 141).
Information Displays Tire Pressure Monitoring System Message Message Indicator Action Low Tire Pressure Amber Displays when one or more tires on your vehicle have low tire pressure. See Tire Pressure Monitoring System (page 253). Tire Pressure Monitor Fault Amber Displays when the tire pressure monitoring system is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer. See Tire Pressure Monitoring System (page 253).
Climate Control MANUAL CLIMATE CONTROL A B C D E E141421 A Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed. B Recirculated air: Press the button to switch between outside air and recirculated air. When recirculated air is selected, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may also reduce unwanted odors from entering your vehicle.
Climate Control AUTOMATIC CLIMATE CONTROL A B J E141422 A C I H G D E F AUTO and Driver temperature control: Press the button to turn on automatic operation. Select the desired temperature using the temperature control. The system adjusts fan speed, air distribution, air conditioning operation, and selects outside air or recirculated air to heat or cool the vehicle in order to maintain the desired temperature.
Climate Control Turn the control to increase or decrease the air temperature on the passenger side of the vehicle. This turns on dual zone mode. F Recirculated air: Press the button to switch between outside air and recirculated air. When you select recirculated air, the air currently in the passenger compartment recirculates. This may reduce the time needed to cool the interior (when used with A/C) and may reduce unwanted odors from entering your vehicle.
Climate Control Dual Zone Temperature Control Note: Do not place objects under the front seats as this may interfere with the airflow to the rear seats. Select a temperature for the passenger’s side using the rotary control on the passenger’s side. Single zone temperature control automatically switches off. The temperature on the driver’s side remains unchanged. You can now adjust the driver's side and passenger's side temperatures independently. The display shows the temperature settings for each side.
Climate Control Recommended Settings for Heating Vehicle with manual climate control Vehicle with automatic climate control 1 Adjust the fan speed to the second speed setting. Press the AUTO button. 2 Adjust the temperature control to the midway point of the hot settings. Set the temperature to 72°F (22°C) 3 Adjust the air distribution control to the floor and windshield air vents position.
Climate Control Vehicle Stationary for Extended Periods during Extreme High Ambient Temperatures Vehicle with manual climate control Vehicle with automatic climate control 1 Apply the parking brake. Apply the parking brake. 2 Move the transmission selector lever to position P. Move the transmission selector lever to position P. 3 Adjust the temperature control to the MAX A/C position. Press the MAX A/C button. 4 Adjust the fan speed to the lowest speed setting.
Climate Control Maximum Cooling Performance in Instrument Panel or Instrument Panel and Footwell Positions The heated mirrors remove ice, mist and fog when you switch on the heated rear window. 1. Adjust the temperature control to the lowest setting. 2. Press the A/C and recirculated air buttons. 3. Adjust the fan speed to the highest setting initially and then adjust it to suit the desired comfort level. CABIN AIR FILTER Note: Make sure you have a cabin air filter installed at all times.
Climate Control Heated and Cooled Devices You cannot adjust the system during remote start operation. Switch on the ignition to return the system to its previous settings. You can now make adjustments. You need to switch on certain vehicle-dependent features, such as: • Heated seats. • Heated mirrors. • Heated rear window. The climate control system controls other heated and cooled devices inside the vehicle.
Seats We recommend that you follow these guidelines: • Sit in an upright position with the base of your spine as far back as possible. • Do not recline the seat back more than 30 degrees. • Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. • Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 inches (25 centimeters) between your breastbone and the air bag cover.
Seats Rear center head restraint WARNINGS Install the head restraint properly to help minimize the risk of neck injury in the event of a crash. Note: Adjust the seatback to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position.
Seats Moving the Seat Backward and Forward Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until it locks. Folding the Head Restraint 1. Press and hold button E. 2. Pull it back up to reset. Tilting Head Restraints The front head restraints tilt for extra comfort. To tilt the head restraint, do the following: E163870 WARNING Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged.
Seats Recline Adjustment WARNING Do not place cargo or any objects behind the seatback before returning it to the original position. Pull on the seatback to make sure that it has fully latched after returning the seatback to its original position. An unlatched seat may become dangerous if you stop suddenly or have a crash. POWER SEATS (If Equipped) WARNINGS Do not adjust the driver's seat or seatback when your vehicle is moving.
Seats E138647 Power Lumbar (If Equipped) MEMORY FUNCTION (If Equipped) WARNINGS Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts. Do not use the memory function when your vehicle is moving. This feature will automatically recall the position of the driver's seat and power mirrors. The memory control is located on the driver’s door. You can save up to three memory position pre-sets.
Seats REAR SEATS E142554 Saving a Pre-Set Position 1. Switch the ignition on. 2. Adjust the seat and exterior mirrors to your desired position. 3. Press and hold the desired memory button until you hear a single chime. Recalling a Pre-Set Position Press and release the memory button associated with your desired driving position. The seat and mirrors will move to the position stored for that pre-set.
Seats REAR SEAT ARMREST (If Equipped) HEATED SEATS (If Equipped) WARNING People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
Universal Garage Door Opener (If Equipped) HomeLink Wireless Control System (If Equipped) The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. WARNING Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).
Universal Garage Door Opener (If Equipped) 3. Using both hands, simultaneously, press and hold the desired HomeLink button and the hand-held transmitter button. DO NOT release either one until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing indicates successful training. 4. Press and hold the HomeLink button you programmed for five seconds, then release.
Universal Garage Door Opener (If Equipped) A 1. Press and hold the outer two function buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly. 2. When the indicator lights flash, release the buttons. The codes for all buttons are erased. A. Red indicator light B. Green indicator light 1. Press and hold one of the buttons on the hand-held transmitter for 10 seconds. The indicator light will change from green to red and green. 2.
Universal Garage Door Opener (If Equipped) 1. Press and hold the previously programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green. 2. Press the same button twice to confirm the change. If done correctly the indicator light will turn green. 5. Press and hold the previously programmed button on the visor for 2 seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete.
Auxiliary Power Points 12 Volt DC Power Point • • • WARNING Do not plug optional electrical accessories into the cigar lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. • on the center console inside the center console storage bin on the rear of the center console (12V or 110V AC) in the rear cargo area (if equipped).
Auxiliary Power Points When the indicator light, located on the power point, is: • on — power point is working, ignition is on and a device is plugged in. • off — power point is off, ignition is off or no device is plugged in. • flashing — power point is in fault mode. The power point temporarily turns off power if the 150 watt limit is exceeded. It can also switch to a fault mode when it is overloaded, overheated, or shorted.
Storage Compartments CENTER CONSOLE Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. Available console features include: A B C E142433 A Cupholder B Storage compartment with auxiliary power point, auxiliary input jack, USB port and media hub C Auxiliary power point OVERHEAD CONSOLE E131605 Press near the rear edge of the door to open it.
Starting and Stopping the Engine GENERAL INFORMATION IGNITION SWITCH WARNINGS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, creating the risk of fire. E72128 0 (off) - The ignition is off.
Starting and Stopping the Engine Ignition Modes • • • Make sure the parking brake is on. Move the transmission selector lever to position P. Turn the ignition key to position II. If your vehicle is equipped with a keyless ignition, see the following instructions. Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. E142555 1. Fully press the brake pedal. 2. Turn the key to position III to start the engine. Release the key when the engine starts.
Starting and Stopping the Engine Once the engine has started, it remains running until you press the button, even if the system does not detect a valid key. If you open and close a door while the engine is running, the system searches for a valid key. You cannot restart the engine if the system does not detect a valid key within 20 seconds. 3-button remote Failure to Start If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure: 1. Fully press the brake pedal. 2.
Starting and Stopping the Engine Stopping the Engine When Your Vehicle is Moving You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: • You can reset the timer by interacting with your vehicle (such as pressing the brake pedal or accelerator pedal). • You can temporarily switch off the shutdown feature any time the ignition is on (for the current ignition cycle only). Use the information display to do so.
Starting and Stopping the Engine Guarding Against Exhaust Fumes The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source. WARNING If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately.
Starting and Stopping the Engine • • Make sure the system is unplugged and properly stowed before driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use. Make sure the heater system is checked for proper operation before winter. Using the Engine Block Heater Make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.0 kilowatt-hours of energy per hour of use.
Fuel and Refueling • SAFETY PRECAUTIONS WARNINGS Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. • Automotive fuels can cause serious injury or death if misused or mishandled.
Fuel and Refueling Choosing the Right Fuel (Flex Fuel Vehicles) FUEL QUALITY Note: Use of any fuel other than those recommended may cause vehicle damage, a loss of vehicle performance and repairs may not be covered under warranty. Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 85% ethanol (E-85) in your flex fuel vehicle (FFV). If your vehicle is flex fuel capable, it will have a yellow bezel placed over the fuel fill inlet.
Fuel and Refueling Refilling With a Portable Fuel Container Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as "Regular" with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended. Premium fuel will provide improved performance and is recommended for severe duty usage such as trailer tow.
Fuel and Refueling Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • • • • E157280 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel. Place approved fuel container on the ground. Do not fill a fuel container while it is in the vehicle (including the cargo area).
Fuel and Refueling If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after 4 or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. E154765 FUEL CONSUMPTION 4.
Fuel and Refueling Calculating Fuel Economy WARNINGS Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Fuel and Refueling An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. • • the fuel fill inlet may not have been properly closed See Refueling (page 133). driving through deep water—the electrical system may be wet. Do not make any unauthorized changes to your vehicle or engine.
Fuel and Refueling Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, your vehicle is not ready for I/M testing.
Transmission P (Park) AUTOMATIC TRANSMISSION This position locks the transmission and prevents the front wheels from turning. Come to a complete stop before putting your vehicle into and out of P (Park) WARNINGS Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.
Transmission To use SelectShift, move the gearshift lever into S (Sport). Use the +/- buttons on the side of your gearshift lever to manually change gears. • • WARNINGS When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure. Use wheel chocks if appropriate. Press the (+) button to upshift. Press the (-) button to downshift.
Transmission 5. While holding the white lever in the rear position, move the shifter from the park position. 6. Press the shifter bezel back into the top finish panel until it snaps back into position. 7. Apply the brake pedal, start the vehicle and release the parking brake. Note: See your authorized dealer as soon as possible if this procedure is used.
Four-Wheel Drive (If Equipped) Note: It is recommended that you reinstall the repaired tire or replace the tire as soon as possible. Major dissimilar tire sizes between the front and rear axles could cause system damage or default the system to front-wheel drive. PRINCIPLE OF OPERATION This system is a proactive system. It has the ability to anticipate wheel slip and transfer torque to the rear wheels before slip occurs.
Four-Wheel Drive (If Equipped) When driving at slow speeds off road under high load conditions, use a low gear when possible. Low gear operation will maximize the engine and transmission cooling capability. in loss of vehicle control. Apply smooth pressure to the accelerator pedal or brake pedal when changes in vehicle speed are required. Avoid abrupt steering, acceleration and braking. This could result in an increased risk of vehicle roll over, loss of vehicle control and personal injury.
Four-Wheel Drive (If Equipped) Avoid driving at excessive speeds, this causes vehicle momentum to work against you and your vehicle could become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Driving on Hilly or Sloping Terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down.
Four-Wheel Drive (If Equipped) Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral. Disengage overdrive or move the transmission selector lever to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. The front wheels have to be turning in order to steer your vehicle. Avoid sudden braking.
Four-Wheel Drive (If Equipped) We recommend that you use caution when your vehicle has either a high load or device (i.e. ladder or luggage racks). Any modifications to your vehicle that raise the center of gravity may cause your vehicle to roll over when there is a loss of vehicle control. Failure to maintain your vehicle correctly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect you and your passenger's safety.
Brakes Emergency Brake Assist GENERAL INFORMATION Emergency brake assist detects when you brake heavily by measuring the rate at which you press the brake pedal. It provides maximum braking efficiency as long as you press the pedal. Emergency brake assist can reduce stopping distances in critical situations. Note: Occasional brake noise is normal.
Brakes PARKING BRAKE WARNINGS If the engine is revved excessively, or if a malfunction is detected, the system will be deactivated. WARNING Always set the parking brake fully and leave your vehicle with the transmission selector lever in position P. The system makes it easier to pull away when your vehicle is on a slope without the need to use the parking brake. When the system is active, your vehicle will remain stationary on the slope for two to three seconds after you release the brake pedal.
Traction Control System Indicator Lights and Messages PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. WARNING If a failure has been detected within the AdvanceTrac system, the stability control light will illuminate steadily. Verify that the AdvanceTrac system was not manually disabled through the information display. If the stability control light still illuminates steadily, have the system serviced by an authorized dealer immediately.
Stability Control The AdvanceTrac with Roll Stability Control system helps you keep control of your vehicle when on a slippery surface. The electronic stability control portion of the system helps avoid skids and lateral slides and roll stability control helps avoid a vehicle rollover. The traction control system helps avoid drive wheel spin and loss of traction. See Using Traction Control (page 148).
Stability Control USING STABILITY CONTROL AdvanceTrac® with Roll Stability Control™ (RSC®) The system automatically activates when you start your vehicle. The AdvanceTrac with RSC system cannot be completely turned off, but the electronic stability control and roll stability control portions of the system are disabled when the transmission is in position R. You can turn off the traction control portion of the system independently. See Using Traction Control (page 148).
Parking Aids Note: If your vehicle is equipped with MyKey®, it is possible to prevent turning the sensing system off. See MyKey™ (page 48). PARKING AID (If Equipped) WARNINGS To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds.
Parking Aids A A E130178 A Coverage area of up to 6 feet (1.8 meters) from the rear bumper. There is decreased coverage area at the outer corners of the bumper.
Parking Aids The system may not function correctly if something passes between the front bumper and the parking space (i.e. a pedestrian or cyclist) or if the edge of the neighboring parked vehicle is high from the ground (i.e. a bus, tow truck or flatbed truck). For specific information on the reverse sensing portion of the system, refer to that section. Note: The sensors may not detect objects in heavy rain or other conditions that cause disruptive reflections.
Parking Aids Press the button. The touch screen displays a message and a corresponding graphic to indicate it's searching for a parking space. Use the turn signal to indicate which side of the vehicle you want the system to search on. Note: If the turn signal is not on, the system automatically searches on the vehicle's passenger side. A E130107 Automatic Steering into Parking Space When a suitable space is found, the touch screen displays a message and a chime sounds.
Parking Aids E130108 When you think the vehicle has enough space in front and behind it, or you hear a solid tone from the parking aid, bring the vehicle to a complete stop. E130109 • When automatic steering is finished, the touch screen displays a message indicating that the active park assist process is done. The driver is responsible for checking the parking job and making any necessary corrections before putting the transmission in P (Park).
Parking Aids If a problem occurs with the system, a warning message is displayed, followed by a chime. Occasional system messages may occur in normal operation. For recurring or frequent system faults, contact an authorized dealer to have your vehicle serviced.
Parking Aids The system does not position the vehicle where I want in the space A parked vehicle has a high attachment (i.e. salt sprayer, snowplow, moving truck bed, etc.) The parking space length or position of parked objects changed after your vehicle passed The temperature around your vehicle changes quickly (i.e.
Parking Aids Note: If the transmission is in R (Reverse) and the luggage compartment is ajar, no rear view camera features are displayed. A B C D E Note: If the image comes on while the transmission is not in R (Reverse), have the system inspected by your authorized dealer. Note: When towing, the camera only sees what is being towed behind your vehicle. This might not provide adequate coverage as it usually provides in normal operation and some objects might not be seen.
Parking Aids Always use caution while reversing. Objects in the red zone are closest to your vehicle and objects in the green zone are farther away. Objects are getting closer to your vehicle as they move from the green zone to the yellow or red zones. Use the side view mirrors and rear view mirror to get better coverage on both sides and rear of the vehicle. This allows you to get a closer view of an object behind the vehicle. The zoomed image keeps the bumper in the image to provide a reference.
Cruise Control - Vehicles With: Cruise Control Switching Cruise Control On PRINCIPLE OF OPERATION Press and release ON. Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h). The indicator will display in the instrument cluster. E71340 Setting a Speed 1. Accelerate to the desired speed. 2. Press and release SET+. 3. Take your foot off the accelerator pedal.
Driving Aids BLIND SPOT INFORMATION SYSTEM (If Equipped) Cross Traffic Alert warns you of vehicles approaching from the sides when the transmission is in Reverse (R). Blind Spot Information System (BLIS®) with Cross Traffic Alert (If Note: The Blind Spot Information System does not prevent contact with other vehicles or objects; nor detect parked vehicles, people, animals or infrastructure (fences, guardrails, trees, etc.). It only alerts you to vehicles in the blind zones.
Driving Aids E142440 In this first example, the left sensor is only partially obstructed; zone coverage is nearly maximized. E142441 Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited.
Driving Aids System Lights and Messages Note: It is possible to get a blockage warning with no blockage present; this is rare and known as a false blockage warning. A false blocked condition either self-corrects or clears after a key cycle. E142442 The Blind Spot Information and Cross Traffic Alert systems illuminate a yellow alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from.
Driving Aids • Reasons for messages being displayed • The radar Clean the fascia area in surface is front of the radar or remove dirty or the obstruction. obstructed The radar surface is not dirty or obstructed Drive normally in traffic for a few minutes to allow the radar to detect passing vehicles so it can clear the blocked state. Heavy rainfall or snowfall interferes with the radar signals No action required.
Driving Aids Anticipation ECO MODE Adjust your vehicle speed and the distance to other vehicles to avoid the need for heavy braking or acceleration to improve fuel economy. This system assists you in driving more efficiently by constantly monitoring characteristics of gear changing, anticipation of traffic conditions and speeds while driving. Efficient speed The value of these characteristics is represented by petals shown in the display, with five petals being the most efficient.
Driving Aids WARNINGS off the engine. After at least 10 seconds, reset the system by restarting the engine, and watch the information display for a steering message. If a steering message returns, or returns while driving, take the vehicle to your dealer to have it checked. Obtain immediate service if a system error is detected. You may not notice any difference in the feel of your steering, but a serious condition may exist. Failure to do so may result in loss of steering control.
Load Carrying Adjustable Load Floor (If Equipped) REAR UNDER FLOOR STORAGE Passenger Compartment Floor E142446 Vehicles with the standard size spare tire can adjust the load floor to two positions. The front of the load floor can be placed either on (for high position) or below (for low position) the ledges behind the rear seats. The rear of the load floor always sits on the two small shelves located on the liftgate trim.
Load Carrying Note: Never place loads directly on the roof panel. The roof panel is not designed to directly carry a load. For correct roof rack system function, you must place loads directly on crossbars affixed to the roof rack side rails. When using the roof rack system, we recommend you use Ford Genuine Accessory crossbars designed specifically for your vehicle. Make sure that you securely fasten the load. Check the tightness of the load before driving and at each fuel stop.
Load Carrying vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label: Base Curb Weight - is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment.
Load Carrying PAYLOAD E143816 authorized-dealer installed equipment on the vehicle, you must subtract the weight of the equipment from the payload listed on the Tire Label in order to determine the new payload. Payload - is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver door (vehicles exported outside the US and Canada may not have a Tire Label).
Load Carrying Example only: E142516 E142517 CARGO E143817 171 Escape (TM2) , enUSA
Load Carrying Cargo Weight - includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) - is the total weight placed on each axle (front and rear) including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) - is the maximum allowable weight that can be carried by a single axle (front or rear).
Load Carrying Example only: E142523 E142524 WARNING Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.
Load Carrying GCW GVW E143819 or external) and a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer). Consult an authorized dealer (or the RV and Trailer Towing Guide available at an authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight - refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5000 pound (2268 kilogram) conventional trailer, multiply 5000 by 0.10 and 0.
Load Carrying 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400-750 (5 x 150) = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6.
Load Carrying - 150 = 150 pounds. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635 kilograms - (5 x 99 kilograms) (5 x 13.5 kilograms) = 635 - 495 67.5 = 72.5 kilograms. *Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past two years.
Towing TOWING A TRAILER Load Placement WARNINGS Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest to the trailer floor.
Towing Note: Be sure to take into consideration trailer frontal area. 2 Do not exceed 20 feet (1.86 2 meters ) if your vehicle is not equipped with a towing package or 2 2 30 feet (2.79 meters ) if your vehicle is equipped with a towing package. Note: For high altitude operation, reduce the gross combined weight by 2% per 1000 feet (300 meters) starting at the 1000 foot (300 meter) elevation point. Note: Certain states require electric trailer brakes for trailers over a specified weight.
Towing Maximum GCWR Maximum trailer 1 weight 2.5L 2WD 5351 lb (2427 kg) 1500 lb (681 kg) 1.6L GTDI 2WD 5862 lb (2659 kg) 2000 lb (907 kg) 2 5957 lb (2702 kg) 2000 lb (907 kg) 3 7457 lb (3382 kg) 3500 lb (1588 kg) 6005 lb (2724 kg) 2000 lb (907 kg) 2 6091 lb (2763 kg) 2000 lb (907 kg) 3 7591 lb (3443 kg) 3500 lb (1588 kg) Powertrain 2.0L GTDI 2WD 2.0L GTDI 2WD 1.6L GTDI 4WD 2.0L GTDI 4WD 2.0L GTDI 4WD 1 Calculated with SAE J2807 method. 2 Without trailer towing package.
Towing Trailer Brakes ESSENTIAL TOWING CHECKS WARNING Follow these guidelines for safe towing: • Do not tow a trailer until you drive your vehicle at least 1000 miles (1600 kilometers). • Consult your local motor vehicle laws for towing a trailer. • See the instructions included with towing accessories for the proper installation and adjustment specifications. • Service your vehicle more frequently if you tow a trailer. See your scheduled maintenance information.
Towing Before Towing a Trailer 1. Turn the steering wheel to point your vehicle tires away from traffic flow. 2. Set your vehicle parking brake. 3. Place the automatic transmission in position P. 4. Place wheel chocks in front and back of the trailer wheels. (Chocks not included with vehicle.) Practice turning, stopping and backing up to get the feel of your vehicle-trailer combination before starting on a trip. When turning, make wider turns so the trailer wheels clear curbs and other obstacles.
Towing Recovery Hook Location TRANSPORTING THE VEHICLE If your vehicle is equipped with a screw-in recovery hook, it is located in the luggage compartment under the floor cover. If your vehicle is not equipped with a recovery hook, you can purchase one from your dealer. Installing the Recovery Hook There is an installation point for the recovery hook located behind the fascia. Note: The screw-in recovery hook has a left-hand thread. Turn it counterclockwise to install it.
Towing It is acceptable to have your front-wheel drive vehicle towed from the front if using proper wheel lift equipment to raise the front wheels off the ground. When towing in this manner, the rear wheels can remain on the ground. Recreational Towing Front-wheel drive vehicles must have the front wheels placed on a tow dolly when towing your vehicle from the rear using wheel lift equipment. This prevents damage to the transmission.
Driving Hints Avoid these actions; they reduce your fuel economy: • Sudden accelerations or hard accelerations. • Revving the engine before turning it off. • Idle for periods longer than one minute. • Warm up your vehicle on cold mornings. • Use the air conditioner or front defroster. • Use the speed control in hilly terrain. • Rest your foot on the brake pedal while driving. • Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.
Driving Hints • • • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation. Close the windows for high-speed driving. FLOOR MATS DRIVING THROUGH WATER Note: Driving through deep water above the recommended levels can cause vehicle damage.
Driving Hints To install the floor mats, position the floor mat eyelet over the retention post and press down to lock in position. Remove in reverse order.
Roadside Emergencies Trailers shall be covered up to $200 if the disabled eligible vehicle requires service at the nearest authorized dealer. If the trailer is disabled, but the towing vehicle is operational, the trailer does not qualify for any roadside services. ROADSIDE ASSISTANCE Vehicles Sold In The U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Roadside Emergencies For vehicles equipped with a push button start system: 1. Press the START/STOP button to switch off the ignition. 2. Press the brake pedal and press the START/STOP button to start the vehicle. 3. Remove your foot from the brake pedal and press the START/STOP button to switch off the ignition. 4.
Roadside Emergencies Preparing Your Vehicle Note: Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. 1 Note: Use only a 12-volt supply to start your vehicle. Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle's electrical system.
Roadside Emergencies Jump Starting 2. Remove the jumper cable on the negative (-) terminal of the booster vehicle's battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery. 1. Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000 rpms, as shown in your tachometer. 2.
Customer Assistance These are some of the items that can be found online: • U.S. dealer locator by Dealer Name, City/State, or Zip Code • Owner Manuals • Maintenance Schedules • Recalls • Ford Extended Service Plans • Ford Genuine Accessories • Service specials and promotions. GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer.
Customer Assistance In order to help you serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. • Your telephone number (home and business). • The name of the authorized dealer and city where located. • The vehicle’s current odometer reading. California Civil Code Section 1793.
Customer Assistance already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.
Customer Assistance In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada.
Customer Assistance FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: +971 4 3326084 Toll-Free Number of the Kingdom of Saudi Arabia: 800 8971409 Local Telephone Number of Kuwait: 24810575 FAX: +971 4 3327299 Email: menacac@ford.com www.me.ford.com Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.
Customer Assistance To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Fuses FUSE SPECIFICATION CHART WARNINGS To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. Pre-Fuse Box The pre-fuse box is in the engine compartment attached to the positive battery post. This box contains several high current fuses. If you need to replace one of these high current fuses, see an authorized dealer. The power distribution box is in the engine compartment.
Fuses Fuse or relay number Fuse amp rating Protected components F7 40A** Anti-lock brake system and electronic stability program pump F8 30A** Electronic stability program valve F9 — F10 40A** Heater blower motor F11 30A** Body control module feed F12 30A** Powertrain control module relay fuse F13 30A** Starter relay F14 25A** Rear power window (without door control unit) F15 20A** Front cigar lighter or power outlet F16 25A** Front power window (without door control unit) F
Fuses Fuse or relay number Fuse amp rating Protected components F30 — Not used F31 — Not used F32 15A* Vehicle power F33 10A* Vehicle power 2 F34 10A* Vehicle power 3 F35 15A* Vehicle power 4 F36 5A* Active grill shutters F37 10A* Occupant classification sensor, Passenger airbag deactivation indicator feed F38 5A* Engine control module and transmission control module ignition feed F39 5A* Daytime running lamps and headlamp control module ignition feed F40 5A* Electronic po
Fuses Fuse or relay number Fuse amp rating R7 — R8 Mini relay R9 — Protected components Not used Delayed accessory relay Not used R10 Mini relay R11 Micro relay Starter relay Air conditioner clutch R12 Power relay Cooling fan R13 Mini relay Heater blower R14 Mini relay Engine control relay R15 Power relay Heated rear window R16 Power relay Ignition 15 *Mini fuses **Cartridge fuses Passenger Compartment Fuse Panel The fuse panel is on the right side below the glove box.
Fuses E129926 Fuse or relay number Fuse amp rating Protected components F56 20A F57 — Not used F58 5A Not used (spare) F59 5A Passive anti-theft transceiver F60 10A Interior light, Driver door switch pack, Glove box illumination, Overhead console switch bank F61 20A Cigar lighter, Power point Fuel pump supply, Air mass meter 201 Escape (TM2) , enUSA
Fuses Fuse or relay number Fuse amp rating Protected components F62 5A Rain sensor module, Auto-dimming mirror F63 10A Not used (spare) F64 — Not used F65 10A Liftgate release F66 20A Driver door unlock supply F67 7.5A SYNC, Multifunction display, Global positioning system module F68 — Not used F69 5A Instrument cluster F70 20A Central lock and unlock supply F71 10A Heating control head (manual air conditioner), Dual electronic automatic temperature control F72 7.
Fuses Fuse or relay number Fuse amp rating Protected components F86 10A Air bag module, Occupant classification system, Passenger air bag deactivation indicator F87 7.5A Not used (spare) F88 25A Supply for F67, F69, F71 and F79 F89 — Not used Luggage Compartment Fuse Panel The fuse panel is in the luggage compartment behind the passenger side wheel well. Remove the fuse panel cover to gain access to the fuses.
Fuses Fuse or relay number Fuse amp rating Protected components F8 — F9 25A Driver seat motor F10 5A Driver seat memory module logic feed Not used F11 5A Rear ignition coil feed F12 — Not used F13 — Not used F14 — Not used F15 — Not used F16 — Not used F17 — Not used F18 — Not used F19 — Not used F20 — Not used F21 — Not used F22 — Not used F23 25A Audio amplifier F24 30A DC/AC power converter F25 25A Power liftgate F26 40A Accessories, Trailer tow
Fuses Fuse or relay number Fuse amp rating Protected components F34 20A Driver seat heater F35 20A Passenger seat heater F36 — Not used F37 — Not used F38 — Not used F39 — Not used F40 — Not used F41 — Not used F42 — Not used F43 — Not used F44 — Not used F45 — Not used F46 — Not used R1 Power relay R2 — Not used Rear 15 relay R3 — Not used R4 — Not used R5 — Not used R6 — Not used CHANGING A FUSE Fuses E142430 WARNING If electrical components in
Fuses Standard Fuse Amperage Rating and Color Color Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey - - - 3A Violet Violet - - - 4A Pink Pink - - - 5A Tan Tan - - - 7.
Maintenance Working with the Engine Off GENERAL INFORMATION Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key (if equipped). 3. Block the wheels. 1. Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers that are there to help you with their professional servicing expertise.
Maintenance E142458 3. Move the catch to the right to release the hood. E87786 4. Open the hood and support it with the hood strut. Closing the Hood 1. Remove the hood strut from the catch and secure it correctly in the clip. 2. Lower the hood and allow it to drop under its own weight for the last 8-12 in (20-30 cm). Note: Make sure that the hood is correctly closed.
Maintenance UNDER HOOD OVERVIEW - 1.
Maintenance UNDER HOOD OVERVIEW - 2.
Maintenance UNDER HOOD OVERVIEW - 2.
Maintenance 1. Make sure that your vehicle is on level ground. 2. Turn the engine off and wait 10 minutes for the oil to drain into the oil pan. 3. Remove the dipstick and wipe it with a clean, lint-free cloth. Replace the dipstick and remove it again to check the oil level. ENGINE OIL DIPSTICK - 2.0L ECOBOOST™/2.5L A B If the level is at the MIN mark, add oil immediately. Adding Engine Oil Note: Do not remove the filler cap when the engine is running.
Maintenance Note: Make sure that the level is between the MIN and MAX marks on the coolant reservoir. 1. Remove the filler cap. 2. Add engine oil that meets the Ford specifications. See Capacities and Specifications (page 262). 3. Replace the filler cap. Turn it until you feel a strong resistance. Note: Coolant expands when it is hot. The level may extend beyond the MAX mark Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately.
Maintenance • WARNINGS To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. Do not add coolant further than the MAX mark. • Note: Do not use stop leak pellets, cooling system sealants, or additives as they can cause damage to the engine cooling or heating systems.
Maintenance Recycled Engine Coolant What You Should Know About FailSafe Cooling Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
Maintenance When Fail-Safe Mode Is Activated AUTOMATIC TRANSMISSION FLUID CHECK WARNINGS Fail-safe mode is for use during emergencies only. Operate your vehicle in fail-safe mode only as long as necessary to bring your vehicle to rest in a safe location and seek immediate repairs.
Maintenance WASHER FLUID CHECK CHANGING THE 12V BATTERY WARNING WARNINGS Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation. If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection.
Maintenance When a low voltage battery replacement is necessary, see an authorized dealer to replace the low voltage battery with a Ford recommended replacement low voltage battery that matches the electrical requirements of the vehicle presets, are also maintained in memory by power from the low voltage battery. When a technician disconnects and connects the low voltage battery, these settings are erased.
Maintenance Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. 1 Note: It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. 1 2 E129990 CHECKING THE WIPER BLADES 2. Press the locking buttons together. 3.
Maintenance 2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height. Note: To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 5. Install in the reverse order. Note: Make sure that the wiper blade locks into place. Replace wiper blades at least once per year for optimum performance.
Maintenance 5. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver, turn the adjuster either clockwise or counterclockwise in order to aim the headlamp. The horizontal edge of the brighter light should touch the horizontal reference line. 6. Close the hood and turn off the lamps. Vehicles With High Intensity Discharge Headlamps E142467 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. 2.
Maintenance Replacing Headlamp Bulbs 3. Carefully pull the headlamp assembly as far as possible towards the front of the vehicle to disengage it from the lower fixing point. 4. Carefully lift the outer side of the headlamp and remove it. 5. Disconnect the electrical connector. WARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb by only its plastic base and do not touch the glass.
Maintenance 1. 2. 3. 4. Replacing Side Marker Bulbs Remove the headlamp. Remove service cap. Disconnect the electrical connector. Remove bulb from the headlamp assembly by turning it counterclockwise, then pull it straight out. Low beam headlamp: 2 4 E142472 1. Remove the bulb socket from the headlamp assembly by turning it counterclockwise. 2. Remove the bulb by gently pull the bulb straight out of the socket. Install the new bulb in reverse order. E142471 1. 2. 3. 4.
Maintenance Replacing Tail, Brake and Turn Signal Bulbs 2 E142798 1. Remove the screws from the splash shield at the wheel well to gain access to the lamp assembly. 3 E142473 1. Make sure the headlamp control is in the off position and open the liftgate. 2. Remove the two bolt covers using a standard flat tip screwdriver. 3. Remove the two bolts from the lamp assembly. 4. Gently pull the lamp assembly away from the vehicle. E142799 2.
Maintenance 6. Remove the turn signal bulb or the tail and brake bulb by turning the bulb socket counterclockwise. Gently pull the bulb straight out of the socket. 2. Remove the lamp. 3. Remove the bulb. Install the new bulb in reverse order. Replacing High-Mount Brake Lamp Bulb Reverse steps to reinstall bulb. Replacing Reverse Lamp Assembly Your vehicle is equipped with an LED center high-mount stop lamp located in the spoiler. It is designed to last the life of the vehicle.
Maintenance Function Trade number Turn lamp - rear T20 Backup lamp 921 License plate lamp W5W * High-mount brake lamp LED * Interior lamps LED * To replace these lamps - see your authorized dealer.
Maintenance 2. Remove the air filter element from the air filter housing. 3. Wipe any dirt or debris from the air cleaner assembly to make sure no dirt gets in the engine and to make sure you have a good seal. CHANGING THE ENGINE AIR FILTER WARNING To reduce the risk of vehicle damage and personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. When changing the air filter element, use only the air filter element listed.
Maintenance 2.5L Engine E142711 1. 2. 3. 4. 5. 6. Detach the 2 clips that secure the air filter cover to the housing. Carefully remove the air filter cover from the housing. Do not detach any connections or tubes from the cover. Remove the air cleaner from the housing. Wipe any dirt or debris from the air filter housing and cover to make sure that no dirt gets into the engine. Load the air filter into the housing. Replace the air filter cover and secure the clips.
Vehicle Care GENERAL INFORMATION CLEANING THE EXTERIOR Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash.
Vehicle Care • • • • Wash your vehicle first, using cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash. Use Motorcraft Custom Bright Metal Cleaner. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag. • • • • Do not apply cleaning product to hot surfaces and do not leave cleaning product on chrome surfaces longer than the time recommended.
Vehicle Care • • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations. Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine. WARNINGS On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.
Vehicle Care Clean the instrument panel and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • • • • 4. Remove the soaked cloth and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth. Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel.
Vehicle Care • REPAIRING MINOR PAINT DAMAGE Authorized dealers have touch-up paint to match your vehicle’s color. Your vehicle color code is printed on a sticker on the front, left-hand side door jamb. Take your color code to your authorized dealer to make sure you get the correct color. • • Before repairing minor paint damage, use a cleaner such as Motorcraft Bug and Tar Remover to remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout.
Vehicle Care • • • • • Battery Touch-up exposed or primed metal to prevent rust. Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when your vehicle is washed. Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil. Cover interior trim to prevent fading. Keep all rubber parts free from oil and solvents. • • Note: If battery cables are disconnected, it will be necessary to reset memory features.
Vehicle Care • • • Check brake pedal operation. Drive your vehicle 15 feet (4.5 meters) back and forth to remove rust build-up. Check fluid levels (including coolant, oil and gas) to make sure there are no leaks, and fluids are at recommended levels. If the battery was removed, clean the battery cable ends and inspect. Contact your authorized dealer if you have any concerns or issues.
Wheels and Tires Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Wheels and Tires How your vehicle differs from other vehicles Sport utility vehicles and trucks can differ from some other vehicles in a few noticeable ways. Your vehicle may be: E168583 As a result of the above dimensional differences, Sport utility vehicles and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
Wheels and Tires U.S. Department of Transportation Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. TIRE CARE Information About Uniform Tire Quality Grading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Wheels and Tires Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Wheels and Tires Information Contained on the Tire Sidewall *kPa: Kilopascal, a metric unit of air pressure. *PSI: Pounds per square inch, a standard unit of air pressure. *Cold tire pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mi (1.6 km).
Wheels and Tires G. H: Indicates the tire's speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h). These ratings are listed in the following chart.
Wheels and Tires Letter rating Speed rating - mph (km/h) W 168 mph (270 km/h) J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. K. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire.
Wheels and Tires *Traction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Wheels and Tires C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual, defined as four tires on the rear axle (a total of six or more tires on the vehicle). D. Maximum Load Single lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single, defined as two tires (total) on the rear axle. B A C D E Information on T Type Tires T145/80D16 is an example of a tire size.
Wheels and Tires C. 80: Indicates the aspect ratio which gives the tire's ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D. D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate.
Wheels and Tires (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door.
Wheels and Tires 3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pressing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T type mini-spare tires, see the Dissimilar spare wheel and tire assembly information for a description.
Wheels and Tires Tire Wear or suspected have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended. Age WARNING Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflation pressure) the tires experience throughout their lives.
Wheels and Tires describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Wheels and Tires It is recommended that the two front tires or two rear tires generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the tire pressure monitoring system indicator is flashing, your system is malfunctioning.
Wheels and Tires Driving habits have a great deal to do with your tire mileage and safety. Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically.
Wheels and Tires Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare wheel and tire assembly it is intended for temporary use only and should not be used in a tire rotation.
Wheels and Tires • • • As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.
Wheels and Tires Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Wheels and Tires Low tire pressure warning light Possible cause Customer action required Solid warning light Tire(s) under-inflated Make sure tires are at the proper pressure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off.
Wheels and Tires How Temperature Affects Your Tire Pressure Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. The tire pressure monitoring system monitors tire pressure in each pneumatic tire.
Wheels and Tires 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. • • 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY. The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking performance. • Comfort and noise.
Wheels and Tires WARNINGS If your vehicle slips off the jack, you or someone else could be seriously injured. Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. To lessen the risk of personal injury, do not put any part of your body under your vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Wheels and Tires 3. Stow the flat tire on the floor in the cargo area. Secure with the flat tire retainer strap by following the next steps: 10. Remove the lug nuts with the lug wrench. Note: If equipped with full wheel covers with exposed wheel nuts, remove the wheel nuts prior to removing the wheel cover or damage to the wheel cover may occur. 11. 12. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Wheels and Tires E143746 TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
Wheels and Tires E145950 A Wheel pilot bore Inspect the wheel pilot bore and mounting surface prior to installation. Remove any visible corrosion or loose particles.
Capacities and Specifications ENGINE SPECIFICATIONS Engine 1.6L EcoBoost engine 2.0L EcoBoost engine 2.5L engine Cubic inches 98 122 152 Required fuel Minimum 87 octane Minimum 87 octane Minimum 87 octane Compression ratio 10.0:1 9.3:1 9.7:1 Spark plug gap 0.027-0.031 in. (0.700.80 mm) 0.027-0.031 in. (0.70-0.80 mm) 0.049-0.053 in. (1.25-1.35 mm) Drivebelt Routing 1.6L engine E161372 2.0L and 2.
Capacities and Specifications A. Long drivebelt is on first pulley groove closest to engine B. Short drivebelt is on second pulley groove farthest from engine MOTORCRAFT PARTS Component Air filter element 1.6L EcoBoost® engine 2.0L EcoBoost® engine 2.
Capacities and Specifications Please note that in the graphic, XXXX is representative of your vehicle identification number.
Capacities and Specifications The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description.
Capacities and Specifications TECHNICAL SPECIFICATIONS WARNING The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.
Capacities and Specifications Item Capacity Engine oil 1.6L EcoBoost 4.3 qt (4.1 L) Engine oil 2.5L 5.7 qt (5.4 L) Engine coolant 2.0L EcoBoost 5 9.7 qt (9.2 L) Engine coolant 1.6L EcoBoost 5 8.5 qt (8 L) Engine coolant 2.5L 5 9.2 qt (8.7 L) Windshield washer fluid Fill as required Ford part name or equivalent Ford part number / Ford specification Motorcraft SAE 5WXO-5W20-QFS or 20 Full Synthetic XO-5W20-QSP Motor Oil or (U.S.
Capacities and Specifications Item Capacity A/C refrigerant 2.0L EcoBoost 1.7 lb (0.76 kg) A/C refrigerant compressor oil 4.5 fl oz (133 ml) Ford part name or equivalent Ford part number / Ford specification Motorcraft PAG Refrigerant Compressor Oil YN-12-D / WSHM1C231-B 1 Ford recommends using DOT 4 LV High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards.
Capacities and Specifications E142732 269 Escape (TM2) , enUSA
Audio System AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: • AM: 530, 540-1700, 1710 kHz • FM: 87.9-107.7, 107.9 MHz GENERAL INFORMATION Radio Frequencies and Reception Factors Radio Reception Factors Distance and Strength The further you travel from an FM station, the weaker the signal and the weaker the reception.
Audio System • • MP3 and WMA folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 and WMA tracks on the disc (noted by the MP3 or WMA file extension) and all folders containing MP3 and WMA files, from F001 (folder) T001 (track) to F253 T255. Creating discs with only one level of folders helps with navigation through the disc files.
Audio System E172881 A Eject: Press to eject a CD. B Cursor arrows: Press to scroll through on-screen audio system choices, menus or other on-screen functions. C CD slot: Insert a CD. D OK: Press to confirm menu selections. E Clock: Press to set the time. Use the cursor arrows to set the hours and minutes. Press OK to confirm the time. You can also set the clock by pressing MENU and scrolling to Clock Settings. F TUNE: Press to manually search the frequency band.
Audio System H Seek forward: Press and release the right side of the control to go to the next preset radio station or disc track. Press and hold this side of the control to fast forward or reverse to the next strong radio station, memory preset or through the current disc track. I ON/OFF: Press to switch the system on and off. Turn to adjust the volume. J Seek reverse: Press and release the left side of the control to go to the previous preset radio station or disc track.
Audio System A B C D E O N F M L K G H H J E162867 I A Eject: Press this button to eject a CD. B Cursor arrows: Press these buttons to scroll through on-screen audio system choices. C OK: Press this button to confirm menu selections. D INFO: Press this button to access any available radio or CD information. E TUNE - and TUNE +: Press these buttons to manually search the frequency band. F Number block: In radio mode, store your favorite radio stations.
Audio System J ON/OFF: Press this button to switch the system off and on. Turn to adjust the volume. K MENU: Press this button to access different audio system features. See Menu Structure later in this section. L SOUND: Press this button to access settings for Treble, Middle, Bass, Fade and Balance. Use the up and down arrow buttons to select the various settings. When you make your selection, press the left and right arrow buttons to change the settings. Press OK to set or press MENU to exit.
Audio System A B C D E P O F N M L G H H K E162869 J I A Eject: Press this button to eject a CD. B Cursor arrows: Press these buttons to scroll through on-screen audio system choices. C OK: Press this button to confirm menu selections. D INFO: Press this button to access any available radio or CD information. E TUNE - and TUNE +: Press these buttons to manually search the frequency band. F Number block: In radio mode, store your favorite radio stations.
Audio System I Sound: Press this button to access settings for Treble, Middle, Bass, Fade and Balance. Use the up and down arrow buttons to select the various settings. When you make your selection, press the left and right arrow buttons to change the settings. Press OK to set or press MENU to exit. Sound settings can be set for each audio source independently. J Seek: Press and release these buttons to go to the previous or next preset radio station or disc track.
Audio System E143843 A - TUNE +: Press this button to manually search through the radio frequency band. B ON/OFF and VOL: Press this button to switch the audio system off and on. Turn to adjust the volume. C Eject: Press this button to eject a CD. D SEEK: Press this button to go to the next station up or down the radio frequency band or the next or previous track on a CD. E SOUND: Press this button to adjust the sound settings for Bass, Treble, Balance and Fade.
Audio System Note: The CD slot is directly above the touchscreen. AUDIO UNIT - VEHICLES WITH: SONY AM/FM/CD Note: The MyFord Touch system controls most of the audio features. See Entertainment (page 342). WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Audio System D - TUNE +: In radio mode, press these buttons to manually search through the radio frequency band. In SIRIUS mode, press these buttons to find the next or previous available satellite radio station. E Volume: Turn this control to adjust the volume. F SOUND: Press this button to access settings for Treble, Midrange, Bass, Balance and Fade. G Eject: Press this button to eject a CD. Menu Structure Press the up and down arrow buttons to scroll through the options.
Audio System SIRIUS Set Category Select to view channel categories (such as Pop, Rock or News). If you select a category, seek and scan functions only stop on channels in that category. Alerts Select to turn off or turn on alerts for songs, artists or teams. The system alerts you when the selection is playing on another channel. Save up to 20 alerts. Unlock All Stations Use your PIN to unlock previously locked stations. Skip No stations Use to restore any channels you previously skipped.
Audio System Clock Settings Set Time Select to set the time. Set Date Select to set the calendar date. 24h Mode Select to view clock time in a 12-hour mode or 24-hour mode. Display Settings Dimming Select to change display brightness. Language Select to display the language in English, French or Spanish. Temp. setting Select to display the outside temperature in Fahrenheit or Celsius.
Audio System When HD Radio broadcasts are active, you can access the following functions: • Scan allows you to hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels. You may see the HD logo appear if the station has a digital broadcast. • Memory presets allow you to save an active channel as a memory preset. Touch and hold a memory preset slot until the sound returns.
Audio System Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required. This is a by the radio broadcaster. broadcast issue. Sound fading or blending in The radio is shifting between No action required. The and out. analog and digital audio. reception issue may clear up as you continue to drive. * There is an audio mute delay when selecting HD2 or HD3, multicast preset or Direct Tune.
Audio System Note: This receiver includes the eCos real-time operating system. eCos is published under the eCos License. Satellite Radio Reception Factors Potential satellite radio reception issues Antenna obstructions For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other material as far away from the antenna as possible.
Audio System Message When in satellite radio mode, select: Options Troubleshooting Message Condition Action Acquiring… Radio requires more than two seconds to produce audio for the selected channel. Satellite antenna fault There is an internal module If this message does not clear shortly, or with an ignior system failure present. tion key cycle, your receiver may have a fault. See an authorized dealer for service. SIRIUS system failure No action required. This message should disappear shortly.
Audio System The auxiliary input jack allows you to connect and play music from your portable music player through your vehicle speakers. You can use any portable music player designed for use with headphones. Your audio extension cable must have male 1/8th-inch (3.5 millimeter) connectors at each end. AUDIO INPUT JACK WARNINGS Driving while distracted can result in loss of vehicle control, crash and injury.
Audio System The USB port allows you to plug in media playing devices, memory sticks and charge devices (if supported). See SYNC™ (page 289). MEDIA HUB (If Equipped) The media hub is located in the center console and has the following features: C A B E142605 A A/V inputs B SD card slot C USB ports See MyFord Touch™ (page 324).
SYNC™ (If Equipped) GENERAL INFORMATION E142598 • SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist, Vehicle Health Report and SYNC Services (Traffic, Directions * & Information). • • • • Use the advanced voice recognition system Charge your USB device (if your device supports this).
SYNC™ (If Equipped) In Canada, call 1-800-565-3673. When using SYNC: • Do not operate playing devices if the power cords or cables are broken, split or damaged. Place cords and cables out of the way, so they do not interfere with the operation of pedals, seats, compartments or safe driving abilities. • Do not leave playing devices in your vehicle during extreme conditions as it could cause them damage. See your device's manual for further information. • Do not attempt to service or repair the system.
SYNC™ (If Equipped) System data cannot be accessed without special equipment and access to the vehicle's SYNC module. Ford Motor Company and Ford of Canada will not access the system data for any purpose other than as described absent consent, a court order, or where required by law enforcement, other government authorities, or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
SYNC™ (If Equipped) System Interaction and Feedback The default setting is to a higher level of interaction in order to help you learn to use the system. You can change these settings at any time. The system provides feedback through audible tones, prompts, questions and spoken confirmations depending on the situation and the chosen level of interaction (voice settings). You can customize the voice recognition system to provide more or less instruction and feedback.
SYNC™ (If Equipped) When you say: The system: "Media candidate lists off" Makes a best guess from the media candidate list. The system may occasionally ask you questions. "Media candidate lists on" Clarifies your voice command for media candidates. "Phone candidate lists off" Makes a best guess from the phone candidate list. The system may occasionally ask you questions.
SYNC™ (If Equipped) Pairing a Phone for the First Time 1. Note: SYNC can support downloading up to approximately 1000 entries per Bluetooth-enabled cellular phone. 2. 3. Note: Make sure to switch on the ignition and the radio. Put the transmission in position P. 4. Note: To scroll through the menus, press the up and down arrows on your audio system. 5. Wirelessly pairing your phone with SYNC allows you to make and receive hands-free calls. 6. 1. Press the phone button.
SYNC™ (If Equipped) "PHONE" "DIAL" 2 "Call history outgoing" "Connections" "Dial" "411 (four-one-one)", "911" (nine-oneone) 2 "700" (seven hundred) 1,3 "800" (eight hundred) "Go to privacy" "900" (nine hundred) "Hold" "Pound" (#) "Join" "Menu" "Number <0-9>" 2,4 "Phone book " "Asterisk" (*) 2 "Clear" (deletes all entered digits) "Delete" (deletes one digit) 2 "Phone book at home" "Plus" 2 "Phone book at office" "Phone book at work" "Star" 2 Note: To exit dia
SYNC™ (If Equipped) Receiving Calls "MENU" When receiving a call, you can: • Answer the call by pressing the phone button. • Reject the call by pressing and holding the phone button. • Ignore the call by doing nothing. "Signal" "Text message inbox" Words in ( ) are optional and do not have to be spoken for the system to understand the command.
SYNC™ (If Equipped) When you select: You can: 2. Access the desired contact through SYNC or use voice commands to place the second call. Once actively in the second call, press MENU. 3. Scroll to Join Calls, and press OK. Press OK again when Join Calls? appears. Phonebook Access your phonebook contacts. 1. Press OK to select, and then scroll through your phonebook contacts. 2. Press OK again when the desired selection appears in the display. 3. Press the phone button.
SYNC™ (If Equipped) When you select: You can: Note: The system attempts to automatically re-download your phonebook and call history each time your phone connects to SYNC (if the auto download feature is on and your Bluetooth-enabled cellular phone supports this feature). Access and call any contacts in your previously downloaded phonebook. 1. Press OK to confirm and enter. If your phonebook has fewer than 255 listings, they appear alphabetically in flat file mode.
SYNC™ (If Equipped) Text Messaging Sending, Downloading and Deleting Your Text Messages Note: This is a phone-dependent feature. Note: Forwarding a text message is a speed-dependent feature and is only available when your vehicle is traveling at 3 mph (5 km/h) or less. SYNC allows you to receive, send, download and delete text messages. The system can also read incoming text messages to you so that you do not have to take your eyes off the road. Note: You can only have one recipient per text message.
SYNC™ (If Equipped) 3. Press OK when the desired selection is in the display. 4. Enter the name of the recipient. Scroll to cycle through Phonebook or Call History entries. You can also select Enter Number to say the desired number. 5. Press OK to enter the desired menu and scroll to select the specific contact. 6. Press OK when the contact appears and press OK again to confirm when the system asks if you would like to send the message.
SYNC™ (If Equipped) When you select: You can: If your phone supports in-band ringing, your phone's ring tone plays when you choose Phone Ringer. Message Notification Have the option of hearing an audible tone to notify you when a text message arrives. 1. Press OK to select and scroll between Message Notification On and Message Notification Off. 2. Press OK to select. Modify Phonebook Modify the contents of your phonebook (such as add, delete or download).
SYNC™ (If Equipped) 3. Scroll to Bluetooth Devices. Press OK. 1. Press the phone button to enter the phone menu 2. Scroll to System Settings. Press OK. 4. Scroll to select from the following options: If you select: You can: Add Bluetooth Device See Using SYNC™ With Your Phone (page 293). Connect Bluetooth Device Connect a previously paired Bluetooth-enabled phone. 1. Press OK to select and view a list of previously paired phones. 2.
SYNC™ (If Equipped) Advanced 1. Press the phone button to enter the phone menu 2. Scroll to System Settings. Press OK. 3. Scroll to Advanced. Press OK. 4. Scroll to select from the following options: The Advanced menu allows you to access and set prompts, languages, defaults, perform a master reset, install an application and view system information. If you select: You can: Prompts Get help from SYNC by using questions, helpful hints or asking you for a specific action.
SYNC™ (If Equipped) If you select: You can: Press OK to select. MAP Profile This is a Bluetooth component, which can further help your phone with the exchange of text messages. Return Exit the current menu. WARNINGS SYNC™ APPLICATIONS AND SERVICES Do not wait for 911 Assist to make an emergency call if you can do it yourself. Dial emergency services immediately to avoid delayed response time which could increase the risk of serious injury or death after a crash.
SYNC™ (If Equipped) • If a crash deploys an airbag (excluding knee airbags and rear inflatable safety belts [if equipped]) or activates the fuel pump shut-off, your SYNC-equipped vehicle may be able to contact emergency services by dialing 911 through a paired and connected Bluetooth-enabled phone. You can learn more about the 911 Assist feature, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • • • See Supplementary Restraints System (page 34).
SYNC™ (If Equipped) Note: Your Vehicle Health Report feature requires activation before use. Visit www.SYNCMyRide.com to register. There is no fee or subscription associated with Vehicle Health Report, but you must register to use this feature. 911 Assist May Not Work If • • • Your cellular phone or 911 Assist hardware sustains damage in a crash. The vehicle's battery or the SYNC system has no power. The phone(s) thrown from your vehicle are the ones paired and connected to the system.
SYNC™ (If Equipped) 3. Scroll to select from the following options: 1. Press the phone button to enter phone menu. 2. Scroll to select Vehicle Health, and then press OK. Vehicle health report options User Preferences: Press OK Automatic Reports: Press OK to and select On or Off. to select and enter the Select On to have SYNC automatically prompt you to run menu. Scroll to select from: a health report at certain mileage intervals.* Mileage Intervals: Press OK.
SYNC™ (If Equipped) Note: SYNC Services requires activation before use. Visit www.SYNCMyRide.com to register and check your eligibility for complimentary services. Standard phone and message rates may apply. Subscription may be required. You must also have the active SYNC Services Bluetooth-enabled cellular phone paired and connected to the system in order to connect to, and use, SYNC Services. See Using SYNC™ With Your Phone (page 293).
SYNC™ (If Equipped) Connecting to SYNC Services Using the Phone Menu 1. 2. 3. 4. 5. 6. assist you by searching for businesses by name or by category, residential addresses by street address or by name or specific street intersections. Operator Assist is a feature of your SYNC Services subscription. For more information on Operator Assist, visit www.SYNCMyRide.com/support. 2. Follow the voice prompts to select your destination.
SYNC™ (If Equipped) SYNC Services quick tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information. You can save address points such as work or home. You can also save favorite information like sports teams or a news category. You can learn more about personalization by logging onto www.SYNCMyRide.com.
SYNC™ (If Equipped) 4. Scroll to USB. Press OK. 5. Depending on how many digital media files are on your connected device, Indexing may appear in the radio display. When indexing is complete, the screen returns to the Play menu.
SYNC™ (If Equipped) 1 is a dynamic listing, meaning that it could be the name of anything, such as a group, artist or song. "USB" "Similar music" 2 This voice command is not available until indexing is complete. "What's playing?" 3 This voice command is only available in folder mode. Voice command guide "Autoplay" Turn autoplay on to listen to music processed during indexing. Turn autoplay off to allow the indexing process to finish before the system plays any of your music.
SYNC™ (If Equipped) Media Menu Features and also to add, connect or delete devices. The media menu allows you to select your media source, how to play your music (such as by artist, genre, shuffle or repeat), Press AUX and then MENU to enter the media menu. 2. Scroll to cycle through: 1. When you select: You can: Play Menu Play your music by artist, album, genre, playlist, track, similar music or play all music.
SYNC™ (If Equipped) When you select: You can: System Settings Access Bluetooth Device menu listings (Add, Connect, Set as Primary, On and Off, Delete) as well as Advanced menu listings (prompts, languages, defaults, master reset, install application and system information). Exit Media Menu Press OK to exit the media menu. 1 The time required to complete this depends on the size of the media the system needs to index. If autoplay is on, you can listen to media processed during indexing.
SYNC™ (If Equipped) When you select: You can: 1. Press OK to select. You can select to play All Artists or any indexed artist. 2. Scroll to choose the desired artist. Press OK. Albums Sort all indexed media by albums. If there are fewer than 255 indexed albums, the system lists them alphabetically in flat file mode. If there are more than 255, the system categorizes them alphabetically. 1. Press OK to enter the album menu and select from playing all albums or from any individual indexed album. 2.
SYNC™ (If Equipped) When you select: You can: Press OK to select. The system creates a new list of similar songs and begins playing. This feature does not include tracks with incomplete metadata information. Return Exit the current menu. * With certain playing devices, if your metadata tags are not populated, the tracks are not available in voice recognition, play menu or similar music.
SYNC™ (If Equipped) When you select: You can: Press OK to select. Return * Exit the current menu. This is a speed-dependent feature. ** Setting Bluetooth to off disconnects all Bluetooth devices and turns off all Bluetooth features. 1. Press AUX and then MENU to enter the media menu. 2. Scroll to System Settings. Press OK. 3. Scroll to Advanced. Press OK. Advanced Menu Options The Advanced menu allows you to access and set prompts, languages, defaults and perform a master reset.
SYNC™ (If Equipped) Use the website at any time to check your phone's compatibility, register your account and set preferences as well as access a customer representative via an online chat (during certain hours). Visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca for more information. SYNC™ TROUBLESHOOTING Your SYNC system is easy to use. However, should questions arise, see the tables below.
SYNC™ (If Equipped) Phone issues Issue Possible cause(s) Possible solution(s) Depending upon your phone, you may have to grant SYNC permission to access your phonebook contacts. Make sure to confirm when prompted by your phone during the phonebook download. I am having trouble connecting my phone to SYNC. This is a phone-dependent feature. This may be a possible phone malfunction. Go to the website to review your phone's compatibility.
SYNC™ (If Equipped) USB and media issues Issue I am having trouble connecting my device. Possible cause(s) This may be a possible device malfunction. SYNC does not recognize This is a device limitation. my device when I turn on the car. Possible solution(s) Try turning off the device, resetting the device, removing the device's battery, then trying again. Make sure you are using the manufacturer's cable. Make sure you insert the USB cable correctly into the device and the USB port.
SYNC™ (If Equipped) Vehicle Health Report and Services (Traffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) I received a text that I did not activate Vehicle Health Report. You did not activate your account on the website. You may have the wrong VIN (vehicle identification number) listed. This is a free feature, but you must first register online to use it. Make sure that your VIN is correctly listed in your account.
SYNC™ (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) SYNC does not understand You may be using the wrong voice commands. what I am saying. You may be speaking too soon or at the wrong time. Review the phone voice commands and the media voice commands at the beginning of their respective sections. After pressing the voice icon, wait until after the tone sounds and Listening appears before saying a command. Any command spoken before this does not register with the system.
SYNC™ (If Equipped) Voice command issues Issue Possible cause(s) Possible solution(s) The system may not be reading the name the same way you are saying it. Contacts in your phonebook may be very short and similar, or they may contain special characters. Your phonebook contacts may be in CAPS. Make sure you are saying the contacts exactly as they are listed. For example, if you save a contact as Joe Wilson, say "Call Joe Wilson".
MyFord Touch™ (If Equipped) GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
MyFord Touch™ (If Equipped) This system uses a four-corner strategy to provide quick access to several vehicle features and settings. The touchscreen provides easy interaction with your cellular phone, multimedia, climate control and navigation system. The corners display any active modes within those menus, such as phone status or the climate temperature.
MyFord Touch™ (If Equipped) • • Calendar Apps Depending on your vehicle and option package, you may also have these controls on your bezel: • Power: Switch the media or climate features off and on. • VOL: Control the volume of playing media. • Seek and Tune: Use as you normally would in media modes. • Eject: Eject a CD from the entertainment system. • SOURCE: Touch the word repeatedly to see all available media modes. The screen does not change, but you see the media change in the lower left status bar.
MyFord Touch™ (If Equipped) • • Safety Information SEEK and PHONE ACCEPT: • While in radio mode, press to seek between memory presets or press and hold to seek between stations. • While in USB or CD mode, press to seek between stations or press and hold to fast seek. • While in phone mode, press to answer a call, or to switch between calls. SEEK and PHONE REJECT: • While in radio mode, press to seek between memory presets or press and hold to seek between stations.
MyFord Touch™ (If Equipped) Speed-restricted Features • Some features of this system may be too difficult to use while your vehicle is moving so they are restricted from use unless your vehicle is stationary. • Screens crowded with information, such as Point of Interest reviews and ratings, SIRIUS Travel Link sports scores, movie times or ski conditions. • Any action that requires you to use a keyboard is restricted, such as entering a navigation destination or editing information.
MyFord Touch™ (If Equipped) Privacy Information Using Voice Recognition When you connect a cellular phone to SYNC, the system creates a profile within your vehicle that links to that cellular phone. This profile helps in offering you more cellular features and operating more efficiently. Among other things, this profile may contain data about your cellular phone book, text messages (read and unread), and call history, including history of calls when your cell phone was not connected to the system.
MyFord Touch™ (If Equipped) What Can I Say? Available voice commands To access the available voice commands for the current session, do one of the following: • During a voice session, press the Help icon (?) in the lower left status bar of the screen. • Say, "What can I say?" for an on-screen listing of the possible voice commands associated with your current voice session. • Press the voice icon. After the tone, say, "Help" to hear a list of possible voice commands.
MyFord Touch™ (If Equipped) • • • 1. Press the voice icon. Wait for the prompt "Please say a command". Another tone sounds to let you know the system is listening. 2. Say any of the following commands: Interaction Mode: Novice mode provides detailed interaction and guidance while the advanced mode has less audible interaction and more tone prompts. Confirmation Prompts: The system uses these short questions to confirm your voice request.
MyFord Touch™ (If Equipped) SETTINGS A B C D E F E161968 A Clock B Display C Sound D Vehicle E Settings F Help Under this menu, you can set your clock, access and adjust the display, sound and vehicle settings as well as access settings for specific modes or the help feature. E142607 E142607 1. Press the Settings icon > Clock. 2. Press + and - to adjust the time.
MyFord Touch™ (If Equipped) The system automatically saves any updates you make to the settings. Uploading Photos for Your Home Screen Wallpaper Display Note: You cannot load photos directly from your camera. You must access the photos either from your USB mass storage device or from an SD card. You can adjust the touchscreen display through the touchscreen or by pressing the voice button on your steering wheel controls and when prompted, say, "Display settings".
MyFord Touch™ (If Equipped) • • • Sound * Occupancy Mode You can find more information on the rear view camera in another chapter. See Rear View Camera (page 157). Speed Compensated Volume * Your vehicle may not have these sound settings. Enable Valet Mode Vehicle E142607 • • • Valet mode allows you to lock the system. No information is accessible until the system is unlocked with the correct PIN. You can create your own four-digit PIN to lock and unlock the system.
MyFord Touch™ (If Equipped) System Language Select to have the touchscreen display in English, Spanish or French. Distance Select to display units in kilometers or miles. Temperature Select to display units in Celsius or Fahrenheit. System Prompt Volume Adjust the volume of voice prompts from the system. Touch Screen Button Beep Select to have the system beep to confirm choices made through the touchscreen.
MyFord Touch™ (If Equipped) Voice control Phone Candidate Lists Candidate lists are possible results from your voice commands. The system simply makes a best guess at your request with these turned off. Voice Control Volume This allows you to adjust the system’s voice volume level.
MyFord Touch™ (If Equipped) Navigation Map Preferences Turn breadcrumbs on and off. Have the system display your turn list top to bottom or bottom to top. Turn the Parking POI notification on and off. Route Preferences Choose to have the system display the Shortest, Fastest or most Ecological route first. If you set Always Use Preferred Route to Yes, the system uses the selected route type to calculate only one route to the desired destination.
MyFord Touch™ (If Equipped) Navigation Have the system display where there may be reduced visibility. Have the system turn on your radio for traffic announcements. Avoid Areas Enter specific areas that you would like to avoid on planned navigation routes. Phone E142607 Press the Settings icon > Settings > Phone, then select from the following: Phone Bluetooth Devices Connect, disconnect, add or delete a device, as well as save it as a favorite. Bluetooth Turn Bluetooth on and off.
MyFord Touch™ (If Equipped) Wireless & Internet feature, everyone in your vehicle can also gain access the internet if you have a USB mobile broadband connection inside your vehicle, your phone supports personal area networking and if you park outside a wireless hotspot. Your system has a Wi-Fi feature that creates a wireless network within your vehicle, thereby allowing other devices (such as personal computers or phones) in your vehicle to speak to each other, share files or play games.
MyFord Touch™ (If Equipped) Wi-fi USB Mobile Broadband Instead of using Wi-Fi, your system can also use a USB mobile broadband connection to access the internet. (You must turn on your mobile broadband device on your personal computer before connecting it to the system.) This screen allows you to set up what is your typical area for your USB mobile broadband connection. (USB mobile broadband settings may not display if the device is already on.
MyFord Touch™ (If Equipped) Help Sirius satellite radio ESN Gracenote Database Information and Library version Software Licenses View the licenses for any software and applications installed on your system. Driving Restrictions Certain features are not accessible when your vehicle is moving. 911 Assist Turn on and turn off the 911 Assist feature. See Information (page 365).
MyFord Touch™ (If Equipped) ENTERTAINMENT A B G C D E H F E161892 A AM 1 and AM AST B FM 1, FM 2 and FM AST C SIRIUS D CD E USB F Touch this button to scroll down for more options, such as SD Card, BT Stereo and A/V In G These buttons change with the media mode you are in. H Radio memory presets and CD controls. Note: Some features may not be available in your area. Contact an authorized dealer for more information.
MyFord Touch™ (If Equipped) Your voice system allows you to change audio sources with a simple voice command. For example, if you are listening to music on a USB device, then want to switch to a satellite radio channel, simply press the voice button on the steering wheel controls and say the name of the SIRIUS station (such as, "the Highway").
MyFord Touch™ (If Equipped) Options Sample commands Sound Settings "Sirius <0-223>"* Touch this button to adjust settings for: "Sports games"* • • • • • • • * This command is only usable if you have an active subscription to SIRIUS satellite radio. ** The commands that have [ ] around the word means that the word is optional. For example, if you say, "Play Metallica", this is the same as the voice command, "Play [artist] ". Note: Your vehicle may not have all these sound settings.
MyFord Touch™ (If Equipped) The multicast indicator appears in FM mode (only) if the current station is broadcasting multiple digital broadcasts. The highlighted numbers signify available digital channels where new or different content is available. HD1 signifies the main programming status and is available in analog and digital broadcasts. Other multicast stations (HD2 through HD7) are only available digitally. Direct Tune Touch this button to manually enter the desired station number.
MyFord Touch™ (If Equipped) When HD Radio broadcasts are active, you can access the following functions: • Scan allows you to hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels. You may see the HD logo appear if the station has a digital broadcast. • Memory presets allow you to save an active channel as a memory preset. Touch and hold a memory preset slot until the sound returns.
MyFord Touch™ (If Equipped) Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required. This is a by the radio broadcaster. broadcast issue. Sound fading or blending in The radio is shifting between No action required. The and out. analog and digital audio. reception issue may clear up as you continue to drive.
MyFord Touch™ (If Equipped) "RADIO" "RADIO" "Tune" "<87.9-107.9>" 3 "Help" 1 "<87.9-107.9> HD" 1 "<530-1710>" If available. 2 If you have said "Browse", see the "Browse" chart later in this section. "AM" 3 If you have said "Tune", see the following "Tune" chart. "AM <530-1710>" "AM autoset" "AM autoset preset <#>" "TUNE" "AM preset <#>" "<530-1710>" "Browse" "<87.9-107.9>" 2 "FM" "<87.9-107.9> HD <#>" "FM <87.9-107.9>" "AM" * "FM <87.9-107.
MyFord Touch™ (If Equipped) Scan "TUNE" "HD <#>" Touch this button to hear a brief sampling of channels. * "Preset <#>" Options "Help" * Touch this button to view and adjust various media settings. If available. Sound Settings SIRIUS® Satellite Radio (If Activated) E142611 Touch this button to adjust settings for: • • • • • • • Press the lower left corner of the touchscreen, and then select the SIRIUS tab. Memory Presets Save a channel by pressing and holding one of the memory preset areas.
MyFord Touch™ (If Equipped) Tune to the channel, to Cancel the alert or to Disable Alerts. If you are listening to a sporting event, you can save your favorite teams so that the system can alert you when they are playing on a satellite radio channel. E142593 Note: SIRIUS does not support the Alert feature on all channels. Ford Motor Company shall not be responsible for Alert feature variation.
MyFord Touch™ (If Equipped) SIRIUS Satellite Radio Reception Factors and Troubleshooting Potential reception issues Antenna obstructions For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other materials as far away from the antenna as possible. Terrain Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception.
MyFord Touch™ (If Equipped) Troubleshooting tips Radio display Cause Action Updating. Update of channel programming in progress. No action required. The process may take up to three minutes. Call SIRIUS 1-888-539-7474. Your satellite service is no longer available. Contact SIRIUS at 1-888539-7474 to resolve subscription issues. None found. Check Channel All the channels in the Use the channel guide to Guide. selected category are either turn off the Lock or Skip skipped or locked.
MyFord Touch™ (If Equipped) Shuffle "SPORTS GAME" Touch this button to play the tracks or entire albums in random order, or turn the feature off if already on. "Tune to the game" "Tune to the game" Scan "Tune to the game" Touch this button to hear a brief sampling of all available tracks. "Tune to the game" More Info "Help" Touch this button to see disc information.
MyFord Touch™ (If Equipped) "CD" "Pause" "Play" "Play next track" "Play previous track" "Play track <1-512>" E142619 "Repeat" The SD card slot is located either in the center console or behind a small access door in the instrument panel. To access and play music from your device, press the lower left corner of the touchscreen. * "Repeat folder" "Repeat off" "Repeat track" "Shuffle" "Shuffle CD" * * "Shuffle folder" "Shuffle off" E142620 "Help" * SD logo is a trademark of SD-3C, LLC.
MyFord Touch™ (If Equipped) This feature allows you to plug in media playing devices, memory sticks, flash drives or thumb drives, and charge devices if they support this feature. In order to playback video from your iPod or iPhone, you must have a special combination USB/RCA composite video cable (which you can buy from Apple). When you connect the cable to your iPod or iPhone, plug the other end into both the RCA jacks and the USB port.
MyFord Touch™ (If Equipped) Playing Video from Your Device "USB" or "SD CARD" To access and play video from your device, your vehicle's transmission must be in position P with the ignition in accessory mode. See Starting and Stopping the Engine (page 124). "Play podcast " "Play podcast episode " "Play similar music" "Play song " SD Card and USB Voice Commands If you are listening to a USB device or an SD card, press the E142599 voice button on the steering wheel controls.
MyFord Touch™ (If Equipped) "BROWSE" "BROWSE" "TV show " "Album " * "All albums" "Video " "All artists" "Video playlist " "All audiobooks" * This command is only available in USB mode and is device-dependent. "All folders" "All genres" Supported Media Players, Formats and Metadata Information * "All music videos" SYNC is capable of hosting nearly any digital media player, including iPod, Zune™, plays from device players, and most USB drives.
MyFord Touch™ (If Equipped) E142611 To access, press the lower left corner on the touchscreen, then select the BT Stereo tab. Bluetooth Audio Voice Commands If you are listening to a Bluetooth audio device, press the voice button on the steering wheel control. When prompted, say "Next song", "Pause", "Play" or "Previous song". E142599 E142622 If you are not listening to a Bluetooth audio device, press the voice button and, after the tone, say "Next song", "Pause", "Play" or "Previous song".
MyFord Touch™ (If Equipped) 3. Press the lower left corner on the touchscreen. Select either a tuned FM station or a CD (if there is a CD already loaded into the system). 4. Adjust the volume as desired. 5. Turn the portable music player on and adjust the volume to ½ the maximum. 6. Press the lower left corner on the touchscreen. Select the A/V In tab. (You should hear audio from your portable music player although it may be low.) 7.
MyFord Touch™ (If Equipped) A Phone B Quick Dial C Phonebook D History E Messaging F Settings Pairing Your Phone for the First Time Hands-free calling is one of the main features of SYNC. Once you pair your phone, you can access many options using the touchscreen or voice commands. While the system supports a variety of features, many are dependent on your cellular phone’s functionality. WARNING Driving while distracted can result in loss of vehicle control, crash and injury.
MyFord Touch™ (If Equipped) SYNC may prompt you with more phone options. For more information on your phone's capability, see your phone's manual and visit the website. Note: Select SYNC, and a six-digit PIN appears on your device. 3. If prompted to enter a PIN on your device, it does not support Secure Simple Pairing. To pair, enter the PIN displayed on the touchscreen. Skip the next step. 4.
MyFord Touch™ (If Equipped) • • Text Messaging Join two calls. End the call. Note: Downloading and sending text messages using Bluetooth are phone-dependent features. Quick Dial Set up favorite contacts from your phonebook or history folder. Note: Certain features in text messaging are speed-dependent and not available when your vehicle is traveling at speeds over 3 mph (5 km/h). Phonebook Touch this button to access and call any contacts in your previously downloaded phone book.
MyFord Touch™ (If Equipped) • • When a new message arrives, an audible tone sounds and the screen displays a pop-up with the caller name and ID, if supported by your phone. You can press: • View to view the text message. • Listen for SYNC to read the message to you. • Dial to call the contact. • Ignore to exit the screen. Send, which sends the message as it is. Edit Text, which allows you to customize the pre-defined message or create a message on your own.
MyFord Touch™ (If Equipped) Text Message Notification "PHONE" Select a text message notification, if supported by your phone. Choose from possible system alert tones, text-to-speech or silent. "Call on other" "Call voicemail" "Dial" Internet Data Connection "Do not disturb off" If your phone is compatible, use this screen to adjust your internet data connection. Select to make your connection profile with the personal area network or to switch off your connection.
MyFord Touch™ (If Equipped) "PHONE" "MESSAGES" * "Unmute call" "Call" "Help" "Forward text messages" * This command is only available during an active call. "Listen to text message <#>" "Listen to text messages" ** If you say "Messages", see the following "Messages" chart for additional commands.
MyFord Touch™ (If Equipped) Note: The driver is ultimately responsible for the safe operation of the vehicle, and therefore, must evaluate whether it is safe to follow the suggested directions. Any navigation features provided are only an aid. Make your driving decisions based on your observations of local conditions and existing traffic regulations.
MyFord Touch™ (If Equipped) 1. Press the voice button. 2. When prompted, say "Services". This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabled cellular phone. 3. Once you connect to the service, follow the voice prompts to request the desired service, such as "Traffic" or "Directions". You can also say, "What are my choices?" to receive a list of available services from which to choose. 4.
MyFord Touch™ (If Equipped) Disconnecting from SYNC Services 1. button on the steering wheel. 2. Say "Good-bye" from the SYNC Services main menu. Press and hold the hang-up phone SYNC Services Quick Tips Message Action and Description Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information. You can save address points, such as work or home.
MyFord Touch™ (If Equipped) Sirius Travel Link (If Equipped) Traffic On Route and Traffic Nearby Touch these buttons to identify traffic incidents on your route, nearby your vehicle’s current location or near any of your favorite places, if programmed. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
MyFord Touch™ (If Equipped) Voice command Sirius Travel Link NHL Voice command WNBA 5-day weather forecast Help Fuel prices Movie listings Additional Sports-Related Voice Commands Sports headlines * Sports schedules * Sports scores * Voice command Baseball headlines Baseball schedule Traffic Baseball scores Weather College basketball headlines Weather map College basketball schedule Help College basketball scores If you say "Sports headlines", "Sports schedules" or "Sports scores", y
MyFord Touch™ (If Equipped) Note: The system alerts you to any messages by turning the information icon yellow. After you read or delete the messages, the icon returns to white. Voice command NBA headlines NBA schedule Calendar NBA scores If your vehicle is equipped with Navigation, touch the I E142608 (Information) button to access these features. If your vehicle is not equipped with Navigation, touch the corner of the touchscreen with the green tab.
MyFord Touch™ (If Equipped) Note: Before setting this feature on, make sure that you read the 911 Assist Privacy Notice later in this section for important information. If your vehicle is equipped with Navigation, touch the I (Information) button to access these features. If your vehicle is not equipped with Navigation, touch the corner of the touchscreen with the green tab. Then select: Note: If any user turns 911 Assist on or off, that setting applies for all paired phones.
MyFord Touch™ (If Equipped) • • • A connected Bluetooth-enabled phone must have the ability to make and maintain an outgoing call at the time of the incident. A connected Bluetooth-enabled phone must have adequate network coverage, battery power and signal strength. The vehicle must have battery power and be located in the United States, Canada or in a territory in which 911 is the emergency number. 911 Assist May Not Work If: • • • Your cellular phone or 911 Assist hardware sustains damage in a crash.
MyFord Touch™ (If Equipped) Note: Your Vehicle Health Report feature requires activation prior to use. Visit www.SYNCMyRide.com to register. There is no fee or subscription associated with Vehicle Health Report, but you must register to use this feature. If you want to run a report by using the touchscreen, select: Message Apps Note: This feature may not function properly if you have enabled caller ID blocking on your cellular phone.
MyFord Touch™ (If Equipped) E146988 A Power: Touch to switch the system off and on. Outside air cannot enter your vehicle when you switch off the system. B Passenger settings: Touch + or – to adjust the temperature. C Fan speed: Touch + or - to adjust fan speed. D DUAL: Touch to switch on the passenger temperature control.
MyFord Touch™ (If Equipped) I Manual airflow distribution controls:Footwell and Defrost: Distributes air through the windshield defroster vents, demister vents, floor vents and rear seat floor vents, and provides outside air to reduce window fogging. Panel: Distributes air through the instrument panel vents. Panel and Floor: Distributes air through the instrument panel vents, demister vents, floor vents and rear seat floor vents.
MyFord Touch™ (If Equipped) "CLIMATE" * "A/C off" "Off" "A/C on" "On" "Automatic" "Panel floor on" "Defrost off" "Panel on" "Defrost on" "Panel off" "Dual off" "Recirc off" "Floor on" "Recirc on" "Fan decrease" "Temperature" "Fan increase" "Temperature <15.5-29.
MyFord Touch™ (If Equipped) NAVIGATION (If Equipped) Destination Note: The navigation SD card must be in the SD card slot to operate the navigation system. If you need a replacement SD card, see an authorized dealer. City Center Map Edit Route Cancel Route Note: The SD card slot is spring-loaded. To remove the SD card, just push the card in and release it. Do not attempt to pull the card out to remove it; this could cause damage. 1.
MyFord Touch™ (If Equipped) Note: If your vehicle is on a recognized road and you do not press the Start Route button, the system defaults to the Fastest Route option and begins guidance. Subcategories Personal Care Services Auto Dealership During route guidance, you can press the talking bubble icon that appears in the upper right navigation corner (green bar) if you want the system to repeat route guidance information.
MyFord Touch™ (If Equipped) Press More Information for a longer review, a list of services and facilities, the average room or meal price as well as the website. This screen displays the point of interest icon such as: • • Pool Wi-fi. For restaurants, cityseekr can provide information such as star rating, average cost, review, handicap access, hours of operation, and website address.
MyFord Touch™ (If Equipped) Route Preferences Traffic Preferences Preferred Route Avoid Traffic Problems Choose to have the system display the Shortest, Fastest or most Ecological route first. If you set Always Use Preferred Route to Yes, the system uses the selected route type to calculate only one route to the desired destination. Choose how you want the system to handle traffic problems along your route.
MyFord Touch™ (If Equipped) 2D city maps show detailed outlines of buildings, visible land use and land elements and detailed railway infrastructure for the most essential cities around the globe. These maps also contain features, such as town blocks, building footprints, and railways. 3D map mode provides an elevated perspective of the map.
MyFord Touch™ (If Equipped) Scroll cursor allows you to scroll the map; the fixed icon is in the center of the screen. The map E142647 position closest to the cursor is in a window on the top center part of the screen. No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map E142655 positioning. This icon may display under normal operation in an area with poor GPS access. Address book entry default icon(s) indicates the location on the map of an address book entry.
MyFord Touch™ (If Equipped) • • • • • Edit Turn List Detour Edit Route Preferences Edit Traffic Preferences Cancel Route. Navigation system voice commands "Destination intersection" "Destination nearest " "Destination nearest POI" Nokia is the digital map provider for the navigation application. If you find map data errors, you may report them directly to Nokia by going to http://mapreporter.navteq.com.
MyFord Touch™ (If Equipped) Navigation system voice commands "NAVIGATION" "Zoom out" "Zoom maximum" "Help" "Zoom province" These commands are only available when a navigation route is active. "Zoom state" 1 "Zoom street" 2 If you say "Destination", you can then say any command in the following "Destination" chart. "Zoom to " "Help" 3 If you say "Navigation", you can then say any command in the following "Navigation" chart.
Accessories • • For a complete listing of the accessories that are available for your vehicle, please contact an authorized dealer or visit our online store at www.Accessories.Ford.com (United States only). Peace of mind • • • • • Ford Motor Company will repair or replace any properly authorized dealer-installed Ford Genuine Accessories found to be defective in factory-supplied materials or workmanship during the warranty period, as well as any component damaged by the defective accessories.
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label). Ask an authorized dealer for specific weight information.
Appendices • END USER LICENSE AGREEMENT SYNC® End User License Agreement (EULA) • • You have acquired a device ("DEVICE") that includes software licensed by Ford Motor Company and its affiliates ("FORD MOTOR COMPANY") from an affiliate of Microsoft Corporation ("MS") . Those installed software products of MS origin, as well as associated media, printed materials, and "online" or electronic documentation ("MS SOFTWARE") are protected by international intellectual property laws and treaties.
Appendices • Description of Other Rights and Limitations • • • • Speech Recognition: If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process. Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
Appendices • • • supplements, add-on components, or Internet-based services components of the SOFTWARE after the date you obtain your initial copy of the SOFTWARE ("Supplemental Components").
Appendices • • Links to Third Party Sites: The MS SOFTWARE may provide you with the ability to link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation, their affiliates and/or their designated agent.
Appendices Adobe TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, MS, Microsoft Corporation, third party software or service providers, their affiliates or suppliers. Contains Adobe® [Flash® Player] or [AIR®] technology by Adobe Systems Incorporated. This [Licensee Product] contains [Adobe® Flash® Player] [Adobe® AIR®] software under license from Adobe Systems Incorporated, Copyright ©1995-2009 Adobe Macromedia Software LLC.
Appendices Use of Speech Recognition Functions: Speech recognition software is inherently a statistical process which is subject to errors. It is your responsibility to monitor any speech recognition functions included in the system and address any errors. WARNING Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences.
Appendices Potential Map Inaccuracy: Maps used by this system may be inaccurate because of changes in roads, traffic controls or driving conditions. Always use good judgment and common sense when following the suggested routes. Telenav may revise this Agreement and the privacy policy at any time, with or without notice to you. You agree to visit http://www.telenav.com from time to time to review the then current version of this Agreement and of the privacy policy.
Appendices 2.
Appendices COURSE OF DEALING, CUSTOM OR TRADE AND INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS WITH RESPECT TO THE TELENAV SOFTWARE. Certain jurisdictions do not permit the disclaimer of certain warranties, so this limitation may not apply to you.
Appendices the terms and conditions of this Agreement. Any such sale, assignment or transfer that is not expressly permitted under this paragraph will result in immediate termination of this Agreement, without liability to Telenav, in which case you and all other parties shall immediately cease all use of the Telenav Software. Notwithstanding the foregoing, Telenav may assign this Agreement to any other party at any time without notice, provided the assignee remains bound by this Agreement.
Appendices Agreement), and thus your use of the Telenav Software is also subject to such terms. You agree to comply with the following additional terms and conditions, which are applicable to Telenav’s third party vendor licensors: TERMS AND CONDITIONS License Limitations on Use: You agree that your license to use this Data is limited to and conditioned on use for solely personal, noncommercial purposes, and not for service bureau, timesharing or other similar purposes.
Appendices Disclaimer of Liability: real time route guidance, fleet management or similar applications; or (b) with, or in communication with, including without limitation, cellular phones, palmtop and handheld computers, pagers, and personal digital -assistants or PDAs. This Data is provided to you “as is”, and you agree to use it at your own risk.
Appendices Entire Agreement: Government End Users: These terms and conditions constitute the entire agreement between HERE (and its licensors, including their licensors and suppliers) and you pertaining to the subject matter hereof, and supersedes in their entirety any and all written or oral agreements previously existing between us with respect to such subject matter.
Appendices Gracenote® Copyright You agree that you will use the content from Gracenote ("Gracenote Content") , Gracenote Data, the Gracenote Software, and Gracenote Servers for your own personal, non-commercial use only. You agree not to assign, copy, transfer or transmit the Gracenote Content, Gracenote Software or any Gracenote Data (except in a Tag associated with a music file) to any third party.
Appendices THE GRACENOTE SOFTWARE, EACH ITEM OF GRACENOTE DATA AND THE GRACENOTE CONTENT ARE LICENSED TO YOU "AS IS". NEITHER GRACENOTE MAKES ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, REGARDING THE ACCURACY OF ANY GRACENOTE DATA FROM THE GRACENOTE SERVERS OR GRACENOTE CONTENT.
Extended Service Plan (ESP) PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRS WITH A FORD EXTENDED SERVICE PLAN. That means you get: • Reliable, quality service at any Ford or Lincoln dealership • Repairs performed by factory trained technicians, using genuine parts SERVICE PLANS (U.S. Only) More than 32 million Ford owners have discovered the powerful protection of Ford Extended Service Plan.
Extended Service Plan (ESP) SERVICE PLANS (CANADA ONLY) Avoid the Rising Cost of Properly Maintaining Your Vehicle! You can get more protection for your vehicle by purchasing a Ford Extended Service Plan. Ford Extended Service Plan is the only service contract backed by Ford Motor Company of Canada, Limited.
Scheduled Maintenance Genuine Ford and Motorcraft® Replacement Parts GENERAL MAINTENANCE INFORMATION Dealerships stock Ford, Motorcraft and Ford-authorized branded re-manufactured replacement parts. These parts meet or exceed our specifications. Parts installed at your dealership carry a nationwide 24-month or unlimited mile (kilometer) parts and labor limited warranty.
Scheduled Maintenance When the oil change message appears in the information display, it is time for an oil change. Make sure you perform the oil change within two weeks or 500 miles (800 kilometers) of the message appearing. Make sure you reset the Intelligent Oil-Life Monitor after each oil change. See Engine Oil Check (page 212). Additives and Chemicals This owner's manual and the Ford Workshop Manual list the recommended additives and chemicals for your vehicle.
Scheduled Maintenance Check every month Engine oil level. Function of all interior and exterior lights. Tires (including spare) for wear and proper pressure. Windshield washer fluid level. Check every six months Battery connections. Clean if necessary. Body and door drain holes for obstructions. Clean if necessary. Cooling system fluid level and coolant strength. Door weatherstrips for wear. Lubricate if necessary. Hinges, latches and outside locks for proper operation. Lubricate if necessary.
Scheduled Maintenance Multi-Point inspection Accessory drive belt(s) Hazard warning system operation Battery performance Horn operation Engine air filter Radiator, cooler, heater and air conditioning hoses Exhaust system Suspension components for leaks or damage Exterior lamps operation * Fluid levels ; fill if necessary Steering and linkage Tires (including spare) for wear and proper pressure * ** For oil and fluid leaks Windshield for cracks, chips or pits Half-shaft dust boots Washer sp
Scheduled Maintenance When to expect the OIL CHANGE REQUIRED message Interval Vehicle use and example Normal Normal commuting with highway driving No, or moderate, load or towing Flat to moderately hilly roads No extended idling 7500-10000 miles (12000-16000 km) Severe Moderate to heavy load or towing Mountainous or off-road conditions Extended idling Extended hot or cold operation 5000-7499 miles (8000-11999 km) Extreme 3000-4999 miles (4800-7999 km) Maximum load or towing Extreme hot or cold oper
Scheduled Maintenance * At every oil change interval as indicated by the information display Inspect the tires, tire wear and measure the tread depth. Inspect the wheels and related components for abnormal noise, wear, looseness or drag. * Do not exceed one year or 10000 miles (16000 kilometers) between service intervals. ** Reset the Intelligent Oil-Life Monitor after engine oil and filter changes. See Engine Oil Check (page 212).
Scheduled Maintenance Perform the services shown in the following tables when specified or within 3000 miles (4800 kilometers) of the OIL CHANGE REQUIRED message appearing in the information display. • Example 1: The OIL CHANGE REQUIRED message comes on at 28751 miles (46270 kilometers). Perform the 30000-mile (48000-kilometer) automatic transmission fluid replacement.
Scheduled Maintenance Extensive idling or low-speed driving for long distances, as in heavy commercial use (such as delivery, taxi, patrol car or livery) Every 30000 miles (48000 Change automatic transmission fluid. km) Every 60000 miles (96000 Replace spark plugs. km) * This is an optional feature. Operating in dusty or sandy conditions (such as unpaved or dusty roads) Inspect frequently, service as required * Replace cabin air filter. Replace engine air filter.
Scheduled Maintenance California fuel filter replacement: If you register your vehicle in California, the California Air Resources Board has determined that the failure to perform this maintenance item does not nullify the emission warranty or limit recall liability before the completion of your vehicle's useful life. Ford Motor Company, however, urges you to have all recommended maintenance services performed at the specified intervals and to record all vehicle service.
Scheduled Maintenance SCHEDULED MAINTENANCE RECORD Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 414 Escape (TM2) , enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 415 Escape (TM2) , enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 416 Escape (TM2) , enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 417 Escape (TM2) , enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 418 Escape (TM2) , enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 419 Escape (TM2) , enUSA
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 420 Escape (TM2) , enUSA
Index 4 Audible Warnings and Indicators.............87 Automatic Transmission Warning Chime..................................................................88 Engine On Warning Chime................................87 Headlamps On Warning Chime.....................88 Key in Ignition Warning Chime.........................87 Keyless Warning Alert ........................................87 Parking Brake On Warning Chime.................88 4WD See: Four-Wheel Drive.......................................
Index B Checking MyKey System Status................51 Checking the Wiper Blades.......................219 Child Restraint and Safety Belt Maintenance.................................................32 Child Safety.......................................................14 Blind Spot Information System...............161 Blind Spot Information System (BLIS®) with Cross Traffic Alert.................................161 General Information.............................................
Index Digital Radio..................................................282 Engine Oil Dipstick - 1.6L EcoBoost™..................................................212 Engine Oil Dipstick - 2.0L EcoBoost™/ 2.5L..................................................................212 Engine Specifications................................262 HD Radio Reception and Station Troubleshooting............................................283 Entertainment...............................................
Index Floor Mats.......................................................185 Fog Lamps - Front See: Front Fog Lamps.........................................75 Getting Assistance Outside the U.S. and Canada..........................................................194 Getting the Services You Need.................191 Ford Credit..........................................................11 Away From Home................................................191 (U.S. Only)............................................
Index J Information Displays....................................89 General Information...........................................89 Information....................................................365 Jump Starting the Vehicle.........................188 911 Assist.................................................................371 Alerts........................................................................371 Calendar.................................................................
Index N Lug Nuts See: Changing a Road Wheel.......................256 Navigation......................................................378 M Closing the Liftgate.............................................59 Opening the Liftgate...........................................59 cityseekr................................................................379 Map Mode.............................................................381 Navigation Map Updates...............................
Index Phone...............................................................359 Remote Control..............................................43 Making Calls.........................................................361 Pairing Subsequent Phones...........................361 Pairing Your Phone for the First Time..................................................................360 Phone Menu Options........................................361 Phone Settings...................................................
Index Safety Belts......................................................26 Starting a Gasoline Engine........................125 Principle of Operation........................................26 Automatic Engine Shutdown.........................126 Failure to Start.....................................................126 Guarding Against Exhaust Fumes................128 Important Ventilating Information...............128 Stopping the Engine When Your Vehicle is Moving.......................................
Index U Tire Care..........................................................238 Glossary of Tire Terminology.........................239 Information About Uniform Tire Quality Grading.............................................................238 Information Contained on the Tire Sidewall...........................................................240 Temperature A B C............................................239 Traction AA A B C...............................................238 Treadwear................
Index W Using Traction Control...............................148 Switching the System Off Using a Switch................................................................148 Switching the System Off Using the Information Display Controls....................148 System Indicator Lights and Messages..........................................................148 Warning Lamps and Indicators................85 Airbag - Front.........................................................85 Anti-Lock Braking System.......
