2014 MUSTANG Owner’s Manual ER3J 19A321 AA | December 2012 2014 MUSTANG Owner’s Manual fordowner.com ford.ca | First Printing | Owner’s Manual | Mustang | Litho in U.S.A.
Table of Contents 1 Introduction 9 Child Safety Child seat positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Booster seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing child seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 .19 .21 .24 Safety Belts Fastening the safety belts . . . . . . . . . . . . . . . Safety belt warning light and indicator chime . Safety belt-minder . . . . . . . . . . . . . .
2 Table of Contents Locks 65 Locking and unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Interior luggage compartment release . . . . . . . . . . . . . . . . . . . . . . .69 Security 70 SecuriLock® passive anti-theft system. . . . . . . . . . . . . . . . . . . . . . .70 Anti-theft system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Steering Wheel 75 Adjusting the steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 3 Instrument Cluster 92 Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Warning lamps and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Audible warnings and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Information Displays 99 Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Information messages . . . . . . . . . . . . . . . . . . . . . . . .
4 Table of Contents Storage Compartments 153 Center console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153 Starting and Stopping the Engine 154 Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 Engine block heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 Fuel and Refueling Fuel quality . . . . . . Running out of fuel. Refueling . . . . . . . . Fuel consumption . . . . . . 159 .160 .161 .163 .
Table of Contents 5 Cruise Control 190 Driving Aids 192 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 Load Carrying 194 Vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 Towing 201 Trailer towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 Wrecker towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205 Recreational towing . . . . . . . .
6 Table of Contents Maintenance General information . . . . . . . . . . . Opening and closing the hood . . . . Under hood overview . . . . . . . . . . Engine compartment. . . . . . . . . . . Engine oil dipstick . . . . . . . . . . . . Engine oil check . . . . . . . . . . . . . . Engine coolant check . . . . . . . . . . Automatic transmission fluid check Brake fluid check . . . . . . . . . . . . . Power steering fluid check . . . . . . Washer fluid check . . . . . . . . . . . . Battery . . . . . . . . . .
Table of Contents 7 Wheels and Tires Tire care . . . . . . . . . . . . . . . . . . . . . . . . Tire Pressure Monitoring System (TPMS) Changing a road wheel . . . . . . . . . . . . . . Temporary mobility kit . . . . . . . . . . . . . . Technical specifications. . . . . . . . . . . . . . Wheel lug nut torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Table of Contents Navigation System (If Equipped) Status bars. . . . . . . . . . . . . . . . . . . . . . . Loading pictures. . . . . . . . . . . . . . . . . . . Voice recognition . . . . . . . . . . . . . . . . . . Accessing media features . . . . . . . . . . . . Jukebox features . . . . . . . . . . . . . . . . . . Recording (saving) music to your jukebox Accessing the music in your jukebox . . . . Creating a playlist. . . . . . . . . . . . . . . . . . Where am I?. . . . . . . . . . . . . . . . . . . .
Introduction 9 ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it. WARNING: Always drive with due care and attention when using and operating the controls and features on your vehicle. Note: This manual describes a range of product features and options, sometimes before they are generally available.
10 Introduction SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle.
Introduction Symbol Description Fuel pump reset Heated rear window Lighting control Panic alarm Power steering fluid Service engine soon Windshield defrost and demist 11 Symbol Description Symbol Description Fuse Hazard compartment warning flasher Interior Jack luggage compartment release Low tire Maintain pressure correct fluid warning level Parking aid Parking brake system system Power windows front and rear Side airbag Power window lockout Stability control Windshield washer and wiper DATA RECORDI
12 Introduction For U.S. only (if equipped), if you choose to use the SYNC® Vehicle Health Report, you consent that certain diagnostic information may also be accessed electronically by Ford Motor Company and Ford authorized service facilities, and that the diagnostic information may be used for any purpose. See the SYNC® chapter for more information. Event Data Recording This vehicle is equipped with an event data recorder (EDR).
Introduction 13 To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the EDR.
14 Introduction CALIFORNIA PROPOSITION 65 WARNING: Some constituents of engine exhaust, certain vehicle components, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. PERCHLORATE MATERIAL Note: Certain components in your vehicle, such as airbag modules, safety belt pretensioners, and remote control batteries, may contain perchlorate material.
Introduction 15 Collision Repairs We hope that you never experience a collision, but accidents do happen. Genuine Ford replacement collision parts meet our stringent requirements for fit, finish, structural integrity, corrosion protection and dent resistance. During vehicle development, we validate that these parts deliver the intended level of protection as a whole system. A great way to know for sure you are getting this level of protection is to use genuine Ford replacement collision parts.
16 Introduction MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs. However, you must not compromise your own or others’ safety when using such equipment. Mobile communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.
Child Safety 17 GENERAL INFORMATION See the following sections for directions on how to properly use safety restraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your vehicle. Failure to follow these instructions and guidelines may result in an increased risk of serious injury or death to your child. WARNING: All children are shaped differently.
18 Child Safety Recommendations for Safety Restraints for Children Recommended Child size, height, weight, or age restraint type Small Children who have outgrown or no longer Use a children properly fit in a child safety seat belt-positioning (generally children who are less than booster seat. 4 ft. 9 in. (1.45 m) tall, are greater than age four (4) and less than age twelve (12), and between 40 lb (18 kg) and 80 lb (36 kg) and upward to 100 lb (45 kg) if recommended by your child restraint manufacturer).
Child Safety 19 CHILD SEAT POSITIONING WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat upon which the child seat is installed all the way back. When possible, all children age 12 and under should be properly restrained in a rear seating position.
20 Child Safety WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash. WARNING: To avoid risk of injury, do not leave children, unreliable adults, or pets unattended in your vehicle.
Child Safety 21 BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash. Use a belt-positioning booster seat for children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.
22 Child Safety Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat. In this case, move the backless booster to another seating position with a higher seat back or head restraint and lap and shoulder belts, or consider using a high back booster seat.
Child Safety 23 Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The following drawings compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
24 Child Safety INSTALLING CHILD SEATS Child Seats Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). Using Lap and Shoulder Belts WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Child Safety 25 • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place the vehicle seat upon which the child seat will be installed in the upright position. • Put the safety belt in the automatic locking mode. See Step 5. This vehicle does not require the use of a locking clip.
26 Child Safety 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Child Safety 27 8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle.
28 Child Safety Using Lower Anchors and Tethers for CHildren (LATCH) WARNING: Never attach two child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. WARNING: Depending on where you secure a child restraint, and depending on the child restraint design, you may block access to certain safety belt buckle assemblies or LATCH lower anchors, rendering those features potentially unusable.
Child Safety 29 Your vehicle has LATCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LATCH anchors are located at the rear section of the rear seat between the cushion and seat back below the symbols as shown. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Follow the instructions on attaching child safety seats with tether straps. See Using Tether Straps later in this chapter.
30 Child Safety The tether strap anchors in your vehicle are in the following positions (shown from top view): Perform the following steps to attach a child safety seat to the tether anchor: For coupe: 1. Route the tether strap over the top of the head restraint. 2. Locate the correct anchor for the selected seating position. 3. Open the tether anchor cover. 4. Clip the tether strap to the anchor as shown.
Child Safety 31 For convertible: 1. Route the child safety seat tether strap over the top of the head restraint. The tether anchors are located rearward of the seat back in the convertible top sling. Note: For easier access, attach the tether with the convertible top up. Note: The attachments for the convertible boot located on the back of the head restraints are not tether anchors.
32 Child Safety 2. Access tether anchors located behind the seat back under the vinyl tag marked with the child tether anchor symbol. 3. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 4. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Safety Belts 33 PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a crash.
34 Safety Belts WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
Safety Belts 35 The safety belt pretensioners are designed to activate in frontal, near-frontal and side crashes. The safety belt pretensioners at the front seating positions are designed to tighten the safety belts firmly against the occupant’s body when activated. This helps increase the effectiveness of the safety belts. In frontal crashes, the safety belt pretensioners can be activated alone or, if the crash is of sufficient severity, together with the front airbags.
36 Safety Belts 2. To unfasten, press the release button and remove the tongue from the buckle. Restraint of Pregnant Women WARNING: Always ride and drive with your seat back upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest. Pregnant women should also follow this practice. See the following figure.
Safety Belts 37 WARNING: The belt and retractor assembly must be replaced if the safety belt assembly automatic locking retractor feature or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in crashes. All safety restraints in the vehicle are combination lap and shoulder belts.
38 Safety Belts How to Use the Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Safety Belts 39 SAFETY BELT WARNING LIGHT AND INDICATOR CHIME This lamp illuminates and an audible warning will sound if the driver’s safety belt has not been fastened when the vehicle’s ignition is turned on. Conditions of Operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the on position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
40 Safety Belts If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 6 mph (9.7 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to on...
Safety Belts 41 Note: The driver and front passenger Belt-Minder® are deactivated and activated independently. When deactivating or activating one seating position, do not buckle the other position as this will terminate the process. Note: If you are using MyKey®, the Belt-Minder® cannot be disabled. Also, if the Belt-Minder® has been previously disabled, it will be re-enabled during the use of MyKey®. See the MyKey® chapter. Read Steps 1 - 4 thoroughly before proceeding with the programming procedure.
42 Safety Belts CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts. Replace if necessary.
Personal Safety System 43 PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
44 Supplementary Restraints System PRINCIPLES OF OPERATION WARNING: Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. WARNING: All occupants of your vehicle, including the driver, should always properly wear their safety belts, even when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.
Supplementary Restraints System 45 WARNING: If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash. The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag.
46 Supplementary Restraints System SOS POST-CRASH ALERT SYSTEM™ The system flashes the turn signal lamps and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag equipped on your vehicle, such as front, side, side curtain or Safety Canopy®. The horn and lamps will turn off when: • the hazard control button is pressed • the panic button (if equipped) is pressed on the remote entry transmitter, or • your vehicle runs out of power.
Supplementary Restraints System 47 The driver and passenger front airbag system consists of: • driver and passenger airbag modules • crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator later in this chapter.
48 Supplementary Restraints System Children and Airbags WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Supplementary Restraints System 49 WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console. Check the passenger airbag off or pass airbag off indicator lamp for proper airbag status. Failure to follow these instructions may interfere with the passenger seat sensing system.
50 Supplementary Restraints System • If the child restraint has been installed and the indicator lamp is not lit, then turn your vehicle off, remove the child restraint from your vehicle and reinstall the restraint following the child restraint manufacturer’s instructions. The front passenger sensing system is designed to enable (may inflate) the front passenger’s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.
Supplementary Restraints System 51 If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • objects lodged underneath the seat • objects between the seat cushion and the center console (if equipped) • objects hanging off the seat back • objects stowed in the seat back map pocket (if equipped) • objects placed on the occupant’s lap • cargo interference with the seat • other passengers pushing or pulling on the seat • rear passenger feet and knees rest
52 Supplementary Restraints System If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this owner’s manual. SIDE AIRBAGS WARNING: Do not place objects or mount equipment on or near the airbag cover, on the side of the seat backs (of the front seats), or in front seat areas that may come into contact with a deploying airbag.
Supplementary Restraints System 53 The system consists of the following: • a tag on the seat back indicating that side airbags are found on your vehicle • side airbags located inside the seat back of the driver and front passenger seats. • crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator later in this chapter. • front passenger sensing system.
54 Supplementary Restraints System The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. The readiness of the safety system is indicated by a warning indicator light in the instrument cluster or by a backup tone if the warning light is not working. See the Instrument Cluster chapter. Routine maintenance of the airbag is not required.
Keys and Remote Control 55 GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
56 Keys and Remote Control Note: If the vehicle is not equipped with active anti-theft system, locking the driver door with the key does not lock the passenger door. Use the power door lock, remote control or manually lock the passenger door to ensure the vehicle is properly secured. Note: Your vehicle’s keys were issued with a security label that provides important vehicle key cut information. Keep the label in a safe place for future reference. Car Finder Press the button twice within three seconds.
Keys and Remote Control 57 Integrated Keyhead Transmitter 1. Twist a thin coin in the slot near the key 1 ring to remove the battery cover (1). 2. Carefully peel up the rubber gasket (2) 2 from the transmitter if it does not come off with the battery cover. 3 3. Remove the old battery (3). 4. Insert the new battery. Refer to the instructions inside the integrated keyhead transmitter for the correct orientation of the battery.
58 MyKey PRINCIPLES OF OPERATION MyKey® allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as an administrator key or admin key which can be used to: • create a restricted key • program optional MyKey settings • clear all MyKey features altogether.
MyKey 59 Optional Settings These settings can be configured right after a MyKey is first created or changed afterward with an admin key. • Vehicle speed limit of 80 mph (130 km/h). Visual warnings are displayed followed by an audible tone when vehicle speed has reached 80 mph (130 km/h). • Vehicle speed warning of 45, 55 or 65 mph (75, 90, or 105 km/h). Visual warnings are displayed followed by an audible tone when the preselected vehicle speed is exceeded. • Audio system maximum volume of 45%.
60 MyKey 4. Press OK to select CREATE MYKEY. 5. Hold OK as prompted until you see MARK THIS KEY AS RESTRICTED. The key is successfully programmed. Make sure you label it so you can distinguish it from the admin keys. To program optional settings for the key(s), see the Programming/Changing Optional Settings chapter. Programming/Changing Optional Settings Note: All programmed keys can be cleared within the same key cycle in which a key was programmed, otherwise an admin key is required to clear the keys.
MyKey 61 CLEARING ALL MYKEYS Note: All programmed MyKeys can be cleared within the same key cycle in which a MyKey was created, otherwise an admin key is required to clear the keys. To clear all MyKeys (which removes all restrictions and returns them to admin key status), use the information display controls to do the following: For Type 1 information display settings 1. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 2. Press and release the RESET button.
62 MyKey Vehicles Equipped with Traditional Keys When using a non-Ford-approved remote start system, the default settings may recognize the remote start system as an additional admin key with its associated privileges. It is NOT compatible with MyKey. Restart the engine when you insert a key into the ignition cylinder; it may help you to retain some MyKey functions.
MyKey 63 MYKEY TROUBLESHOOTING Condition I cannot program a key. I cannot program the optional settings. I cannot clear the restricted keys. I lost the only admin key. I lost a key. Potential Causes • The key in the ignition does not have admin privileges. • The key in the ignition is the only admin key (there always has to be at least one admin key). • The intelligent access key is not in the backup slot (vehicles with push button start).
64 Condition I accidentally programmed all keys as restricted keys. No restricted key functions with intelligent access key (push button start). Restricted key programmed total includes one additional key. MyKey Potential Causes • The vehicle has a remote start system that is recognized as an admin key. See the Using MyKey with Remote Start System chapter to reset all restricted keys using remote start. • An admin key is present at engine start-up. • No restricted keys are programmed to the vehicle.
Locks 65 LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lock and unlock the vehicle. Power Door Locks The power door lock control is located on the driver and front passenger door panels. A. Unlock B. Lock A B Remote Control You can use the remote control anytime the vehicle is not running. Unlocking the Doors (Two-Stage Unlock) Press the button to unlock the driver’s door. Press the button again within three seconds to unlock all doors.
66 Locks Opening the Trunk Press the button twice within three seconds to open the trunk. Make sure the trunk is closed and latched before driving your vehicle. An unlatched trunk may cause objects to fall out or block the driver’s rear view. Smart Locks This feature helps prevent you from locking yourself out of your vehicle if your key is still in the ignition.
Locks 67 Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Enabling or Disabling Autolock and Autounlock Note: The autolock and autounlock features can be activated or deactivated independently of each other: • through your authorized dealer • by using the information display.
68 Locks TRUNK RELEASE The remote trunk release button is located on the center console. Press the button to unlatch the trunk. Interior Trunk Control Lockout (Convertible Vehicles Only) This feature disables the interior trunk control. It helps prevent unauthorized access to the trunk when the convertible top is open. To disable the interior trunk control: 1. Make sure the vehicle is off and accessory power delay is not active. 2. Lock the vehicle using the remote control or the power door lock switch.
Locks 69 INTERIOR LUGGAGE COMPARTMENT RELEASE WARNING: Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles. WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.
70 Security SECURILOCK® PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting issues if they are too close to the key when starting the engine. Prevent these objects from touching the coded key while starting the engine.
Security 71 Replacement Keys Note: Your vehicle comes with two integrated keyhead transmitters. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control. A maximum of eight coded keys can be programmed to your vehicle; only four of these eight keys can be integrated keyhead transmitters with remote entry functionality.
72 Security 7. After three seconds but within 20 seconds of turning the ignition off and removing the previously programmed coded key, insert the new unprogrammed key into the ignition. 8. Turn the ignition from off to on. Keep the ignition on for at least six seconds. 9. Remove the newly programmed coded key from the ignition. The key will start the vehicle’s engine and will operate the remote entry system (if the new key is an integrated keyhead transmitter) if it has been successfully programmed.
Security 73 Full Monitor Mode To monitor the following: • Doors • Hood • Trunk • Movement inside the vehicle (for convertible models, top must be fully closed) • Change in vehicle inclination (such as unwanted towing) Lock the vehicle using the remote control or the power door lock control with the accompanying door open and then close all doors. Note: Do not choose full monitor mode if movement within the vehicle is likely to occur or when the vehicle is in transport.
74 Security Each door, the hood or the trunk is armed individually, and if any are open, they must be closed for the system to enter the 20 second countdown. The turn signal lamps will flash once when all doors, the hood and the trunk are closed indicating the vehicle is locked and entering the 20 second countdown. If any closure is not properly closed, the turn signal lamps will not flash and that closure will not be armed.
Steering Wheel 75 ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position in the Seats chapter. 1. Unlock the steering column. 2 2. Adjust the steering wheel to the desired position. 1 3. Lock the steering column. AUDIO CONTROL (IF EQUIPPED) A B C - + E A. Media B. Volume down C. Volume up D. Seek up or next E.
76 Steering Wheel Press the media button repeatedly to scroll through available audio modes. Press the seek buttons to select the next or previous stored preset or track. Press and hold to select the next or previous frequency or seek through a track. VOICE CONTROL (IF EQUIPPED) A - B + A. Voice recognition B. Phone mode OK See the SYNC or Navigation System chapter. CRUISE CONTROL See the Cruise Control chapter.
Steering Wheel INFORMATION DISPLAY CONTROL Type 1 Type 2 OK See the Information Displays chapter.
78 Wipers and Washers WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.
Wipers and Washers 79 WINDSHIELD WASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out. Always use the windshield washer before wiping a dry windshield. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Press the end of the stalk to activate the washer. OFF • A brief press causes a single wipe without washer fluid.
80 Lighting LIGHTING CONTROL A B C A. Off B. Parking lamps, instrument panel lamps, license plate lamps and tail lamps C. Headlamps A High Beams • Push the lever toward the instrument panel to activate. • Pull the lever toward you to deactivate. OFF Headlamp Flasher •Pull toward you slightly to activate and release to deactivate.
Lighting 81 AUTOLAMPS (If equipped) WARNING: In severe weather conditions, it may be necessary to switch your headlamps on manually. Note: If the vehicle is equipped with autolamps, it will have the windshield wiper rainlamp feature. When the windshield wipers are turned to low- or high-speed wiping during daylight, and the headlamp control is in the autolamp position, the exterior lamps will turn on after a brief delay and will remain on until the wipers are turned off.
82 Lighting Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer switch requires re-calibration. Rotate the dimmer switch from the full dim position to the full dome On position to reset. This will ensure that your displays are visible under all lighting conditions. HEADLAMP EXIT DELAY You can set the delay time to keep the headlamps on for up to three minutes after the ignition is turned off.
Lighting 83 DAYTIME RUNNING LAMPS (IF EQUIPPED) WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
84 Lighting DIRECTION INDICATORS • Push down to activate the left turn signal. • Push up to activate the right turn signal. OFF Note: An outage of any front turn signal lamp or the inner most of the three-compartment rear turn signal lamps will result in a rapid flash rate. INTERIOR LAMPS Dome/Map lamps The dome lamp lights when: • Any door is opened. • Any of the remote entry controls are pressed and the ignition is off.
Windows and Mirrors 85 POWER WINDOWS WARNING: Do not leave children unattended in your vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings. AUTO AUTO Press or lift the switches to operate the windows. • Press the switch to the first detent and hold to open the window.
86 Windows and Mirrors Bounce-Back The window will stop automatically while closing and reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature WARNING: When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care when closing the windows to avoid personal injury. Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection.
Windows and Mirrors 87 Manual Override The rear quarter window switch will not operate when: • the convertible top is moving • the convertible top is not completely up or down. The rear quarter windows can be manually raised if the switch does not operate when the convertible top is completely up or down. The following procedure must be performed within two minutes: 1. Switch the ignition off, then back on. 2. Press the rear window switch down three times. 3. Switch the ignition off, then back on. 4.
88 Windows and Mirrors Pony Projection Lights (If Equipped) Note: Moisture, frost and ice build-up (or other types of contamination) on the surface of the light lens can cause some non-permanent distortion or reduced brightness of the image. Do not use abrasive materials to clean the lens. The lights are located on the bottom of the mirror housings. This feature will project an image onto the ground a short distance from the vehicle whenever illuminated entry and exit is activated.
Windows and Mirrors C B 89 The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C).
90 Windows and Mirrors SUN VISORS Slide-On-Rod Rotate the visor toward the side window and extend it rearward for extra sunlight coverage. Retract the visor before moving it back toward the windshield and storing it. Illuminated Visor Vanity Mirror Lift the cover to switch on the lamp.
Windows and Mirrors 91 Flexible Visor Storage System The system can accommodate various storage accessories. A sunglasses clip and multi-function clip are provided. To attach one of the accessories, do the following: 1. Insert the provided removal tool (on the accessory holder) or a coin into the slot on the plug and rotate one-quarter turn in either direction to remove. It may be necessary to rotate the visor until the plug drops away from the opening.
92 Instrument Cluster GAUGES Type 1 Cluster shown in standard measure. Metric similar. A. Speedometer B. Fuel gauge C. Engine coolant temperature gauge D. Tachometer E. Information display. See Information displays for more information. Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when the ignition is on). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The fuel icon and arrow indicates which side of the vehicle the fuel filler door is located.
Instrument Cluster 93 Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. WARNING: Never remove the coolant reservoir cap while the engine is running or hot. Type 2 A B C E D Cluster shown in standard measure. Metric similar. A. Speedometer B.
94 Instrument Cluster Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when the ignition is on). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The fuel icon and arrow indicates which side of the vehicle the fuel filler door is located. Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range.
Instrument Cluster 95 Brake System Warning Light To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the on position when the engine is not running, or in a position between on and start, or by applying the parking brake when the ignition is turned to the on position. If it illuminates when you are driving, check that the parking brake is not engaged.
96 Instrument Cluster High Beams Illuminates when the high beam headlamps are on. Low Fuel Illuminates when the fuel level in the fuel tank is at or near empty. Low Tire Pressure Warning Illuminates when your tire pressure is low. If the light remains on at start-up or while driving, the tire pressure should be checked. When the ignition is first turned to on, the light will illuminate for three seconds to ensure the bulb is working.
Instrument Cluster 97 Service Engine Soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present.
98 Instrument Cluster Stability Control System Off Illuminates when AdvanceTrac®/Traction control has been disabled by the driver. Turn Signal Illuminates when the left or right turn signal or the hazard warning flasher is turned on. If the indicators stay on or flash faster, check for a burned out bulb. Upshift (if equipped) To maximize fuel economy, this light illuminates when the manual transmission should be shifted to the next highest gear.
Information Displays 99 GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle. We recommend against the use of any handheld device while driving and that you comply with all applicable laws.
100 Information Displays MYKEY MILES (km) For more information, see the MyKey® chapter. MILES (km) TO E This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel. AVG MPG (L/100 km) Average fuel economy displays your average fuel economy in miles/gallon or liters/100 km.
Information Displays 101 RESET FOR SYSTEM CHECK When this message appears, press the RESET button and the information display will begin to cycle through the following systems and provide a status of the item if needed. 1. XXX% OIL LIFE 2. CHARGING SYSTEM 3. DOORS STATUS 4. TRUNK STATUS 5. BRAKE SYSTEM 6. FUEL LEVEL 7. MYKEY DISTANCE (if MyKey® is programmed) 8. MYKEY(S) PROGRAMMED 9. ADMIN KEYS PROGRAMMED Note: Some systems show a message only if a condition is present.
102 Information Displays STEERING FEEL This feature allows three modes of steering feel. Press RESET to cycle through the settings of: • STANDARD– Provides a balance between a comfort and sport feel. • SPORT– Slightly higher effort required for steering with more road force felt through the steering wheel. See note below. • COMFORT– Slightly less effort required for steering with less road force felt through the steering wheel.
Information Displays 103 HALO COLOR: You can select one of the preset colors for halo lighting. Note: Headlamps or parking lamps must be on to set up colors. To choose colors for the gauges, halo color or ambient lighting do the following: 1. Press SETUP to reach the GAUGE COLOR, AMBIENT COLOR, or HALO COLOR menu. 2. Press RESET to scroll through the following color options: • ICE BLUE • BLUE • WHITE • ORANGE • GREEN • RED • PURPLE UNITS Displays the current units English or Metric.
104 Information Displays LANGUAGE = ENGLISH / SPANISH / FRENCH Allows you to choose which language for the information display. Selectable languages are English, Spanish, or French. Waiting four seconds or pressing the RESET button cycles through each of the language choices. Press and hold RESET for two seconds to set the language choice. Information Messages See Information Messages later in this chapter for more information.
Information Displays • Settings • Information †Gauge Mode Air/Fuel Ratio Virtual gauge shown Vacuum inHG / Virtual gauge shown Boost psi (Shelby® GT500®) Cyl Head Virtual gauge shown Inlet Air Virtual gauge shown Oil Press. No virtual gauge available Oil Temp. Virtual gauge shown Trans temp Virtual gauge shown (auto transmission only) Voltage Virtual gauge shown †See Virtual Gauges later in this section for more information.
106 Information Displays Fuel Economy Instant MPG (L/100km) mi (km) to E AVG MPG (L/100km) Fuel Hist.: shows Duration: 5 Minutes, 10 Minutes, 30 Minutes, Last 5 fuel usage as a Resets. The graph is updated each minute with the bar graph based fuel economy that was achieved during the prior 5, 10, 30 minutes of driving. on time. The duration time can be changed. Fuel Econ.
Information Displays Driver Assist Vehicle 107 Settings Rear Park Aid On/Off Autolamp Delay Off or XXX seconds Locks Autolock On/Off Autounlock On/Off Menu Control Standard: With standard set, pressing the up/down arrows from a lower level menu will escape to the main menu. Memory On: With memory on set, pressing the up/down arrows will navigate to the previous lower level menu.
108 Vehicle Information Displays Settings Dampers Sport / Normal (Shelby® GT500®) Steering Feel Standard Sport Comfort 2014 05+ Mustang (197) Owners Guide gf, 1st Printing, November 2012 USA (fus) Sport Locked: This will display when AdvanceTrac® sport mode is on or when AdvanceTrac® and traction control are off. The steering feel will be locked in sport mode and steering feel will not be selectable.
Information Displays †MyColor (if equipped) MyKey *Language 109 Settings Ice Blue, White, Green, Purple, Blue, Orange, Red, MyColor 1, 2, 3 Halo Halo Light On/Off Halo Color Ice Blue, White, Green, Purple, Blue, Orange, Red, MyColor 1, 2, 3 Ambient Light Ambient Light On/Off Ambient Dim High/Low Ambient Color Ice Blue, White, Green, Purple, Blue, Orange, Red, MyColor 1, 2, 3 1–5 Set MyColor 1, 2, Red 3 (create your own color by Green adjusting the levels (1–5) of the three primary Blue colors – red, gre
110 Information Displays Settings Units English or Metric System Reset Hold OK to Reset System to Factory Default †The instrument cluster gauges are backlit white when the headlamps are off. When the headlamps are on, you can select one of the preset colors or MyColor 1, 2, 3 for the nighttime gauge backlighting. A gauge in a warning condition will be backlit red when the headlamps are on. *Track Application features and messages in the information display are only available in English.
Information Displays 111 Average MPG (L/100km) Shows the average distance traveled per unit of fuel used for a given trip. Odometer Registers the total mileage of the vehicle. VIRTUAL GAUGES Note: In order to provide real-time values, some gauges may display more value fluctuation than others during normal operation. Some gauges shown in standard measure. Metric similar. AIR FUEL RATIO Displays the current air to fuel mixture in the engine.
112 Information Displays INLET AIR TEMP Displays the temperature of the air in the cold air inlet tube. OIL TEMP Displays the engine oil temperature. If the temperature rises to the red area, stop in a safe place and let the vehicle cool. If the problem persists, see your authorized dealer. TRANS TEMP (Automatic Transmission only) Displays the transmission fluid operating temperature. If the temperature rises to the red area, stop in a safe place and let the transmission cool.
Information Displays 113 TRACK APPS (IF EQUIPPED) WARNING: Track Apps is for track use only. Remember that even advanced technology cannot defy the laws of physics. It is always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage. Note: Track Apps are for track use only.
114 Information Displays Acceleration Timer Displays the vehicle’s rate of acceleration. 1. Choose desired speed or distance. 2. Choose Automatic Start or Countdown Start. 3. Follow the on-screen prompts. Brake Performance Displays the vehicle’s rate of deceleration. 1. Choose desired speed to start recording data. 2. Follow the on-screen prompts. Dashboard Screen (Shelby® GT500®) For dashboard screen information, see the Shelby GT500 Supplement.
Information Displays Alarm/Security Messages TO STOP ALARM START VEHICLE SECURITY EVENT OCCURRED Battery and Charging System Messages CHECK CHARGING SYSTEM Brake System Messages BRAKE FLUID LEVEL LOW CHECK BRAKE SYSTEM PARK BRAKE ENGAGED Door Messages X DOOR AJAR TRUNK AJAR 115 Action / Description Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on the driver’s side door.
116 Information Displays Fuel Messages CHECK FUEL FILL INLET FUEL LEVEL LOW Action / Description Displayed when the fuel fill inlet may not be properly closed. Displayed as an early reminder of a low fuel condition. Key Messages COULD NOT PROGRAM INTEGRATED KEY Action / Description Displayed when an attempt is made to program a fifth integrated key. For more information, see the Security chapter.
Information Displays MyKey® Messages MYKEY ACTIVE DRIVE SAFELY ADVTRAC ON MYKEY SETTING 117 Action / Description Displayed when MyKey® is active. Displayed when a MyKey® is in use when trying to disable the AdvanceTrac® system and the optional setting is on. VEHICLE SPEED Displayed when a MyKey® is in use and the MyKey speed limit is on and the vehicle speed 80 MPH MAX is 80 mph (130 km/h).
118 Information Displays Park Aid Messages Action / Description CHECK REAR PARK Displayed when the transmission is in R (Reverse) and the park aid is disabled. AID Tire Messages LOW TIRE PRESSURE TIRE PRESSURE MONITOR FAULT TIRE PRESSURE SENSOR FAULT Action / Description Displays when one or more tires on your vehicle have low tire pressure. Displays when the tire pressure monitoring system is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer.
Information Displays 119 Compass Zone Adjustment When something affects the compass readings, typically the compass corrects itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. 1. Determine which magnetic zone you are in for your geographic location by referring to the zone 3 2 1 15 map. 4 14 2. Turn ignition to the on position. 13 3.
120 Audio System GENERAL INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Distance and strength Terrain Station overload Radio reception factors The further you travel from an FM station, the weaker the signal and the weaker the reception.
Audio System 121 MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracks and folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the MP3 disc. The player numbers each MP3 track on the disc (noted by the .mp3 file extension) from T001 to a maximum of T255.
122 Audio System AM/FM/CD/SIRIUS SATELLITE RADIO S R Q P O N 1 2 3 4 •DIRECT TEXT SCAN CAT/FOLD 5 6 8 7 0 9 MENU CLOCK # SOUND PHONE SEEK A B C D E F G LOAD VOL M L AM/FM CD SIRIUS AUX K J TUNE OK H I WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Audio System 123 Note: Autoset does not delete your original preset stations. Note: In order to re-run the autoset features, you must first turn it off before turning it back on. B. MENU: Press this button to access different audio features: • Compression brings the soft and loud CD passages together for a more consistent listening level. • Shuffle plays the current CD tracks in random order.
124 Audio System I. AUX: Press this button to access media through your auxiliary input jack. If your vehicle is equipped with SYNC®, see the SYNC® chapter for more information. J. CD: Press the CD button to access CD and MP3 modes. • The disc begins to play where it left off. If no CD is loaded, NO DISC appears in the display. • Press the SEEK buttons to access the previous or next track. Press and hold the SEEK buttons to quickly reverse or fast forward within the same track. K.
Audio System 125 Q. DIRECT: • In radio mode, press this button to select the desired radio frequency (such as 93.9) using the memory preset numbers (0–9). • In SIRIUS mode, press this button to enter the desired channel (such as 002) using the memory preset buttons. If you only enter one digit, and press OK, the system goes to that channel. If you enter three digits, the system automatically goes to that channel, if available. You may cancel your entry by pressing DIRECT.
126 Audio System WARNING: For safety reasons, do not connect or adjust the settings on your portable music player while your vehicle is moving. WARNING: Store the portable music player in a secure location, such as the center console or the glove box, when your vehicle is moving. Hard objects may become projectiles in a crash or sudden stop, which may increase the risk of serious injury.
Audio System 127 6. Press AUX until LINE or LINE IN appears in the display. You should hear music from your device even if it is low. 7. Adjust the volume on your portable music player until it reaches the volume level of the FM station or CD. Do this by switching back and forth between the AUX and FM or CD controls. USB PORT (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, crash and injury.
128 Audio System SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels SIRIUS® broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. For more information and a complete list of SIRIUS satellite radio channels, visit www.siriusxm.com in the United States, www.sirius.ca in Canada, or call SIRIUS at 1–888–539–7474. Note: This receiver includes the eCos real-time operating system. eCos is published under the eCos License.
Audio System 129 SIRIUS Satellite Radio Service Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes. SIRIUS satellite radio is a subscription-based satellite radio service that broadcasts a variety of music, sports, news, weather, traffic and entertainment programming.
130 Radio display Invalid Channel Audio System Condition The channel is no longer available. Unsubscribed Channel Your subscription does not include this channel. No Signal Updating Call SIRIUS 1–888–539–7474 The signal is lost from the SIRIUS satellite or SIRIUS tower to your vehicle antenna. Update of channel programming in progress. Your satellite service is no longer available. No Channels Available All the channels in the selected category are either skipped or locked.
Climate Control 131 MANUAL HEATING AND AIR CONDITIONING SYSTEM A B C D R E A/C K MAX A/C F J G I H A. Defrost: Distributes air through the windshield defroster vents and demister vents. This setting can also be used to defog and clear the windshield of a thin covering of ice. B. Rear defrost: Turns the heated windows and mirrors off and on. See Heated windows and mirrors later in this chapter for more information. C.
132 Climate Control D. A/C: Press to turn air conditioning off and on. Air conditioning cools the vehicle using outside air. To improve air conditioning when starting your vehicle, drive with the windows slightly open for two to three minutes. E. Recirculated air: Press to switch between outside air and recirculated air. When the LED on the button is lit, the air currently in the passenger compartment is being recirculated.
Climate Control 133 DUAL ZONE AUTOMATIC TEMPERATURE CONTROL SYSTEM (WITH NAVIGATION SYSTEM) A B L C K D J E I H G F Note: To use the touchscreen controls, see the Touchscreen climate controls in the Navigation System chapter. A. CLIMATE: Control the system through the touchscreen display. See Touchscreen functions later in this section. B. Rear defrost: Turns the heated windows and mirrors off and on. See Heated windows and mirrors later in this chapter for more information.
134 Climate Control F. Recirculated air: Press to switch between outside air and recirculated air. When the LED on the button is lit, the air currently in the passenger compartment is being recirculated. Using recirculated air can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle. Note: Recirculated air engages automatically when MAX A/C is selected or can be turned on manually in any airflow mode except Defrost. G.
Climate Control 135 • Remove any snow, ice or leaves from the air intake area at the base of the windshield. • To improve the A/C cool down, drive with the windows slightly open for 2-3 minutes after start-up or until the vehicle has been aired out. • A small amount of air may be felt from the floor vent regardless of the air distribution setting that is selected.
136 Climate Control • To improve the A/C cool down, drive with the windows slightly open for 2-3 minutes after start-up or until the vehicle has been aired out. • A small amount of air may be felt from the floor vent regardless of the air distribution setting that is selected.
Climate Control 137 Heated Exterior Mirror (If Equipped) Note: Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass that has frozen in place. These actions could cause damage to the glass and mirrors. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Both mirrors heat to remove ice, mist and fog when you turn the rear window defroster on.
138 Seats SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seat back, with your feet on the floor.
Seats 139 • Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 inches (250 millimeters) between your breastbone and the airbag cover. • Hold the steering wheel with your arms slightly bent. • Bend your legs slightly so that you can press the pedals fully. • Position the shoulder strap of the safety belt over the center of your shoulder and position the lap strap tightly across your hips.
140 Seats To adjust the head restraint, do the following: A B C D Front Seat Head Restraints (If Equipped) The head restraints consist of: A. An energy absorbing head restraint B. Two steel stems C. Guide sleeve adjust and release button D. Guide sleeve unlock and remove button • Raise: Pull up on the head restraint (A). • Lower: Press and hold the guide sleeve adjust and release button (C) and push down on the head restraint (A).
Seats 141 Rear Seat Non-adjustable Outboard Head Restraints The second row outboard non-adjustable head restraints can be rotated forward to improve rear vision when there are no rear occupants. The non-adjustable head restraints A consist of: A. a trimmed energy absorbing foam and structure B. a rotation button. B Press the rotation button to rotate the head restraint forward in order to improve rear vision when there are no rear seat occupants.
142 Seats MANUAL SEATS WARNING: Do not adjust the driver’s seat or seat back while the vehicle is moving. WARNING: Rock the seat backwards and forwards after releasing the lever to make sure that it is fully engaged.
Seats 143 WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. Adjusting the height of the driver’s seat POWER SEATS (IF EQUIPPED) WARNING: Never adjust the driver’s seat or seat back when the vehicle is moving. WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are not trapped behind the seat back. The power seat control is located on the outboard side of the seat.
144 Seats Power Lumbar (If Equipped) The power lumbar control is located on the top of the driver’s seat side shield. Press one side of the control to increase lower back firmness. Press the other side of the control to decrease lower back firmness.
Seats 145 To operate the heated seats: • Press to activate. • Press again to deactivate. REAR SEATS Rear Seat Entry and Exit Use the seat back release to fold the back of the front seat forward for rear seat access. This release handle is located on the upper back of the front seat. The seat back locks automatically when returned to the normal position. Use the recliner handle to return the seat back to the desired position.
146 Seats 2nd Row Seat/Split-Folding Rear Seat (If Equipped) WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are not trapped behind the seat back. After returning the seat back to its original position, pull on the seat back to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash. One or both rear seat backs (coupe only) can be folded down to provide additional cargo space.
Universal Garage Door Opener (If Equipped) 147 HOMELINK® WIRELESS CONTROL SYSTEM (IF EQUIPPED) WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. WARNING: Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).
148 Universal Garage Door Opener (If Equipped) Programming Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal. 1. With your vehicle parked outside of the garage and your key in the ignition, turn the key so that the ignition is in the on position. 2. Hold your hand-held, garage door transmitter 1–3 inches (2–8 centimeters) away from the HomeLink button you want to program. 3.
Universal Garage Door Opener (If Equipped) 149 After programming the HomeLink button, follow Steps 5 – 7 as listed below to program your garage door opener. Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener. 5. Press the learn button on the garage door opener motor, and then you have 30 seconds to complete the next step. 6. Return to your car. 7. Press and hold the function button you want to program for two seconds, then release.
150 Universal Garage Door Opener (If Equipped) Programming HomeLink® to a Genie Intellicode® 2 garage door opener Note: The Genie Intellicode® 2 transmitter must already be programmed to operate with the garage door opener. Programing the transmitters To program HomeLink® to the transmitter you must first put the transmitter into programming mode. To do this: A. Red LED B. Green LED A B 1. Press and hold one of the buttons on the hand-held transmitter for 10 seconds.
Universal Garage Door Opener (If Equipped) 151 Programming HomeLink® to the Genie Intellicode® garage door opener motor Note: You may need a ladder to access the garage door opener motor. To program HomeLink® to the garage door opener motor: 1. Press and hold the PROGRAM button on the garage door opener motor until both blue LED’s turn on. 2. Release the PROGRAM button. Only the smaller round LED should be on. 3. Press and release the program button.
152 Auxiliary Power Points AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. Note: If used when the engine is not running, the battery will discharge. There may be insufficient power to restart your engine. Note: Do not insert objects other than an accessory plug into the power point.
Storage Compartments 153 CENTER CONSOLE Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. Available console features include: • Cupholders in the front of the console (Pull the door open to access.) Remove the spacer from the cupholder to hold deeper cups. • Lockable storage bin (Use the ignition key to lock or unlock the console bin and press the latch to open the console.
154 Starting and Stopping the Engine GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Do not start your vehicle in a closed garage or in other enclosed areas.
Starting and Stopping the Engine 155 IGNITION SWITCH C B D A A. Off: The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. B. Accessory: Allows the electrical accessories such as the radio to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. C.
156 Starting and Stopping the Engine Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. If your vehicle is equipped with a manual transmission, fully press the clutch pedal also. 2. Turn the key to the start position to start the engine. Release the key when the engine starts. Note: The engine may continue cranking for up to 15 seconds or until it starts. Note: If you cannot start the engine on the first try, wait for a short period and try again.
Starting and Stopping the Engine 157 Guarding Against Exhaust Fumes WARNING: If you smell exhaust fumes inside your vehicle, have this checked immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and leave the engine idling for long periods of time, we recommend that you do one of the following: • Open the windows at least 1 inch (2.
158 Starting and Stopping the Engine • Make sure that when in operation, the extension cord plug and the heater cord plug connections are free and clear of water. This could cause an electric shock or fire. • Make sure your vehicle is parked in a clean area, clear of combustibles. • Make sure the heater, heater cord and extension cord are firmly connected. • Check for heat anywhere in the electrical hookup once the system has been operating for approximately 30 minutes.
Fuel and Refueling 159 SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. WARNING: Automotive fuels can cause serious injury or death if misused or mishandled.
160 Fuel and Refueling • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water.
Fuel and Refueling 161 Octane Recommendations • 3.7L V6 engine Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as Regular with an octane rating below 87, particularly in high altitude areas. Do not use fuels with octane posted on pump below 87. • 5.0L V8 engine Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended.
162 Fuel and Refueling Refilling with a Portable Fuel Container WARNING: Do not insert the nozzle of a portable fuel container or aftermarket funnel into the capless fuel system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, which could result in serious personal injury. WARNING: Do not try to pry open or push open the capless fuel system with foreign objects.
Fuel and Refueling 163 REFUELING • • • • • • • WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: Read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, flames and smoking materials away from fuel.
164 Fuel and Refueling 4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about 10 seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuel filler nozzle.
Fuel and Refueling 165 For consistent results when filling the fuel tank: • Turn the ignition off before fueling; an inaccurate reading results if the engine is left running. • Use the same fill rate (low–medium–high) each time the tank is filled. • Allow no more than two automatic click–offs when filling. Results are most accurate when the filling method is consistent.
166 Fuel and Refueling EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Fuel and Refueling 167 Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal also lists engine displacement.
168 Fuel and Refueling Readiness for Inspection/Maintenance (I/M) Testing Some state, provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. If the service engine soon indicator is on or the bulb does not work, the vehicle may need to be serviced. See On-board Diagnostics (OBD-II) in this chapter.
Transmission 169 AUTOMATIC TRANSMISSION (IF EQUIPPED) WARNING: Always set the parking brake fully and make sure the gearshift is latched in position P. Turn the ignition off and remove the key whenever you leave your vehicle. P Your vehicle has been designed to improve fuel economy by reducing fuel usage while coasting or decelerating.
170 Transmission Position S Moving the gearshift lever to position: • Provides additional grade (engine) braking and extends lower gear operation to enhance performance for uphill climbs, hilly terrain or mountainous areas. This will increase engine RPM during engine braking. • Provides additional lower gear operation through the automatic transmission shift strategy which reacts to vehicle inputs (vehicle acceleration, accelerator pedal, brake pedal and vehicle speed).
Transmission 171 Note: Some models have a blink feature (if equipped). If manually selecting a gear that is out of the current vehicle speed range, the vehicle will not make the requested shift and will blink the current gear. Brake-shift interlock WARNING: Do not drive your vehicle until you verify that the brakelamps are working. WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely.
172 Transmission 3. Lift the center console upward to access the base of the gear shifter assembly and locate the brakeshift interlock override lever. 4. Press and hold the lever forward while pulling the gearshift lever out of the P (Park) position and into the N (Neutral) position. 5. Reinstall the console and chrome bezel. 6. Start the vehicle.
Transmission 173 MANUAL TRANSMISSION (IF EQUIPPED) Using the Clutch Manual transmission vehicles have a starter interlock that prevents starting the engine unless the clutch pedal is fully pressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in the neutral position. 3. Start the engine. 4. Press the brake pedal and move the gearshift lever to the desired gear; position 1 or position R. 5.
174 Transmission Recommended Shift Speeds Note: Do not downshift into position 1 when your vehicle is moving faster than 15 mph (24 km/h). This may damage the clutch or transmission. Upshift according to the following charts. For the 3.7L V6 with 2.73 axle ratio, shift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1-2 15 mph (24 km/h) 2-3 25 mph (40 km/h) 3-4 40 mph (64 km/h) 4-5 45 mph (72 km/h) 5-6 50 mph (80 km/h) For the 3.7L V6 with 3.
Transmission 175 Reverse Note: The gearshift lever can only be moved to position R by pushing the knob down before shifting to reverse. This is a lockout feature which protects the transmission from accidentally engaging position R when intending to select position 1. 1. Make sure that your vehicle is at a complete stop before you shift into position R . Failure to do so may damage the transmission. 2. Press the clutch pedal to the floor to disengage clutch. 3.
176 Transmission AXLE INFORMATION Traction-Lok™ Axle (If Equipped) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok™ axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a Traction-Lok™ rear axle could result in a permanent reduction in effectiveness.
Transmission 177 This feature makes it easier to pull away when the vehicle is on a slope without the need to use the parking brake. When this feature is active, the vehicle will remain stationary on the slope for two to three seconds after you release the brake pedal. This allows you time to move your foot from the brake to the accelerator pedal. The brakes are released automatically once the engine has developed sufficient drive to prevent the vehicle from rolling down the slope.
178 Transmission 5. Rotate the steering wheel at least one full turn to the right and return the steering wheel to the original starting position. 6. Rotate the steering wheel at least one full turn to the left and return the steering wheel to the original starting position. 7. Slowly press and release the brake pedal five times – ensure the brake pedal is completely released each time.
Brakes 179 GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn out and should be inspected by an authorized dealer. If your vehicle has continuous vibration or shudder in the steering wheel while braking, you should take it to an authorized dealer for inspection. Note: Brake dust may accumulate on the wheels, even under normal driving conditions.
180 Brakes HINTS ON DRIVING WITH ANTI-LOCK BRAKES When the system is operating, the brake pedal will pulse and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal. The anti-lock braking system will not eliminate the dangers inherent when: • you drive too closely to the vehicle in front of you. • your vehicle is hydroplaning. • you take corners too fast. • the road surface is poor.
Traction Control 181 PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels spin when accelerating on slippery or loose surfaces, the system reduces engine power in order to increase traction.
182 Stability Control PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel or tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceTrac® system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac® system.
Stability Control 183 A Vehicle without AdvanceTrac® skidding off its intended route. B Vehicle with AdvanceTrac® maintaining control on a slippery surface. USING ADVANCETRAC® The system automatically is enabled when you start your engine. The electronic stability control portion of the system is disabled when the transmission is in position R or, on some models, if the stability control button is pressed and held for more than five seconds when the brakes are applied and the vehicle is at a stop.
184 Button functions Button pressed twice; brakes applied Button pressed and held more than 5 seconds; brakes applied; no throttle Button pressed again after deactivation Stability Control AdvanceTrac® Features Icon Mode ESC status TCS Sport mode (if equipped) On Enabled Enabled AdvanceTrac® Disabled On Disabled Disabled AdvanceTrac® fully enabled Off Enabled Enabled Note: Sport mode is not intended to be used on public roadways.
Parking Aids 185 SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds. Traffic control systems, inclement weather, air brakes, and external motors and fans may also affect the function of the sensing system; this may include reduced performance or a false activation.
186 Parking Aids The system can be turned off using the information display control. See the Information Display chapter. If a fault is present in the system, a warning message appears in the information display and does not allow the driver to switch the faulted system on. Using the Rear Sensing System The rear sensors are only active when the transmission is in R. As the vehicle moves closer to the obstacle, the rate of the audible warning increases.
Parking Aids 187 REAR VIEW CAMERA SYSTEM (IF EQUIPPED) WARNING: The rear view camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the interior and exterior mirrors for maximum coverage. WARNING: Objects that are close to either corner of the bumper or under the bumper, might not be seen on the screen due to the limited coverage of the camera system.
188 Parking Aids Using the Rear View Camera System The rear view camera system displays what is behind your vehicle when you place the transmission in R. The system uses fixed guidelines which show the actual path the vehicle is moving in while reversing in a straight line. This can be helpful when backing into a parking space or aligning the vehicle with another object behind the vehicle. Note: Do not use the camera system if the trunk is ajar.
Parking Aids 189 Guidelines Note: The guidelines are only available when the transmission is in R. A. Rear bumper B. Fixed guideline: Red zone D C. Fixed guideline: Yellow zone C D. Fixed guideline: Green zone B A The fixed guidelines fade in and out depending on the steering wheel position. Always use caution while reversing. Objects in the red zone are closest to your vehicle and objects in the green zone are further away.
190 Cruise Control PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved. Note: Vehicle speed may vary momentarily when driving up or down a steep hill. Apply the brakes if your vehicle speed increases above the set speed while driving downhill.
Cruise Control 191 Changing the Set Speed Note: If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, you will return to the speed that you previously set. • Press and hold SET+ or SET-. Release the control when you reach the desired speed. • Press and release SET+ or SET-. The set speed will change in approximately 1 mph (2 km/h) increments. • Press the accelerator or brake pedal until you reach the desired speed.
192 Driving Aids STEERING Electric Power Steering WARNING: Obtain immediate service if a system error is detected. You may not notice any difference in the feel of your steering, but a serious condition may exist. Failure to do so may result in loss of steering control. Note: Your vehicle is equipped with an electric power-assisted steering system. There is no fluid reservoir to check or fill.
Driving Aids 193 Selectable Steering Note: The steering setting defaults to standard if the battery is disconnected or removed. See the Information Displays chapter. You can select the desired steering feel using the information display control. The settings are: • Standard: Default factory setting. • Sport: Slightly higher effort required for steering with more road force felt through the steering wheel.
194 Load Carrying LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance.
Load Carrying 195 WARNING: The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.
196 Load Carrying Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear).
Load Carrying 197 • Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.
198 Load Carrying GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at GVWR, not at GCWR.
Load Carrying 199 Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
200 Load Carrying • Suppose your vehicle has a 1400 lb. (635 kg) cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (45 kg) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 lb.
Towing 201 TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. Note: For information on electrical items such as fuses or relays, see the Fuses chapter.
202 Towing RECOMMENDED TOWING WEIGHTS Note: Do not tow with the Shelby GT500 model. It cannot tow a trailer. Note: Do not exceed the trailer weight for your vehicle configuration listed in the chart below. Note: Make sure to take into consideration trailer frontal area. Do not exceed 12 feet2 (1.11 meters2) trailer frontal area. Note: For high altitude operation, reduce the gross combined weight by 2% per 1000 feet (300 meters) starting at the 1000 foot (300 meter) elevation point.
Towing 203 Hitches Do not use a hitch that either clamps onto the bumper or attaches to the axle. Distribute the trailer load so 10-15% of the total trailer weight is on the tongue. Safety Chains Note: Never attach safety chains to the bumper. Always connect the safety chains to the hook retainers of your vehicle hitch. To connect the safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground.
204 Towing When Towing a Trailer • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 kilometers). • Do not make full-throttle starts. • Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 miles (80 kilometers).
Towing 205 Exceeding these limits may allow water to enter vehicle components: • Causing internal damage to the components. • Affecting driveability, emissions, and reliability. Replace the rear axle lubricant anytime the rear axle has been submerged in water. Water may have contaminated the rear axle lubricant, which is not normally checked or changed unless a leak is suspected or other axle repair is required.
206 Towing The rear wheels (drive wheels) must be on a tow dolly when towing your vehicle from the front using wheel lift equipment. This prevents damage to the transmission. The front wheels should be on a tow dolly when towing your vehicle from the rear using wheel lift equipment. This prevents damage to the front fascia.
Convertible Top (If Equipped) 207 OPENING THE CONVERTIBLE TOP Note: Do not store articles behind rear seat. Articles stored in the convertible top stowage compartment may break the rear glass window when the top is opened. Note: Opening the convertible top when the top material is wet may cause mold or mildew. The convertible top can be opened with the side windows down. The windows will automatically lower when opening or closing the top.
208 Convertible Top (If Equipped) 3. Unclamp the top from the windshield header by pulling each latch handle down and then rotating the latch to the rear until it clears the header. Note: If the top has not been opened for some time and sticks to the windshield header, push the front of the top up slightly with your hand to loosen it. 4. Press and hold the convertible top switch on the overhead console until the windows are completely down and the top is completely stored.
Convertible Top (If Equipped) 209 USING THE BOOT Installing the Boot WARNING: Always secure the retaining clips and boot straps on the vehicle or the boot may come loose while driving. Note: Be sure the boot is secure on the vehicle before driving. Improper installation can result in loss or damage of the boot. 1. Install the boot on the vehicle by hooking the boot retaining clips on the back panel. 2.
210 Convertible Top (If Equipped) Removing the Boot 1. Unhook the boot straps from the rear seat hooks. 2. Push the boot down unhooking the boot retaining clips. 3. Lift the boot off the vehicle. Storing the Boot 1. Position the boot right-side up and fold each side of the boot inward. 2. Turn the boot upside down and fold the left side of the boot inward. 3. Fold the right side inward and secure the boot with the strap. Stow the boot in the trunk.
Convertible Top (If Equipped) 211 CLOSING THE CONVERTIBLE TOP Note: The convertible top will not operate unless the vehicle is stationary or traveling under 3 mph (5 kmh). Note: Make sure that the latch handles are pulled down and in the fully opened position before the top makes contact with the windshield header. This allows for hand clearance and proper closure of the top. To close the convertible top: 1. Bring the vehicle to a complete stop. The ignition must be on.
212 Driving Hints BREAKING-IN You need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unique driving characteristics. Avoid driving too fast during the first 1000 miles (1600 kilometers). Vary your speed frequently and change up through the gears early. Do not labor the engine. Do not tow during the first 1000 miles (1600 kilometers).
Driving Hints 213 • Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors, rollbars or light bars, running boards, ski racks). • Drive with the wheels out of alignment. DRIVING THROUGH WATER WARNING: Drive through water in an emergency only, and not as part of normal driving.
214 Driving Hints FLOOR MATS WARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
Driving Hints 215 WARNING (Continued) • Check attachment of floor mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning or replacement. • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Objects that are loose can become trapped under the pedals causing a loss of vehicle control.
216 Roadside Emergencies ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24 hours a day, seven days a week • for the coverage period listed on the Roadside Assistance Card included in your owner’s manual portfolio.
Roadside Emergencies 217 Vehicles Sold in the U.S.: Using Roadside Assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is found in the owner’s manual portfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673.
218 Roadside Emergencies FUEL CUT-OFF SWITCH WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision. In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off.
Roadside Emergencies 219 Preparing Your Vehicle Note: Use only a 12–volt supply to start your vehicle. Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 1. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 2. Check all battery terminals.
220 Roadside Emergencies 1 3 4 2 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor or fuel injection system.
Roadside Emergencies 221 Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. 4 2. Remove the jumper cable on the negative (-) terminal of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4.
222 Customer Assistance GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training, equipment or both, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance 223 • Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6K 0C8 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling or servicing authorized dealer. 2.
224 Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance 225 THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the Services You Need section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration.
226 Customer Assistance UTILIZING THE MEDIATION or ARBITRATION PROGRAM (CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers. In those cases, where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation or arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance 227 If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS & GLOBAL INITIATIVES Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.
228 Customer Assistance If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing expcac@ford.com. If you are in another foreign country, contact the nearest authorized dealer. In the event your inquiry is unresolved, communicate your concern with the dealership’s Sales Manager, Service Manager or Customer Relations Manager.
Customer Assistance 229 REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
230 Fuses CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components.
Fuses 231 FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power distribution box is located in the engine compartment. It has high-current fuses that protect your vehicle’s main electrical systems from overloads.
232 Fuses Fuse or relay number 3 4 5 6 7 8 9 10 11 12 Fuse amp rating — 30A* 20A* 40A* 40A* 40A* 30A* 30A* — 20A* 13 14 15 20A** 25A** 20A** 10A** 16 17 18 19 20 21 22 23 20A** 10A** 20A* 30A* 30A* 30A* 20A* 10A** 24 25 26 10A** 10A** 20A** 27 20A** 28 — Protected components Not used Blower motor relay Power point (body) Rear defroster relay Cooling fan relay Anti-lock brake system pump Wipers Anti-lock brake system valve Not used Differential fluid pump (Shelby only) Fuel pump relay (non-Shel
Fuses Fuse or relay number 29 30 31 32 33 34 35 36 37 38 39 40 Fuse amp rating 30A* — 30A* 30A* 30A* 30A* 40A* Diode — 15A** 5A** 15A** 41 42 G8VA relay G8VA relay 43 44 45 G8VA relay G8VA relay 5A** 46 5A** 233 Protected components Passenger front window Not used Passenger power seat Driver power seat Front amplifier (Shaker radio) Driver front window motor Convertible top motor Fuel diode Not used Fuel injectors (Shelby only) Heated mirrors Powertrain control module vehicle power 4 – ignition coi
234 Fuses Fuse or relay number 47 Fuse amp rating 15A** 48 15A** 49 15A** 50 51 52 53 54 55 56 57 58 Full Full Full Full Full Full ISO relay ISO relay ISO relay ISO relay ISO relay ISO relay — Full ISO relay High current relay * Cartridge Fuses ** Mini Fuses Protected components Powertrain control module vehicle power 1 Powertrain control module vehicle power 5 Powertrain control module vehicle power 2 – emissions related powertrain components Cooling fan relay (high) Blower motor relay Starter r
Fuses 235 Passenger Compartment Fuse Panel The fuse panel is located in the lower passenger side area behind the kick panel. Open the trim panel door and remove the fuse cover to access the fuses. Use the provided fuse puller tool to remove a fuse. It is located inside the fuse cover.
236 Fuses Fuse or relay number 6 7 8 9 10 Fuse amp rating 20A 10A 10A 15A 15A 11 12 13 14 10A 7.
Fuses Fuse or relay number 32 Fuse amp rating 10A 33 34 35 36 37 38 39 40 41 10A 5A 10A 5A 10A 20A 20A 20A 15A 42 43 44 45 10A 10A 10A 5A 46 7.
238 Maintenance GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers who are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialized tools developed specifically for servicing your vehicle.
Maintenance 239 Working with the Engine On WARNING: To reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Set the parking brake and shift to positionP. 2. Block the wheels. OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hood release handle located on the driver’s side kick panel. 2.
240 Maintenance UNDER HOOD OVERVIEW 3.7L V6 Engine B A H G C F A. Battery B. Engine oil dipstick C. Engine oil filler cap D. Brake fluid reservoir E. Air filter assembly F. Engine coolant reservoir G. Windshield washer fluid reservoir H.
Maintenance 5.0L V8 Engine A. Battery B. Engine oil filler cap C. Engine oil dipstick D. Brake fluid reservoir E. Air filter assembly F. Engine coolant reservoir G. Windshield washer fluid reservoir H.
242 Maintenance Engine Shield Some vehicles may be equipped with an aero-shield under the engine. Remove the front fasteners of the shield to gain access for service. This includes oil and filter changes. ENGINE OIL DIPSTICK A. MIN B. MAX A B ENGINE OIL CHECK Note: Check the level before starting the engine. Note: Make sure that the level is between the MIN and MAX marks. 1. Make sure that your vehicle is on level ground. 2.
Maintenance 243 Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by the American Petroleum Institute (API).
244 Maintenance Adding Engine Coolant WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Maintenance 245 • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. Unscrew the cap slowly. Any pressure will escape as you unscrew the cap. Add prediluted engine coolant meeting the Ford specification.
246 Maintenance Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection. What You Should Know About Fail-Safe Cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The fail-safe distance depends on ambient temperatures, vehicle load and terrain.
Maintenance 247 When Fail-Safe Mode is Activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to an authorized dealer. 3.
248 Maintenance TRANSMISSION FLUID CHECK Checking Automatic Transmission Fluid Note: Transmission fluid should be checked and, if required, added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. See your Scheduled Maintenance Information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e.
Maintenance 249 BRAKE AND CLUTCH FLUID CHECK Brake and clutch (if equipped) systems are supplied from the same reservoir. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately. POWER STEERING FLUID CHECK Your vehicle is equipped with an electric power steering (EPS) system.
250 Maintenance CHANGING THE VEHICLE BATTERY WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Maintenance 251 Battery Relearn Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2.
252 Maintenance CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place.
Maintenance 253 See Scheduled Maintenance Information for the appropriate intervals for changing the air filter element. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used. V6 engine V8 engine 1. Release the clamps that secure the air filter housing cover. 2. Remove the air filter element from the air filter housing. 3.
254 Maintenance Vertical Aim Adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 ft (7.6 m) away. • (1) 8 ft (2.4 m) • (2) Center height of lamp to ground • (3) 25 ft (7.6 m) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 ft (2.4 m) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well).
Maintenance 255 5. Then use a 7 mm Allen wrench or a Phillips screwdriver to adjust the vertical aim of the headlamp. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. 6. Close the hood and turn off the lamps. CHANGING A BULB Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design.
256 Maintenance 4. Rotate the socket counterclockwise and remove from the lamp assembly. 5. Carefully pull the bulb straight out of socket. Install the new bulb in reverse order. Replacing Front Sidemarker Bulb 1. Make sure the headlamp control is in the off position. 2. Remove the hex head screws attaching the underbody forward aeroshield. 3. Remove the underbody forward aeroshield to gain access to the front sidemarker assembly. 4. Rotate the socket counterclockwise and remove from the lamp assembly.
Maintenance 257 Replacing Fog Lamp Bulbs (V6) (if equipped) 1. Make sure the headlamp control is in the off position and open the hood. 2. Remove the hex head screws attaching the underbody forward aeroshield. 3. Remove the underbody forward aeroshield to gain access to the fog lamp assembly. 4. Disconnect the electrical connector from the bulb by pulling it straight off. 5. Rotate the bulb counterclockwise and remove from the lamp assembly. Install the new bulb in reverse order.
258 Maintenance Replacing Rear Sidemarker Lamp Bulbs 1. Make sure the headlamp switch is in the off position and locate the sidemarker on the rear bumper fascia. 2. Insert a flathead screwdriver between the rear of the sidemarker lens and the bumper fascia. 3. Push the screwdriver to the front of the vehicle and then slide it towards you to pop out the lamp assembly. 4. Carefully pull the bulb straight out of socket. Install the new bulb in reverse order. Replacing License Plate Lamp Bulbs 1.
Maintenance 259 BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized D.O.T. for North America and an E for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
260 Vehicle Care GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft® Bug and Tar Remover (ZC-42) Motorcraft® Custom Bright Metal Cleaner (ZC-15) Motorcraft® Detail Wash (ZC-3-A) Motorcraft® Dusting Cloth (ZC-24) Motorcraft® Engine Shampoo and Degreaser (U.S.
Vehicle Care 261 • Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Motorcraft® Bug and Tar Remover. • Note: Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash it off as soon as possible. • Remove any exterior accessories before entering a car wash.
262 Vehicle Care Convertible Top and Padded Molding For vinyl tops, wash with Motorcraft® Detail Wash. For cloth tops, wash with a high quality convertible top cleaner and protectant. • Do not use stiff bristle brushes or abrasive materials or cleaners. • Hot waxes applied by commercial car washes can affect the cleanability of vinyl material. • Using high water pressure or wand-type car washes against the convertible top and windows may cause water leaks and possible seal damage.
Vehicle Care 263 • Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage. • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations. • Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine. CLEANING THE WINDOWS AND WIPER BLADES The windows and wiper blades should be cleaned regularly.
264 Vehicle Care CLEANING THE INTERIOR WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a crash.
Vehicle Care 265 • Be certain to wash or wipe your hands clean if you have been in contact with certain products, such as insect repellent and suntan lotion, in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately.
266 Vehicle Care CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft® Wheel and Tire Cleaner. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water. • Never apply any cleaning chemical to hot or warm wheel rims or covers.
Vehicle Care 267 • Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration. Re-wax as necessary when the vehicle is washed. • Lubricate hood latch, all door latches and trunk lid hinges with a light grade oil. • Cover interior trim to prevent fading. • Keep all rubber parts free from oil and solvents. Engine • The engine oil and filter should be changed prior to storage, as used engine oil contains contaminates that may cause engine damage.
268 Vehicle Care Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 meters) every 15 days to lubricate working parts and prevent corrosion.
Wheels and Tires 269 TIRE CARE Information About Uniform Tire Quality Grading Tire Quality Grades apply to new pneumatic passenger car tires. The Tire Quality Grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires.
270 Wheels and Tires Temperature A B C WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Wheels and Tires 271 • Recommended inflation pressure: The cold inflation pressure found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position) or Tire Label located on the B-Pillar or the edge of the driver’s door. • B-pillar: The structural member at the side of the vehicle behind the front door. • Bead area of the tire: Area of the tire next to the rim.
272 Wheels and Tires Note: If your tire size does not begin with a letter, this may mean it is designated by either ETRTO (European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing Association). B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. D. R: Indicates a radial type tire. E.
Wheels and Tires 273 Letter rating Speed rating - mph (km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR. H. U.S. DOT Tire Identification Number (TIN): This begins with the letters DOT and indicates that the tire meets all federal standards.
274 Wheels and Tires • Temperature: The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. M. Maximum Inflation Pressure: Indicates the tire manufacturer’s maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire.
Wheels and Tires 275 Information on T Type Tires B A C D E T type tires have some additional information beyond those of P type tires. These differences are described below. T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire. A.
276 Wheels and Tires INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped).
Wheels and Tires 277 Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire.
278 Wheels and Tires Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type mini-spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at the higher of the front and rear inflation pressure as shown on the Tire Label. 6.
Wheels and Tires 279 Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed or suspected, have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended.
280 Wheels and Tires Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford.
Wheels and Tires 281 WARNING: To reduce the risk of serious injury, when mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.
282 Wheels and Tires Safety Practices WARNING: If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits. • Avoid fast starts, stops and turns.
Wheels and Tires 283 The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire Rotation Note: If your tires show uneven wear, ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire and wheel assembly.
284 Wheels and Tires USING SNOW CHAINS WARNING: Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford.
Wheels and Tires 285 TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge. See Inflating Your Tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.
286 Wheels and Tires When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
Wheels and Tires 287 To restore the full function of the tire pressure monitoring system, have the damaged road wheel and tire assembly repaired and remounted on your vehicle. For additional information, see Changing Tires with a Tire Pressure Monitoring System in this section. When You Believe Your System Is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air.
288 Low tire pressure warning light Flashing warning light Wheels and Tires Possible cause Customer action required Spare tire in use Repair the damaged road wheel and tire and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When Your Temporary Spare Tire is Installed in this section. TPMS If the tires are properly inflated malfunction and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible.
Wheels and Tires 289 CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However, if you must use a sealant, the tire pressure monitoring system sensor and valve stem on the wheel must be replaced by an authorized Ford dealer. WARNING: See Tire Pressure Monitoring System in this chapter for important information. If the tire pressure monitoring sensor becomes damaged, it will no longer function.
290 Wheels and Tires A dissimilar spare tire and wheel assembly is defined as a spare tire or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. 2.
Wheels and Tires 291 The usage of a full-size dissimilar spare tire and wheel assembly can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly, additional caution should be given to: • to
292 Wheels and Tires WARNING: Never get underneath a vehicle that is supported only by a jack. If the vehicle slips off the jack, you or someone else could be seriously injured. WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. WARNING: Always use the jack provided as original equipment with your vehicle.
Wheels and Tires 293 4. Remove the lug wrench, spare tire and jack. 5. Remove the center ornament from the wheel. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. The vehicle jacking points are shown here, and can be identified by the triangle markings on the vehicle. Details are depicted on the yellow warning label on the jack. Note: Jack at the specified locations to avoid damage to the vehicle.
294 Wheels and Tires 7. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.
Wheels and Tires 295 TEMPORARY MOBILITY KIT (IF EQUIPPED) Note: The temporary mobility kit sealant compound in the canister is to be used for one tire only. See your Ford authorized dealer for additional replacement sealant canisters. The kit is located in the spare tire well in the trunk. The kit consists of an air compressor to reinflate the tire and a sealing compound in a canister that will effectively seal most punctures caused by nails or similar objects.
296 Wheels and Tires General Information WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. Note: Do not use the temporary mobility kit if a tire has become severely damaged by driving the vehicle with a tire that has insufficient air pressure. Only punctured areas located within the tire tread can be sealed with the temporary mobility kit.
Wheels and Tires 297 • Do not allow the compressor to operate continuously for more than 15 minutes; this will help prevent the compressor from overheating. • Never leave the temporary mobility kit unattended when it is operating. • Sealant compound contains latex. Make sure that you use the non-latex gloves provided to avoid an allergic reaction. • Keep the temporary mobility kit away from children.
298 Wheels and Tires First Stage: Reinflating the Tire with Sealing Compound and Air WARNING: Do not stand directly over the temporary mobility kit while inflating the tire. If you notice any unusual bulges or deformations in the tire’s sidewall during inflation, stop and call roadside assistance. WARNING: If the tire does not inflate to the recommended tire pressure within 15 minutes, stop and call roadside assistance.
Wheels and Tires B 299 7. Push and turn dial (A) counterclockwise to the sealant position. Turn on the kit by pressing the on button (B). A 8. Inflate the tire to the pressure listed on the Tire Label located on the driver’s door or the door jamb area. Note: When the sealing compound is first added into the tire, the air pressure gauge reading on the compressor unit may indicate a higher value; this is normal and should be no reason for concern.
300 Wheels and Tires Second Stage: Checking Tire Pressure WARNING: If you are proceeding from the First Stage: Reinflating the Tire with Sealing Compound and Air section and have injected sealant in the tire and the pressure is below 20 psi (1.4 bar), stop and call roadside assistance. If tire pressure is above 20 psi (1.4 bar), continue to the next step. WARNING: The power plug may get hot after use and should be handled carefully while unplugging. Check the air pressure of your tires as follows: 1.
Wheels and Tires 301 What To Do After the Tire Has Been Sealed After using the temporary mobility kit to seal your tire, you will need to replace the sealant canister and clear tube (hose). Sealing compound and spare parts can be obtained and replaced at an authorized Ford Motor Company dealership or tire dealer. Empty sealant bottles may be disposed of at home.
302 Wheels and Tires 3. Using the yellow cap tool, press the tab located on the temporary mobility kit compressor housing while pulling up on the sealant canister. Installation of the sealant canister to the temporary mobility kit: 1. Align the sealant canister with the temporary mobility kit housing. 2. Once aligned, seat the sealant canister by lightly pushing down until you hear an audible click.
Wheels and Tires 303 3. Wrap the clear tube around the compressor housing. Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorized dealer for assistance. Be sure to check the sealant compound’s use-by date regularly. The use-by date is on the lower right hand corner of the label located on the sealant canister. The sealant canister should be replaced after four years.
304 Wheels and Tires TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
Capacities and Specifications 305 ENGINE SPECIFICATIONS Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 3.7L V6 Engine 227 Minimum 87 octane 1-4-2-5-3-6 Coil on plug 0.049–0.053 in (1.25-1.35 mm) 10.5:1 5.0L V8 Engine 302 Minimum 87 octane 1-5-4-8-6-3-7-2 Coil on plug 0.049–0.053 in (1.25–1.35 mm) 11.0:1 For Shelby GT500 octane requirements, see the Shelby GT500 Supplement. DRIVEBELT ROUTING 1.
Ford part name or equivalent Multi-Purpose Grease Motorcraft® Orange Antifreeze/Coolant Prediluted — 12.4 quarts (11.7L) (3.7L engine) 13.0 quarts (12.3L) (5.0L engine) 15.2 quarts (14.4L) (5.
2014 05+ Mustang (197) Owners Guide gf, 1st Printing, November 2012 USA (fus) Automatic transmission fluid2,4 Rear axle fluid1 Lock cylinders Engine oil with Track Pack7 Engine oil without Track Pack6 Item Ford part name or equivalent •Motorcraft® SAE 5W-20 Premium 6.0 quarts (5.7L) Synthetic Blend Motor Oil (US) (3.7L engine) •Motorcraft® SAE 5W-20 Full Synthetic Motor Oil (US) •Motorcraft® SAE 5W-20 Super Premium 8.0 quarts (7.6L) Motor Oil (Canada) (5.
2.7 quarts (2.6L) Fill as required Manual transmission fluid (3.7L engine)5 Manual transmission fluid (5.0L engine)5 Windshield washer fluid XT-11-QDC / WSS-M2C200-D2 ZC-32-A (US) CXC-37-(A, B, D and F) (Canada) / WSB-M8B16-A2/- - Motorcraft® Premium Windshield Washer Concentrate (US) Premium Quality Windshield Washer Fluid (Canada) Ford part number / Ford Specification Motorcraft® Dual Clutch Transmission Fluid Ford part name or equivalent Fuel tank 16.0 gallons — — (60.6L) 1 Add 4 oz.
Capacity Ford part name or Ford part number / equivalent Ford Specification 2 Automatic transmissions that require MERCON® LV should only use MERCON® LV fluid. See Scheduled Maintenance Information to determine the correct service interval. Use of any fluid other than the recommended fluid may cause transmission damage. 3 Add the coolant type originally equipped in your vehicle. 4 Approximate dry capacity, including cooler and tubes. Fluid level should be checked by an authorized dealer.
310 Capacities and Specifications MOTORCRAFT PART NUMBERS Component Air filter element Battery Oil filter Spark plugs1 Cabin air filter Windshield wiper blade 3.7L V6 engine 5.0L V8 engine FA-1897 FA-1897 BXT-96R-590 BXT-96R-590 FL-500-S FL-500-S SP520 SP519 FP53 FP53 WW-2201-PF (driver side) WW-2001-PF (passenger side) 1 For spark plug replacement, see your authorized dealer. See Scheduled Maintenance Information for the appropriate intervals for changing the spark plugs.
Capacities and Specifications 311 The Vehicle Identification Number (VIN) contains the following information: A. World manufacturer identifier B. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint Devices and their location C. Make, vehicle line, series, body type D. Engine type E. Check digit F. Model year G. Assembly plant H. Production sequence number.
312 Capacities and Specifications TRANSMISSION CODE DESIGNATION You can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents.
Accessories 313 ACCESSORIES For a complete listing of the accessories that are available for your vehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer.
314 Accessories Peace of mind • Remote start • Full vehicle covers • Vehicle security systems • Keyless entry keypad • Wheel locks • Locking fuel plug • Bumper mounted parking assist system* *Ford Licensed Accessories (FLA) are warranted by the accessory manufacturer’s warranty. Ford Licensed Accessories are fully designed and developed by the accessory manufacturer and have not been designed or tested to Ford Motor Company engineering requirements.
Ford Extended Service Plan 315 FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered the powerful protection of Ford ESP. It is the only extended service plan backed by Ford Motor Company, and provides “peace of mind” protection beyond the New Vehicle Limited Warranty coverage. Up to 500+ Covered Vehicle Components There are four, new-vehicle Extended Service Plans with different levels of coverage. Ask your dealer for details.
316 Ford Extended Service Plan Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. With Ford ESP, you minimize your risk for unexpected repair bills and rising repair costs. Avoid the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance Plan that covers items that routinely wear out.
Ford Extended Service Plan 317 FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company of Canada, Limited.
318 Scheduled Maintenance GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it. Keep all receipts for completed maintenance with the vehicle. Regular maintenance intervals for your vehicle have been established based upon rigorous testing.
Scheduled Maintenance 319 Protecting Your Investment Maintenance is an investment that will pay dividends in the form of improved reliability, durability and resale value. To maintain the proper performance of your vehicle and its emission control systems, it is imperative that scheduled maintenance be completed at the designated intervals.
320 Scheduled Maintenance Additives and Chemicals Ford Motor Company recommended additives and chemicals are listed in the owner manual and in the Ford Workshop Manual. Additional chemicals or additives not approved by Ford are not recommended as part of normal maintenance. Please consult your warranty information. Oils, fluids and flushing In many cases, fluid discoloration is a normal operating characteristic and, by itself, does not necessarily indicate a concern or that the fluid needs to be changed.
Scheduled Maintenance 321 Check every six months Safety belts and seat latches for wear and function. Safety warning lamps (brake, ABS, airbag, safety belt) for operation. Washer spray and wiper operation. Clean or replace blades as necessary. Multi-point Inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly. This can help identify potential issues and prevent major problems.
322 Scheduled Maintenance 2014 05+ Mustang (197) Owners Guide gf, 1st Printing, November 2012 USA (fus)
Scheduled Maintenance 323 NORMAL SCHEDULED MAINTENANCE AND LOG Intelligent Oil-Life Monitor® – 3.7L and 5.0L Engines Your vehicle is equipped with an Intelligent Oil-Life Monitor® that determines when the engine oil needs to be changed based on how your vehicle is used. By using several important factors in its calculations, the monitor helps reduce the cost of owning your vehicle and reduce environmental waste at the same time.
324 Scheduled Maintenance Normal Scheduled Maintenance* At every oil change Change engine oil and filter.** interval as indicated by Rotate tires, inspect tire wear and measure the information display tread depth. Perform multi-point inspection (recommended). Inspect automatic transmission fluid level. Consult dealer for requirements. Inspect brake pads, shoes, rotors, drums, brake linings, hoses and parking brake. Inspect engine cooling system strength and hoses. Inspect exhaust system and heat shields.
Scheduled Maintenance 325 Additional Maintenance Items1 Every 20000 miles Replace cabin air filter (if equipped). (32000 km) Every 30000 miles Replace engine air filter. (48000 km) At 100000 miles Change engine coolant.2 (160000 km) Every 100000 miles Replace spark plugs. (160000 km) Inspect accessory drive belt(s).3 Every 150000 miles Change automatic transmission fluid and filter. (240000 km) Change manual transmission fluid.
326 Scheduled Maintenance Maintenance Schedule Log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P
Scheduled Maintenance DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER
328 Scheduled Maintenance DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: D
Scheduled Maintenance 329 SPECIAL OPERATING CONDITIONS – 3.7L AND 5.0L ENGINES If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance. For specific recommendations, see your dealership service advisor or technician.
330 Scheduled Maintenance Operating in Dusty or Sandy Conditions Such as Unpaved or Dusty Roads Inspect frequently, Replace cabin air filter (if equipped). service as required Replace engine air filter. Every 5,000 miles Inspect the wheels and related components for (8,000 km) abnormal noise, wear, looseness or drag. Rotate tires, inspect tires for wear and measure tread depth. Change engine oil and filter. Every 5,000 miles (8,000 km) or 6 months Every 50,000 miles Change manual transmission fluid.
Scheduled Maintenance Special Operating Condition Log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE:
332 Scheduled Maintenance DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: D
Scheduled Maintenance 333 EXCEPTIONS Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks equipped with Ford-design axles are lubricated for life; do not check or change fluid unless a leak is suspected, service is required or the assembly has been submerged in water.
334 Scheduled Maintenance ENGINE COOLANT CHANGE RECORD Initial change After initial change 3.7L and 5.0L Engines* Six years or 100000 miles (160000 km) (whichever comes first) Every three years or 50000 miles (80000 km) * Shelby GT500 owners: See the Shelby GT500 supplement.
SYNC® 335 SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist®, Vehicle Health Report and SYNC Services (Traffic, Directions & Information) (if equipped). • Use applications, such as Pandora and Stitcher, via SYNC AppLink™ (if applicable). • Access phonebook contacts and music via voice commands.
336 SYNC® GENERAL INFORMATION Make sure you review your device’s manual before using it with SYNC. Support The SYNC support team is available to help you with any questions you cannot answer on your own. Monday-Saturday, 8:30am-8:00pm EST In the United States, call: 1–888–270–1055 In Canada, call: 1–800–565–3673 Times are subject to change due to holidays. SYNC Owner Account Why do I need a SYNC owner account? • Required to activate Vehicle Health Report and to view the reports online.
SYNC® 337 Safety Information WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
338 SYNC® The cellular profile, media device index, and development log remain in the vehicle unless you delete them and are generally accessible only in the vehicle when the cellular phone or media player is connected. If you no longer plan to use the system or the vehicle, we recommend you perform a Master Reset to erase all stored information. System data cannot be accessed without special equipment and access to the vehicle’s SYNC module.
SYNC® Say: “Services” “Mobile apps” “Help” 339 If you want to: Access the SYNC Services portal.* Access mobile applications.* Hear a list of voice commands available in the current mode. * If equipped, U.S. only. System Interaction and Feedback The system provides feedback through audible tones, prompts, questions and spoken confirmations depending on the situation and the chosen level of interaction (voice settings).
340 SYNC® For example, “Say 1 after the tone to call John Doe at home. Say 2 after the tone to call Johnny Doe on mobile. Say 3 after the tone to call Jane Doe at home.” Or, “Say 1 after the tone to play John Doe, Say 2 after the tone to play Johnny Doe.” “Phone candidate lists on” “Phone candidate lists off” “Media candidate lists on” “Media candidate lists off” Helpful Hints • Make sure the interior of the vehicle is as quiet as possible.
SYNC® 341 Pairing a Phone for the First Time Note: Make sure the vehicle ignition and radio are turned on and the transmission is in position P (automatic transmission) or 1 (manual transmission). Wirelessly pairing your phone with SYNC allows you to make and receive hands-free calls. 1. Press the PHONE hard button; when the display indicates no phone is paired, press the Settings tab, then Add. 2. If Bluetooth is on, SYNC begins the pairing process between your Bluetooth-enabled phone or device and SYNC.
342 SYNC® Phone Voice Commands Press the voice button and say any of the following: “PHONE” “Call ” “Call at home” “Call at work” OR “Call in office” “Call on other” “Call on mobile OR cell” “Dial”* * If you have said “Dial”, see the “Dial” table below. “DIAL” “411” (four-one-one), “911” (nine-one-one), etc.
SYNC® 343 At any time, you can say the following global commands: GLOBAL COMMANDS “Exit” “Help” “Phone” “Services” * “Vehicle Health Report”* “Voice settings” * If equipped, U.S. only. Making Calls Using the Touchscreen Press the PHONE hard button, then choose between three ways to make a call: 1. Use the keypad on the Phone tab to manually enter a phone number and press SEND. 2. Select the Phonebook tab (if the desired number is saved in the downloaded phone book information).
344 SYNC® Receiving Calls When receiving a call, you can: • Answer the call by pressing the phone button. • Reject the call by pressing and holding the phone button. • Ignore the call by doing nothing. Phone Options during an Active Call During an active call, you have additional menu features which become available such as putting a call on hold, joining calls, etc. To access: 1. Press the PHONE hard button. 2.
SYNC® 345 Accessing Features through the Phone Menu SYNC’s phone menu allows you to redial a number, access your call history and phone book and send text messages as well as access phone and system settings. You can also access advanced features, such as 911 Assist™, Vehicle Health Report and SYNC Apps. 1. Press the PHONE hard button. 2.
346 SYNC® Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages. The system can also read incoming text messages to you so that you do not have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature. Your phone must support downloading text messages using Bluetooth to receive incoming text messages.
SYNC® 347 Sending Text Messages Text messaging is a phone-dependent feature. If your phone is compatible, SYNC allows you to receive, send, download and delete text messages. 1. Press the PHONE hard button. 2. Select the Text Messaging tab, then press Compose. 3. Scroll to select from the following options: Send Text Message? enables you to send a new text message based on a pre-defined set of 15 messages. 1. Press OK to select.
348 SYNC® Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you to access and adjust features such as your ring tone, text message notification, modify your phone book and also set up automatic download. 1. Press the phone button. 2. Scroll until Phone Settings appears, then press OK. 3.
SYNC® When you select: Modify Phonebook Auto Download Return 349 You can: Modify the contents of your phone book (i.e., add, delete, download). Press OK to select and scroll between: Add Contacts: Press OK to add more contacts from your phone book. Push the desired contact(s) on your phone. See your phone’s user guide on how to push contacts. Delete Phonebook: Press OK to delete the current phone book and call history. When Delete Phonebook appears, press OK to confirm.
350 SYNC® System Settings System Settings provide access to your Bluetooth Devices and Advanced menu features. The Bluetooth Devices menu allows you to add, connect, delete and set a phone as primary as well as turn your Bluetooth feature on and off. The Advanced menu allows you to access and set prompts, languages, defaults, perform a master reset, install an application and view system information.
SYNC® 351 If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off. Press OK and scroll to toggle between On and Off. When the desired selection is chosen, press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates all Bluetooth features. Delete a paired phone. Delete Device Press OK and scroll to select the device. Press OK to confirm. Delete all previously paired phones (and all Delete All Devices information originally saved with those phones).
352 SYNC® SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, U.S. only): Provides access to traffic, directions and information such as travel, horoscopes, stock prices and more. • 911 Assist®: Can alert 911 in the event of an emergency. • Vehicle Health Report (if equipped, U.S.
SYNC® 353 Note: If 911 Assist is turned on or off by any user, that setting applies for all paired phones. If 911 Assist is turned off, a voice message plays and/or a display message/icon comes on when the vehicle is started after a previously paired phone connects. Note: Every phone operates differently. While SYNC 911 Assist works with most cellular phones, some may have trouble using this feature.
354 SYNC® • A connected Bluetooth-enabled phone must have adequate network coverage, battery power and signal strength. • The vehicle must have battery power and be located in the U.S., Canada or in a territory in which 911 is the emergency number. In the Event of a Crash Not all crashes deploy an airbag or activate the fuel pump shut-off (which would activate 911 Assist); however, if 911 Assist is triggered, SYNC tries to contact emergency services.
SYNC® 355 Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannot replace normal maintenance and vehicle inspection. Vehicle Health Report only monitors certain systems that are electronically monitored by the vehicle and will not monitor or report the status of any other system, (i.e., brake lining wear).
356 SYNC® To run a report using the phone button and your vehicle is not equipped with a navigation system, 1. Press the phone button to enter the Phone Menu. 2. Scroll until Vehicle Health appears in the display, then press OK. 3. Select from one of the options listed in the following table. To run a report using the phone button and your vehicle is equipped with a navigation system: 1. Press the PHONE hard button. 2. Select the Settings tab. 3. Press Advanced, then select Vehicle Health Report. 4.
SYNC® 357 SYNC Services: Traffic, Directions & Information (TDI) Note: SYNC Services requires activation prior to use. Visit www.SYNCMyRide.com to register and check your eligibility for complimentary services. Standard phone and message rates may apply. Subscription may be required. You must also have the active SYNC Services Bluetooth-enabled cellular phone paired and connected to the system in order to connect to, and use, SYNC Services. See Using SYNC with your phone for pairing instructions.
358 SYNC® Connecting to SYNC Services Using Voice Commands 1. Press the voice button. 2. When prompted, say “Services”. This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabled cellular phone. 3. Once you are connected to the service, follow the voice prompts to request the desired service, such as “Traffic” or “Directions”. You can also say “What are my choices?” to receive a complete list of available services from which to choose. 4.
SYNC® 359 2. Follow the voice prompts to select your destination. Once your destination is selected, your current vehicle location is uploaded and a route based on current traffic conditions is calculated and sent back to your vehicle. After the route download is complete, the phone call is automatically ended. You then receive audible and visual driving instructions as you travel toward your destination. 3.
360 Portable SYNC® SYNC Services Quick Tips Your subscription is associated with your Bluetooth-enabled cellular phone number, not your VIN (Vehicle Identification Number). You can pair and connect your phone to any vehicle equipped with Traffic, Directions and Information and continue enjoying your personalized services. You can even access your account outside the vehicle. Just use the number on your phone’s call history.
SYNC® 361 To Access Using the Media Menu 1. Press the AUX button to access the SYNC menu. 2. Press the Menu button to access the SYNC Media menu. 3. Browse to Mobile Applications and press OK. 4. Browse to your desired app and press OK. 5. Once an app is running through SYNC, you can access an app’s menu by pressing the MENU button to first access the SYNC menu. 6. Scroll until “ Menu” is displayed (i.e., Pandora Menu), then press OK.
362 SYNC® Connecting Your Digital Media Player to the USB Port Note: If your digital media player has a power switch, make sure that the device is turned on. To connect using voice commands: 1. Plug the device into the vehicle’s USB port. 2. Press the voice icon and when prompted, say “User device”. 3. You can now play music by saying any of the appropriate voice commands, such as: • Play All • Play Artist • Play Album • Play Genre • Play Playlist • Play Track .
SYNC® 363 What’s Playing? At any time when a track is playing, you can press the voice icon and ask the system, “What’s playing?”. The system reads the metadata tags (if populated) of the playing track to you.
364 SYNC® Supported Media Players, Formats and Metadata Information SYNC® is capable of hosting nearly any digital media player, including iPod®, Zune™, Plays from device players, and most USB drives. Supported audio formats include MP3, WMA, WAV and AAC. You are also able to organize your indexed media from your playing device by metadata tags. Metadata tags are descriptive software identifiers embedded in the media files which provide information about the file.
SYNC® 365 Accessing the Media Music Library This menu allows you to select and play your media by artist, album, genre, playlist, track, similar music or even to explore what is on your USB device. 1. Make sure that your device is plugged into the USB port and is turned on. 2. Press the MEDIA hard button. 3. Select the User Device tab, then press Source repeatedly until USB appears. 4. Select Music Library. If there are no media files to access, the display indicates there is no media.
366 When you select: Playlists Tracks Explore USB SYNC® You can: Access your playlists (from formats, such as ASX, .M3U, .WPL, .MTP.). The system lists your playlists alphabetically in flat file mode. If there are more than 255, they are organized into alphabetical categories. Search for and play a specific track which has been indexed. SYNC lists your tracks alphabetically in flat file mode. If there are more than 255, SYNC automatically organizes them into alphabetical categories.
SYNC® 367 System Settings System settings provide access to your Bluetooth devices and Advanced menu features. The Bluetooth menu allows you to add, connect and delete a device as well as turn the Bluetooth feature on and off. The Advanced menu allows you to access and set prompts, languages, defaults and perform a master reset. Bluetooth Devices Menu Options This menu allows you to add, connect and delete devices as well as turn Bluetooth on and off. 1. Press the MEDIA hard button. 2.
368 SYNC® Phone Issues Possible Possible Solution(s) Cause(s) Excessive The audio control Review your phone’s user guide background noise settings on your regarding audio adjustments. during a phone phone may be call. affecting SYNC performance. During a call, I Possible phone Try turning off the device, malfunction. resetting the device, removing can hear the the device’s battery, then trying other person but they cannot hear again. me.
SYNC® 369 Phone Issues Possible Possible Solution(s) Cause(s) I am having • This is a • Go to the website to review trouble phone-dependent your phone’s compatibility. connecting my feature, OR • Try turning off the device, phone to SYNC. • Possible phone resetting the device or removing malfunction. the device’s battery, then trying again. • Try deleting your device from SYNC, deleting SYNC from your device and trying again.
370 SYNC® Issue I am having trouble connecting my device. SYNC does not recognize my device when I turn on the car. USB/Media Issues Possible Possible Solution(s) Cause(s) Possible device • Try turning off the device, malfunction. resetting the device or removing the device’s battery, then trying again. • Make sure you are using the manufacturer’s cable. • Make sure the USB cable is properly inserted into the device and the vehicle’s USB port.
SYNC® Issue Bluetooth audio does not stream. SYNC does not recognize music that is on my device. USB/Media Possible Cause(s) • This is a phone-dependent feature, OR • The device is not connected. • Your music files may not contain the proper artist, song title, album or genre information, OR • The file may be corrupted, OR • The song may have copyright protection which does not allow it to play.
372 SYNC® Vehicle Health Report/Services (Traffic, Directions and Information) Issues Issue Possible Possible Solution(s) Cause(s) I received a text • Your account • This is a free feature, but you that the Vehicle may not be must first register online to use Health Report is activated on the it. not activated. website, OR • Make sure that your VIN is correctly listed in your account. • You may have the wrong VIN (vehicle identification number) listed.
SYNC® 373 Vehicle Health Report/Services (Traffic, Directions and Information) Issues Issue Possible Possible Solution(s) Cause(s) I am unable to • This could be • Update your mobile number in your account on the website. submit a report. due to your • Make sure you have full signal phone’s compatibility, OR strength and that your Bluetooth volume level has been • Bad signal turned up. strength, OR • Try deleting your phone and • Your phone performing a clean pairing. may not be activated on the website.
374 SYNC® Voice Command Issues Possible Possible Solution(s) Cause(s) SYNC does not • You may be • Review the Phone voice understand what using the wrong commands and the Media voice I am saying. voice commands, commands at the beginning of their respective sections. OR • You may be • Be aware that SYNC’s speaking too soon microphone is either in your or at the wrong rear view mirror or in the time. headliner just above the windshield.
SYNC® Issue SYNC does not understand or is calling the wrong contact when I want to make a call. 375 Voice Command Issues Possible Possible Solution(s) Cause(s) • You may be • Review the phone voice commands at the beginning of using the wrong voice commands, the phone section. • Make sure you are saying the OR • You may not be contacts exactly as listed. For saying the name example, if a contact is saved as Joe Wilson, say “Call Joe exactly as it is Wilson”.
376 SYNC® Issue SYNC does not find any mobile apps that are on my phone. AppLink Issues Possible Possible Solution(s) Cause(s) • Your device • Check the website for may not support compatible devices and applications. the AppLink • Make sure your device is feature, OR • The application paired and connected. If you does not support have an iPhone®, make sure it is plugged in using the USB and AppLink., OR • If you have an that the application is running iPhone®, it may in the foreground.
Navigation System (If Equipped) 377 NAVIGATION CONTROLS Type 1 WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
378 Navigation System (If Equipped) E. TUNE RPT: • In radio or satellite radio mode, turn the control to advance in individual increments up or down the frequency band to the desired station. • In MP3 mode, turn the control to advance to the next or previous folder. • In navigation mode, press this button to hear the last spoken navigation guidance prompt. F. DISP: Press this button to select a display mode: On, Status Bar Only, and Off. G. SOUND: • Press this button to access the sound menu.
Navigation System (If Equipped) 379 M. MENU: • Press this button to access the system menu. • Press while the system menu is active to access the menu tabs of Display, Clock, Feedback Settings, System Settings and Valet Mode. N. MAP: • Press this button to access the navigation map. • Press while the map display is active to center the map on the current vehicle position. Press while the map display and route are active to see the different map guidance views. O.
380 Navigation System (If Equipped) Type 2 WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
Navigation System (If Equipped) 381 A. Memory presets: • Store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button until sound returns. • In radio and satellite radio mode, press a button to access your saved presets or channels. B. CD and DVD slot: Insert a CD or DVD, label side up. C. Eject: Press this button to eject a CD or DVD from the system. D.
382 Navigation System (If Equipped) L. MENU: • Press this button to access the system menu. • Press while the system menu is active to access the menu tabs of Display, Clock, Feedback Settings, System Settings and Valet Mode. M. SOUND: • Press this button to access the sound menu. • Press while the sound menu is active to access the menu tabs of Bass/Treble, Balance/Fade, SCV (Speed Compensated Volume), DSP (Digital Signal Processing) and Visualizer. N. MEDIA: • Press this button to access the media menu.
Navigation System (If Equipped) 383 Display mode voice commands “Night” “Auto” “Help” STATUS BARS The top status bar shows the current mode, exterior temperature, time and display icons if you have enabled Bluetooth or other options. The bottom status bar shows the Home icon and may also show the current driver and passenger selected temperatures, fan speed and air flow direction, the current mode being used, the Artist and Title of the currently playing CD, Artist and Title for Jukebox and radio.
384 Navigation System (If Equipped) Loading Photos Note: The system is not compatible with discs written in Packet Write mode. Your system allows you to upload and view up to 32 photos. Only the photograph(s), which meets the following conditions, display: • The file must be 1.5MB or smaller. • The file extension must be .jpe, .jpg or .jpeg. • The file path must be 255 characters or fewer. • Up to 256 files or folders can display in one folder. • The CD or DVD must be ISO 9660 format.
Navigation System (If Equipped) 385 Using the Touch-sensitive Controls on Your System To turn a feature on and off, just touch the graphic with your finger. To get the best performance from the touch-sensitive controls: • Make sure your hands are clean and dry. • Since the touchscreen operates based on the touch of a finger, you may have trouble using it if you are wearing gloves. • Use your bare finger to touch the center of a touch-control graphic.
386 Navigation System (If Equipped) How To Use Voice Commands with Your System Press the voice icon; after the tone, speak your command clearly. You can say these commands at any time. “Audio” “Navigation” “CD” “Radio” “Climate” “SYNC”* “Disc” “Tutorial” “Display mode” “User profile” “DVD” “Video CD” “Jukebox” “Voice settings” “Line in” “Help” * “Mobile apps” * See the SYNC chapter for more information on these features. To access a list of all available voice commands, press the I hard button.
Navigation System (If Equipped) 387 Voice Settings Voice settings allow you to customize the level of system interaction, help and feedback. The system defaults to standard interaction, which uses candidate lists, and confirmation prompts as these provide the highest level of guidance and feedback. Interaction Mode: Novice mode provides detailed interaction and guidance while the advanced mode has less audible interaction and more tone prompts.
388 Navigation System (If Equipped) If you select: Clock You can: Display Clock allows you to turn the clock on or off. Note: If your vehicle is equipped with an in-dash analog clock, you can set the time on this screen, but it may not appear in the status bar for viewing purposes. Format allows you to switch between 12– and 24–hour clock display. Auto Time Zone allows you to have the system automatically switch the time whenever you enter a new time zone.
Navigation System (If Equipped) If you select: Feedback 389 You can: Touch Screen Button Beep allows you to select when the system sounds an audible tone: All Buttons (whenever any system button is touched), Touch Screen (only when touchscreen selections are made) or Off (no audible tones at all). Voice Volume allows you to change navigation voice and audible tone volume by touching + or -. Satellite Radio Channel Name allows you to choose to display the satellite radio channel name.
390 Navigation System (If Equipped) If you select: System Settings Valet Mode Voice Control You can: Language allows you to choose between English, Spanish and French. Units allows you to choose between English and Metric measurements. Keyboard Layout allows you to choose between an ABC or QWERTY keyboard. Delete Stored Items allows you to choose to delete all of the entries from Address Book, Previous Destinations, Avoid Areas, Saved Photos and Voice Recognition Profiles.
Navigation System (If Equipped) 391 ENTERTAINMENT Your system offers many media options. You can access these options using the touchscreen or voice commands. AM/FM Radio Press the RADIO hard button. To change between AM, FM1 and FM2, touch the AM or FM tab. When you select: Show Options You can: Scan allows you to hear a brief sampling of all radio stations. Scan Presets allows you to hear a brief sampling of all stations stored in the memory presets.
392 Navigation System (If Equipped) When you select: Show Presets Set PTY/All You can: View the preset stations. Save a station by pressing and holding one of the memory preset areas. There is a brief mute while the radio saves the station. Sound returns when finished. Select a category of music you would like to search for and then choose to either seek or scan for the stations.** Note: The system scans the frequency band three times for the chosen program type.
Navigation System (If Equipped) 393 If you are listening to the radio, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to the radio, press the voice button and, after the tone, say “Radio”, then any of the commands in the following chart. * “<530–1710>” “<87.7–107.9>” “RADIO” “FM2” “FM2 preset <1–6>” “AM” “Off ” “AM <530–1710>” “On” “AM preset <1–6>” “FM <87.7–107.
394 Navigation System (If Equipped) HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Your system has a special receiver that allows it to receive digital broadcasts (where available) in addition to the analog broadcasts, it already receives. Digital broadcasts provide a better sound quality than analog broadcasts with free, crystal-clear audio and no static or distortion.
Navigation System (If Equipped) When you select: Tune Set PTY/All Multicast 395 You can: Go up and down the frequency in individual increments. If the current station has multiple digital broadcasts, the multicast indicator appears. Press Tune repeatedly to advance through all available broadcasts. If you are on the last broadcast channel, press to advance to the next frequency on the band. Select a category of music you would like to search for and then choose to either seek or scan for the stations.
396 Navigation System (If Equipped) When you select: To save a multicast station as a preset You can: When the channel is active on-screen, press and hold a memory preset slot until the sound returns. There is a brief mute while the radio saves the station. Sound returns when finished. When recalling a HD2 or HD3 memory preset, there is a mute before the digital audio plays, as the system must once again acquire the digital signal.
Navigation System (If Equipped) 397 In order to provide the best possible experience, use the contact form to report any station issues found while listening to a station broadcasting with HD Radio technology. Independent entities own and operate each station. These stations are responsible for ensuring all audio streams and data fields are accurate. Issue Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Sound fading or blending in and out.
398 Navigation System (If Equipped) Issue There is no text information shown for currently selected frequency. HD2-HD7 stations not found when Scan is pressed. Potential Station Issues Cause Action Data service issue by Fill out the station the radio broadcaster issue form at website listed below.* Pressing Scan disables No action required. HD2-HD7 channel This is normal search. behavior. * http://www.ibiquity.
Navigation System (If Equipped) 399 SIRIUS® Satellite Radio (If Activated) Press the RADIO hard button, then select SAT on the touchscreen. When you select: SAT123 Scan Scan Presets Channel Guide Direct Tune Set Genre You can: Press this button to access three different satellite radio modes (SAT1, SAT2 or SAT3). Press this button to hear a brief sampling of all satellite radio channels within the current genre. Press these buttons to hear a brief sampling of all channels stored in the memory presets.
400 Navigation System (If Equipped) When you select: Memo Show Presets You can: Press this button to save a song title and artist to the system. When the saved song is playing on any satellite radio channel, the system alerts you with a pop-up in the lower status bar. You can either tune to the station or ignore the pop-up. When you are in the Memo screen, the following options are available: Refresh allows you to refresh the current artist and title information.
Navigation System (If Equipped) 401 SIRIUS® Satellite Radio Voice Commands If you are listening to SIRIUS satellite radio, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to SIRIUS satellite radio, press the voice button and, after the tone, say “Sirius”, then any of the commands in the following chart.
402 Navigation System (If Equipped) SIRIUS® Information Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Navigation System (If Equipped) 403 Potential reception issues When you pass a ground-based broadcast-repeating tower, a stronger signal may overtake a weaker one and the audio system may mute. Satellite radio signal Your display may show ACQUIRING... to interference indicate the interference and the audio system may mute. Station overload Radio Display Acquiring...
404 Navigation System (If Equipped) Radio Display Updating. Troubleshooting tips Condition Update of channel programming in progress. Your satellite service is no longer available. Possible Action No action required. The process may take up to three minutes. Call SIRIUS Contact SIRIUS at 1–888–539–7474. 1-888-539-7474 to resolve subscription issues. No Channels Available.
Navigation System (If Equipped) 405 CD Voice Commands If you are listening to a CD, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to a CD, press the voice button and, after the tone, say “CD”, then any of the commands in the following chart.
406 Navigation System (If Equipped) DVD Note: Your system only plays NTSC formatted discs. The system does not support PAL format. Your system allows you to play DVD audio and video discs. Make sure your vehicle is in position P (vehicles equipped with an automatic transmission) or the parking brake is engaged (vehicles equipped with a manual transmission). This allows you to be able to view and hear the DVD. If your vehicle is moving, the video does not play.
Navigation System (If Equipped) 407 During disc play, you can also touch the screen to access the virtual remote, which allows you to Move Controls on the screen, as well as use the cursor controls, Enter and Return to navigate and select within the menus. Dolby® noise reduction is manufactured under license from Dolby® Laboratories Licensing Corporation. Dolby® and the double-D symbol are registered trademarks of Dolby® Laboratories Licensing Corporation.
408 Navigation System (If Equipped) DVD Voice Commands If you are watching a DVD, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not watching a DVD, press the voice button and, after the tone, say “DVD”, then any of the commands in the following chart.
Navigation System (If Equipped) 409 Jukebox Your system has a Jukebox feature, which allows you to save desired tracks or CDs to the hard drive for later access. The hard drive can store up to 10 GB* (164 hours; approximately 2472 tracks) of music. The system contains a Gracenote® media database that allows for display of song title, album title, and album cover art. After saving music to the hard drive, you can access and play your music by specific tracks, artists, albums or genres.
410 Navigation System (If Equipped) When you select: Music library Options You can: Access all of your saved music. You can choose to view or play the material in the following ways: Play All Tracks allows you to play all tracks saved in the jukebox. Playlist allows you to play your own playlist. Play genre allows you to have the system play only music from a specific genre. Play artist allows you to have the system play only music by a specific artist.
Navigation System (If Equipped) 411 Creating a Playlist Press the MEDIA hard button, and then select the Jukebox tab on the touchscreen. 1. Select Options. 2. Select Edit Playlists, then which playlist you would like to create. 3. Select which category you would like to access from your saved music. 4. Select the desired songs and then press Add. The system shows you the currently selected songs.
412 Navigation System (If Equipped) User Device If your vehicle is equipped with SYNC®, there is a User Device tab. For more information, see the SYNC® chapter. Line In (Auxiliary Input Jack) Your vehicle is equipped with an audio input jack, which allows you to plug a portable audio device into your vehicle’s audio system. To turn this feature on, press the MEDIA hard button on the system. For more information on the auxiliary input jack, see Auxiliary input jack in the Audio Systems chapter.
Navigation System (If Equipped) Fan speed Passenger temperature Dual MAX A/C 413 Climate Control Features Touch + or – to increase or decrease fan speed. Touch the arrows to increase or decrease the temperature. Touch to turn on the passenger temperature control. Touch to cool your vehicle with recirculated air. Touch again for normal A/C operation. MAX A/C is more economical and efficient than normal A/C mode.
414 Navigation System (If Equipped) INFORMATION Under the Information menu, you can access features such as Where Am I? and SIRIUS® Travel Link™, view your calendar, see system information and get basic system help. Press the I (Information) hard button to access these features. Where Am I? Press the I button and select the Where Am I? tab.
Navigation System (If Equipped) 415 Press the I (information) button, then select Sirius Travel Link. Choose from any of the following services: When you select: Traffic On Route Traffic Nearby My Places Weather You can: Identify traffic incidents on your route, nearby your vehicle’s current location or near any of your favorite places (if programmed). View the nearby weather, current weather, or the 5–day forecast for the chosen area.
416 Navigation System (If Equipped) “TRAVEL LINK” “Fuel prices” “Sports scores”** “Golf leaders” “Traffic” “Golf schedule” “Travel link help” “Motor sports order” “Weather” “Motor sports schedule” “Weather map” “Movie listings” * If you have said, “Sports schedule”, you may say any of the commands in the “Sports schedule” chart: ** If you have said, “Sports scores”, you may say any of the commands in the “Sports scores” chart: “SPORTS SCHEDULES” “Baseball schedule” “NBA schedule” “College basketball sch
Navigation System (If Equipped) 417 System Information Press the I (information) button, then select System Information. In this screen, you can view the following options: • Phone number for your Customer Service Center • Current system versions installed • Current SIRIUS® Radio ESN • SIRIUS® Travel Link™ ESN. Note: Not all tab selections may be available in all markets. Check with your authorized dealer for availability.
418 Navigation System (If Equipped) SOUND The sound menu allows you to access and adjust settings, such as Bass, Treble, Fade, Balance, Speed Compensated Volume (SCV) and the visualizer. Press the SOUND hard button. When you select: Bass/Treble Balance/Fade SCV Visualizer You can: Increase or decrease levels by pressing + or -. Adjust the sound between the left and right speakers and front and rear speakers.
Navigation System (If Equipped) 419 Route Guidance in Incompletely Mapped Areas There are some rural areas in the map database without fully verified roads.
420 Navigation System (If Equipped) Quick Note: Items on this screen are selectable at any speed. Find Nearest POI Select up to five different points of interest (POI) favorites that you can search for while your vehicle is moving. You can change these categories at any time but the default categories are: • Gas Station • ATM • Restaurant • Accommodations • Parking Garage When you select a category, the system displays a list in order of distance from your vehicle’s location.
Navigation System (If Equipped) 421 Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Address Book You can store up to 25 entries, which you can use as destinations, waypoints and areas to avoid. You can sort the entries alphabetically, by date or icon.* Previous You can store up to 20 recently used Destination destinations and waypoints. Duplicate entries do not appear in the list.
422 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Street Address Touch this button to program a street address as a destination or waypoint. • State/Prov lets you use the keyboard to type or you can select the area to search from a list. The system bases the search on your vehicle’s current position or the previous selection.
Navigation System (If Equipped) 423 Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Point of Interest Touch this button to select a point of interest (POI) on the map as a destination or waypoint. There are three ways to search for a point of interest: 1. Enter a city name in the City field and a point of interest in the Name field. 2.
424 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Freeway Touch this button to select an entrance and Entrance/Exit exit point to a freeway you select. You can sort the entrance and exit point alphabetically or in order of distance from your vehicle’s position. You can then select the point you choose as a destination or waypoint.
Navigation System (If Equipped) 425 Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Intersection Touch this button to select an intersection point. Enter the name of the first street, then the first letter of the second street. The system displays possible intersection matches based on the first letter of the second street.
426 Navigation System (If Equipped) * To delete all stored Address Book and Previous Destination entries at once: 1. Press the MENU hard button. 2. Select the System Settings tab. 3. Press the View button for Delete Stored Items. 4. Select Address Book or Previous Destinations. Cancel Route Detour View Route Edit Route Preferences Edit Route Touch this button to cancel the current route. Touch this button to avoid an area on the current route. Touch this button to view the entire current route.
Navigation System (If Equipped) 427 Programming a Destination Using Voice Commands Press the voice button on the steering wheel. If you want to: Enter an address. Enter an intersection. Find a point of interest (POI) by its category. Find a point of interest (POI) by its name. Go to a previous destination. Go to your home location. Use a nametag from your address book. Get help.
428 Navigation System (If Equipped) Route Selection Screen Icons Icons, located above the route selection choices, represent features on the routes. A. Freeways A B C B. Toll Roads C. Ferries D. High-occupancy Vehicle Lanes E. Time-restricted Roads F. Avoid Area Selection F E D If you select the fastest route, and the freeways icon is illuminated, this means that the route uses freeways.
Navigation System (If Equipped) 429 Within these main categories, there are subcategories, which contain more listings: Subcategories Restaurant Auto Dealership Parking Public Transit Home & Garden Education Personal Care Services Setting Your Navigation Preferences Select settings for the system to take into account when planning your route. Press the NAV hard button. Map Content Map View Map Preferences Street Name displays current street name during route guidance.
430 Navigation System (If Equipped) Bird’s Eye View Turn List Format Shortest Distance Fastest Time Avoid Freeways Avoid Tollroads Avoid Ferries Avoid HOV Lanes Avoid Time Restricted Roads Map Preferences ON provides an elevated map perspective. OFF turns the feature off. Adjust Angle offers six different map angles. Top-to-Bottom starts the turn instructions from the top. Bottom-to-Top starts the turn instructions from the bottom. Route Preferences Have the system display the shortest route first.
Navigation System (If Equipped) 431 Traffic Preferences* Traffic Icons to Touch this button to display a list of map overlay on Map icons that you can turn off and on. The list of icons includes: • Weather related incidents • Road work • Incident • Accident • Closed road Traffic Flow Overlay Touch this button to have the map show traffic flow coloring on major roads. Roads display in green (all clear), yellow (reduced speed) and red (stopped).
432 Navigation System (If Equipped) Navigation Preferences When this feature is on, the system displays the average speed on a residential road, initially set to 25 mph (40 km/h). You can change the setting for your driving preferences. This setting helps estimate your arrival time at a destination based on your driving preferences. Avg. Speed: Main When this feature is on, the system displays Roads the average speed on a main road, initially set to 45 mph (72 km/h).
Navigation System (If Equipped) Calibrate Restore Default Settings 433 Navigation Preferences Position allows you to adjust the direction of your vehicle by pressing the arrow buttons on the screen. Distance allows you to recalibrate the distance to the destination while your vehicle is moving. Touch the Reset button to return the settings to factory defaults. * This feature requires activation of SIRIUS® Travel Link™, which is only available in the United States.
434 Navigation System (If Equipped) North Up always shows the northern direction to be upward on the screen. Map Icons Vehicle mark shows the current location of your vehicle. It stays in the center of the map display, except when in scroll mode. Scroll cursor allows you to scroll the map; the fixed icon is in the center of the screen. The map position closest to the cursor is in a window on the top center part of the screen.
Navigation System (If Equipped) 435 No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map positioning. This icon may display under normal operation in an area with poor GPS access. Map Scale The map display scale has 17 levels, ranging from 0.02 miles (.03 kilometers) to 1000 miles (1600 kilometers). The system synchronizes the zoom scales for North Up, 0.1 mi Heading Up and 3D Map views.
436 Navigation System (If Equipped) Quick-touch Buttons When in map mode, touch anywhere on the map display to access the following options: When you select: Set as Dest Set as Waypoint Save to Address Book POI Icons On/Off You can: Select a scrolled location on the map as your destination. You may scroll the map by pressing your index finger on the map display. When you reach the desired location, simply let go and then press Set as Dest. Set the current location as a waypoint.
Navigation System (If Equipped) 437 Navigation Voice Commands When in navigation mode, press the voice button on the steering wheel control.
438 Navigation System (If Equipped) “DESTINATION” “Street address” “Help” Troubleshooting Symptoms Focus error. Bad disc. Track error. Invalid disc detected. A pop-up window displays “Address not found” or “Address range does not exist. Show the midpoint of the street?” Possible Cause The system is not able to play a reproduced disc. You inserted the disc upside down or the system is unable to read the information on the disc. The system is unable to reproduce a corrupt MP3 file.
Navigation System (If Equipped) Symptoms A pop-up window displays “Navigation fault. A system fault has been detected that may cause the navigation to perform abnormally. Please contact your dealership.” A pop-up window displays “Error. PINs did not match. Please re-enter.” A pop-up window displays “Invalid PIN. Please Re-enter.” Possible Cause There is a system hardware or software error. 439 Action Contact your authorized dealer.
440 Appendices GENERAL INFORMATION SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMPANY from an affiliate of Microsoft Corporation (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“MS SOFTWARE”) are protected by international intellectual property laws and treaties. The MS SOFTWARE is licensed, not sold. All rights reserved.
Appendices 441 DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS: • Speech Recognition: If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process. Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
442 Appendices • Security Updates/Digital Rights Management: Content owners use the WMDRM technology included in your DEVICE to protect their intellectual property, included copyrighted content. Portions of the SOFTWARE on your DEVICE use WMDRM software to access WMDRM-protected content. If the WMDRM software fails to protect the content, content owners may ask Microsoft to revoke the SOFTWARE’s ability to use WMDRM to play or copy protected content. This action does not affect unprotected content.
Appendices 443 If FORD MOTOR COMPANY or third party software and services suppliers provide or make available to you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of this EULA shall apply.
444 Appendices INTELLECTUAL PROPERTY RIGHTS: All title and intellectual property rights in and to the SOFTWARE (including but not limited to any images, photographs, animations, video, audio, music, text and “applets,” incorporated into the SOFTWARE), the accompanying printed materials, and any copies of the SOFTWARE, are owned by MS, Microsoft Corporation, FORD MOTOR COMPANY, or their affiliates or suppliers. The SOFTWARE is licensed, not sold.
Appendices 445 No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LAW, FORD MOTOR COMPANY, ANY THRID PARTY SOFTWARE OR SERVICES SUPPLIERS, MS, MICROSOFT CORPORATION AND THEIR AFFILIATES SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE.
446 Appendices WARNING: Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences. Do not change system settings or enter data non-verbally (using your hands) while driving. Stop the vehicle in a safe and legal manner before attempting these operations.
Appendices 447 Distraction Hazard Any navigation features may require manual (non-verbal) setup. Attempting to perform such set-up or insert data while driving can seriously distract your attention and could cause an accident or other serious consequences. Stop the vehicle in a safe and legal manner before attempting these operations. Let Your Judgment Prevail Any navigation features are provided only as an aid.
448 Appendices Map Data DVD End User License Terms The data (“Data”) is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms and conditions which are agreed to by you, on the one hand, and (Licensee). (“Licensee”) and its licensors (including their licensors and suppliers) on the other hand. Such licensors include NAVTEQ North America, LLC.
Appendices 449 Disclaimer of warranty:(Licensee) and its licensors (including their licensors and suppliers) disclaim any warranties, express or implied, of quality, performance, merchantability, fitness for a particular purpose or non infringement. Some States, Territories and Countries do not allow certain warranty exclusions, so to that extent the above exclusion may not apply to you.
450 Appendices Governing law: The above terms and conditions shall be governed by the laws of the Illinois, without giving effect to (i) its conflict of laws provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is explicitly excluded. You agree to submit to the jurisdiction of Illinois for any and all disputes, claims and actions arising from or in connection with the Data provided to you hereunder.
Appendices 451 Gracenote® End User License Agreement (EULA) This device contains software from Gracenote, Inc. of 2000 Powell Street Emeryville, California 94608 (“Gracenote”). The software from Gracenote (the “Gracenote Software”) enables this device to do disc and music file identification and obtain music-related information, including name, artist, track, and title information (“Gracenote Data”) from online servers (“Gracenote Servers”), and to perform other functions.
452 Appendices THE GRACENOTE SOFTWARE, EACH ITEM OF GRACENOTE DATA AND THE GRACENOTE CONTENT ARE LICENSED TO YOU “AS IS.” NEITHER GRACENOTE MAKES ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, REGARDING THE ACCURACY OF ANY GRACENOTE DATA FROM THE GRACENOTE SERVERS OR GRACENOTE CONTENT.
Index 911 Assist™ ..............................352 A ABS (see Brakes) .....................179 Accessing call history/phone book during active call .............344 Accessing the help screen .......417 Accessing the music in your jukebox ......................................409 Accessing your media menu features ......................................364 Accessing your phone menu features ......................................345 Accessory delay ..........................87 Active call menu options .......
454 Index fluid, refill capacities ..............306 fluid, specifications .................306 lubricant specifications ..........306 parking ....................................180 shift interlock ..........................171 trailer .......................................203 C Capacities for refilling fluids ....306 CD ..............................................122 CD player ..................................120 CD voice commands .................405, 407–408 Cell phone use ........................
Index D Defrost ...............................131, 133 rear window ............................136 Dipstick automatic transmission fluid ..........................................248 engine oil .................................242 Driving under special conditions ..................................172 through water .........................213 Dual automatic temperature control (DATC) .........................133 E Electronic message center .........99 Electronic stability control ......
456 Index odometer .................................110 trip odometer ..........................110 Jukebox features .......................409 Jump-starting your vehicle ......218 H K Hazard flashers .........................217 HD Radio™ ...............................394 Headlamps aiming ..............................253–254 bulb specifications ..................259 flash to pass ..............................80 high beam .................................80 Head restraints .........................
Index Media Bluetooth menu options (adding, connecting, deleting, turning on/off) ..........................367 Message center ...........................99 display color ............................104 english/metric button .............104 MyColor display ......................104 system check button ..............104 warning messages ...........104, 114 Mirrors ...................................87, 89 side view mirrors (power) .......87 Motorcraft® parts .............260, 310 MyKey .....................
458 Index opening the trunk .....................66 replacing the batteries .............56 Reverse sensing system ...........186 Roadside assistance ..................216 SecuriLock passive anti-theft system ..........................................70 S Selecting your media source (USB, Line in, BT audio) .........364 Safety Belt Maintenance ............42 Safety belts (see Safety restraints) ....................................35 Safety defects, reporting ..........229 Safety information ..........
Index T Temperature control (see Climate control) .......131, 133 Temporary mobility kit .............295 Text messaging .........................346 Text messaging (sending, downloading, deleting) .....347–348 Tilt steering wheel ......................75 Tires ...................................269, 289 alignment ................................282 care ..........................................269 changing ..........................289, 291 checking the pressure ............278 inflating .................
460 Index W Warning lights (see Lights) .......94 Washer fluid ..............................249 Water, Driving through .............213 Where am I? ..............................414 Windows power .........................................85 Windshield washer fluid and wipers ..........................................78 checking and adding fluid .....249 replacing wiper blades ...........252 Wrecker towing .........................
