2015 EDGE Owner’s Manual 2015 EDGE Owner’s Manual fordowner.com ford.ca December 2014 First Printing Owner’s Manual Edge Litho in U.S.A.
The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2014 All rights reserved.
Table of Contents Driver and Passenger Airbags...................39 Front Passenger Sensing System............40 Side Airbags.....................................................42 Driver and Passenger Knee Airbags........43 Safety Canopy™............................................44 Crash Sensors and Airbag Indicator.......45 Airbag Disposal..............................................46 Introduction About This Manual...........................................7 Symbols Glossary..........................
Table of Contents Audio Control...................................................75 Audio Control...................................................76 Voice Control....................................................76 Cruise Control..................................................76 Information Display Control........................77 Heated Steering Wheel................................77 Information Displays General Information...................................100 Information Messages...............
Table of Contents Overhead Console.......................................149 Stability Control Principle of Operation..................................181 Using Stability Control................................182 Starting and Stopping the Engine General Information....................................150 Ignition Switch...............................................150 Keyless Starting - Vehicles With: Push Button Start...............................................150 Starting a Gasoline Engine..........
Table of Contents Towing the Vehicle on Four Wheels 6-Speed Automatic Transmission 6F35...............................................................231 Towing the Vehicle on Four Wheels 6-Speed Automatic Transmission 6F50/6F55.................................................232 Maintenance General Information...................................258 Opening and Closing the Hood..............258 Under Hood Overview - 2.0L EcoBoost™................................................259 Under Hood Overview - 2.
Table of Contents Cleaning the Instrument Panel and Instrument Cluster Lens........................281 Cleaning Leather Seats.............................282 Repairing Minor Paint Damage..............283 Cleaning the Alloy Wheels.......................283 Vehicle Storage............................................283 Audio Unit - Vehicles With: Premium AM/ FM/CD.........................................................343 Audio Unit - Vehicles With: Sony AM/FM/ CD............................................
Table of Contents Scheduled Maintenance Record...........463 Appendices End User License Agreement...................471 Type Approvals............................................
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it. WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Introduction Brake system Fasten safety belt Cabin air filter Front airbag Check fuel cap Front fog lamps Child safety door lock or unlock Fuel pump reset Child seat lower anchor Fuse compartment Child seat tether anchor Hazard warning flashers Cruise control Heated rear window Do not open when hot Heated windshield Engine air filter Interior luggage compartment release Engine coolant Jack Engine coolant temperature Keep out of reach of children E71340 E161353 Engine oil Lighting co
Introduction systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access or share among them vehicle diagnostic information received through a direct connection to your vehicle when diagnosing or servicing your vehicle. Additionally, when your vehicle is in for service or repair, Ford Motor Company, Ford of Canada, and service and repair facilities may access or share among them data for vehicle improvement purposes.
Introduction • • How fast the vehicle was traveling; and Where the driver was positioning the steering wheel.
Introduction REPLACEMENT PARTS RECOMMENDATION CALIFORNIA PROPOSITION 65 WARNING Your vehicle has been built to the highest standards using quality parts. We recommend that you demand the use of genuine Ford and Motorcraft parts whenever your vehicle requires scheduled maintenance or repair. You can clearly identify genuine Ford and Motorcraft parts by looking for the Ford, FoMoCo or Motorcraft branding on the parts or their packaging.
Introduction Warranty on Replacement Parts remote insurance company monitoring, remote vehicle diagnostics, telematics or engine reprogramming, may cause interference or damage to vehicle systems. We do not recommend or endorse the use of any non-Ford-approved aftermarket OBD plug-in devices. The vehicle Warranty may not cover damage caused by any non-Ford-approved aftermarket OBD plug-in device.
Introduction EXPORT UNIQUE OPTIONS For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this Owner’s Manual. A market unique supplement may be supplied that complements this book. By referring to the market unique supplement, if provided, you can properly identify those features, recommendations and specifications that are unique to your vehicle. This Owner’s Manual is written primarily for the U.S.
Environment PROTECTING THE ENVIRONMENT You must play your part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim.
Child Safety GENERAL INFORMATION WARNINGS is compatible with and properly installed in your vehicle. To locate a child seat fitting station and CPST, contact the NHTSA toll free at 1-888-327-4236 or go to http://www.nhtsa.dot.gov. In Canada, check with your local St. John Ambulance office for referral to a CPST or for further information, contact your provincial ministry of transportation, locate your local St. John Ambulance office by searching for St.
Child Safety Recommendations for Safety Restraints for Children Child Child size, height, weight, or age Recommended restraint type Infants or toddlers Children weighing 40 lb (18 kg) or less (generally age four or younger). Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat). Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 ft. 9 in. (1.
Child Safety • Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers, or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). • Using Lap and Shoulder Belts Place the vehicle seat upon which the child seat will be installed in the upright position. Put the safety belt in the automatic locking mode. See Step 5. This vehicle does not require the use of a locking clip.
Child Safety 2. After positioning the child safety seat in the proper seating position, pull down on the shoulder belt and then grasp the shoulder belt and lap belt together behind the belt tongue. E142875 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. Note: The automatic locking mode is available on the front passenger and rear seats. E142530 3.
Child Safety 8. Remove remaining slack from the belt. Force the seat down with extra weight, for example, by pressing down or kneeling on the child restraint while pulling up on the shoulder belt in order to force slack from the belt. This is necessary to remove the remaining slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle.
Child Safety Note: Unlike the standard safety belt, the inflatable safety belt's unique lap portion locks the child seat for installation. The ability for the shoulder portion of the belt to move freely is normal, even after the lap belt has been put into the automatic locking mode. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted.
Child Safety Using Lower Anchors and Tethers for CHildren (LATCH) slack that will exist once the extra weight of the child is added to the child restraint. It also helps to achieve the proper snugness of the child seat to your vehicle. Sometimes, a slight lean toward the buckle will additionally help to remove remaining slack from the belt. 9. Attach the tether strap (if the child seat is equipped). WARNINGS Never attach two child safety seats to the same anchor.
Child Safety Use of Inboard Lower Anchors from the Outboard Seating Positions (Center Seating Use) WARNING The standardized spacing for LATCH lower anchors is 11 inches (28 centimeters) center to center. Do not use LATCH lower anchors for the center seating position unless the child seat manufacturer's instructions permit and specify using anchors spaced at least as far apart as those in this vehicle.
Child Safety Combining Safety Belt and LATCH Lower Anchors for Attaching Child Safety Seats Perform the following steps to install a child safety seat with tether anchors: Note: If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off your vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Child Safety recommended by your child restraint manufacturer). Many state and provincial laws require that children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.45 meters) tall, or 80 pounds (36 kilograms). Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat: E142539 3. Clip the tether strap to the anchor as shown. 4.
Child Safety Types of Booster Seats E70710 • E68924 • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child's head (as measured at the tops of the ears) above the top of the seat.
Child Safety E142597 WARNINGS warnings provided by your vehicle manufacturer. A safety seat that is improperly installed or utilized, is inappropriate for your child's height, age, or weight or does not properly fit the child may increase the risk of serious injury or death. If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Child Safety Recommendations for attaching child safety restraints for children Use any attachment method as indicated below by X Restraint Type Combined weight of child and child seat LATCH (lower anchors and top tether anchor) LATCH (lower anchors only) Rear facing Up to 65 lb child seat (29.5 kg) Safety belt Safety belt Safety belt and LATCH only and top (lower tether anchors anchor and top tether anchor) X X Rear facing Over 65 lb child seat (29.
Child Safety Left-Hand Side Turn counterclockwise to lock and clockwise to unlock. Right-Hand Side Turn clockwise to lock and counterclockwise to unlock.
Safety Belts PRINCIPLE OF OPERATION WARNINGS When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. WARNINGS Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child.
Safety Belts • Crash sensors and monitoring system with readiness indicator. The safety belt pretensioners at the front seating positions are designed to tighten the safety belts when activated. In frontal and near-frontal crashes, the safety belt pretensioners may be activated alone or, if the crash is of sufficient severity, together with the front airbags. The pretensioners may also activate when a Safety Canopy airbag is deployed. E142588 FASTENING THE SAFETY BELTS 2.
Safety Belts Using Safety Belts During Pregnancy WARNINGS Belt and retractor assembly must be replaced if the safety belt assembly automatic locking retractor feature or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in crashes. WARNING Always ride and drive with your seatback upright and the safety belt properly fastened.
Safety Belts When to Use the Automatic Locking Mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children 12 years old and under should be properly restrained in a rear seating position whenever possible. See Child Safety (page 15). How to Use the Automatic Locking Mode E146363 Non-inflatable safety belts 1. Buckle the combination lap and shoulder belt. 2.
Safety Belts Note: The rear inflatable safety belts are compatible with most infant and child safety car seats and belt positioning booster seats when properly installed. This is because they are designed to fill with a cooled gas at a lower pressure and at a slower rate than traditional airbags. After inflation, the shoulder portion of the safety belt remains cool to the touch. The rear inflatable safety belt consists of the following: • An inflatable bag located in the shoulder safety belt webbing.
Safety Belts If the safety belt is too short when fully extended, a safety belt extension assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is on a label located either at the end of the webbing or on the retractor behind the trim. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.
Safety Belts The system uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid the system turning on the Belt-Minder feature for objects you place on the front passenger seat, only the front seat passengers receive warnings as determined by the front passenger sensing system.
Safety Belts Deactivating and Activating the Belt-Minder Feature 4. While the safety belt warning light is on, buckle and then unbuckle the safety belt. After Step 4, the safety belt warning light flashes for confirmation. • This will switch the feature off for that seating position if it is currently on. • This will switch the feature on for that seating position if it is currently off.
Personal Safety System™ How Does the Personal Safety System Work? The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Supplementary Restraints System The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. PRINCIPLE OF OPERATION WARNINGS Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module.
Supplementary Restraints System Proper Driver and Front Passenger Seating Adjustment DRIVER AND PASSENGER AIRBAGS WARNING WARNINGS Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Supplementary Restraints System This system works with sensors that are part of the front passenger’s seat and safety belt to detect the presence of a properly-seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or not. E142846 Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Supplementary Restraints System • • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the passenger airbag status indicator will illuminate the OFF lamp and stay lit to remind you that the front passenger frontal airbag is disabled.
Supplementary Restraints System If there are lodged objects, or cargo is interfering with the seat, take the following steps to remove the obstruction: feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.
Supplementary Restraints System The system consists of the following: • A label or embossed side panel indicating that side airbags are fitted to your vehicle. • Side airbags located inside the driver and front passenger seatbacks. • Front passenger sensing system. WARNINGS Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. Do not lean your head on the door.
Supplementary Restraints System severity and occupant conditions. Under certain crash and occupant conditions, the driver and passenger knee airbag may deploy but the driver front airbag may not activate. As with front and side airbags, it is important to be properly seated and restrained to reduce the risk of death or serious injury. WARNINGS If the curtain airbags have deployed, the curtain airbags will not function again.
Supplementary Restraints System airbag, knee airbag(s), seat mounted side airbags, the Safety Canopy and optional rear inflatable safety belts. Based on the type of crash (frontal impact or side impact), the restraints control module will deploy the appropriate safety devices. · Crash sensors and monitoring system with a readiness indicator. See Crash Sensors and Airbag Indicator (page 45). Children 12 years old and under should always be properly restrained in the rear seats.
Supplementary Restraints System The fact that the safety belt pretensioners or front airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (crash severity, belt usage) were not appropriate to activate these safety devices.
Keys and Remote Controls Intelligent Access (If Equipped) GENERAL INFORMATION ON RADIO FREQUENCIES The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met: • You activate the front exterior door handle switch. • You press the luggage compartment button. • You press a button on the transmitter. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Keys and Remote Controls E151795 Note: The keys that came with your vehicle have a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference. E151796 Slide the release on the back of the remote control and pivot the cover off to access the key blade. Intelligent Access Key (If Equipped) E151795 Note: The backup keys that came with your vehicle have a security tag that provides important vehicle key cut information.
Keys and Remote Controls Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally. A message appears in the information display when the remote control battery is low. See Information Messages (page 109).
Keys and Remote Controls 6. Install a new battery with the + facing up. 7. Replace the battery cover. Intelligent Access Transmitter The remote control uses two coin-type three-volt lithium batteries CR2025 or equivalent. E151799 3. Carefully remove the cover. E151796 1. Slide the release on the back of the remote control and pivot the cover off. Note: Do not touch the battery contacts or the printed circuit board with the screwdriver. 4. Insert a screwdriver as shown to release the battery.
Keys and Remote Controls Note: Do not use remote start if your vehicle is low on fuel. The remote start button is on the transmitter. E138625 This feature allows you to start your vehicle from outside the vehicle. The transmitter has an extended operating range. If your vehicle has automatic climate control, you can configure it to operate when you remote start your vehicle. See Climate Control (page 124). See Information Displays (page 100).
Keys and Remote Controls LED Status Solid green. Remote start or extension successful. Solid red. Remote stop successful; vehicle off. Blinking red. Remote start or stop failed. Blinking green. Waiting for status update. Note: If you remote start the vehicle with an integrated keyhead transmitter, you must switch the ignition on before driving your vehicle.
Keys and Remote Controls Memory Feature If programmed to a pre-set position, the integrated keyhead transmitter or intelligent access key recalls the driver seat and exterior mirror positions when you unlock your vehicle. It also recalls the power steering column and pedal positions. See Memory Function (page 137). REPLACING A LOST KEY OR REMOTE CONTROL Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle.
MyKey™ Non-configurable Settings PRINCIPLE OF OPERATION The following settings cannot be changed by an admin key user: • Safety belt reminder. You cannot disable this feature. The audio system will mute when the front seat passengers’ safety belts are not fastened. • Early low fuel or charge. The low-fuel or low charge warning activates earlier, giving the MyKey user more time to refuel or recharge.
MyKey™ • • • MyKey is successfully created. Make sure you label it so you can distinguish it from the admin keys. Various vehicle speed minders can be set. Once you select a speed, it will be shown in the display, followed by an audible tone when the preselected vehicle speed is exceeded. Audio system maximum volume of 45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled.
MyKey™ To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scroll to: Message Action and Description Settings Press the OK button. MyKey Press the OK button. Clear MyKey Press and hold the OK button until the following message displays. All MyKeys Cleared Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.
MyKey™ You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 100). CHECKING MYKEY SYSTEM STATUS To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll to: Message Description Settings Press the OK button. MyKey Press the OK button. Select one of the following: MyKey Dist. Tracks the distance when drivers use a MyKey.
MyKey™ Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system. USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non MYKEY TROUBLESHOOTING Condition I cannot create a MyKey. Potential Causes • • • • I cannot program the configurable settings. • • I cannot clear the MyKeys. • • I lost the only admin key.
MyKey™ Condition Potential Causes I lost a key. Program a spare key. See Passive Anti-Theft System (page 71). MyKey distances do not accumulate. • • • No MyKey functions with the keyless entry transmitter. • • The MyKey user is not using the MyKey. An admin key holder cleared the MyKeys and created new MyKeys. The key system has been reset. An admin transmitter is present at vehicle start. No MyKeys are created. See Creating a MyKey (page 55).
Locks LOCKING AND UNLOCKING Remote Control You can use the power door lock control or the remote control to lock and unlock your vehicle. You can use the remote control at any time. The luggage compartment release button only operates when your vehicle's speed is less than 5 mph (8 km/h). Power Door Locks Unlocking the Doors (Two-Stage Unlock) The power door lock control is on the driver and front passenger door panels. Press the button to unlock the driver door.
Locks Locking and Unlocking the Doors with the Key Blade Locking the Doors E138623 Press the button to lock all doors. The direction indicators flash. Locking the Doors Press the button again within three seconds to confirm that all the doors are closed. The doors lock again, the horn sounds and the direction indicators flash if all the doors and the luggage compartment are closed. Note: If the system does not function, use the key blade to lock and unlock your vehicle.
Locks Activating Intelligent Access (If Smart Unlocks for Integrated Keyhead Transmitter Equipped) You must have the intelligent access key within 3.3 ft (1 m) of your vehicle. This helps to prevent you from locking yourself out of your vehicle if the key is still in the ignition. At a Door When you open one of the front doors and lock your vehicle with the power door lock control, all the doors lock then unlock and the horn sounds twice if the key is still in the ignition.
Locks Autounlock You can override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle. To do this, lock your vehicle after you have closed all the doors by: • Using the keyless entry keypad. • Pressing the lock button on another intelligent access key. • Touching the locking area on the handle with another intelligent access key in your hand.
Locks Illuminated Exit WARNINGS Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.
Locks With the Remote Control WARNINGS Keep keys out of reach of children. Do not allow children to play near an open or moving power liftgate. Press the button twice within three seconds. E138630 Closing the Liftgate Note: Cycling the ignition while the liftgate is power closing and is near the latch may cause the liftgate to reverse to full open position. Make sure that you close the liftgate before operating or moving the vehicle, especially in an enclosure, like a garage or a parking structure.
Locks Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components. Note: You can stop the liftgate movement direction with a second press of the instrument panel button or the control button on the liftgate, a double press of the transmitter button, or by using a kicking motion with your foot for hands-free liftgates.
Locks With the Outside Control Button WARNING Keep clear of the liftgate when activating the rear switch. Opening 1. Unlock the liftgate with the remote control or power door unlock control. If an intelligent access transmitter is within 3 ft (1 m) of the liftgate, the liftgate unlocks when you press the liftgate release button. Setting the Liftgate Open Height 1. Open the liftgate. 2. Manually move the liftgate to the desired height. 3.
Locks You can operate the keypad with the factory-set five-digit entry code. The code is on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also program up to five of your own five-digit personal entry codes. When Opening The system stops when it detects an obstacle and two short tones sound. Remove the obstacle to operate the liftgate. Programming a Personal Entry Code KEYLESS ENTRY (If Equipped) 1. Enter the factory-set five-digit code. 2.
Locks Recalling Memory Positions (If Equipped) Unlocking the Driver Door Enter the factory-set or your personal five-digit code. You must press each number within five seconds of each other. The interior lamps illuminate. The programmed entry codes recall driver memory positions as follows: • Entry code 1 recalls driver 1 memory positions. • Entry code 2 recalls driver 2 memory positions. • Entry code 3 recalls driver 3 memory positions. Note: All doors unlock if you enable the all-door unlocking mode.
Locks The factory-set code appears in the information display for a few seconds. Note: The code may not display until after any other warning messages first display. 1 E195807 1. Open the floor console storage compartment lid. 2 E195808 2. With the buttons facing the rear of your vehicle and the key ring up, place the first intelligent access key into the backup slot inside the center console. 3. Press the START/STOP button once and wait a few seconds. 4.
Security The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control. PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in engine starting problems and a loss of security protection.
Security 2. Switch the ignition from off to on. Keep the ignition on for at least 3 seconds, but no more than 10 seconds. 3. Switch the ignition off and remove the first coded key from the ignition. 4. After at least 3 seconds but within 10 seconds of switching the ignition off, insert the second previously coded key into the ignition. 5. Switch the ignition from off to on. Keep the ignition on for at least 3 seconds, but no more than 10 seconds. 6.
Security Arming the Alarm 2. With the buttons facing the rear of your vehicle and the key ring up, place the intelligent access key into the backup slot. 3. Press the push button ignition switch. 4. Wait five seconds and then press the push button ignition switch again. 5. Remove the intelligent access key. 6. Within 10 seconds, place a second programmed intelligent access key in the backup slot and press the push button ignition switch. 7.
Steering Wheel ADJUSTING THE STEERING WHEEL - VEHICLES WITH: POWER ADJUSTABLE STEERING COLUMN ADJUSTING THE STEERING WHEEL - VEHICLES WITH: MANUAL ADJUSTABLE STEERING COLUMN Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 133). WARNING Do not adjust the steering wheel when your vehicle is moving. WARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position.
Steering Wheel End of Travel Position AUDIO CONTROL The steering column sets a stopping position just short of the end of the column position to prevent damage to the steering column. A new stopping position sets if the steering column encounters an object when tilting or telescoping. Select the required source on the audio unit. Operate the following functions with the control: To reset the steering column to its normal stopping position: 1. 2. 3. 4. 5.
Steering Wheel AUDIO CONTROL (If Equipped) VOICE CONTROL (If Equipped) You can operate the following functions with the control: E168194 Press the button to select or deselect voice control. See SYNC™ (page 354). E196496 A Volume up. B Volume down. C Mute. D Seek down or previous. E Seek up or next. CRUISE CONTROL Type 1 Seek, Next or Previous Press the seek button to: • Tune the radio to the next or previous stored preset. • Play the next or the previous track.
Steering Wheel Information Display Control Features Type 2 E191247 E144811 See Cruise Control (page 196). This control functions the same as the center control on the faceplate. See Audio Unit (page 343). INFORMATION DISPLAY CONTROL Use this control to adjust the right side of the information display. Navigate through the screen and press OK to select. HEATED STEERING WHEEL (If Equipped) See MyFord Touch™ (page 388). E144636 See Information Displays (page 100).
Wipers and Washers Intermittent Wipe WINDSHIELD WIPERS Note: Fully defrost the windshield before you switch the windshield wipers on. A B Note: Make sure you switch the windshield wipers off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. C Note: Do not operate the wipers on a dry windshield.
Wipers and Washers Use the rotary control to adjust the sensitivity of the rain sensor. Set the control to low sensitivity, and the wipers will turn on when the rain sensor detects a large amount of moisture on the windshield. Set the control to high sensitivity, and the wipers will turn on when the rain sensor detects a small amount of moisture on the windshield. Note: Wet or winter driving conditions with ice, snow or salty road mist can cause inconsistent and unexpected wiping or smearing.
Wipers and Washers Rear Window Washer A wipe will occur a few seconds after washing to clear any remaining washer fluid. This feature can be switched on or off in the information display. See General Information (page 100). Front Camera Washer (If Equipped) Operating the windshield washer will also operate the front camera washer. REAR WINDOW WIPER AND WASHERS E167407 Push the lever away from you to operate the rear window washer. When you release the lever, wiping continues for a short period of time.
Lighting GENERAL INFORMATION LIGHTING CONTROL Condensation in Lamp Assemblies Exterior lamps have vents to accommodate normal changes in air pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens.
Lighting Headlamp Flasher If equipped, the following also activate when the lighting control is in the autolamps position and you switch them on in the information display: • Configurable daytime running lamps. • Automatic high beam control. • Adaptive headlamp control. The headlamps remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps remain on. See Information Displays (page 100).
Lighting INSTRUMENT LIGHTING DIMMER DAYTIME RUNNING LAMPS (If Equipped) Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting. WARNING The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog.
Lighting 3. The transmission is not in park (P) for vehicles with automatic transmissions or the parking brake is released for vehicles with manual transmissions. 4. The lighting control is in the autolamps position. 5. The headlamps are off. Note: Typical road dust, dirt and water spots will not affect the performance of the automatic high beam system . However, in cold or inclement weather conditions, you will notice a decrease in the availability of the high beam system, especially at start up.
Lighting DIRECTION INDICATORS E142451 Switch the lighting control to the autolamps position. E169255 Push the lever up or down to use the direction indicators. Manually Overriding the System Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change.
Lighting Note: Press the button to switch the door function off when you open any door. The indicator lamp will light amber when the door function is off. When the door function is off and you open a door, the courtesy and door lamps will stay off. Press the button again to switch the door function back on. The indicator lamp will light blue when the door function is on. When the door function is on and you open a door, the courtesy and door lamps will light.
Lighting Type 3 Type 2 E199026 Type 3 C B A E199027 C You can switch dome lamps on by pressing the button. E199032 A Door function button B All lamps on button C Individual dome lamps AMBIENT LIGHTING (If Equipped) The ambient lighting system is adjusted with the touchscreen system. See MyFord Touch™ (page 388). You can switch individual map lamps on independently by pressing a map lens.
Windows and Mirrors 2. Release the control. 3. Open the window and then try to close it automatically. 4. Repeat the procedure if the window does not close automatically. Note: The one-touch down and one-touch up feature only applies to the front windows. POWER WINDOWS WARNINGS Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves.
Windows and Mirrors To adjust your mirrors, switch your vehicle on (with the ignition in accessory mode or the engine running) and then: 1. Select the mirror you want to adjust. The control lights. 2. Use the adjustment control to adjust the position of the mirror. 3. Press the mirror control again. The control light turns off. Note: To operate this feature, accessory delay must not be active.
Windows and Mirrors Integrated Blind Spot Mirror (If The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image transitions from the main mirror and begins to appear in the blind spot mirror as the vehicle approaches (B). The vehicle transitions to your peripheral field of view as it leaves the blind spot mirror (C).
Windows and Mirrors The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up. MOONROOF (If Equipped) WARNINGS Do not let children play with the moonroof or leave them unattended in the vehicle. They may seriously hurt themselves.
Windows and Mirrors C Sunshade open. Press and release to open the sunshade. The sunshade opens automatically with the moonroof. You can also open the sunshade with the moonroof closed. Note: The sunshade stops short of its fully opened position for the comfort of rear passengers. To open the sunshade fully, press the control again. D Sunshade close. Press and release to close the sunshade. E Moonroof close. Press and release to close the moonroof from either the open or vent positions.
Instrument Cluster GAUGES Type 1 E144485 A Tachometer B Information Display C Speedometer D Fuel Gauge E Engine Coolant Temperature Gauge Outside Air Temperature Information Display Shows the outside air temperature. Odometer Compass Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. Displays the vehicle’s heading direction. Trip Computer See General Information (page 100).
Instrument Cluster Switch the ignition on. The fuel gauge indicates approximately how much fuel is left in the fuel tank. The arrow adjacent to the fuel pump symbol indicates on which side of your vehicle the fuel filler door is located. Vehicle Settings and Personalization See General Information (page 100). Engine Coolant Temperature Gauge Shows the temperature of the engine coolant. At normal operating temperature, the needle remains in the center section.
Instrument Cluster Type 2 E144486 A Left Information Display B Speedometer C Right Information Display See General Information (page 100). Left Information Display WARNING LAMPS AND INDICATORS Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will illuminate when you start your vehicle to make sure they work.
Instrument Cluster Note: Some warning indicators appear in the information display and function the same as a warning lamp, but do not display when you start your vehicle. Brake System Adaptive Cruise Control (If Equipped) If it illuminates when you are driving, check that you do not have the parking brake engaged. If you do not have the parking brake engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by an authorized dealer.
Instrument Cluster Electric Park Brake Heads Up Display (If Equipped) It will illuminate or flash when the electric parking brake has a E146190 malfunction. See Electric Parking Brake (page 176). A red beam of lights will illuminate on the windshield in certain instances when using adaptive cruise control or the collision warning system. It will also illuminate momentarily when you start your vehicle to make sure the display works.
Instrument Cluster Low Washer Fluid When you first switch the ignition on, before engine start, the service engine soon indicator light illuminates to check the bulb and to indicate whether your vehicle is ready for inspection maintenance testing. It will illuminate when the windshield washer fluid is low. E132353 Normally, the service engine soon light will stay on until you crank the engine, and then turn itself off if no malfunctions are present.
Instrument Cluster Keyless Warning Alert (If Equipped) Sounds the horn twice when you exit your vehicle with the intelligent access key, after the last door is closed and your keyless vehicle is in RUN, indicating your vehicle is still on. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle.
Information Displays Information Display Controls (Type 1) GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any handheld device while driving and encourage the use of voice-operated systems when possible.
Information Displays Trip 1 and 2 Average Fuel Outside Temperature All Values • • • • • • • • Digital Speedo - Shows a digital display of your vehicle speed. Distance to E - Shows the approximate distance your vehicle can travel before running out of fuel. Trip Odometer — Registers the distance of individual journeys. Trip Timer — The timer stops when you turn your vehicle off and restarts when you restart your vehicle. Fuel Used — Shows the amount of fuel used for a given trip.
Information Displays Fuel Economy All Values Auto StartStop • • • • • • • Distance to Empty - Shows the approximate distance your vehicle can travel before running out of fuel. Inst Fuel Economy - Shows a visual graph of your instantaneous fuel economy along with your Avg MPG since the function was last reset. Long Term Fuel Economy - Shows your long term fuel economy. Fuel History - Shows a bar chart of your fuel history. Average Fuel — Shows the average fuel economy for a given trip.
Information Displays Driver Assist Rear Park Aid - check enabled or uncheck disabled Tire Monitor Tire Pressure Trailer Sway - check enabled or uncheck disabled Tire Pressure E194202 Displays your current vehicle tire pressures.
Information Displays Settings Duration 5, 10 or 15 minutes System - check enabled or uncheck disabled Windows Remote Open or Remote Close MyKey Wipers Courtesy Wipe or Rain Sensing Create MyKey Hold OK to Create MyKey 911 Assist Always On or User Selectable Do Not Disturb On or Off Traction Control Always On or User Selectable MAX Speed Choose desired speed or Off Speed Minder Choose desired speed or Off Volume Limiter - check enabled or uncheck disabled Clear MyKeys Display Setup Hold O
Information Displays Information Display Controls (Type 2) • • Press and hold the left arrow button at any time to return to the main menu display (escape button). Press the OK button to choose and confirm settings or messages. Main menu From the main menu bar on the left side of the information display, you can choose from the following categories: • • • • • E144638 • • • Press the up and down arrow buttons to scroll through and highlight the options within a menu.
Information Displays Trip 1 & 2 Note: Some options may appear slightly different or not at all if the items are optional. You can access the menu using the information display control. Trip 1 and 2 All Values All Values — shows all trip values (Trip Timer, Odometer and Average Fuel). • • • Trip Odometer — Shows your accumulated trip distance. Trip Timer— The timer stops when you turn your vehicle off and restarts when you restart your vehicle.
Information Displays Driver Assist Traction Control - check enabled or uncheck disabled Adaptive Steering Steering in D Sport or Normal Steering in S Sport or Normal Blind Spot - check enabled or uncheck disabled Cross Traffic Alert - check enabled or uncheck disabled Cruise Control Adaptive or Normal Driver Alert Driver Alert or Driver Alert Display Driver Select Suspension Sport, Normal or Comfort Hill Start Assist - check enabled or uncheck disabled Lane Keeping System Pre-Collision Mode
Information Displays Settings Vehicle Auto Engine Off - check enabled or uncheck disabled DTE Calculation Normal or Towing Easy Entry/Exit - check enabled or uncheck disabled Lighting Adaptive Headlamps Adaptive Headlamps - check enabled or uncheck disabled Traffic Set Up Right or Left Hand Traffic Auto Highbeam - check enabled or uncheck disabled Autolamp Delay Off or XX Seconds Daytime Lights - check enabled or uncheck disabled Locks Autounlock - check enabled or uncheck disabled Relock - chec
Information Displays Settings Windows Remote Open or Remote Close MyKey Wipers Courtesy Wipe or Rain Sensing Create MyKey Hold OK to Create MyKey 911 Assist Always On or User Selectable Do Not Disturb On or Off Traction Control Always On or User Selectable MAX Speed Choose desired speed or Off Speed Minder Choose desired speed or Off Volume Limiter - check enabled or uncheck disabled Clear MyKeys Display Setup Hold OK to Clear All MyKeys Distance Miles & Gallons, l/100km or km/l Gauge Dis
Information Displays Press the OK button to acknowledge and remove some messages from the information display. The information display will automatically remove other messages after a short time. You need to confirm certain messages before you can access the menus. E144636 Active Park Message Action Active Park Fault The system requires service due to a malfunction. Contact an authorized dealer.
Information Displays Message Action Adaptive Cruise - Driver Resume Control The adaptive cruise has reinstated controls to the driver. Adaptive Cruise Speed Too Low to Activate Your vehicle speed is too slow to activate the adaptive cruise. Adaptive Cruise Shift Down The adaptive cruise is automatically adjusting the gap distance and the driver needs to shift the transmission into a lower gear.
Information Displays All-Wheel Drive Message Action AWD Temporarily Disabled The all-wheel drive system temporarily turns off to protect itself from overheating. AWD Off The all-wheel drive system temporarily turns off to protect itself from overheating or if you are using the temporary spare tire. AWD Restored The all-wheel drive system will resume normal function and clear this message after driving a short distance with the road tire re-installed or after the system cools.
Information Displays Auto Start-Stop Message Action Auto StartStop Press Brake to Start Engine The engine needs to be restarted, press the brake pedal to start. Auto StartStop Press The engine needs to be restarted, press the brake pedal harder Brake Harder to Activate to start. Auto StartStop Press Any Pedal The engine needs to be restarted, press any pedal to start. Auto StartStop Select Neutral To Start Engine Select neutral for the system to restart the engine.
Information Displays Blind Spot Information and Cross Traffic Alert System Message Action Blindspot System Fault A fault with the system has occurred. Contact an authorized dealer as soon as possible. Blindspot Not Available Sensor Blocked See Manual The system sensors are blocked. See Blind Spot Information System (page 208). Cross Traffic Vehicle Coming From X The system detects a vehicle. See Blind Spot Information System (page 208).
Information Displays Driver Alert Message Action Driver Alert Warning Rest Now Stop and rest as soon as it is safe to do so. Driver Alert Warning Rest Suggested Take a rest break soon. Electronic Stability Control Message Action ESC Service required The system detects a malfunction due to a blocked sensor. ESC off The traction control system status. ESC on The traction control system status. ESC Sport mode The traction control system status.
Information Displays Fuel Message Fuel Level Low Action An early reminder of a low fuel condition. Check Fuel Fill Inlet The fuel fill inlet may not be properly closed. Fuel Door Opening Wait for up to 15 seconds while the fuel system depressurizes. Fuel Door Open The fuel system has finished depressurizing and you can begin to refuel. Close Fuel Door A reminder to close the fuel door. Hill Start Assist Message Action Hill Start Assist Not Available Hill start assist is not available.
Information Displays Message Action Not Enough Keys Learned You have not programmed enough keys to the system. Key Battery Low Replace The key battery is low. Change the battery as soon as possible. Soon Engine On Informs you that they you are exiting your vehicle and the engine is on. Lane Keeping System Message Action Lane Keeping Sys. Malfunction Service Required The system has malfunctioned. Contact an authorized dealer as soon as possible.
Information Displays Message Action Check Brake System The brake system needs servicing. Stop your vehicle in a safe place. Contact an authorized dealer. Engine Coolant Overtemperature The engine coolant temperature is excessively high. Power Reduced to Lower Engine Temp The engine has reduced power to help reduce high engine temperature. Transport / Factory Mode Your vehicle is still in Transport or Factory mode. This may not allow some features to operate properly. Contact an authorized dealer.
Information Displays Message Action Traction Control On MyKey Setting With a MyKey in use, traction control turns on. MyKey Park Aid Cannot be Deactivated With a MyKey in use, park aid is always on. Lane Keeping Alert On MyKey Setting With a MyKey in use, lane keeping alert turns on. Park Aid Message Action Check Front Park Aid The system has detected a condition that requires service. Contact an authorized dealer. See Front Parking Aid (page 184).
Information Displays Message Action Park Brake Limited Function Service Required The electric park brake system has detected a condition that requires service. See an authorized dealer. Park Brake System Overheated You have not released the electric parking brake causing it to overheat. Release Park Brake The electric parking brake is set and you have started your vehicle. Park Brake Applied The electric parking brake is set. Park Brake Released You have released the electric parking brake.
Information Displays Remote Start Message Action To Drive: Press Brake and Gear Shift Button A reminder to apply the brake and push the gearshift button to drive your vehicle after a remote start. Seats Message Action Memory Recall Not A reminder that memory seats are not available while driving. Permitted While Driving Memory X Saved Shows where you have saved your memory setting. Starting System Message Action Press Brake to Start A reminder to apply the brake when starting your vehicle .
Information Displays Towing Message Action Trailer Sway Reduce Speed Your trailer sway control has detected trailer sway so you need to reduce your speed. Traction Control Message Action Traction Control Off The status of the traction control system. See Using Traction Control (page 180). Traction Control On The status of the traction control system. See Using Traction Control (page 180). Transmission Message Transmission Malfunction Service Now Action See an authorized dealer.
Information Displays Message Transmission Adapt Mode Action The transmission is adjusting the shift strategy. Transmission Indicate Mode Lockup On The transmission is locked and unable to select gears. Transmission Indicate Mode Lockup Off The transmission is unlocked and free to select gears.
Climate Control MANUAL CLIMATE CONTROL - VEHICLES WITH: ELECTRONIC MANUAL TEMPERATURE CONTROL (EMTC) E188680 A Fan speed control: Adjusts the volume of air circulated in the vehicle. B Air distribution control: Adjust the control to turn airflow from the windshield, instrument panel, or footwell vents on or off. You can distribute air through any combination of these vents. C Temperature control: Controls the temperature of the air circulated in your vehicle.
Climate Control E MAX A/C: Adjust the control for maximum cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. F Recirculated air: Press the button to switch between outside air and recirculated air. The air currently in the passenger compartment recirculates. This can reduce the time needed to cool the interior and reduce unwanted odors from entering your vehicle.
Climate Control AUTOMATIC CLIMATE CONTROL - VEHICLES WITH: DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) E198814 A Driver temperature control: Adjust the temperature setting using the control on the driver side. This control also adjusts the passenger side temperature when you switch off dual zone mode. B Fan speed control: Adjust the volume of air circulated in the vehicle. C Passenger temperature control: Adjust the temperature on the passenger side.
Climate Control G A/C: Press the button to switch the air conditioning on or off. Air conditioning cools your vehicle using outside air. To improve the time to reach a comfortable temperature in hot weather, drive with the windows open until you feel cold air through the air vents. Note: In certain conditions (for example, maximum defrost), the air conditioning compressor may continue to operate even though the air conditioning is switched off. H Power: Press the button to switch the system on and off.
Climate Control E198947 A A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. Note: In certain conditions (such as when using Max Defrost), the air conditioning compressor may continue to operate even after you switch off the air conditioning with the A/C button. B MAX A/C: Press the button to maximize cooling.
Climate Control E Heated seats (if equipped): Press the button to switch the heated seats on and off. See Heated Seats (page 140). F Climate controlled seats (if equipped): Press the button to switch the climate controlled seats on and off. See Climate Controlled Seats (page 141). G Passenger temperature control: Adjusts the temperature on the passenger side. H Fan speed control: Adjusts the volume of air circulated in the vehicle.
Climate Control Note: To improve the time to reach comfort in hot weather, drive with the windows slightly open for 2-3 minutes after start-up or until your vehicle airs out. 2. Adjust the temperature control to the desired setting. Recommended Settings for Heating In mild weather, you can improve your fuel economy when using the climate control system by using outside air instead of air conditioning. • Turn the temperature control knob(s) so the interior temperature is set to 60°F (15.5°C).
Climate Control You can locate the cabin air filter behind the glove box. HEATED WINDOWS AND MIRRORS (If Equipped) Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. Heated Rear Window Note: Make sure the engine is running before operating the heated windows. Press the button to clear the heated rear window of thin ice E184884 and fog.
Climate Control Automatic Settings In hot weather, the system is set to 72°F (22°C). The cooled seats are set to high (if available, and selected to AUTO in the information display). In moderate weather, the system either heats or cools (based on previous settings). The rear defroster, heated mirrors and heated seats do not automatically turn on. In cold weather, the system is set to 72°F (22°C). The heated seats are set to high (if available, and selected to AUTO in the information display).
Seats We recommend that you follow these guidelines: • Sit in an upright position with the base of your spine as far back as possible. • Do not recline the seatback more than 30 degrees. • Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. • Keep sufficient distance between yourself and the steering wheel. We recommend a minimum of 10 in (25 cm) between your breastbone and the airbag cover.
Seats The head restraints consist of: WARNINGS Install the head restraint properly to help minimize the risk of neck injury in the event of a crash. Note: Adjust the seatback to an upright driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position.
Seats The driver and passenger manual seats may consist of: E144631 A B C D E144727 Adjust the seatback to an upright driving or riding position. 2. Pivot the head restraint forward toward your head to the desired position. A A bar to move the seat backward and forward. B A control to adjust the lumbar of the seatback (driver seat only). After the head restraint reaches the forward-most tilt position, pivoting it forward again will then release it to the rearward, un-tilted position.
Seats 6-way power seat E176793 136 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Seats 10-way power seat E196499 Power Lumbar (If Equipped) MEMORY FUNCTION (If Equipped) WARNINGS Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts. Do not use the memory function when your vehicle is moving. This feature automatically recalls the position of the driver seat, power mirrors and optional power steering column. The memory control is located on the driver door.
Seats You can also recall a preset memory position by: • Pressing the unlock button on your intelligent access key fob if it is linked to a preset position. • Unlocking the intelligent driver door handle if a linked key fob is present. • Entering a personal entry code on the Securicode keypad. See Locks (page 60). E142554 Note: Using a linked key fob to recall your memory position when the ignition is off moves the seat to the Easy Entry position. Saving a PreSet Position 1. Switch the ignition on. 2.
Seats Easy Entry and Exit Feature Reclining the Seatback If you enable the easy entry and exit feature, it automatically moves the driver seat position rearward up to two inches (five centimeters) when you switch the ignition off. With the seat occupied, pull the lever up to recline the seatback. Easy Fold™ Folding Seat (If Equipped) WARNING The driver seat will return to the previous position when you switch the ignition on. Make sure that the seat is unoccupied when folding it down.
Seats Rear Seats (If Equipped) HEATED SEATS (If Equipped) WARNING Front Seats Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time.
Seats The heated seat module resets at every ignition run cycle. While the ignition is on, press the high or low heated seat switch to enable heating mode. When activated, they will turn off automatically when you turn the engine off. CLIMATE CONTROLLED SEATS E146322 (If Equipped) Touch the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings.
Seats REAR SEAT ARMREST E144635 Fold the armrest down to use the armrest and cupholder.
Universal Garage Door Opener HomeLink Wireless Control System (If Equipped) The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. WARNING Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982).
Universal Garage Door Opener 3. Using both hands, simultaneously, press and hold the desired HomeLink button and the hand-held transmitter button. DO NOT release either one until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing indicates successful training. 4. Press and hold the HomeLink button you programmed for five seconds, then release. You may need to do this twice to activate the door.
Universal Garage Door Opener A 1. Press and hold the outer two function buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly. 2. When the indicator lights flash, release the buttons. The codes for all buttons are erased. A. Red indicator light B. Green indicator light 1. Press and hold one of the buttons on the hand-held transmitter for 10 seconds. The indicator light will change from green to red and green. 2.
Universal Garage Door Opener 1. Press and hold the previously programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green. 2. Press the same button twice to confirm the change. If done correctly the indicator light will turn green. 5. Press and hold the previously programmed button on the visor for 2 seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete.
Auxiliary Power Points 12 Volt DC Power Point • • • • WARNING Do not plug optional electrical accessories into the cigar lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. On the center console. Inside the center console. On the rear of the console. In the cargo area. 110 Volt AC Power Point (If Equipped) WARNING Do not keep electrical devices plugged in the power point whenever the device is not in use.
Auxiliary Power Points The power point temporarily turns off power if it exceeds the 150 watt limit. It can also switch to a fault mode if it detects overloading, overheating, or shorting conditions. For overloading and shorting conditions, unplug your device and switch the ignition off then on. For an overheating condition, let the system cool off first. Switch the ignition off then on.
Storage Compartments CENTER CONSOLE OVERHEAD CONSOLE Stow items in the cupholder carefully as items may become loose during hard braking, acceleration or collisions, including hot drinks which may spill. Available console features include: F E75193 Press near the rear edge of the door to open it. A B C E E190439 D A Auxiliary power point (if equipped). B Storage compartment with auxiliary input jack, media hub, and optional USB port. C Cupholder. D Storage tray.
Starting and Stopping the Engine GENERAL INFORMATION IGNITION SWITCH WARNINGS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, creating the risk of fire. E72128 0 (off) - The ignition is off.
Starting and Stopping the Engine Ignition Modes Note: You can crank the engine for a total of 60 seconds without the engine starting before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine 3 times for 20 seconds each time, without the engine starting, you reached the 60-second time limit. A message appears in the information display alerting you that you exceeded the cranking time.
Starting and Stopping the Engine Vehicles with Keyless Start Note: Do not touch the accelerator pedal. Note: A valid passive key must be located inside your vehicle to switch the ignition on and start your vehicle. 1. Fully depress the brake pedal. 2. Briefly press the push button ignition switch. 2 The system does not function if: • The passive key frequencies are jammed. • The key battery has no charge. E195808 If you are unable to start the engine, do the following: 2.
Starting and Stopping the Engine Failure to Start You can stop the shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: • Reset the timer by pressing the brake or accelerator pedal. • Temporarily switch off the shutdown feature during the current ignition cycle using the information display. See (page 100). • Press OK or RESET to temporarily switch the feature off during the current ignition cycle.
Starting and Stopping the Engine Stopping the Engine When Your Vehicle is Moving Guarding Against Exhaust Fumes WARNING WARNING If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance.
Starting and Stopping the Engine The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source.
Unique Driving Characteristics • • • • • AUTO-START-STOP (If Equipped) The system helps reduce fuel consumption by automatically shutting off and restarting the engine while your vehicle is stopped. The engine will restart automatically when you release the brake pedal. In some situations, your vehicle may restart automatically, for example: • • • • To maintain interior comfort To recharge the battery • Note: Power assist steering is turned off when the engine is off.
Unique Driving Characteristics • • • • • • • • • • You press the accelerator and the brake pedal at the same time. The driver safety belt becomes unfastened or the driver door is ajar. The transmission is moved from drive (D). Your vehicle is moving. The interior compartment does not meet customer comfort when air conditioning or heat is on. Fogging of the windows could occur and the air conditioning is on. The battery is not within optimal operating conditions. The maximum engine off time is exceeded.
Fuel and Refueling • SAFETY PRECAUTIONS WARNINGS Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury. • Automotive fuels can cause serious injury or death if misused or mishandled.
Fuel and Refueling • FUEL QUALITY Choosing the Right Fuel • The use of fuels with metallic compounds such as methylcyclopentadienyl manganese tricarbonyl (commonly known as MMT), which is a manganese-based fuel additive, will impair engine performance and affect the emission control system. E161513 We recommend regular unleaded gasoline with a minimum pump octane rating of 87. Some stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas.
Fuel and Refueling Filling a Portable Fuel Container 1. Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Only use an approved fuel container to transfer fuel to your vehicle. Place the container on the ground when filling it. • Do not fill a fuel container when it is inside your vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container when filling it.
Fuel and Refueling 1. WARNINGS Read and follow all the instructions on the pump island. Put the vehicle in position P and switch the ignition off. Switch off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Keep sparks, flames and smoking materials away from fuel. Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is against the law in some places. E166527 2.
Fuel and Refueling If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after four or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. E154765 FUEL CONSUMPTION Note: Allow about five to ten seconds after pumping fuel before removing the fuel filler nozzle.
Fuel and Refueling Calculating Fuel Economy WARNINGS Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Fuel and Refueling An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. • • You can correct these temporary malfunctions by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out.
Fuel and Refueling Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, your vehicle is not ready for I/M testing.
Transmission Reverse (R) AUTOMATIC TRANSMISSION With the gearshift lever in reverse (R), your vehicle moves backward. Always come to a complete stop before shifting into and out of reverse (R). WARNINGS Always set the parking brake fully and latch the gearshift in park (P). Turn the ignition to the off position and remove the key whenever you leave your vehicle. Neutral (N) With the gearshift lever in neutral (N), your vehicle can be started and is free to roll.
Transmission In order to prevent the engine from running at too low an RPM, which may cause it to stall, SelectShift still automatically makes some downshifts if it has determined that you have not downshifted in time. Although SelectShift makes some downshifts for you, it still allows you to downshift at any time as long as the SelectShift determines that damage will not be caused to the engine from over-revving.
Transmission Your vehicle is equipped with a brake-shift interlock feature that prevents moving the gearshift lever from park (P) when the ignition is in the on position and the brake pedal is not pressed. If you cannot move the gearshift lever out of park (P) position with the ignition in the on position and the brake pedal pressed, a malfunction may have occurred. It is possible that a fuse has blown or your vehicle’s brake lamps are not operating properly. See Fuse Specification Chart (page 248).
Transmission If your vehicle gets stuck in mud or snow, you may rock it out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear.
All-Wheel Drive (If Equipped) Do not use a spare tire of a different size other than the tire provided. If the mini-spare tire is installed, the AWD system may disable automatically and enter front-wheel drive only mode to protect driveline components. This condition will be indicated by a warning in the information display See Information Messages (page 109).
All-Wheel Drive (If Equipped) If Your Vehicle Goes Off the Edge of the Pavement • • • Note: Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface.
All-Wheel Drive (If Equipped) Sand Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
All-Wheel Drive (If Equipped) Driving on Hilly or Sloping Terrain Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. The front wheels have to be turning in order to steer the vehicle. Note: Avoid driving crosswise or turning on steep slopes or hills.
All-Wheel Drive (If Equipped) Avoid sudden braking as well. Although an AWD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster, because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions. Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, apply the brake steadily.
Brakes Brake Assist GENERAL INFORMATION Brake assist detects when you brake rapidly by measuring the rate at which you press the brake pedal. It provides maximum braking efficiency as long as you press the pedal, and can reduce stopping distances in critical situations. Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out. Have the system checked by an authorized dealer.
Brakes Note: The brake system warning lamp will illuminate for ten seconds, if the ignition is turned off after the electric parking brake has been applied, or the electric parking brake has been applied after the ignition has been turned off. ELECTRIC PARKING BRAKE The electric parking brake replaces the conventional handbrake. The operating switch is located in the center console. WARNING Note: The electric parking brake will not automatically apply.
Brakes Manual release WARNINGS With the exception of emergency conditions (for example, the brake pedal does not work or is blocked), do not apply the electric parking brake while the vehicle is moving. On bends, or poor road surfaces or weather conditions, emergency braking can cause the vehicle to skid out of control or off the road. WARNING If the brake system warning light remains illuminated or flashes after you have released the parking brake, there could be a problem with you braking system.
Brakes Note: On manual transmission vehicles, you must fully press the clutch pedal before the drive away release feature will operate. Drive as normal using the accelerator and clutch pedals and the electric parking brake will be automatically released. HILL START ASSIST WARNINGS The system does not replace the parking brake. When you leave your vehicle, always apply the parking brake. Failure to leave your vehicle securely parked may lead to a crash or injury. See Electric Parking Brake (page 176).
Brakes Note: There is no warning light to indicate the system is either on or off. Using Hill Start Assist 1. Press the brake pedal to bring your vehicle to a complete standstill. Keep the brake pedal pressed. 2. If the sensors detect that your vehicle is on a slope, the system activates automatically. 3. When you remove your foot from the brake pedal, your vehicle remains on the slope without rolling away for about two to three seconds.
Traction Control System Indicator Lights and Messages PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. WARNING If a failure has been detected within the AdvanceTrac system, the stability control light will illuminate steadily. Verify that the AdvanceTrac system was not manually disabled through the information display. If the stability control light still illuminates steadily, have the system serviced by an authorized dealer immediately.
Stability Control handling in following the road during adverse maneuvering, roll stability control helps avoid a vehicle rollover, and the traction control system helps avoid drive wheel spin and loss of traction. See Using Traction Control (page 180).
Stability Control USING STABILITY CONTROL AdvanceTrac® with Roll Stability Control™ (RSC®) The system automatically activates when you start your vehicle. The AdvanceTrac with RSC system cannot be completely turned off, but the electronic stability control and roll stability control portions of the system are disabled when the transmission is in reverse (R). You can also turn off the traction control portion of the system independently. See Using Traction Control (page 180).
Parking Aids (If Equipped) Note: The sensing system cannot be turned off when a MyKey is present. See Principle of Operation (page 54). PRINCIPLE OF OPERATION WARNINGS To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving on a flat surface at parking speeds.
Parking Aids (If Equipped) The indicator displays: • As the distance to the obstacle decreases the indicator blocks illuminate and move towards the vehicle icon. • If there is no obstacle detected, the distance indicator blocks are greyed out. FRONT PARKING AID (If Equipped) The front sensors are active when the transmission is in any position other than park (P). E130178 Coverage area of up to 6 ft (1.8 m) from the rear bumper. There may be decreased coverage area at the outer corners of the bumper.
Parking Aids (If Equipped) Note: Obstacles that enter the side detection area without being detected and mapped by the front or rear side sensors will not be detected. The indicator displays: • As the distance to the obstacle decreases the indicator blocks illuminate and move towards the vehicle icon. • If there is no obstacle detected, the distance indicator blocks are greyed out. The side sensors are active when the transmission is in any position other than park (P).
Parking Aids (If Equipped) Obstacle Distance Indicator (If 7 mph (12 km/h) or below and obstacles are detected within 12 in (30 cm), or when obstacles are detected within 12–24 in (30–60 cm) and are inside the driving path of your vehicle. When you stop your vehicle the audible warning stops after 2 seconds and the visual distance indication stops after 4 seconds. Equipped) Note: If the obstacle remains within 12 in (30 cm) visual distance indication remains on.
Parking Aids (If Equipped) The system may not correctly operate in any of the following conditions: • You use a spare tire or a tire significantly worn more than the other tires. • You use a unauthorized tire size. • You try to park on a tight curve. • Something passes between the front bumper and the parking space (a pedestrian or cyclist). • The edge of the neighboring parked vehicle is high off the ground (for example, a bus, tow truck or flatbed truck).
Parking Aids (If Equipped) When driving at a speed less than 22 mph (35 km/h) the system automatically scans both sides of your vehicle for an available parking space. The system displays a message and a corresponding graphic to indicate it is searching for a parking space. Use the direction indicator to select searching either to the left-hand side or right-hand side of your vehicle. A E130107 Note: If the direction indicators are not used, the system defaults to the passenger side of your vehicle.
Parking Aids (If Equipped) E130108 Using Active Park Assist Perpendicular Parking When you think your vehicle is properly parked, or you hear a solid tone from the parking aid (accompanied by a display message and a chime), bring your vehicle to a complete stop. Press the button located on the center console near the gearshift lever or the right side of the center stack twice.
Parking Aids (If Equipped) Note: The system always offers the last detected parking space (for example, if your vehicle detects multiple spaces while you are driving, it offers the last one). When you shift the transmission into reverse ( R), with your hands off the wheel (and nothing obstructing its movement), your vehicle steers itself into the space. The system displays instructions to move your vehicle back and forth in the space.
Parking Aids (If Equipped) Deactivating the Active Park Assist Feature The system determines the clearance to the front and rear of your vehicle and automatically steers your vehicle out of a parallel parking space (hands-free) while you control the accelerator, gearshift and brakes. The system visually and audibly guides you to enter traffic. Manually deactivate the system by: • Pressing the active park assist button twice. • Grabbing the steering wheel during an active maneuver.
Parking Aids (If Equipped) The system does not offer a particular space The sensors may be covered (for example, snow, ice or dirt buildup). Covered senors can affect the system's functionality. There is not enough room in the parking space for your vehicle to safely park. There is not enough space for the parking maneuver on the opposite side of the parking space. The parking space is farther than 5 ft (1.5 m) or closer than 16 in (0.4 m) away. The transmission is in reverse ( R).
Parking Aids (If Equipped) REAR VIEW CAMERA WARNINGS The rear view camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the interior and exterior mirrors for maximum coverage. Objects that are close to either corner of the bumper or under the bumper, might not be seen on the screen due to the limited coverage of the camera system. E142435 The camera is located on the luggage compartment door.
Parking Aids (If Equipped) Note: When towing, the camera only sees what you are towing. This might not provide adequate coverage as it usually provides in normal operation and some objects might not be seen. In some vehicles, the guidelines may disappear when you connect the trailer tow connector. A B C D E The camera may not operate correctly under the following conditions: • Nighttime or dark areas if one or both reverse lamps are not operating. • Mud, water or debris obstructs the camera's view.
Parking Aids (If Equipped) Enhanced Park Aids or Park Pilot Always use caution while reversing. Objects in the red zone are closest to your vehicle and objects in the green zone are farther away. Objects are getting closer to your vehicle as they move from the green zone to the yellow or red zones. Use the side view mirrors and rear view mirror to get better coverage on both sides and rear of the vehicle. Selectable settings for this feature are ON and OFF.
Cruise Control 2. Press and release SET+. PRINCIPLE OF OPERATION 3. Take your foot off the accelerator pedal. Note: The indicator will change color. Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. You can use cruise control when your vehicle speed is greater than 20 mph (30 km/h). Note: Cruise control disengages if the vehicle speed decreases more than 10 mph (16 km/h) below the set speed while driving uphill.
Cruise Control The adaptive cruise controls are on the steering wheel. USING ADAPTIVE CRUISE CONTROL (If Equipped) Switching Adaptive Cruise Control On WARNINGS Always pay close attention to changing road conditions when using adaptive cruise control. The system does not replace attentive driving. Failing to pay attention to the road may result in a crash, serious injury or death. Press and release ON. The indicator appears in the instrument cluster.
Cruise Control The system applies the brakes to slow your vehicle to maintain a safe gap distance from the vehicle in front. The maximum braking which the system applies is limited. You can override the system by applying the brakes. Note: When adaptive cruise control is active, the speedometer may vary slightly from the set speed displayed in the information display.
Cruise Control The selected gap appears in the information display as shown by the bars in the graphic. Five gap settings are available. The gap setting is time dependent and the distance automatically adjusts with your vehicle speed. E164805 Adaptive cruise control gap settings mph ( km/h) Graphic display, bars indicated between vehicles Time gap, seconds 62 (100) 1 1 31 (28) Sport 62 (100) 2 1.4 43 (39) Normal 62 (100) 3 1.8 55 (50) Normal 62 (100) 4 2.
Cruise Control Detection Issues The system may apply the brakes to slow the vehicle to the new set speed. The set speed displays continuously in the information display while the system is active. WARNING On rare occasions, detection issues can occur due to the road infrastructures, for example bridges, tunnels and safety barriers. In these cases, the system may brake late or unexpectedly. At all times, you are responsible for controlling your vehicle, supervising the system and intervening, if required.
Cruise Control Blocked Sensor Detection issues can occur: A When driving on a different line than the vehicle in front. B With vehicles that edge into your lane. The system can only detect these vehicles once they move fully into your lane. C There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road. WARNINGS Do not use the system when towing a trailer with brake controls.
Cruise Control The following table lists possible causes and actions for this message displaying. Cause Action The surface of the radar in the grille is dirty Clean the grille surface in front of the radar or obstructed in some way. or remove the object causing the obstruction. The surface of the radar in the grille is clean Wait a short time. It may take several but the message remains in the display. minutes for the radar to detect that it is free from obstruction.
Driving Aids When activated, the system will monitor your alertness level based upon your driving behavior in relation to the lane markings, and other factors. DRIVER ALERT (If Equipped) PRINCIPLE OF OPERATION WARNING System Warnings The driver alert system is designed to aid you. It is not intended to replace your attention and judgment. You are still responsible to drive with due care and attention. Note: The system will not issue warnings below approximately 40 mph (64 km/h).
Driving Aids WARNINGS At all times you are responsible for controlling your vehicle, supervising the system and intervening if required. If the sensor becomes blocked the system may not function. E131359 The current assessment of your alertness indicates that you should rest as soon as safely possible. In cold and severe weather conditions the system may not function. Rain, snow, spray can all limit sensor performance.
Driving Aids Switching the System On and Off Note: The system on or off setting is stored until it is manually changed, unless a MyKey is detected. If the system detects a MyKey it defaults to on and the mode is set to Alert. Note: If a MyKey is detected, pressing the button will not affect the on or off status of the system. E144813 Press the button located on the left steering wheel stalk to switch the system on or off.
Driving Aids • • • Low Medium High • • • • System Display • Your vehicle is under the activation speed. The turn indicator is active. Your vehicle is in a dynamic maneuver. The road has no or poor lane markings in the camera field-of-view.
Driving Aids Why is the feature not available (line markings are gray) when I can see the lane markings on the road? Staying too close to the lane marking Driving at high speeds in curves Previous feature activation happened within the last one second Ambiguous lane markings (mainly in construction zones) Rapid transition from light to dark or vice versa Sudden offset in lane markings ABS or AdvanceTrac activation Camera blockage due to dirt, grime, fog, frost or water on the windshield Driving too close t
Driving Aids BLIND SPOT INFORMATION SYSTEM (If Equipped) WARNING To help avoid personal injury, NEVER use the cross traffic alert system as a replacement for using the interior and exterior mirrors and looking over your shoulder before backing out of a parking space. Cross traffic alert is not a replacement for careful driving.
Driving Aids Note: For manual transmission vehicles, the cross traffic alert will be active only if the transmission is in reverse (R). If your vehicle is rolling backward and the transmission is not in reverse (R) then cross traffic alert will not be active. E142440 In this first example, the left sensor is only partially obstructed; zone coverage is nearly maximized.
Driving Aids Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited. Note: It is possible to get a blockage warning with no blockage present; this is rare and known as a false blockage warning. A false blocked condition either self-corrects or clears after a key cycle.
Driving Aids • Reasons for messages being displayed • The radar Clean the fascia area in surface is front of the radar or remove dirty or the obstruction. obstructed The radar surface is not dirty or obstructed False Alerts Note: If your vehicle has a factory equipped tow bar and it is towing a trailer, the sensors will detect the trailer and turn the Blind Spot Information and cross traffic alert systems off to avoid false alerts.
Driving Aids You cannot switch one or both systems off when MyKey is used. See Principle of Operation (page 54). Steering Tips If the steering wanders or pulls, check for: • Correct tire pressures. • Uneven tire wear. • Loose or worn suspension components. • Loose or worn steering components. • Improper vehicle alignment. You can also have one or both systems switched off permanently at an authorized dealer. Once switched off, only an authorized dealer can switch the system back on.
Driving Aids The brake support system assists you in reducing any collision speed by pre-charging the brakes. If the risk of collision continues to increases after the audio-visual warning, the brake support prepares the brake system for rapid braking. The system does not automatically activate the brakes, but if the brake pedal is pressed even lightly, the brakes apply full stopping power. WARNINGS The Pre-Collision Assist system with brake support cannot help prevent all collisions.
Driving Aids If a blocked sensor message appears in the information display, dirt, water, or an object is blocking the sensor. The sensor is located behind a cover near the driver side of the lower grille. If anything blocks the sensor, your vehicle cannot see through the sensor, and the collision warning system will not work. Possible causes for the blocked sensor message and corrective actions are listed below.
Driving Aids • • Front Normal View: Provides an image of what is directly in front of your vehicle. Front Split View: Provides an extended view of what is in front of your vehicle. Access this view by pressing the camera button from the Front Normal View screen. DRIVE CONTROL (If Equipped) E188845 Driver Select Suspension The front view camera is located in the grille. Driver select suspension delivers a unique driving experience through a suite of sophisticated electronic vehicle systems.
Driving Aids Modes: • Comfort – Provides a more relaxed driving experience, maximizing comfort. Your steering effort decreases and the suspension movement is more fluid. Comfort mode is ideal when you desire enhanced traveling comfort. • Normal – Delivers a balanced combination of comfortable, controlled ride and confident handling. This mode provides an engaging drive experience and a direct connection to the road without sacrificing any of the composure demanded from your vehicle.
Load Carrying REAR UNDER FLOOR STORAGE Cargo Management System E142445 The system is located in the floor of the cargo area. Lift the handle to open. CARGO NETS WARNING E199571 This net is not designed to restrain objects during a collision or heavy braking. ROOF RACKS AND LOAD CARRIERS The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Repeat the attachment on both sides of the vehicle.
Load Carrying return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label: Base Curb Weight - is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment.
Load Carrying authorized-dealer installed equipment on the vehicle, you must subtract the weight of the equipment from the payload listed on the Tire Label in order to determine the new payload. WARNING The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available.
Load Carrying E142517 CARGO E143817 GAWR (Gross Axle Weight Rating) - is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver seating position. The total load on each axle must never exceed its Gross Axle Weight Rating.
Load Carrying Note: For trailer towing information refer to the RV and Trailer Towing Guide available at an authorized dealer. GVW E143818 Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver seating position. The Gross Vehicle Weight must never exceed the Gross Vehicle Weight Rating. GVW (Gross Vehicle Weight) is the Vehicle Curb Weight, plus cargo, plus passengers.
Load Carrying E142524 WARNING Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. GCW GVW E143819 GCWR (Gross Combined Weight Rating) - is the maximum allowable weight of the vehicle and the loaded trailer, including all cargo and passengers, that the vehicle can handle without risking damage.
Load Carrying Examples: For a 5000 pound (2268 kilogram) conventional trailer, multiply 5000 by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 pounds (227 to 340 kilograms). For an 11500 pound (5216 kilogram) fifth wheel trailer, multiply by 0.15 and 0.25 to obtain a proper king pin load range of 1725 to 2875 pounds (782 to 1304 kilograms). for operation at Gross Vehicle Weight Rating, not at Gross Combined Weight Rating.
Load Carrying 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lb. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lb. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400-750 (5 x 150) = 650 lb.) 5.
Load Carrying be: 635 kilograms - (2 x 99 kilograms) - (12 x 45 kilograms) = 635 - 198 - 540 = -103 kilograms. You will need to reduce the load weight by at least 240 pounds (104 kilograms). If you remove three 100-pound (45-kilogram) cement bags, then the load calculation would be:1400 - (2 x 220) - (9 x 100) = 1400 - 440 900 = 60 pounds. Now you have the load capacity to transport the cement and your friend home.
Towing Load Placement TOWING A TRAILER To help minimize how trailer movement affects your vehicle when driving: • Load the heaviest items closest to the trailer floor. • Load the heaviest items centered between the left and right side trailer tires. • Load the heaviest items above the trailer axles or just slightly forward toward the trailer tongue. Do not allow the final trailer tongue weight to go above or below 10-15% of the loaded trailer weight. • Select a tow bar with the correct rise or drop.
Towing RV & Trailer Towing Guide Online Website http://www.fleet.ford.com/towing-guides/ RECOMMENDED TOWING WEIGHTS TRAILER SWAY CONTROL (If Equipped) Note: Do not exceed the trailer weight for your vehicle configuration listed in the chart below. Note: Make sure to take into consideration trailer frontal area. Do not exceed 20 ft² (1.86 m²) for vehicles without towing package, or 30 ft² (2.79 m²) for vehicles with towing package.
Towing Your vehicle may tow a trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your vehicle configuration on the following chart. Powertrain 1 Maximum trailer weight 2 1,500 lb (680 kg) 3 3,500 lb (1,587 kg) 2.0L GTDI 2.0L GTDI 2,000 lb (907 kg) 2 2.7L GTDI 2 2,000 lb (907 kg) 3 3,500 lb (1,587 kg) 3.5L TiVCT 3.5L TiVCT 1 Calculated with SAE J2807 method. 2 Vehicle without towing package. 3 Vehicle with towing package.
Towing To connect the trailer’s safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground. ESSENTIAL TOWING CHECKS Follow these guidelines to ensure safe towing: • Do not tow a trailer until you drive your vehicle at least 1000 miles (1600 kilometers). • Consult your local motor vehicle laws for towing a trailer.
Towing Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. • • Before Towing a Trailer 1. Turn the steering wheel to point your vehicle tires away from traffic flow. 2. Set your vehicle parking brake. 3. Place the automatic transmission in position P or manual transmission in a low gear. 4. Place wheel chocks in front and back of the trailer wheels. (Chocks not included with vehicle.
Towing It is acceptable to have your front-wheel drive vehicle towed from the front if using proper wheel lift equipment to raise the front wheels off the ground. When towing in this manner, the rear wheels can remain on the ground. TRANSPORTING THE VEHICLE Front-wheel drive vehicles must have the front wheels placed on a tow dolly when towing your vehicle from the rear using wheel lift equipment. This prevents damage to the transmission.
Towing If your vehicle becomes inoperable (without access to wheel dollies or vehicle transport trailer), it can be flat-towed (all wheels on the ground, regardless of the powertrain and transmission configuration) under the following conditions: • Your vehicle is facing forward for towing in a forward direction. • Place the transmission in neutral (N). If you cannot move the transmission into neutral (N), you may need to override it. See Transmission (page 166). • Maximum speed is 35 mph (56 km/h).
Towing 3. Turn the vehicle off by turning the ignition key past the accessory position. The key position is between the accessory and off positions. See Ignition Switch (page 150). 4. Disconnect the negative (black) cable from the battery. See Changing the 12V Battery (page 269). Note: The anti-theft system does not work until you reconnect the battery cable. Follow these guidelines if you have a need for recreational (RV) towing.
Driving Hints • • BREAKING-IN You need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unusual driving characteristics. Use the recommended engine oil. Perform all regularly scheduled maintenance. There are also some things you may want to avoid doing because they reduce your fuel economy: • Avoid sudden or hard accelerations. • Avoid revving the engine before turning off the car. • Avoid long idle periods.
Driving Hints Note: Driving through standing water can cause vehicle damage. FLOOR MATS Note: Engine damage can occur if water enters the air filter. WARNINGS Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.
Driving Hints WARNINGS Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects that are loose can become trapped under the pedals causing a loss of vehicle control. Failure to properly follow floor mat installation or attachment instructions can potentially cause interference with pedal operation causing a loss of vehicle control. E142666 To install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in.
Roadside Emergencies authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km). ROADSIDE ASSISTANCE Vehicles Sold in the United States: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please refer to the coverage section of your warranty guide, call us in Canada at 1-800-665-2006, or visit our website at www.ford.ca. The hazard warning button is located on the instrument panel. Use it when your vehicle is creating a safety hazard for other motorists. • Sykes Assistance Services Corporation administers the Roadside Assistance program.
Roadside Emergencies Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle's electrical system. 3. Remove your foot from the brake pedal and press the START/STOP button to switch off the ignition. 4. You can either attempt to start the engine by pressing the brake pedal and the START/STOP button, or switch on the ignition only by pressing the START/STOP button without pressing the brake pedal. Both ways re-enable the fuel system.
Roadside Emergencies Jump Starting 1. Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000 rpms, as shown in your tachometer. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both vehicle engines for an additional three minutes before disconnecting the jumper cables.
Roadside Emergencies 2. Remove the jumper cable on the negative (-) terminal of the booster vehicle's battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the battery can recharge.
Customer Assistance These are some of the items that can be found online: • U.S. dealer locator by Dealer Name, City/State or Zip Code. • Owner Manuals. • Maintenance Schedules. • Recalls. • Ford Extended Service Plans. • Ford Genuine Accessories. • Service specials and promotions. GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer.
Customer Assistance In order to help us serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. • Your telephone number (home and business). • The name of the authorized dealer and city where located. • The vehicle’s current odometer reading. California Civil Code Section 1793.
Customer Assistance already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.
Customer Assistance In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada.
Customer Assistance FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: +971 4 3326084 Toll-Free Number of the Kingdom of Saudi Arabia: 800 8971409 Local Telephone Number of Kuwait: 24810575 FAX: +971 4 3327299 Email: menacac@ford.com www.me.ford.com Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.
Customer Assistance To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Fuses The power distribution box is located in the engine compartment. It has high-current fuses that protect your vehicle's main electrical systems from overloads. FUSE SPECIFICATION CHART Power Distribution Box WARNINGS Always disconnect the battery before servicing high-current fuses. If the battery has been disconnected and reconnected, some features will need to be reset. See Changing the 12V Battery (page 269).
Fuses Fuse or relay number Fuse amp rating 4 — 5 20A 6 — Protected components Blower motor relay. 3 Power point 3 - back of console. Not used. 7 20A 1 8 20A 1 9 — 10 20A 11 15A 12 15A Powertrain control module - vehicle power 1. Powertrain control module - vehicle power 2. Powertrain control module relay. 3 2 2 Power point 1 - driver front. Powertrain control module - vehicle power 4. Powertrain control module - vehicle power 3. 13 — Not used. 14 — Not used.
Fuses Fuse or relay number Fuse amp rating Protected components Voltage quality module (start/stop). Front split view camera. Front split view camera module. 24 10A 1 Not used (spare). 25 10A 2 Run-start anti-lock brake system. 26 10A 2 Run-start powertrain control module. 27 — 28 10A 29 — Not used. 30 — Not used. 31 — Not used. Not used. 1 Rear washer pump. 32 — Electronic fan 1 relay. 33 — A/C clutch relay. 34 15A 35 — 36 — 1 Not used (spare). Not used. Not used.
Fuses 1 Fuse or relay number Fuse amp rating Protected components 47 — Not used. 48 — Not used. 49 — Not used. 50 20A 51 — Not used. 52 — Not used. 53 — 1 Horn. 10A 55 10A Not used. 54 2 Brake on off switch. 2 ALT sensor. Micro fuse. 2 Dual micro fuse. 3 M-type fuse. Power Distribution Box - Bottom There are fuses located on the bottom of the fuse box. To access the bottom of the fuse box, do the following: E145983 1.
Fuses 3. Move the fuse box toward the center of the engine compartment. 4. Pivot the outboard side of the fuse box to access the bottom side. E190798 Fuse or relay number Fuse amp rating 56 — 57 — Protected components Not used. Not used. 1 58 30A Fuel pump feed. 59 40A 2 Electronic fan 3. 60 40A 2 Electronic fan 1. 61 — 62 50A 63 25A 64 — Not used. 2 Body control module 1. 1 Electronic fan 2. Not used.
Fuses Fuse or relay number Fuse amp rating 65 20A 66 — 1 Protected components Front heated seat. Not used. 2 67 50A Body control module 2. 68 40A 1 Heated rear window. 69 30A 1 Anti-lock brake system valves. 70 30A 1 Passenger seat. 71 — Not used. 72 20A 1 Transmission oil pump (start/stop). 73 20A 1 Rear heated seats. 74 30A 1 Driver seat module. 75 25A 1 Wiper motor 1. 76 30A 1 Power lift-gate module. 77 30A 1 Climate control seat module.
Fuses 1 Fuse or relay number Fuse amp rating 86 – 87 60A Protected components Not used. 2 Anti-lock brake system pump. M-type fuse. 2 J-type fuse. Note: It may be easier to access the fuse panel if you remove the finish trim piece. Passenger Compartment Fuse Panel The fuse panel is located under the instrument panel to the left of the steering column. E145984 Fuse or relay number 1 Fuse amp rating 10A 1 Protected components Demand lighting (glove box, vanity, dome).
Fuses Fuse or relay number Fuse amp rating Protected components Second row easy fold relay coil. 2 7.5A 3 20A 4 5A 5 20A 6 10A 7 10A 8 10A 9 10A 10 5A 2 Keypad. Power liftgate module logic power. Hands free liftgate module. 11 5A 2 Not used (spare). 12 7.5A 13 7.5A 14 10A 15 10A 16 15A 17 5A 18 5A 1 1 Memory seats. Lumbar. Power mirrors. Driver seat module logic power. Driver door unlock. Not used (spare). 1 1 Not used (spare). 2 Not used (spare).
Fuses Fuse or relay number Fuse amp rating 19 7.5A 20 7.5A 21 5A 2 Humidity and in–car temperature sensor. 22 5A 2 Occupant classification sensor. 23 10A 24 20A 25 30A 26 30A 27 30A 28 20A 29 30A 30 30A 31 15A 32 10A 33 20A 34 30A 35 5A 2 Not used (spare). 2 Active front steering logic power. 1 1 1 1 1 Protected components Delayed accessory (power inverter logic, moonroof logic, driver window switch power). Central lock unlock. Driver door (window, mirror).
Fuses 1 Fuse or relay number Fuse amp rating 36 15A 37 15A 38 30A 1 1 3 Protected components Auto-dimming rear view mirror. Heated seat. Auto high beam/lane departure mirror module. Rear heated seat module logic power. Heated steering wheel module (without active front steering). Rear power windows. Rear window switch illumination. Micro fuse. 2 Dual micro fuse. 3 Circuit breaker. CHANGING A FUSE Fuses WARNING Always replace a fuse with one that has the specified amperage rating.
Maintenance Working with the Engine Off GENERAL INFORMATION 1. Set the parking brake and shift to park (P). 2. Switch off the engine. 3. Block the wheels. Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of authorized dealers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly.
Maintenance 4. Open the hood. The hood strut automatically supports the hood. 4 Closing the Hood 1. Lower the hood and allow it to drop under its own weight for the last 8-12 in (20-30 cm). Note: Make sure that the hood is correctly closed. E191432 UNDER HOOD OVERVIEW - 2.0L ECOBOOST™ A E188729 B C D E G F I H A Engine coolant reservoir. See Engine Coolant Check (page 263). B Brake fluid reservoir (right-hand drive). See Brake Fluid Check (page 268). C Engine oil dipstick.
Maintenance G Power distribution box. See Fuses (page 248). H Air filter assembly. See Changing the Engine Air Filter (page 278). I Windshield washer fluid reservoir. See Washer Fluid Check (page 269). UNDER HOOD OVERVIEW - 2.7L ECOBOOST™ A E188730 H B G F D C J E A Engine coolant reservoir. See Engine Coolant Check (page 263). B Brake fluid reservoir. See Brake Fluid Check (page 268). C Battery. See Changing the 12V Battery (page 269). D Power distribution box. See Fuses (page 248).
Maintenance UNDER HOOD OVERVIEW - 3.5L A E188731 H B G F D C J E A Engine coolant reservoir. See Engine Coolant Check (page 263). B Brake fluid reservoir. See Brake Fluid Check (page 268). C Battery. See Changing the 12V Battery (page 269). D Power distribution box. See Fuses (page 248). E Air filter assembly. See Changing the Engine Air Filter (page 278). F Engine oil dipstick. See Engine Oil Dipstick (page 262). G Engine oil filler cap. See Engine Oil Check (page 262).
Maintenance 2. Check the oil level before starting the engine, or switch the engine off and wait 15 minutes for the oil to drain into the oil pan. 3. Remove the dipstick and wipe it with a clean, lint free cloth. Replace the dipstick and remove it again to check the oil level. ENGINE OIL DIPSTICK - 2.0L ECOBOOST™ B A If the oil level is at the minimum mark, add oil immediately. See Maintenance (page 258).
Maintenance WARNINGS Only add oil when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down. Message Hold OK to Press and hold the OK Reset button until the instrument cluster displays the following message. Do not remove the filler cap when the engine is running. Reset Successful 1. Remove the engine oil filler cap. 2. Add engine oil that meets Ford specifications. See Maintenance (page 258). 3. Wipe off any spilled oil. 4. Replace the engine oil filler cap.
Maintenance Note: During normal vehicle operation, the engine coolant may change color from orange to pink or light red. As long as the engine coolant is clear and uncontaminated, any color change does not indicate the engine coolant has degraded, nor does it require the engine coolant to be drained, the system to be flushed, or the engine coolant to be replaced. WARNINGS Do not add coolant further than the MAX mark.
Maintenance Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. If you drive in extremely hot climates: • It may be necessary to have an authorized dealer decrease the coolant concentration to 40%. • A coolant concentration of 40% provides improved overheat protection. Engine coolant concentrations below 40% decrease the freeze and corrosion protection characteristics of the engine coolant and may cause engine damage.
Maintenance 2. Tow your vehicle to an authorized dealer. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and add if low. 5. Re-start the engine and drive your vehicle to an authorized dealer. Note: Driving your vehicle without repair increases the chance of engine damage. See an authorized dealer as soon as possible. If this occurs, your vehicle still operates. However: • The engine power becomes limited. • The air conditioning system becomes disabled.
Maintenance 2. Rotate the automatic transmission fluid cap in a counterclockwise direction. See Under Hood Overview (page 261). 3. Remove the cap and dipstick and wipe it with a clean, lint-free cloth. Replace the cap and dipstick and remove it again to check the fluid level. 4. Make sure that the fluid level is between the MIN and the MAX marks. If the fluid level is at the MIN mark, add fluid immediately. See Adding Transmission Fluid. 5. Replace the automatic transmission fluid cap and dipstick.
Maintenance * Adding Transmission Fluid 1. Rotate the automatic transmission fluid cap in a counterclockwise * direction. x2 2. Remove the cap and dipstick and wipe it with a clean, lint-free cloth. 3. Add fluid that meets the Ford specifications. See Capacities and Specifications (page 335). Pour the fluid directly into the automatic transmission fluid cap and dipstick hole. 4. Replace the cap and dipstick and remove it again to check the fluid level. 5.
Maintenance WASHER FLUID CHECK WARNINGS Only use brake fluid from a sealed container. Contamination with dirt, water, petroleum products or other materials may result in brake system damage or failure. Failure to adhere to this warning could result in the loss of vehicle control, serious personal injury or death. WARNING If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection.
Maintenance To ensure proper operation of the battery management system (BMS), do not allow a technician to connect any electrical device ground connection directly to the low voltage battery negative post. A connection at the low voltage battery negative post can cause inaccurate measurements of the battery condition and potential incorrect system operation.
Maintenance 1. With the vehicle at a complete stop, set the parking brake. 2. Shift the transmission into P. 3. Turn off all accessories. 4. Step on the brake pedal and start the vehicle. 5. Run the engine until it reaches normal operating temperature. While the engine is warming up, complete the following: Reset the clock. See Audio System (page 339). Reset the power windows bounce-back feature. See Windows and Mirrors (page 88). Reset the radio station presets. See Audio System (page 339). 6.
Maintenance Changing the Rear Window Wiper Blade 1. Switch the ignition off. 2. Move the wiper arms to the service position manually. Note: You cannot move the wiper arms to the service position manually when you switch the ignition on. Note: Do not hold the wiper blade when lifting the wiper arm. Note: Make sure that the wiper arm does not spring back against the glass when the wiper blade is not attached.
Maintenance Headlamp Aiming Target E142465 4. On the wall or screen you will observe a flat zone of high intensity light located at the top of the right hand portion of the beam pattern. If the top edge of the high intensity light zone is not at the horizontal reference line, the headlamp will need to be adjusted. E142592 A 8 feet (2.4 meters). B Center height of lamp to ground. C 25 feet (7.6 meters). D Horizontal reference line. 5 Vertical Aim Adjustment Procedure 1.
Maintenance 5. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver, turn the adjuster either clockwise or counterclockwise in order to adjust the vertical aim of the headlamp. The horizontal edge of the brighter light should touch the horizontal reference line. 6. Close the hood and turn off the lamps. 5 REMOVING A HEADLAMP 1. Open the hood. See Opening and Closing the Hood (page 258). E133750 5. Disconnect the electrical connector.
Maintenance Headlamp 2. Turn the bulb counterclockwise and remove it. 3. Disconnect the electrical connector. Note: Do not touch the bulb glass. Note: You cannot separate the bulb from the bulb holder. High-Intensity Discharge Headlamps These lamps operate at a high voltage. See an authorized dealer if they fail. C E188959 A Daytime Running Lamp 1. Remove the cover. 2. Turn the bulb counterclockwise and remove it. 3. Disconnect the electrical connector. Note: Do not touch the bulb glass.
Maintenance License Plate Lamp 3. Turn the bulb holder counterclockwise and remove it. 4. Remove the bulb by pulling it straight out. 2 BULB SPECIFICATION CHART 1 3 Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized D.O.T. marking for North America to make sure they have the proper lamp performance, light brightness, light pattern, and safe visibility.
Maintenance Interior Lamps Lamp Specification Power (Watt) Interior lamp. LED LED Luggage compartment lamp. LED LED Note: LED lamps are not serviceable. See an authorized dealer if they fail.
Maintenance 3. Remove the air filter element from the air filter housing. 4. Wipe any dirt or debris from the air filter housing and cover to make sure no dirt gets in the engine and to make sure you have a good seal. 5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 6. Install the air filter housing cover. 7.
Vehicle Care GENERAL INFORMATION CLEANING THE EXTERIOR Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, we recommend Motorcraft Detail Wash.
Vehicle Care Note: Never use abrasive materials, for example steel wool or plastic pads as they can scratch the chrome surface. • Note: Do not use chrome cleaner, metal cleaner or polish on wheels or wheel covers. Exterior Plastic Parts For routine cleaning we recommend Motorcraft Detail Wash. If tar or grease spots are present, we recommend Motorcraft Bug and Tar Remover.
Vehicle Care • • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations. Cover the battery, power distribution box, and air filter assembly to prevent water damage when cleaning the engine. WARNINGS On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.
Vehicle Care Note: Follow the same procedure as cleaning leather seats for cleaning leather instrument panels and leather interior trim surfaces. See Cleaning Leather Seats (page 282). 4. If necessary, apply more soap and water solution or cleaning product to a clean, soft cloth and press it onto the soiled area. Allow this to set at room temperature for 30 minutes. 5. Remove the soaked cloth, then with a clean, damp cloth, use a rubbing motion for 60 seconds on the soiled area. 6.
Vehicle Care • • Alcohol solutions. Solvents or cleaners intended specifically for rubber, vinyl and plastics. Note: Some automatic car washes may cause damage to the finish on your wheel rims and covers. Note: Industrial-strength or heavy-duty cleaners in combination with brush agitation to remove brake dust and dirt, could wear away the clear coat finish over a period time.
Vehicle Care Engine We engineer and test all motor vehicles and their components for reliable, regular driving. Under various conditions, long-term storage may lead to degraded engine performance or failure unless you use specific precautions to preserve engine components. • • General • • • Store all vehicles in a dry, ventilated place. Protect from sunlight, if possible. If vehicles are stored outside, they require regular maintenance to protect against rust and damage.
Vehicle Care Brakes • Contact an authorized dealer if you have any concerns or issues. Make sure the brakes and parking brake release fully. Tires • Maintain recommended air pressure. Miscellaneous • • Make sure all linkages, cables, levers and pins under your vehicle are covered with grease to prevent rust. Move vehicles at least 25 ft (7.5 m) every 15 days to lubricate working parts and prevent corrosion.
Wheels and Tires Notice to utility vehicle and truck owners GENERAL INFORMATION Use only approved wheel and tire sizes, using other sizes could damage your vehicle. If you change the diameter of the tires from that fitted at the factory, the speedometer may not display the correct speed. Take your vehicle to an authorized Ford dealer to have the system reprogrammed. If you intend to change the size of the wheels from that fitted by the manufacturer, you can check the suitability with an authorized dealer.
Wheels and Tires On some four-wheel drive vehicles, the initial shift from two-wheel to four-wheel drive while the vehicle is moving can cause a momentary clunk and ratcheting sound. These sounds are normal and are not cause for concern. Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Wheels and Tires • • • Higher - to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components. Shorter - to give it the capability to approach inclines and drive over the crest of a hill without getting hung up or damaging underbody components. All other things held equal, a shorter wheelbase may make your vehicle quicker to respond to steering inputs than a vehicle with a longer wheelbase.
Wheels and Tires General Information WARNING Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. Note: Do not use the kit if you have severely damaged a tire. Only seal punctures located within the tire tread with the kit. Do not attempt to repair punctures larger than ¼ inch (6 millimeters) or damage to the tire's sidewall. The tire may not completely seal. Loss of air pressure may adversely affect tire performance.
Wheels and Tires • • • • • • • • • • • Do not remove any foreign objects, such as nails or screws, from the tire. When using the kit, leave the engine running (only if the vehicle is outdoors or in a well-ventilated area) so the compressor does not drain the vehicle's battery. Do not allow the compressor to operate continuously for more than 15 minutes. This will help prevent the compressor from overheating. Never leave the kit unattended during operation. Sealant compound contains latex.
Wheels and Tires Sealant compound contains latex. Use appropriate precautions to avoid any allergic reactions. Do not remove any foreign object that has pierced the tire. If a puncture is located in the tire sidewall, stop and call roadside assistance. 1. Remove the valve cap from the tire valve. 2. Unwrap the dual purpose hose (black tube) from the back of the compressor housing. 3. Fasten the hose to the tire valve by turning the connector clockwise. Tighten the connection securely. E175981 7.
Wheels and Tires Second Stage: Checking Tire Pressure WARNINGS If you are proceeding from the First Stage: Re-inflating the Tire with Sealing Compound and Air section and have injected sealant in the tire and the pressure is below 20 psi (1.4 bar), continue to the next step. The power plug may get hot after use and should be handled carefully while unplugging. Check the air pressure of your tires as follows: E175982 9.
Wheels and Tires 5. Unplug the hoses, re-install the valve cap on the tire and return the kit to the stowage area. What to Do After the Tire has Been Sealed After using the kit to seal your tire, you will need to replace the sealant canister. You can obtain sealant canisters and spare parts at an authorized Ford dealer. You can dispose of empty sealant canisters at home.
Wheels and Tires Installation of the sealant canister to the kit 1. With the canister held perpendicular to the housing, insert the canister nozzle into the connector and push until seated. 2. Rotate the canister 90 degrees down into the housing/casing. E175990 5. Wrap the power cord around the housing and stow the accessory power plug into its storage area. Note: If you experience any difficulties with the removal or installation of the sealant canister, consult an authorized Ford dealer for assistance.
Wheels and Tires Due to their design, low-profile tires and wheels are more prone to road damage from potholes, rough or unpaved roads, car wash rails and curb contact than standard tires and wheels. Note: Your vehicle's warranty does not cover these types of damages. Extra caution should be taken when operating on rough roads to avoid impacts that could cause wheel and tire damage. habits.
Wheels and Tires Notice to Crossover Vehicle Owners WARNING In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. All occupants must wear seat belts. Children and infants must use appropriate restraints to minimize the risk of injury or ejection. Information About Uniform Tire Quality Grading E200792 Crossover vehicles handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
Wheels and Tires Tire Quality Grades apply to new pneumatic passenger car tires. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, light truck or LT type tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104 (c)(2). U.S. Department of Transportation Tire quality grades: The U.S.
Wheels and Tires *Standard load: A class of P-metric or Metric tires designed to carry a maximum load at set pressure. For example: for P-metric tires 35 psi (2.4 bar) or 36 psi (2.5 bar) depending on tire size and for Metric tires 36 psi (2.5 bar). Increasing the inflation pressure beyond this pressure will not increase the tire’s load-carrying capability. *Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 42 psi (2.9 bar).
Wheels and Tires * B-pillar: The structural member at the side of the vehicle behind the front door. *Bead area of the tire: Area of the tire next to the rim. * Sidewall of the tire: Area between the bead area and the tread. *Tread area of the tire: Area of the perimeter of the tire that contacts the road when mounted on the vehicle. *Rim: The metal support (wheel) for a tire or a tire and tube assembly upon which the tire beads are seated.
Wheels and Tires Note: You may not find this information on all tires because it is not required by federal law. B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 65: Indicates the aspect ratio which gives the tire's ratio of height to width. D. R: Indicates a radial type tire. E. 15: Indicates the wheel or rim diameter in inches.
Wheels and Tires the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. J.
Wheels and Tires A. LT: Indicates a tire, designated by the Tire and Rim Association, that is intended for service on light trucks. B. Load Range and Load Inflation Limits: Indicates the tire's load-carrying capabilities and its inflation limits. C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual, defined as four tires on the rear axle (a total of six or more tires on the vehicle). D.
Wheels and Tires B C A C. 80: Indicates the aspect ratio, which gives the tire's ratio of height to width. Numbers of 70 or lower indicate a short sidewall. D. D: Indicates a diagonal type tire. R: Indicates a radial type tire. E. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.
Wheels and Tires (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles.
Wheels and Tires When weather temperature changes occur, tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile.
Wheels and Tires Inspecting Your Tires and Wheel Valve Stems Tire Wear Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear.
Wheels and Tires describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
Wheels and Tires WARNINGS may be found on either the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or the Tire Label which is located on the B-Pillar or edge of the driver’s door. If this information is not found on these labels then you should contact your authorized dealer as soon as possible.
Wheels and Tires The two front tires or two rear tires should generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the tire pressure monitoring system indicator is flashing, the system is malfunctioning.
Wheels and Tires Tire and Wheel Alignment Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare wheel and tire assembly it is intended for temporary use only and should not be used in a tire rotation.
Wheels and Tires USING SUMMER TIRES USING SNOW CHAINS Summer tires provide superior performance on wet and dry roads. Summer tires do not have the Mud and Snow (M+S or M/S) tire traction rating on the tire side wall. Since summer tires do not have the same traction performance as All-season or Snow tires, we do not recommend using summer tires when temperatures drop to about 40ºF (5ºC) or below (depending on tire wear and environmental conditions) or in snow and ice conditions.
Wheels and Tires • • Drive cautiously. If you hear the cables rub or bang against the vehicle, stop and re-tighten them. If this does not work, remove the cables to prevent vehicle damage. Remove the cables when you no longer need them. Do not use cables on dry roads. when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure.
Wheels and Tires Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Wheels and Tires Low tire pressure warning light Possible cause Customer action required Solid warning light Tire(s) under-inflated Make sure tires are at the proper pressure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off.
Wheels and Tires How Temperature Affects Your Tire Pressure Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full function of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. The tire pressure monitoring system monitors tire pressure in each pneumatic tire.
Wheels and Tires • 1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. • 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY. The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking performance. • Comfort and noise.
Wheels and Tires 5. Remove the steel winged washer nut securing the spare tire by turning it counterclockwise. 6. Remove the spare tire from the spare tire compartment. 7. Remove plastic wing nut and jack and lug wrench assembly. Detach lug wrench from jack by turning the jack hex nut drive screw counterclockwise. 8. Loosen each wheel lug nut one-half turn counterclockwise, but do not remove them until the wheel is raised off the ground.
Wheels and Tires 11. 12. Stowing the flat tire Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. Lower the wheel by turning the jack handle counterclockwise. You cannot store the full-sized road wheel in the temporary spare tire well. 1. Find the flat tire retainer strap tucked inside the jack channel. Lower the carpeted load floor.
Wheels and Tires E143746 6. Secure the flat tire by tying a 2-half hitch knot. TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
Wheels and Tires E145950 A Wheel pilot bore Inspect the wheel pilot hole and mounting surface prior to installation. Remove any visible corrosion or loose particles.
Capacities and Specifications ENGINE SPECIFICATIONS - 2.0L ECOBOOST™ Engine 2.0L EcoBoost Engine Cubic inches 122 Required fuel Minimum 87 octane Compression ratio 9.7:1 Spark plug gap 0.027-0.031 in. (0.70-0.80 mm) Drivebelt Routing 2.0L Ecoboost engine A B E161383 A. Long drivebelt is on first pulley groove closest to engine. B. Short drivebelt is on second pulley groove farthest from engine. ENGINE SPECIFICATIONS - 2.7L ECOBOOST™ Engine 2.
Capacities and Specifications Drivebelt Routing 2.7L EcoBoost engine E191903 ENGINE SPECIFICATIONS - 3.5L Engine 3.5L engine Cubic inches 214 Required fuel Minimum 87 octane Compression ratio 10.8:1 Spark plug gap .049-.053 in. (1.25 - 1.35 mm) Drivebelt Routing 3.
Capacities and Specifications MOTORCRAFT PARTS - 2.0L ECOBOOST™ Component 2.0L EcoBoost Engine Air filter element FA-1912 Oil filter FL-910-S Battery BXT-90T5-590 1 BAGM-48H6-760 Spark plugs SP-537 Cabin air filter FP-71 Seat filter Windshield wiper blade 1 FS-104 WW-2755 (driver side) WW-2760 (passenger side) WW-1413 (rear window) This motorcraft part is designed for vehicles with Automatic-Start-Stop. We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.
Capacities and Specifications MOTORCRAFT PARTS - 2.7L ECOBOOST™ Component 2.7L EcoBoost Air filter element FA-1912 Oil filter FL-500-S Battery BXT-90T5-590 Spark plugs SP-520 Cabin air filter FP-71 Seat filter Windshield wiper blade FS-104 WW-2755 (driver side) WW-2760 (passenger side) WW-1413 (rear window) We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance.
Capacities and Specifications MOTORCRAFT PARTS - 3.5L Component 3.5L V6 TiVCT Air filter element FA-1912 Oil filter FL-500-S Battery BXT-90T5-590 Spark plugs SP-520 Cabin air filter FP-71 Seat filter Windshield wiper blade FS-104 WW-2755 (driver side) WW-2760 (passenger side) WW-1413 (rear window) We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance.
Capacities and Specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. C Make, vehicle line, series, body type D Engine type E Check digit F Model year G Assembly plant H Production sequence number VEHICLE CERTIFICATION LABEL E142476 Please note that in the graphic, XXXX is representative of your vehicle identification number.
Capacities and Specifications The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description.
Capacities and Specifications CAPACITIES AND SPECIFICATIONS - 2.0L ECOBOOST™ Capacities WARNING The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Only qualified personnel should service the air conditioning refrigerant system. Opening the air conditioning refrigerant system can cause personal injury. Item Capacity Engine oil 5.7 qt (5.4 L) Engine coolant 8.2 qt (7.
Capacities and Specifications Specifications Materials Name Specification Recommended motor oil (U.S.): WSS-M2C946-A Motorcraft SAE 5W-30 Premium Synthetic Blend Motor Oil XO-5W30-QSP Recommended motor oil (Canada): Motorcraft SAE 5W-30 Super Premium Motor Oil CXO-5W30-LSP12 WSS-M2C946-A Recommended motor oil (Mexico): Motorcraft SAE 5W-30 Synthetic Motor Oil MXO-5W30-QSP WSS-M2C946-A Optional motor oil (U.S.
Capacities and Specifications Name Specification Automatic transmission fluid (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12 WSS-M2C938-A MERCON LV Windshield washer fluid (U.S. and Mexico): WSS-M14P19-A Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2 Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) WSS-M14P19-A A/C refrigerant (U.S.
Capacities and Specifications If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. • Longer engine cranking periods. • Increased emission levels. • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance.
Capacities and Specifications Item Capacity Engine oil 6.0 qt (5.7 L) Engine coolant 10.6 qt (10 L) Brake fluid Between MIN/MAX on brake fluid reservoir Rear differential (All Wheel Drive) fluid 2.4 pt (1.15L) Power Transfer Unit (PTU) fluid (All Wheel Drive) Automatic transmission fluid 11.0 qt (10.4 L) 1 Windshield washer fluid Fill as required Fuel tank (Front Wheel Drive) 18.4 gal (69.5 L) Fuel tank (All Wheel Drive) 18.5 gal (70 L) A/C refrigerant 21 oz (0.
Capacities and Specifications Name Specification Motorcraft SAE 5W-30 Synthetic Motor Oil CXO-5W30-LFS12 Engine coolant (U.S.
Capacities and Specifications Name Specification A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19 WSH-M17B19-A A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D WSH-M1C231-B Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5 ESB-M1C93-B Lock cylinders (U.S.
Capacities and Specifications Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure.
Capacities and Specifications Specifications Materials Name Specification Recommended motor oil (U.S.): WSS-M2C945-A Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP Recommended motor oil (Canada): Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12 WSS-M2C945-A Recommended motor oil (Mexico): Motorcraft SAE 5W-20 Synthetic Motor Oil MXO-5W20-QSP WSS-M2C945-A Optional motor oil (U.S.
Capacities and Specifications Name Specification Automatic transmission fluid (Canada): Motorcraft MERCON LV Automatic Transmission Fluid CXT-10-LV12 WSS-M2C938-A MERCON LV Windshield washer fluid (U.S. and Mexico): WSS-M14P19-A Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2 Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) WSS-M14P19-A A/C refrigerant (U.S.
Capacities and Specifications Note: Ford recommends using DOT 4 Low Viscosity (LV) High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure.
Audio System AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: • AM: 530, 540-1700, 1710 kHz • FM: 87.9-107.7, 107.9 MHz GENERAL INFORMATION Radio Frequencies and Reception Factors Radio Reception Factors Distance and strength The further you travel from an AM or FM station, the weaker the signal and the weaker the reception.
Audio System • • MP3 folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 tracks on the disc (noted by the .mp3 file extension) and all folders containing MP3 files, from F001 (folder) T001 (track) to F253 T255. Creating discs with only one level of folders helps with navigation through the disc files. AUDIO UNIT - VEHICLES WITH: AM/FM/CD/SYNC WARNING Driving while distracted can result in loss of vehicle control, crash and injury.
Audio System E144488 A CD: Press this button to listen to a CD. Press the function buttons below the radio screen to select on-screen options of Repeat or Shuffle. B SOUND: Press this button to access settings for Treble, Midrange, Bass, Fade and Balance. Use the up and down arrow buttons to select the various settings. When you make your selection, press the left and right arrow buttons to change the settings. Press OK to set or press MENU to exit.
Audio System H Seek: In radio mode, select a frequency band and press this button. The system stops at the first station up the band. Press and hold the button to move quickly to the next strong radio station or memory preset. In CD mode, press this button to select the next track. Press and hold the button to move quickly forward through the current track. I End phone call: Press this button to end a phone call. J Cursor arrows and OK: Use the up and down arrow buttons to select the various settings.
Audio System Note: Depending on your vehicle option package, your system may look different from what you see here. AUDIO UNIT - VEHICLES WITH: PREMIUM AM/FM/CD WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Audio System C TUNE: Turn to search the frequency in individual increments. D Seek: In radio mode, select a frequency and press this button. The system stops at the first station up the band. Press and hold the button to move quickly to the next strong radio station. In CD mode, press this button to select the next track. Press and hold the button to move quickly forward through the current track. E Eject: Press this button to eject a CD.
Audio System E185814 A Power: Press this button to switch the system off and on. B CD slot: Insert a CD. C Eject: Press this button to eject a CD. D - TUNE + : Press these buttons to search the frequency in individual increments. E VOL: Turn the control to adjust the volume. F Seek, Reverse and Fast Forward: In radio mode, select a frequency band and press one of these buttons. The system stops at the first station it finds in that direction.
Audio System Radio Scan Select for a brief sampling of all available channels. AST Select to store the six strongest local stations on the AMAST and FM-AST frequency bands. * Radio Text * Select to display extra information such as artist name. Extra information may not always be available. Audio Settings Speed Compensated Volume Automatically adjusts the volume to compensate for speed and wind noise. You can set the system between 0 and +7.
Audio System Display Settings Dimming Select to change display brightness. Language Select to display the language in English, French or Spanish. Temp. setting Select to display the outside temperature in Fahrenheit or Celsius. The multicast indicator appears in FM mode (only) if the current station is broadcasting multiple digital broadcasts. The highlighted numbers signify available digital channels where new or different content is available.
Audio System HD Radio Reception and Station Troubleshooting Potential reception issues Reception area If you are listening to a multicast station and you are on the fringe of the reception area, the station may mute due to weak signal strength. If you are listening to HD1, the system switches back to the analog broadcast until the digital broadcast is available again.
Audio System Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required. This is a by the radio broadcaster. broadcast issue. Sound fading or blending in The radio is shifting between No action required. The and out. analog and digital audio. reception issue may clear up as you continue to drive. * There is an audio mute delay when selecting HD2 or HD3, multicast preset or Direct Tune.
Audio System Note: This receiver includes the eCos real-time operating system. eCos is published under the eCos License. Satellite Radio Reception Factors Potential satellite radio reception issues Antenna obstructions For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other material as far away from the antenna as possible.
Audio System Troubleshooting Message Condition Action Acquiring… Radio requires more than two seconds to produce audio for the selected channel. Satellite antenna fault There is an internal module If this message does not clear shortly, or with an ignior system failure present. tion key cycle, your receiver may have a fault. See an authorized dealer for service. SIRIUS system failure No action required. This message should disappear shortly. Invalid Channel The channel is no longer available.
Audio System The auxiliary input jack allows you to connect and play music from your portable music player through your vehicle speakers. You can use any portable music player designed for use with headphones. Your audio extension cable must have male 1/8th-inch (3.5 millimeter) connectors at each end. AUDIO INPUT JACK WARNINGS Driving while distracted can result in loss of vehicle control, crash and injury.
Audio System The USB port allows you to plug in media playing devices, memory sticks and charge devices (if supported). See SYNC™ (page 354). MEDIA HUB (If Equipped) The media hub is located in front of the gearshift. A E170492 B C A Line in B USB ports C SD card slot See Entertainment (page 407).
SYNC™ GENERAL INFORMATION E142598 • SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist, Vehicle Health Report and SYNC Services (Traffic, Directions * & Information). • Use applications, such as Pandora and ** Stitcher, via SYNC AppLink. • Access phonebook contacts and music using voice commands.
SYNC™ In the United States, call 1-800-392-3673. When using SYNC: • Do not operate playing devices if the power cords or cables are broken, split or damaged. Place cords and cables out of the way, so they do not interfere with the operation of pedals, seats, compartments or safe driving abilities. • Do not leave playing devices in your vehicle during extreme conditions as it could cause them damage. See your device's manual for further information. • Do not attempt to service or repair the system.
SYNC™ System data cannot be accessed without special equipment and access to the vehicle's SYNC module. Ford Motor Company and Ford of Canada will not access the system data for any purpose other than as described absent consent, a court order, or where required by law enforcement, other government authorities, or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
SYNC™ System Interaction and Feedback The system provides feedback through audible tones, prompts, questions and spoken confirmations depending on the situation and the chosen level of interaction. You can customize the voice recognition system to provide more or less instruction and feedback. The default setting is to a higher level of interaction in order to help you learn to use the system. You can change these settings at any time.
SYNC™ Note: Make sure to switch on the ignition and the radio. Put the transmission in park (P). Changing the Voice Settings In addition to using voice commands to change the voice settings, you can also use the menu in the audio display. Using the Audio System 1. Press the MENU button. 2. Select SYNC-Settings. 3. Select Voice Settings. Note: To scroll through the menus, press the up and down arrows on your audio system. 1.
SYNC™ Phone Voice Commands Depending on your phone's capability and your market, the system may prompt you with questions, such as setting the current phone as the primary phone (the phone SYNC automatically tries to connect with first upon vehicle start-up) and downloading your phonebook. E142599 Press the voice button. When prompted, say any of the following: "PHONE" Pairing Subsequent Phones "Call " Note: Make sure to switch on the ignition and the radio. Put the transmission in park (P).
SYNC™ Making Calls Phone book commands: When you ask SYNC to access things such as a phonebook name or number, the requested information appears in the display to view. Press the phone button and say, "Call" to call the contact. Press the voice button. When prompted, say: E142599 1. Say "Call " or "Dial", then the desired number. 2. When the system confirms the number, say, "Dial" again to initiate the call.
SYNC™ Display Description and action Mic. off Turn your vehicle's microphone off. To turn the microphone on, select the option again. Privacy Switch a call from an active hands-free environment to your cellular phone for a more private conversation. When selected, the audio display indicates the call is private. Hold Put an active call on hold. When selected, the audio display indicates the call is on hold.
SYNC™ Display Description and action Dial a number Enter numbers using the audio system's numeric keypad. Phonebook Access your downloaded phonebook. 1. Press the OK button to confirm and enter. You can use the options at the bottom of the screen to access an alphabetical category quickly. You can also use the letters on the audio system's numeric keypad to jump in the list. 2. Scroll through your phonebook contacts. 3. Press the OK button again when the desired selection appears in the audio display.
SYNC™ • Select the view option to open the text message. Once selected, you have the ability to have the message read to you, to view other messages, or to select the More option. • Display If you select the More option, use the arrow button to scroll through the following options: Description and action Reply to sender Press the OK button to access, and then scroll through a list of pre-defined messages to send. Call sender Press the OK button to call the sender of the message. Forward msg.
SYNC™ Sending a Text Message Note: You can send text messages either by choosing a contact from the phonebook and selecting the text option from the audio display or by replying to a received message in the inbox. Note: You can only send a text message to one recipient at a time. 1. Select the send option when the desired selection highlights in the audio display. 2. Select the confirmation option when the contact appears. 3.
SYNC™ Display Description and action 2. Press the OK button to select a ringtone. Text msg notify Have the option of hearing an audible tone to notify you when a text message arrives. Press the OK button to turn the audible tone off or on. Phonebook pref. Modify the contents of your phonebook (such as add, delete or download). Press the OK button to select and scroll between the choices in the phonebook preferences table below. Add contacts Push the desired contacts on your cellular phone.
SYNC™ Phonebook preferences Add Pair additional phones to the system. 1. Select the option to add to start the pairing process. 2. When a message to begin pairing appears in the audio display, search for SYNC on your phone. See your phone's manual if necessary. 3. When prompted on your phone's display, enter the sixdigit PIN provided by the system in the radio display. The display indicates when the pairing is successful. 4. When the option to set the phone as primary appears, select either yes or no. 5.
SYNC™ Display Description and action Bluetooth on Check or uncheck this option to switch the system's Bluetooth interface off or on. Select this option, and then press the OK button to change the option's status. Set defaults Return to the factory default settings without erasing your indexed information (such as phonebook, call history, text messages and paired devices). Select this option and confirm when prompted in the audio display.
SYNC™ SYNC™ APPLICATIONS AND SERVICES (If Equipped) Note: The SYNC 911 Assist feature must be set on before the incident. In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone's compatibility, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • 911 Assist: Can alert 911 in the event of an emergency. • SYNC AppLink: Allows you to connect to and use certain applications such as Pandora and Stitcher (if your phone is compatible).
SYNC™ 5. Press OK when the desired option appears in the radio display. Set On or Set Off appears in the display as confirmation. Before making the call: • SYNC provides a short window of time (about 10 seconds) to cancel the call. If you fail to cancel the call, SYNC attempts to dial 911. • SYNC says the following, or a similar message: "SYNC will attempt to call 911, to cancel the call, press Cancel on your screen or press and hold the phone button on your steering wheel.
SYNC™ SYNC Mobile Apps Accessing an App's Menu The system enables voice and steering wheel control of SYNC AppLink enabled smartphone apps. Once an app is running through AppLink, you can control main features of the app through voice commands and steering wheel controls. Once an app is running through SYNC, press the right arrow button on the steering wheel control to access the app menu. Note: You must pair and connect your smartphone to SYNC to access AppLink.
SYNC™ 2. Select SyncApplications > Mobile Apps > App Settings. 3. Select the specific app or All Apps. 4. If push notifications are supported, this setting is listed. Select to enable or disable the feature as required. App Permissions App permissions are organized by groups. You can grant these group permissions individually. You can change a permission group status any time when not driving, by using the settings menu.
SYNC™ If an update is required and you want to request this update manually, for example when in a Wi-Fi hotspot, select Request Update in the settings menu. 3. You can now play music by saying any of the appropriate voice commands. See the media voice commands. Using the System Menu You can disable automatic updates by selecting Disable Updates in the settings menu. Doing so also disables the use of Mobile Apps on SYNC. 1. Plug the device into your vehicle's USB port. 2.
SYNC™ Command "Pause" "Play" Description and action Pauses device playback. Resumes device playback. "Play album " Commands inside the "< >" are dynamic, which means it could be the name of anything such as album, artist or song. This voice command is not available until indexing is complete on your device. "Play all" Play all media on the device from the first track to the last.
SYNC™ Examples of USB Commands To switch on Bluetooth audio, use the AUX or SOURCE button. You can also press the voice button and, when prompted, say, "Bluetooth audio". SYNC provides the user with many intuitive ways to find and play a song using voice. For example, if we have a song called "Penny Lane" from the album "Magical Mystery Tour" we can say the following to play this song: • • "BLUETOOTH AUDIO" "Pause" Play song "Penny Lane". Play "Penny Lane".
SYNC™ Display Description and action Shuffle Choose to have the system play your music in random order. Once you make your choice, it remains on until you switch it off. Repeat track Choose to have the system repeat the current track. Once you make your choice, it remains on until you switch it off. Similar music You can play music similar to the current type of music in the playlist.
SYNC™ 3. Select Browse USB. If there are no media files to access, the display indicates there is no media. If there are media files, you have the following options: Display Play all Description and action Play all indexed media files from your device one at a time * in numerical order. Press the OK button to select. The first track title appears in the display. Playlists Access your playlists (from formats like ASX, M3U, WPL, * or MTP). 1. Press the OK button to select. 2.
SYNC™ Display Description and action 2. Scroll to browse indexed media files on the device, and then press the OK button. Reset USB Resets the USB index. After the new indexing is complete, you can choose what to play from the USB song library. * You can use the buttons at the bottom of the audio display to jump to a certain alphabetical category quickly. You can also use the letters on the audio system's numeric keypad to jump in the list.
SYNC™ "AUDIO" "RADIO" "USB" "Preset " "What's playing" "Tune" "Help" "Help" Radio Voice Commands Sirius Satellite Radio Voice Commands If you are listening to the radio, press the voice button, and then E142599 any of the commands in the following table.
SYNC™ CD Voice Commands "CD" If you are listening to a CD, press the voice button, and then any E142599 of the commands in the following table. If you are not listening to a CD, press the voice button and, after the tone, say, "CD", and then any of the following voice commands: * "Shuffle" "Shuffle CD" "Shuffle folder" "Shuffle off" * You need to indicate to the system which track or folder to repeat or shuffle when using these commands.
SYNC™ Phone issues Issue Possible cause(s) Possible solution(s) Try turning off the device, resetting the device or removing the device's battery, then trying again. This may be a possible phone malfunction. Try pushing your phonebook contacts to SYNC by using the Add Contacts feature. Use the SYNCmyphone feature available on the website. Try pushing your phonebook contacts to SYNC by using the Add Contacts feature.
SYNC™ Phone issues Issue Possible cause(s) Possible solution(s) Try deleting your device from SYNC, deleting SYNC from your device and trying again. This may be a possible phone malfunction. Check the security and auto accept and prompt always settings relative to the SYNC Bluetooth connection on your phone. Update your device's firmware. Turn off the Auto phonebook download setting. Text messaging is not working on SYNC. This is a phone-dependent feature.
SYNC™ USB and media issues Issue Possible cause(s) Possible solution(s) SYNC does not recognize my device when I turn on the car. This is a device limitation. Make sure you are not leaving the device in your vehicle during very hot or cold temperatures. Bluetooth audio does not stream. Review the device compatibility chart on the SYNC website to confirm your This is a phone-dependent phone supports the feature. Bluetooth audio streaming function. The device is not connected.
SYNC™ Voice command issues Issue Possible cause(s) Possible solution(s) You may be using the wrong voice commands. Review the phone voice commands and the media voice commands at the beginning of their respective sections. You may be speaking too soon or at the wrong time. After pressing the voice icon, wait until after the tone sounds and Listening appears before saying a command. Any command spoken before this does not register with the system. SYNC does not understand what I am saying.
SYNC™ Voice command issues Issue Possible cause(s) Possible solution(s) Make sure you are saying the contacts exactly as they are listed. For example, if you save a contact as Joe Wilson, say "Call Joe Wilson". You may be saying the name differently than the way you saved it. Using the SYNC phone menu, open the phonebook and scroll to the name SYNC is having trouble understanding. SYNC will read the name to you, giving you some idea of the pronunciation SYNC is expecting.
SYNC™ AppLink issues Issue Possible cause(s) Possible solution(s) SYNC in order to find AppLink-capable apps on your device. iPhone users must also connect to SYNC's USB port with an Apple USB cable. Ensure you have downloaded and installed the latest version of the app from your phone's app store. Ensure the app is running on AppLink-enabled apps are your phone. Some apps My phone is connected, but not installed and running on require you to register or I still cannot find any apps. your mobile device.
SYNC™ AppLink issues Issue Possible cause(s) Possible solution(s) On an iPhone with iOS7+, to force close an app, double tab the home button then swipe up on the app to close it. Tab the home button again, then select the app again to restart it. After a few seconds, the app should then appear in SYNC's Mobile App's Menu. My Android phone is connected, my app(s) are running, I restarted them, but I still cannot find any apps.
SYNC™ AppLink issues Issue Possible cause(s) Possible solution(s) Unplug the USB cable from the phone, wait a moment, and plug the USB cable My iPhone phone is back in to the phone. After a connected, my app is The USB connection to few seconds, the app should running, I restarted the app SYNC may need to be reset. appear in SYNC's Mobile but I still cannot find it on Apps Menu. If not, "Force SYNC. Close" the application and restart it. I have an Android phone.
MyFord Touch™ (If Equipped) GENERAL INFORMATION WARNING Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible.
MyFord Touch™ (If Equipped) This system uses a four-corner strategy to provide quick access to several vehicle features and settings. The touchscreen provides easy interaction with your cellular phone, multimedia, climate control and navigation system. The corners display any active modes within those menus, such as phone status or the climate temperature. Press to select any of the following: • Driver Settings. • Recirculated Air. • Auto. • Dual. • Passenger Settings. • A/C. • Defrost.
MyFord Touch™ (If Equipped) Press to select any of the following: • AM. • FM. • SIRIUS. • CD. • USB. • BT Stereo. • SD Card. • Line In. • • Using Your Steering Wheel Controls Depending on your vehicle and option package, you can use your steering wheel controls to interact with the touchscreen system. Using the Touch Screen • To turn a feature on and off, just touch the graphic with your finger. To get the best performance from the touch-sensitive controls: • Make sure your hands are clean and dry.
MyFord Touch™ (If Equipped) Cleaning the Touchscreen Display • Use a clean, soft cloth such as one used for cleaning glasses. If dirt or fingerprints are still visible, apply a small amount of alcohol to the cloth. Do not pour or spray alcohol onto the display. Do not use detergent or any type of solvent to clean the display. • • Support The SYNC support team is available to help you with any questions you are not able to answer on your own. • Monday-Saturday, 8:30am-9:00pm EST.
MyFord Touch™ (If Equipped) Restricted features Cellular Phone Pairing a Bluetooth phone Adding phonebook contacts or uploading phonebook contacts (from a USB) List entries are limited for phone contacts and recent phone call entries System Functionality Editing the keypad code Enabling Valet Mode Editing settings while the rear view camera or active park assist are active Wi-Fi and Wireless Editing wireless settings Editing the list of wireless networks Videos, Photos and Graphics Playing video Edi
MyFord Touch™ (If Equipped) The cellular profile, media device index, and development log remain in your vehicle unless you delete them and are generally accessible only in your vehicle when the cellular phone or media player is connected. If you no longer plan to use the system or your vehicle, we recommend you perform a Master Reset to erase all stored information. court order, or where required by law enforcement, other government authorities, or other third parties acting with lawful authority.
MyFord Touch™ (If Equipped) Note: If your vehicle is not equipped with Navigation, Compass appears in the display instead of Navigation. If you press the right arrow to go into the Compass menu, you can see the compass graphic. The compass displays the direction in which the vehicle is traveling, not true direction (for example, if the vehicle is traveling west, the middle of the compass graphic displays west; north displays to the left of west though its true direction is to the right of west).
MyFord Touch™ (If Equipped) Accessing a List of Available Commands These commands can be said at any time during a voice session • "List of commands" "Main menu" • "Next page" If you use the touchscreen, press the Settings icon > Help > Voice Command List. If you use the steering wheel control, press the voice icon. After the tone, speak your command clearly.
MyFord Touch™ (If Equipped) Voice Settings To access these settings using voice commands: Voice settings allow you to customize the level of system interaction, help and feedback. The system defaults to standard interaction that uses candidate lists and confirmation prompts as these provide the highest level of guidance and feedback. • • • 1. Press the voice icon. Wait for the prompt "Please say a command". Another tone sounds to let you know the system is listening. 2.
MyFord Touch™ (If Equipped) SETTINGS A B C D E F E161968 A Clock B Display C Sound D Vehicle E Settings F Help Under this menu, you can set your clock, access and adjust the display, sound and vehicle settings as well as access settings for specific modes or the help feature. E142607 E142607 1. Press the Settings icon > Clock. 2. Press + and - to adjust the time.
MyFord Touch™ (If Equipped) The system automatically saves any updates you make to the settings. Uploading Photos for Your Home Screen Wallpaper Display Note: You cannot load photos directly from your camera. You must access the photos either from your USB mass storage device or from an SD card. You can adjust the touchscreen display through the touchscreen or by pressing the voice button on your steering wheel controls and when prompted, say, "Display settings".
MyFord Touch™ (If Equipped) When done making your selections, press Run Vehicle Health Report Now if you want your report. Sound Occupancy Mode * You can find more information on Vehicle Health Report in this chapter. See Information (page 430). Speed Compensated Volume * Your vehicle may not have these sound settings. Camera Settings This menu allows you to access settings for your rear view camera.
MyFord Touch™ (If Equipped) Settings System Access and adjust system settings, voice features, as well as phone, navigation and wireless settings. E142607 Press the Settings icon > Settings > System, then select from the following: System Language Select to have the touchscreen display in English, Spanish or French. Distance Select to display units in kilometers or miles. Temperature Select to display units in Celsius or Fahrenheit.
MyFord Touch™ (If Equipped) Voice control Interaction Mode Standard interaction mode provides more detailed interaction and guidance. Advanced mode has less audible interaction and more tone prompts. Confirmation Prompts Have the system ask you short questions if it has not clearly heard or understood your request. * Media Candidate Lists Candidate lists are possible results from your voice commands. The system simply makes a best guess at your request with these turned off.
MyFord Touch™ (If Equipped) Media player Gracenote Database Info This allows you to view the version level of the Gracenote Database. Gracenote Management With this feature on, the Gracenote Database supplies metadata information for your music files. This overrides information from your device. This feature defaults to off. Cover Art Priority With this feature on, the Gracenote Database supplies cover art for your music files. This overrides any art from your device.
MyFord Touch™ (If Equipped) Navigation Have the system automatically fill in State/Province information. Traffic Preferences Have the system display areas where roadwork occurs. Have the system display incident icons. Have the system display areas where difficult driving conditions may occur. Have the system display areas where snow and ice on the road may occur. Have the system display any smog alerts. Have the system display weather warnings.
MyFord Touch™ (If Equipped) Phone Bluetooth Devices Connect, disconnect, add or delete a device, as well as save it as a favorite. Bluetooth Turn Bluetooth on and off. Do Not Disturb Have all calls go directly to your voice mail and not ring inside your vehicle. With this feature turned on, text message notifications are also suppressed and do not ring inside your vehicle. 911 Assist Turn on or turn off the 911 Assist feature. See Information (page 430).
MyFord Touch™ (If Equipped) Wi-Fi Wi-Fi Settings Wi-Fi Network (Client) Mode turns the Wi-Fi feature on and off in your vehicle. Make sure you turn it on for connectivity purposes. Choose a Wireless Network allows you to use a previously stored wireless network. You can categorize by alphabetical listing, priority and signal strength. You can also choose to search for a network, connect to a network, disconnect from a network, receive more information, prioritize a network or delete a network.
MyFord Touch™ (If Equipped) The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
MyFord Touch™ (If Equipped) ENTERTAINMENT A B G C D E H F E161892 A AM 1 and AM AST B FM 1, FM 2 and FM AST C SIRIUS D CD E USB F Touch this button to scroll down for more options, such as SD Card, BT Stereo and Line In G These buttons change with the media mode you are in. H Radio memory presets and CD controls. Note: Some features may not be available in your area. Contact an authorized dealer for more information.
MyFord Touch™ (If Equipped) Your voice system allows you to change audio sources with a simple voice command. For example, if you are listening to music on a USB device, then want to switch to a satellite radio channel, simply press the voice button on the steering wheel controls and say the name of the SIRIUS station (such as, "the Highway").
MyFord Touch™ (If Equipped) Options Sample commands Sound Settings * "Sirius <0-223>" Touch this button to adjust settings for: "Sports games" * • • • • • • • * This command is only usable if you have an active subscription to SIRIUS satellite radio. ** The commands that have [ ] around the word means that the word is optional. For example, if you say, "Play Metallica", this is the same as the voice command, "Play [artist] ".
MyFord Touch™ (If Equipped) The multicast indicator appears in FM mode (only) if the current station is broadcasting multiple digital broadcasts. The highlighted numbers signify available digital channels where new or different content is available. HD1 signifies the main programming status and is available in analog and digital broadcasts. Other multicast stations (HD2 through HD7) are only available digitally. Direct Tune Touch this button to manually enter the desired station number.
MyFord Touch™ (If Equipped) When HD Radio broadcasts are active, you can access the following functions: • Scan allows you to hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels. You may see the HD logo appear if the station has a digital broadcast. • Memory presets allow you to save an active channel as a memory preset. Touch and hold a memory preset slot until the sound returns.
MyFord Touch™ (If Equipped) Potential station issues Issues Echo, stutter, skip or repeat in audio. Increase or decrease in audio volume. Cause Action This is poor time alignment No action required. This is a by the radio broadcaster. broadcast issue. Sound fading or blending in The radio is shifting between No action required. The and out. analog and digital audio. reception issue may clear up as you continue to drive.
MyFord Touch™ (If Equipped) "RADIO" "RADIO" "Tune" "<87.9-107.9>" 3 "Help" 1 "<87.9-107.9> HD" 1 "<530-1710>" If available. 2 If you have said "Browse", see the "Browse" chart later in this section. "AM" 3 If you have said "Tune", see the following "Tune" chart. "AM <530-1710>" "AM autoset" "AM autoset preset <#>" "TUNE" "AM preset <#>" "<530-1710>" "Browse" "<87.9-107.9>" "FM" "<87.9-107.9> HD <#>" "FM <87.9-107.9>" "AM" 2 * "FM <87.9-107.
MyFord Touch™ (If Equipped) Replay "TUNE" "HD <#>" Replay audio on the current channel. You can replay approximately 45 minutes of audio as long as you have remained tuned to the current station. Changing stations erases the previous audio. * "Preset <#>" "Help" * While in replay mode: • Press and release the seek buttons to hear the previous or next song. • Press and hold the seek buttons to reverse or fast forward in the current track. • Press play or pause to play or pause the audio.
MyFord Touch™ (If Equipped) Set Category for Seek/Scan SIRIUS Satellite Radio Information This allows you to select a category of music you would like to search for. You can then choose to either seek or scan for the stations playing that category. Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you.
MyFord Touch™ (If Equipped) Satellite Radio Electronic Serial Number (ESN) is on the System Information Screen (SR ESN:XXXXXXXXXXXX). To access your ESN, touch the bottom left corner of the touchscreen. Touch SIRIUS > Options. You need your ESN to activate, modify or track your satellite radio account.
MyFord Touch™ (If Equipped) Troubleshooting tips Radio display Cause Action No Signal. The signal is lost from the SIRIUS satellite or SIRIUS tower to your vehicle antenna. The signal is blocked. When you move into an open area, the signal should return. Updating. Update of channel programming in progress. No action required. The process may take up to three minutes. Call SIRIUS 1-888-539-7474. Your satellite service is no longer available.
MyFord Touch™ (If Equipped) CD "SIRIUS" "Tune" ** E142611 "Help" Press the lower left corner of the touchscreen, and then select the CD tab. * You can also advance and reverse the current track or current folder, if applicable. ** Repeat If you have said "Sports game", see the following "Sports game" chart. If you have said "Tune", see the following "Tune" chart. Touch this button to repeat the currently playing track, all tracks on the disc or turn the feature off if already on.
MyFord Touch™ (If Equipped) Browse SD Card Slot and USB Port Touch this button to look through all available CD tracks. SD Card Note: Your SD card slot is spring-loaded. To remove the SD card, press the card in and the system ejects it. Do not attempt to pull the card to remove it as this could cause damage. CD Voice Commands If you are listening to a CD, press the voice button on the steering E142599 wheel controls. When prompted, say any of the following commands.
MyFord Touch™ (If Equipped) More Info USB Port Touch this button to see disc information such as current track, artist name, album and genre. Options Touch this button to view and adjust various media settings. Sound Settings allows you to adjust settings for: • Bass • Midrange • Treble • Balance and Fade • DSP (Digital Signal Processing) • Occupancy Mode • Speed Compensated Volume. E175711 The USB ports are located in the center console.
MyFord Touch™ (If Equipped) You can also touch What’s Playing to hear how the system pronounces the current band and song. This can be helpful when using voice commands to make sure the system correctly plays your request. "USB" or "SD CARD" "Play podcast " "Play podcast episode " SD Card and USB Voice Commands "Play similar music" If you are listening to a USB device or an SD card, press the E142599 voice button on the steering wheel controls.
MyFord Touch™ (If Equipped) "BROWSE" "BROWSE" "TV show " "Album " * * "All albums" "Video " "All artists" "Video playlist " "All audiobooks" "Video podcast " "All authors" * This command is only available in USB mode and is device-dependent. "All folders" "All genres" Supported Media Players, Formats and Metadata Information * SYNC is capable of hosting nearly any digital media player, including iPod, Zune™, plays from device players, and most USB drives.
MyFord Touch™ (If Equipped) Bluetooth Audio Voice Commands Your auxiliary input jack allows you to play music from your portable music player over your vehicle's speakers. The jack is located in your center console. If you are listening to a Bluetooth audio device, press the voice E142599 button on the steering wheel control. When prompted, say "Next song", "Pause", "Play" or "Previous song". Press the lower left corner of the touchscreen, and then select Line In.
MyFord Touch™ (If Equipped) Troubleshooting • • • Do not connect the audio input jack to a line level output. The jack only works correctly with devices that have a headphone output with a volume control. Do not set the portable music player's volume level higher than is necessary to match the volume of the CD or FM radio as this causes distortion and reduces sound quality.
MyFord Touch™ (If Equipped) Hands-free calling is one of the main features of SYNC. Once you pair your phone, you can access many options using the touchscreen or voice commands. While the system supports a variety of features, many are dependent on your cellular phone’s functionality. The first thing you must do to use the phone features of SYNC is to pair your Bluetooth-enabled cellular phone with SYNC. This allows you to use your phone in a hands-free manner.
MyFord Touch™ (If Equipped) 2. Make sure that Bluetooth is set to On and that your cellular phone is in the proper mode. See your phone’s manual if necessary. Note: Select SYNC, and a six-digit PIN appears on your device. Ignore the call by doing nothing. SYNC logs it as a missed call. Phone Menu Options Press the top left corner on your touchscreen to select from the following options: 3. If prompted to enter a PIN on your device, it does not support Secure Simple Pairing.
MyFord Touch™ (If Equipped) Note: This is a phone-dependent feature. If your phone does not support downloading call history using Bluetooth, SYNC keeps track of calls made with the SYNC system. Composing a Text Message Messaging Note: Downloading and sending text messages using Bluetooth are phone-dependent features. Note: This is a speed-dependent feature. It is unavailable when your vehicle is traveling at speeds over 3 mph (5 km/h). Send text messages using your touchscreen.
MyFord Touch™ (If Equipped) 911 Assist Text message options Turn on or turn off the 911 Assist feature. See Information (page 430). Thanks Stuck in traffic. Phone Ringer Call me later. Select the ring tone you want to hear when you receive a call. Choose from possible system ring tones, your currently paired phone’s ring tone, a beep, text-to-speech or a silent notification.
MyFord Touch™ (If Equipped) "PHONE" "PHONE" "Pair phone" "Call" * "Privacy on" "Call " "Read text message" "Call at home" "Reply to text messages" "Call at work" "Turn ringer off" "Call on cell" "Turn ringer on" "Call on other" "Unmute call" "Call voicemail" "Help" "Dial" * This command is only available during an active call. "Do not disturb off" "Do not disturb on" ** If you say "Messages", see the following "Messages" chart for additional commands.
MyFord Touch™ (If Equipped) INFORMATION A B C D E E161889 A SYNC Services B Sirius Travel Link C Alerts D Calendar E SYNC Applications Under the Information menu, you can access features such as: • SYNC Services • Sirius Travel Link • Alerts • Calendar • SYNC Applications SYNC Services (If Equipped, United States Only) Note: SYNC Services varies by trim level and model year and may require a subscription. Traffic alerts and turn-by-turn directions available in select markets.
MyFord Touch™ (If Equipped) Note: SYNC Services requires activation before use. Visit www.SYNCMyRide.com to register and check your eligibility for complimentary services. Standard phone and message rates may apply. Subscription may be required. You must also have the active SYNC Services Bluetooth-enabled cellular phone paired and connected to the system in order to connect to, and use, SYNC Services. See Phone (page 424).
MyFord Touch™ (If Equipped) Connecting to SYNC Services Using the Touchscreen E142608 addresses by street address or by name or specific street intersections. Operator Assist is a feature of your SYNC Services subscription. For more information on Operator Assist, visit www.SYNCMyRide.com/support. 2. Follow the voice prompts to select your Destination. After the route download is finished, the phone call automatically ends. If your vehicle is equipped with Navigation, press the Information button.
MyFord Touch™ (If Equipped) SYNC Services quick tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information. You can save address points, such as work or home. You can also save favorite information like sports teams, such as Detroit Lions, or a news category. You can learn more about personalization by logging onto www.SYNCMyRide.com.
MyFord Touch™ (If Equipped) Note: A paid subscription is required to access and use these features. Go to www.siriusxm.com/travellink for more information. Weather Touch this button to view the nearby weather, current weather, or the five day forecast for the chosen area. Select Map to see the weather map, which can show storms, radar information, charts and winds. Select Area to select from a listing of weather locations. Note: Visit www.siriusxm.
MyFord Touch™ (If Equipped) "SIRIUS TRAVEL LINK" Additional sports-related voice commands "Weather map" "College football schedule" "Help" "College football scores" * If you say "Sports headlines", "Sports schedules" or "Sports scores", you can then say any of the commands in the following chart.
MyFord Touch™ (If Equipped) 911 Assist (If Equipped) Additional sports-related voice commands WARNINGS Unless the 911 Assist setting is set on before a crash, the system will not dial for help, which could delay response time, potentially increasing the risk of serious injury or death after a crash. "WNBA schedule" "WNBA scores" "Help" Do not wait for 911 Assist to make an emergency call if you can do it yourself.
MyFord Touch™ (If Equipped) • If a crash deploys an airbag, excluding knee airbags and rear inflatable safety belts where fitted or activates the fuel pump shut-off, your SYNC-equipped vehicle may be able to contact emergency services by dialing 911 through a paired and connected Bluetooth-enabled phone. You can learn more about the 911 Assist feature, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • • • See Supplementary Restraints System (page 38).
MyFord Touch™ (If Equipped) 911 Assist May Not Work If: • • • Note: Your Vehicle Health Report feature requires activation prior to use. Visit www.SYNCMyRide.com to register. There is no fee or subscription associated with Vehicle Health Report, but you must register to use this feature. Your cellular phone or 911 Assist hardware sustains damage in a crash. The vehicle's battery or the SYNC system has no power. The phones(s) previously paired or connected to the system are thrown from the vehicle.
MyFord Touch™ (If Equipped) To run a report by voice command, press the voice button on the steering wheel and, when prompted, say "Vehicle health report". information, do not run the feature or set up your Vehicle Health Report profile at www.SYNCMyRide.com. See www.SYNCMyRide.com (Vehicle Health Report Terms and Conditions, and Privacy Statement) for more information.
MyFord Touch™ (If Equipped) Touch Dual to switch separate passenger side temperature controls off and on. When you switch off Dual, the passenger side temperature changes to match the driver side temperature. Note: The passenger side temperature and the Dual indicator automatically turn on when the passenger is adjusting their temperature control. C Fan speed: Touch + or - to increase or decrease the volume of air circulated in your vehicle.
MyFord Touch™ (If Equipped) Note: To prevent window fogging, you cannot select recirculated air when MAX Defrost is on. K Driver settings: Touch the + or – to increase or decrease the air temperature on the driver side of the vehicle. Touch the heated seat icon to switch the heated seat off and on (if equipped). Touch the climate-controlled seat icon to switch the climate-controlled seat off and on (if equipped). Touch MyTemp to select your preset temperature setpoint.
MyFord Touch™ (If Equipped) "CLIMATE" "CLIMATE" "Defrost on" "Windshield floor on" "Dual off" "Help" * "Floor on" If you say "Temperature", you can then say any of the commands in the following chart. "Fan decrease" "Fan increase" "TEMPERATURE" "MAX A/C off" "<15.5-29.
MyFord Touch™ (If Equipped) Setting a Destination • Press the green corner of your touchscreen, then the Dest button when it appears. Choose any of the following: • • Destination You can cancel the route or have the system demo the route for you. Select Route Prefs to set route preferences like avoiding freeways, tollroads, ferries and car trains as well as to use or not use high-occupancy vehicle lanes. (High-occupancy vehicle lanes are also known as carpool or diamond lanes.
MyFord Touch™ (If Equipped) Main categories Shopping Entertainment & Arts Recreation & Sports Government E142634 cityseekr, when available, is a service that provides more information about certain points of interest such as restaurants, hotels and attractions. Domestic Services Subcategories Restaurant When you have selected a point of interest, the location and information appear, such as address and phone number.
MyFord Touch™ (If Equipped) Map Preferences Attraction Breadcrumbs Display your vehicle’s previously traveled route with white dots. Switch this feature ON or OFF. E142639 This icon appears when your selection exists in multiple categories within the system. Turn List Format E142640 Have the system display your turn list Top to Bottom or Bottom to Top.
MyFord Touch™ (If Equipped) Avoid These features allow you to choose to have the system avoid freeways, toll roads, ferries and car trains when planning your route. Switch these features ON or OFF. Other traffic alert features allows you to turn on certain, or all, traffic icons on the map such as road work, incident, accidents and closed roads. Scroll down to view all the different types of alerts. Switch these features ON or OFF.
MyFord Touch™ (If Equipped) Press the speaker button on the map to mute route guidance. E174017 When the light on the button illuminates, the feature is on. The speaker button appears on the map only when route guidance is active. Re-center the map by pressing this icon whenever you scroll the E146188 map away from your vehicle’s current location. E174016 Auto Zoom Change the appearance of the map display by repeatedly pressing the arrow button in the upper left corner of the screen.
MyFord Touch™ (If Equipped) Scroll cursor allows you to scroll the map; the fixed icon is in the center of the screen. The map E142647 position closest to the cursor is in a window on the top center part of the screen. No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map E142655 positioning. This icon may display under normal operation in an area with poor GPS access. Address book entry default icon(s) indicates the location on the map of an address book entry.
MyFord Touch™ (If Equipped) • • • • • Edit Turn List Detour Edit Route Preferences Edit Traffic Preferences Cancel Route. Navigation system voice commands "Destination intersection" "Destination nearest " "Destination nearest POI" Nokia is the digital map provider for the navigation application. If you find map data errors, you may report them directly to Nokia by going to http://mapreporter.navteq.com.
MyFord Touch™ (If Equipped) Navigation system voice commands "NAVIGATION" "Zoom out" "Zoom maximum" "Help" "Zoom province" These commands are only available when a navigation route is active. "Zoom state" 1 "Zoom street" 2 If you say "Destination", you can then say any command in the following "Destination" chart. "Zoom to " "Help" 3 If you say "Navigation", you can then say any command in the following "Navigation" chart.
Accessories Peace of Mind For a complete listing of the accessories that are available for your vehicle, please contact an authorized dealer or visit our online store at www.Accessories.Ford.com (United States only). • • • • • • • • • Ford Motor Company repairs or replaces any properly authorized dealer-installed Ford Original Accessory found to be defective in factory-supplied materials or workmanship during the warranty period, as well as any component damaged by the defective accessories.
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label). Ask an authorized dealer for specific weight information.
Extended Service Plan (ESP) PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRS WITH A FORD EXTENDED SERVICE PLAN. That means you get: • Reliable, quality service at any Ford or Lincoln dealership • Repairs performed by factory trained technicians, using genuine parts SERVICE PLANS (U.S. Only) More than 32 million Ford owners have discovered the powerful protection of Ford Extended Service Plan.
Extended Service Plan (ESP) SERVICE PLANS (CANADA ONLY) Avoid the Rising Cost of Properly Maintaining Your Vehicle! You can get more protection for your vehicle by purchasing a Ford Extended Service Plan. Ford Extended Service Plan is the only service contract backed by Ford Motor Company of Canada, Limited.
Scheduled Maintenance Genuine Ford and Motorcraft® Replacement Parts GENERAL MAINTENANCE INFORMATION Dealerships stock Ford, Motorcraft and Ford-authorized branded re-manufactured replacement parts. These parts meet or exceed our specifications. Parts installed at your dealership carry a nationwide 24-month or unlimited mile (kilometer) parts and labor limited warranty.
Scheduled Maintenance When the oil change message appears in the information display, it is time for an oil change. Make sure you perform the oil change within two weeks or 500 miles (800 kilometers) of the message appearing. Make sure you reset the Intelligent Oil-Life Monitor after each oil change. See Oil Change Indicator Reset (page 263).
Scheduled Maintenance Check every month Engine oil level. Function of all interior and exterior lights. Tires (including spare) for wear and proper pressure. Windshield washer fluid level. Check every six months Battery connections. Clean if necessary. Body and door drain holes for obstructions. Clean if necessary. Cooling system fluid level and coolant strength. Door weatherstrips for wear. Lubricate if necessary. Hinges, latches and outside locks for proper operation. Lubricate if necessary.
Scheduled Maintenance Multi-Point inspection Accessory drive belt(s) Hazard warning system operation Battery performance Horn operation Engine air filter Radiator, cooler, heater and air conditioning hoses Exhaust system Suspension components for leaks or damage Exterior lamps operation * Fluid levels ; fill if necessary Steering and linkage Tires (including spare) for wear and proper pressure * ** For oil and fluid leaks Windshield for cracks, chips or pits Half-shaft dust boots Washer sp
Scheduled Maintenance When to expect the OIL CHANGE REQUIRED message Interval Vehicle use and example Normal Normal commuting with highway driving No, or moderate, load or towing Flat to moderately hilly roads No extended idling 7500-10000 miles (12000-16000 km) Severe Moderate to heavy load or towing Mountainous or off-road conditions Extended idling Extended hot or cold operation 5000-7499 miles (8000-11999 km) Extreme 3000-4999 miles (4800-7999 km) Maximum load or towing Extreme hot or cold oper
Scheduled Maintenance At every oil change interval as indicated by the information display * Inspect the tires, tire wear and measure the tread depth. Inspect the wheels and related components for abnormal noise, wear, looseness or drag. * Do not exceed one year or 10000 miles (16000 kilometers) between service intervals. ** Reset the Intelligent Oil-Life Monitor after engine oil and filter changes. See Engine Oil Check (page 262).
Scheduled Maintenance Perform the services shown in the following tables when specified or within 3000 miles (4800 kilometers) of the OIL CHANGE REQUIRED message appearing in the information display. • Example 1: The OIL CHANGE REQUIRED message comes on at 28751 miles (46270 kilometers). Perform the 30000-mile (48000-kilometer) automatic transmission fluid replacement.
Scheduled Maintenance Extensive idling or low-speed driving for long distances, as in heavy commercial use (such as delivery, taxi, patrol car or livery) As required Change engine oil and filter as indicated by the information display and perform services listed in the Normal Scheduled Maintenance chart. Inspect frequently, service as required Replace cabin air filter. Replace engine air filter. Every 30000 miles (48000 Change automatic transmission fluid.
Scheduled Maintenance Exceptions Hot Climate Oil Change Intervals There are several exceptions to the Normal Schedule: Vehicles operating in the Middle East, North Africa, Sub-Saharan Africa or locations with similar climates using an American Petroleum Institute (API) Certified for Gasoline Engines (Certification mark) oil of SM or SN quality, the normal oil change interval is 3000 miles (5000 kilometers). Axle Maintenance Change the axle fluid anytime an axle is submerged in water.
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 464 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 465 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 466 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 467 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 468 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 469 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Scheduled Maintenance Repair Order #: Dealer stamp Distance: Engine hours (optional): Multi-point inspection (recommended): Signature: E146852 470 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Appendices • END USER LICENSE AGREEMENT SYNC End User License Agreement (EULA) • • You have acquired a device ("DEVICE") that includes software licensed by Ford Motor Company and its affiliates ("FORD MOTOR COMPANY") from an affiliate of Microsoft Corporation ("MS") . Those installed software products of MS origin, as well as associated media, printed materials, and "online" or electronic documentation ("MS SOFTWARE") are protected by international intellectual property laws and treaties.
Appendices • Description of Other Rights and Limitations • • • • Speech Recognition: If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is an inherently statistical process and that recognition errors are inherent in the process. Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
Appendices • • • supplements, add-on components, or Internet-based services components of the SOFTWARE after the date you obtain your initial copy of the SOFTWARE ("Supplemental Components").
Appendices • • Links to Third Party Sites: The MS SOFTWARE may provide you with the ability to link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation, their affiliates and/or their designated agent.
Appendices Adobe TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, MS, Microsoft Corporation, third party software or service providers, their affiliates or suppliers. Contains Adobe® [Flash® Player] or [AIR®] technology by Adobe Systems Incorporated. This [Licensee Product] contains [Adobe® Flash® Player] [Adobe® AIR®] software under license from Adobe Systems Incorporated, Copyright ©1995-2009 Adobe Macromedia Software LLC.
Appendices Use of Speech Recognition Functions: Speech recognition software is inherently a statistical process which is subject to errors. It is your responsibility to monitor any speech recognition functions included in the system and address any errors. WARNING Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences.
Appendices Potential Map Inaccuracy: Maps used by this system may be inaccurate because of changes in roads, traffic controls or driving conditions. Always use good judgment and common sense when following the suggested routes. Telenav may revise this Agreement and the privacy policy at any time, with or without notice to you. You agree to visit http://www.telenav.com from time to time to review the then current version of this Agreement and of the privacy policy.
Appendices 2.
Appendices COURSE OF DEALING, CUSTOM OR TRADE AND INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS WITH RESPECT TO THE TELENAV SOFTWARE. Certain jurisdictions do not permit the disclaimer of certain warranties, so this limitation may not apply to you.
Appendices the terms and conditions of this Agreement. Any such sale, assignment or transfer that is not expressly permitted under this paragraph will result in immediate termination of this Agreement, without liability to Telenav, in which case you and all other parties shall immediately cease all use of the Telenav Software. Notwithstanding the foregoing, Telenav may assign this Agreement to any other party at any time without notice, provided the assignee remains bound by this Agreement.
Appendices Agreement), and thus your use of the Telenav Software is also subject to such terms. You agree to comply with the following additional terms and conditions, which are applicable to Telenav’s third party vendor licensors: 9.2 End User Terms Required by NAV2 (Shanghai) Co., Ltd The data (“Data”) is provided for your personal, internal use only and not for resale.
Appendices Disclaimer of Liability: positioning devices or any mobile or wireless-connected electronic or computer devices, including without limitation cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or PDAs. This Data is provided to you “as is,” and you agree to use it at your own risk.
Appendices that any such export laws, rules or regulations prohibit HERE from complying with any of its obligations hereunder to deliver or distribute Data, such failure shall be excused and shall not constitute a breach of this Agreement. NOTICE OF USE CONTRACTOR (MANUFACTURER/ SUPPLIER) NAME: HERE CONTRACTOR (MANUFACTURER/ SUPPLIER) ADDRESS: c/o Nokia, 425 West Randolph Street, Chicago, Illinois 60606 Entire Agreement.
Appendices 2.
Appendices either express or implied, arising by law or otherwise, including but not limited to, effectiveness, completeness, accuracy or fitness for a particular purpose. The licensors, including Her Majesty, Canada Post and NRCan, shall not be liable in respect of any claim, demand or action, irrespective of the nature of the cause of the claim, demand or action alleging any loss, injury or damages, direct or indirect, which may result from the use or possession of the data or the Data.
Appendices A. Third Party Notices. Any and all copies of the Data and/or packaging relating thereto shall include the respective Third Party Notices set forth below and used as described below corresponding to the Territory (or portion thereof) included in such copy: Country Notice Jordan “© Royal Jordanian Geographic Centre”. The foregoing notice requirement for Jordan Data is a material term of the Agreement.
Appendices is conditioned on Client’s obtaining prior written consent from Kartografie a.s.
Appendices Sweden “Based upon electronic data © National Land Survey Sweden.” Product incorporates data which is © 20XX Telstra Corporation Limited, GM Holden Limited, Intelematics Australia Pty Ltd and Continental Pty Ltd. Switzer- “Topografische Grundlage: © land Bundesamt für Landestopographie. B. Third Party Notices for Australia.
Appendices No Other Warranty: with or in communication with any positioning devices or any mobile or wireless-connected electronic or computer devices, including without limitation cellular phones, palmtop and handheld computers, pagers, and personal digital assistants or PDAs. You agree to cease using this Data if you fail to comply with these terms and conditions.
Appendices Export Control Gracenote® Copyright You agree not to export to anywhere any part of the Data provided to you or any direct product thereof except in compliance with, and with all licenses and approvals required under, applicable export laws, rules and regulations. CD and music-related data from Gracenote, Inc., copyright© 2000-2007 Gracenote. Gracenote Software, copyright © 2000-2007 Gracenote. This product and service may practice one or more of the following U.S.
Appendices You agree that you will use the content from Gracenote ("Gracenote Content") , Gracenote Data, the Gracenote Software, and Gracenote Servers for your own personal, non-commercial use only. You agree not to assign, copy, transfer or transmit the Gracenote Content, Gracenote Software or any Gracenote Data (except in a Tag associated with a music file) to any third party.
Appendices Vehicle with SYNC only TYPE APPROVALS United States and Mexico RF Certification Logos for Tire Pressure Monitoring Sensor(s) FCC ID: KMHSG1G1 IC: 1422A-SG1G1 Schrader AG2SZ4 Numero de Registro CNC: H-13498 Mexico Model: KMHSG1P1 NOM-121-SCT1-2009 Argentina The operation of this equipment is subject to the following two conditions: (1) This equipment or device may not cause harmful interference, and (2) this equipment or device must accept any interference, including interference that may
Appendices Serbia Type Approval Number: TRC/LPD/2014/ 56 Jordon RAQP/33A/0514/S/(14-0847) Malaysia E198002 South Africa E197811 Moldova AGREE PAR L'ANRT MAROC Numéro d'agrément: MR9098 ANRT 2014 Date d'agrément: 14/03/2014 Morocco E198009 Ukraine E198001 Philippines E197844 493 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
494 Edge/Galaxy/S-MAX (CDQ), enUSA, First Printing
Index A Audible Warnings and Indicators.............98 Headlamps On Warning Chime.....................99 Key in Ignition Warning Chime........................98 Keyless Warning Alert........................................99 Parking Brake On Warning Chime.................99 A/C See: Climate Control.........................................124 About This Manual...........................................7 ABS Audio Control...................................................75 See: Brakes..................
Index Auto-Start-Stop...........................................156 Changing a Fuse...........................................257 Disabling Auto StartStop.................................157 Enabling Auto StartStop.................................156 Changing a Road Wheel............................315 Fuses.......................................................................257 Autowipers........................................................78 Auxiliary Power Points................................
Index Creating a MyKey............................................55 Electric Parking Brake..................................176 Programming/Changing Configurable Settings...............................................................55 Applying the Electric Parking brake.............176 Battery With No Charge...................................178 Parking On a Hill (Vehicles With a Manual Transmission) .................................................176 Releasing the Electric Parking Brake............
Index Flat Tire Inflation Entertainment..............................................407 See: Temporary Mobility Kit..........................288 AM/FM Radio.....................................................409 Bluetooth Audio.................................................422 Browsing Device Content...............................407 CD.............................................................................418 Line In.....................................................................
Index Getting the Services You Need...............242 Information....................................................430 Away From Home..............................................242 911 Assist...............................................................436 Alerts......................................................................436 Calendar...............................................................436 Sirius Travel Link................................................
Index Locking and Unlocking................................60 Instrument Cluster.........................................93 Instrument Lighting Dimmer.....................83 Interior Lamps.................................................85 Activating Intelligent Access............................62 Autolock ..................................................................63 Auto Relock............................................................63 Autounlock................................................
Index Motorcraft Parts - 2.0L EcoBoost™.................................................323 Motorcraft Parts - 2.7L EcoBoost™.................................................324 Motorcraft Parts - 3.5L..............................325 MyFord Touch™..........................................388 Personal Safety System™..........................37 How Does the Personal Safety System Work?...................................................................37 Phone................................................
Index Safety Belt Minder.........................................35 Refueling.........................................................160 Easy Fuel™ Capless Fuel System.................161 Belt-Minder™........................................................35 Remote Control...............................................47 Safety Belts......................................................29 Principle of Operation........................................29 Car Finder.......................................
Index Starting a Gasoline Engine.........................151 Temporary Mobility Kit..............................288 Automatic Engine Shutdown.........................153 Failure to Start.....................................................153 Guarding Against Exhaust Fumes................154 Important Ventilating Information...............154 Stopping the Engine When Your Vehicle is Moving...............................................................
Index Towing the Vehicle on Four Wheels 6-Speed Automatic Transmission 6F50/6F55..................................................232 Using All-Wheel Drive.................................170 Emergency Towing............................................232 Recreational Towing.........................................232 Using Cruise Control...................................196 Driving In Special Conditions With All-Wheel Drive (AWD)...............................170 Switching Cruise Control Off..........
Index W Using Voice Recognition...........................356 Initiating a Voice Session................................356 System Interaction and Feedback...............357 Warning Lamps and Indicators................95 Utilizing the Mediation/Arbitration Program (Canada Only)........................244 Adaptive Cruise Control....................................96 Anti-Lock Braking System................................96 Battery.....................................................................
