FORD FOCUS Owner's Manual
The information contained in this publication was correct at the time of going to print. In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation. No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2012 All rights reserved.
Table of Contents Introduction Engine immobiliser About This Manual...........................................7 Symbols Glossary.............................................7 Replacement Parts Recommendation........................................9 Principle of Operation..................................40 Coded keys.......................................................40 Arming the engine immobiliser................40 Disarming the engine immobiliser..........40 At a Glance Alarm At a Glance........
Table of Contents Removing a Headlamp................................56 Changing a Bulb..............................................57 Bulb Specification Chart.............................64 Heated Seats...................................................114 Convenience features Instrument Lighting Dimmer.....................116 Clock...................................................................116 Cigar Lighter....................................................116 Auxiliary Power Points............
Table of Contents Fuel Quality - E85........................................128 Fuel Quality - Diesel....................................128 Catalytic Converter......................................129 Fuel filler flap.................................................129 Refuelling..........................................................131 Refuelling - E85..............................................131 Fuel Consumption.........................................131 Technical Specifications..................
Table of Contents Under Bonnet Overview - 1.6L EcoBoost SCTi (Sigma)...........................................200 Under Bonnet Overview - 2.0L EcoBoost SCTi (MI4)..................................................201 Under Bonnet Overview - 2.0L Duratec-HE (MI4)...................................202 Under Bonnet Overview - 1.6L Duratorq-TDCi (DV) Diesel.................204 Under Bonnet Overview - 2.0L Duratorq-TDCi (DW) Diesel................205 Engine Oil Dipstick - 1.0L EcoBoost......
Table of Contents Tyre Care.........................................................225 Using Winter Tyres......................................225 Using Snow Chains.....................................225 Using Snow Chains - 2.0L EcoBoost SCTi (MI4)............................................................226 Tyre Pressure Monitoring System..........226 Technical Specifications............................227 Compact Disc Player Compact disc playback.............................252 Track selection.......
Table of Contents Navigation introduction General Information...................................282 Road Safety...................................................282 Navigation unit overview Navigation unit overview..........................284 Loading the navigation data...................288 Navigation Quick start Navigation Quick start...............................289 System settings System settings............................................292 Navigation system Route options menu..................
Introduction Safety alert ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it. See Owner's Manual Anti-lock braking system WARNING Avoid smoking, flames or sparks Always drive with due care and attention when using and operating the controls and features on your vehicle.
Introduction Do not open when hot Interior luggage compartment release Engine air filter Jack Engine coolant Lighting control Engine coolant temperature Low tyre pressure warning Engine oil Maintain correct fluid level Explosive gas Panic alarm Fan warning Parking aid E139213 Fasten seat belt Parking brake Front airbag Power steering fluid Front fog lamps Power windows front/rear Fuel pump reset Power window lockout Fuse compartment Service engine soon Hazard warning flashers Side a
Introduction Warranty on Replacement Parts Windscreen wash and wipe Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty. Damage caused to your vehicle as a result of the failure of non-Ford parts may not be covered by the Ford Warranty. For additional information, refer to the terms and conditions of the Ford Warranty. REPLACEMENT PARTS RECOMMENDATION Your vehicle has been built to the highest standards using quality parts.
At a Glance Front exterior overview A B C D H F G E E133220 A See Locking and Unlocking (page 33). See Keyless Entry (page 35). B See Automatic Main Beam Control (page 50). See Driver Alert (page 160). See Lane Departure Warning (page 162). See Lane Keeping Aid (page 164). See Traffic Sign Recognition (page 166). See Active City Stop (page 168). C See Changing the Wiper Blades (page 47). D See Maintenance (page 196). E See Towing Points (page 194).
At a Glance F See Changing a Bulb (page 57). G Tyre pressures. See Technical Specifications (page 227). H See Changing a Road Wheel (page 217). Vehicle interior overview A B C D E I H E133222 G F A See Transmission (page 134). B See Locking and Unlocking (page 33). C See Power Windows (page 65). See Electric exterior mirrors (page 67).
At a Glance D See Head Restraints (page 110). E See Fastening the seat belts (page 26). F See Rear Seats (page 113). G See Manual Seats (page 109). See Power Seats (page 112). H See Parking Brake (page 137). I See Opening and Closing the Bonnet (page 196).
At a Glance Right-hand drive I H G B C D E F A J E132739 P O N M L K Q R W V U T S X A Air vents. See Air Vents (page 98). B Direction indicators. See Direction Indicators (page 54). Main beam. See Lighting Control (page 49). C Left-hand drive vehicles with voice control - Information display control. See Information Displays (page 78). C Left-hand drive vehicles without voice control - Information display control. See Information Displays (page 78).
At a Glance E Left-hand drive vehicles without voice control - Audio control. See Audio Control (page 43). E Right-hand drive vehicles with voice control - Information display control. See Information Displays (page 78). E Right-hand drive vehicles without voice control - Audio control. See Audio Control (page 43). F Wiper lever. See Wipers and Washers (page 45). G Information and entertainment display. H Audio unit. See Audio unit overview (page 240). I Door lock button.
At a Glance Rear exterior overview A B C D E133221 G H A See Changing the Wiper Blades (page 47). B See Changing a Bulb (page 57). C See Changing a Bulb (page 57). D See Fuel filler flap (page 129). E See Changing a Road Wheel (page 217). F Tyre pressures. See Technical Specifications (page 227).
At a Glance G See Towing Points (page 194). H See First Aid Kit (page 183). See Warning Triangle (page 183). See Temporary Mobility Kit (page 221). Spare wheel. See Changing a Road Wheel (page 217). Jack. See Changing a Road Wheel (page 217). Wheel brace. See Changing a Road Wheel (page 217). Towing eye. See Towing Points (page 194). Fuel funnel. See Fuel filler flap (page 129).
Child Safety CHILD SEATS WARNINGS Do not leave unattended children in your vehicle. If your vehicle has been involved in an accident, have the child restraints checked by properly trained technicians. Note: Mandatory use of child restraints varies from country to country. E133140 Only child restraints certified to ECE-R44.03 (or later) have been tested and approved for use in your vehicle. A choice of these are available from your Dealer.
Child Safety Child safety seat WARNINGS Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an air bag in front of it! When using a child seat with a support leg, the support leg must rest securely on the floor. When using a child seat with a seat belt, make sure that the seat belt is not slack or twisted. CAUTION The child seat must rest tightly against the vehicle seat. It may be necessary to lift or remove the head restraint. See Head Restraints (page 110).
Child Safety Mass group categories 0 0+ Seating positions Up to 10 kg Up to 13 kg (22 lbs) (29 lbs) 1 2 3 9 - 18 kg (20 - 40 lbs) 15 - 25 kg (33 - 55 lbs) 22 - 36 kg (49 - 79 lbs) Front passenger seat with airbag ON X X UF¹ UF¹ UF¹ Front passenger seat with airbag OFF U U U U U Rear seats U U U U U X Not suitable for children in this mass group. U Suitable for universal category child seats approved for use in this mass group.
Child Safety Mass group categories 0+ 1 Rear facing Forward facing Up to 13 kg (29 lbs) 9 - 18 kg (20 - 40 lbs) Seating positions Rear centre seat Size class Not ISOFIX equipped Seat type IL Suitable for particular ISOFIX child restraints systems of the semi-universal category. Please consult child restraints systems suppliers' vehicle recommendation lists.
Child Safety Booster seat (Group 2) BOOSTER SEATS WARNINGS Do not install a booster seat or a booster cushion with only the lap strap of the seat belt. Do not install a booster seat or a booster cushion with a seat belt that is slack or twisted. Do not put the seat belt under your child’s arm or behind its back. Do not use pillows, books or towels to boost your child’s height. Make sure that your children sit in an upright position.
Child Safety Top tether anchor points - 4 door ISOFIX ANCHOR POINTS WARNING Use an anti-rotation device when using the ISOFIX system. We recommend the use of a top tether or support leg. Note: When you are purchasing an ISOFIX restraint, make sure that you know the correct mass group and ISOFIX size class for the intended seating locations. See Child Seat Positioning (page 18). Your vehicle is fitted with ISOFIX anchor points that accommodate universally approved ISOFIX child restraints.
Child Safety E87145 2. Push the child seat back firmly to engage the ISOFIX lower anchor points. 3. Tighten the tether strap in line with the child seat manufacturer's instructions. E78298 Left-hand side Turn anti-clockwise to lock and clockwise to unlock. CHILD SAFETY LOCKS Right-hand side WARNING Turn clockwise to lock and anti-clockwise to unlock. You cannot open the doors from inside if you have put the child safety locks on.
Child Safety E124779 24
Occupant protection Front airbags PRINCIPLE OF OPERATION Airbags WARNINGS Do not modify the front of your vehicle in any way. This could adversely affect deployment of the airbags. Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an airbag in front of it! E74302 Wear a seat belt and keep sufficient distance between yourself and the steering wheel.
Occupant protection Side airbags WARNINGS Never use a seat belt for more than one person. Use the correct buckle for each seat belt. Do not use a seat belt that is slack or twisted. Do not wear thick clothing. The seat belt must fit tightly around your body to achieve its optimum effect. E72658 Position the shoulder strap of the seat belt over the centre of your shoulder and position the lap strap tightly across your hips. Side airbags are fitted inside the seatback of the front seats.
Occupant protection SEAT BELT HEIGHT ADJUSTMENT E74124 E87511 Note: Lifting the slider slightly while pressing the locking button makes it easier to release the locking mechanism. To raise or lower, press the locking button on the adjuster and move as necessary. SEAT BELT REMINDER WARNING The occupant protection system will only provide optimum protection when you use the seat belt properly. E85817 Pull the belt out steadily. It may lock if you pull it sharply or if the vehicle is on a slope.
Occupant protection Rear seat belt reminder WARNING Position the seat belt correctly for your safety and that of your unborn child. Do not use only the lap strap or the shoulder strap. WARNING If multiple belts are unfastened within a few seconds of each other, only one audible chime will sound. Position the lap strap comfortably across your hips and low beneath your pregnant abdomen. Position the shoulder strap between your breasts, above and to the side of your pregnant abdomen.
Occupant protection Note: The key switch is located in the glove compartment with an airbag deactivation lamp in the overhead console. If the airbag warning lamp illuminates or flashes when you are driving, this indicates a malfunction. See Warning Lamps and Indicators (page 73). Remove the child restraint and have the system checked immediately. Disabling the passenger airbag A B E71312 A Disabled B Enabled Turn the switch to position A.
Keys and Remote Controls Note: Further remote controls may be programmed at this stage. GENERAL INFORMATION ON RADIO FREQUENCIES 4. Press any button on each additional remote control within 10 seconds of each other. CAUTIONS The radio frequency used by your remote control can also be used by other short distance radio transmissions (e.g. amateur radios, medical equipment, wireless headphones, remote controls and alarm systems).
Keys and Remote Controls Remote control without a folding key blade 1. Insert a screwdriver in the position shown and gently push the clip. 2. Press the clip down to release the battery cover. 2 1 1 E87964 1. Press and hold the pushbuttons on the edges to release the cover. Carefully remove the cover. 2. Remove the key blade. E128810 3. Carefully remove the cover. 3 E128811 4. Turn the remote control over to remove the battery. 5. Install a new battery (3V CR 2032) with the + facing upwards. 6.
Keys and Remote Controls 4. Carefully insert the screwdriver in the position shown to open the remote control. 5 E125860 CAUTION Do not touch the battery contacts or the printed circuit board with the screwdriver. 5. Carefully prise out the battery with the screwdriver. 6. Install a new battery (3V CR 2032) with the + facing downwards. 7. Assemble the two halves of the remote control. 8. Install the key blade.
Locks Double locking with the key LOCKING AND UNLOCKING Turn the key to the lock position twice within three seconds. CAUTION Check your vehicle is locked before leaving it unattended. Double locking with the remote control Press the button twice within three seconds. Note: Do not leave your keys in the vehicle. Locking Unlocking Locking with the key Unlocking with the key Turn the top of the key towards the front of the vehicle. Turn the top of the key towards the rear of the vehicle.
Locks Locking and unlocking confirmation Locking the doors individually with the key Note: If your vehicle has double locking, the direction indicators will flash once after you have activated central locking, followed by two further flashes after double locking. Note: If the central locking function fails to operate, the doors can be individually locked using the key in the position shown. When you lock the doors, the direction indicators will flash once.
Locks Locking the vehicle KEYLESS ENTRY WARNING General information The vehicle does not lock itself automatically. If the locking function is not activated, the vehicle will remain unlocked. WARNING The keyless entry system may not function if the key is close to metal objects or electronic devices such as mobile phones. Note: The ignition will automatically switch off when you lock your vehicle from the outside. This is to prevent the vehicle battery from discharging.
Locks Two short flashes of the direction indicators confirms that all the doors and the luggage compartment lid have been locked and that the alarm has been armed. Open any door. Note: A valid passive key must be located within the detection range of that door. One long flash of the direction indicators confirms that all the doors and the luggage compartment lid have been unlocked and that the alarm has been disarmed.
Locks Locking and unlocking the doors with the key blade Global opening 2 1 E87964 1 1. Carefully remove the cover. 2. Remove the key blade and insert it into the lock. Note: Only the driver's door handle is fitted with a lock cylinder. E71955 To open all the windows, press and hold the remote control unlock button for at least three seconds. Press the lock or unlock button to stop the opening function.
Locks To close all the windows, press and hold the remote control lock button for at least three seconds. Press the lock or unlock button to stop the closing function. The anti-trap function is also active during global closing. Vehicles with keyless entry E87384 WARNING Take care when using global closing. In an emergency, touch a door handle lock sensor to stop. Note: Global closing can be activated using the driver’s door handle.
Door Edge Protection 1. Insert a screwdriver in the position shown and turn the blade to gently raise the flap from the holder. 2. Remove the flap. Note: Pull out the flap holder if required when refitting. PRINCIPLE OF OPERATION Note: The protective flap may be moved gently out of position when the door is open to allow access for cleaning. Make sure that the flap is repositioned correctly otherwise the flap may not retract when you attempt to close the door. 3.
Engine immobiliser PRINCIPLE OF OPERATION The engine immobiliser is a theft protection system that prevents someone from starting the engine with an incorrectly coded key. CODED KEYS Note: Do not shield your keys with metal objects. This may prevent the receiver from recognising your key as a valid one. Note: Have all of your remaining keys erased and recoded if you lose a key. Ask your dealer for further information. Have replacement keys recoded together with your existing keys.
Alarm Battery back-up sounder PRINCIPLE OF OPERATION The battery back-up sounder is an extra alarm system which will sound a siren when the alarm is triggered. It is armed directly when you lock the vehicle. The sounder has its own battery and will sound an alarm siren even if someone disconnects the vehicle battery or the battery back-up sounder itself. Alarm system Your vehicle may be equipped with one of the following alarm systems: • • • Perimeter alarm. Perimeter alarm with interior sensors.
Alarm Note: False alarms can also be triggered by the auxiliary heater See Auxiliary Heater (page 106). If you are using the auxiliary heater, direct the air flow towards the footwell. ARMING THE ALARM Reduced guard DISARMING THE ALARM In reduced guard, the interior sensors are deactivated when you arm the alarm. Vehicles without keyless entry Note: You can set the alarm to reduced guard for the current ignition cycle only.
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING Make sure that you fully engage the locking lever when returning it to its original position. WARNING Never adjust the steering wheel when the vehicle is moving. AUDIO CONTROL Select the required source on the audio unit. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 109).
Steering Wheel Type 2 VOICE CONTROL A D C B E129463 E129464 A Volume up B Seek up or next C Volume down D Seek down or previous Pull the button to select or deselect voice control. See Voice control (page 261). Seek, next or previous Press the seek button to: • tune the radio to the next or previous stored preset • play the next or the previous track. Press and hold the seek button to: • tune the radio to the next station up or down the frequency band • seek through a track.
Wipers and Washers Automatic wiper system WINDSCREEN WIPERS Some models without autowipers are fitted with a speed-dependent front screen wiper system. D C When the vehicle is slowed to walking speed or is brought to a standstill, the wiper speed will automatically switch to the next lower wiper speed setting. B When the vehicle speed is increased, the wiper speed will return to the manually-chosen setting. Moving the wiper lever when the system is operating will switch off the system.
Wipers and Washers A WARNING B Do not operate the washer for more than 10 seconds at a time, and never when the reservoir is empty. Whilst the lever is pulled towards the steering wheel the washer will work in conjunction with the wipers. C After releasing the lever, the wipers operate for a short time.
Wipers and Washers Reverse gear wipe CHECKING THE WIPER BLADES The rear wiper will be activated automatically when selecting reverse gear if the rear wiper is not already switched on and the front wiper is operating. Rear window washer E66644 Run the tip of your fingers over the edge of the blade to check for roughness. E129194 WARNING Clean the wiper blade lips with water applied with a soft sponge.
Wipers and Washers Rear window wiper blade Service position 1. Lift the wiper arm. 3 4 E75184 2 E86456 2. Position the wiper blade at right angles to the wiper arm. 3. Disengage the wiper blade from the wiper arm. 4. Remove the wiper blade. Note: Make sure that the wiper blade locks into place. A E129986 Switch off the ignition and move the wiper lever to position A within three seconds. Release the lever when the windscreen wipers have moved to the service position. 5.
Lighting One side LIGHTING CONTROL A Lighting control positions A B C B E130139 E132706 A Off B Side and tail lamps C Headlamps A Right-hand side B Left-hand side Main and dipped beam Parking lamps WARNING Prolonged use of the parking lamps will discharge the battery. Switch off the ignition. E130140 Both sides Push the lever forward to switch between main and dipped beam. Turn the lighting control switch to position B.
Lighting Home safe lighting The headlamps will come on and go off automatically depending on the ambient light. Switch the ignition off and pull the direction indicator lever towards the steering wheel to switch the headlamps on. You will hear a short tone. The headlamps will go off automatically after three minutes with any door open, or 30 seconds after the last door has been closed. The headlamps will remain on for a period of time after you switch the ignition off.
Lighting Activating the system CAUTIONS Check and replace wiper blades regularly to ensure the camera sensor has a clear view through the windscreen. Replacement wiper blades must be the correct length. Switch on the system using the information display and autolamps. See Information Displays (page 78). See Autolamps (page 50). Note: Keep the windscreen free from obstructions such as bird droppings, insects and snow or ice.
Lighting Manually overriding the system E133632 Push or pull the lever to switch between main and dipped beam. E132709 Note: This is a temporary override and the system will return to automatic operation after a short period. REAR FOG LAMPS WARNINGS Only use the rear fog lamps when visibility is restricted to less than 50 metres (164 feet). To permanently deactivate the system use the information display menu or turn the lighting control switch from autolamps to headlamps.
Lighting ADJUSTING THE HEADLAMPS - VEHICLES WITH: ADAPTIVE FRONT LIGHTING/XENON HEADLAMPS 2 To adjust the headlamps for driving on the left or right hand side of the road, see your dealer. 2 1 HEADLAMP LEVELLING Note: Vehicles with Xenon headlamps are equipped with automatic headlamp levelling. 1. E132711 2. Rotate the button to the required setting. 3. Push the button to the closed position. Press to release the pop out button.
Lighting Note: Tap the lever up or down to make the direction indicators flash only three times.
Lighting The cornering lamps illuminate the inside of a corner when you are turning. If you press switch B all lamps remain off when the door is opened. Press the switch again to reverse. INTERIOR LAMPS You can control all lamps using switch C. Interior lighting Centre mounted lamp Note: Individual lamps may be switched on independently, but not off if all lamps have been switched on by the driver.
Lighting Type 1 1. Ambient lighting illuminates several areas, for example footwells, cup holders and doors with a single colour and can be switched on and off using the information display menu. See General Information (page 78). Open the bonnet. See Opening and Closing the Bonnet (page 196). 2 Use the instrument lighting dimmer switches to adjust to the desired brightness. See Instrument Lighting Dimmer (page 116). 4 Type 2 2 3 E133215 2. Remove the screws. 3.
Lighting Note: When fitting the headlamp, make sure that you reconnect the electrical connector properly. A B C D Note: When fitting the headlamp, make sure that you fully engage the headlamp in the lower fixing point. Note: When fitting the headlamp, make sure that the screw is located in the headlamp moulding before you install it. E133102 CHANGING A BULB WARNINGS Switch the lights and the ignition off. Let the bulb cool down before removing it.
Lighting Headlamp main beam 2 4 CAUTION Do not touch the glass of the bulb. 1. Remove the headlamp. See Removing a Headlamp (page 56). 2 4 E133106 2. Remove the cover. 3. Disconnect the electrical connector. 4. Release the clip and remove the bulb. E133105 Side Lamp 2. Remove the cover. 3. Disconnect the electrical connector. 4. Release the clip and remove the bulb. 1. Remove the headlamp. See Removing a Headlamp (page 56). 3 Headlamp dipped beam CAUTION Do not touch the glass of the bulb.
Lighting Side repeater 1 E133426 1. Carefully remove the cover. E133109 4. Remove the bulb holder. 5. Remove the bulb. Approach lamp CAUTION When removing the mirror glass, take care not to break it. Note: Position the mirror glass as far inwards as possible. E133427 2. Using a suitable implement release the retaining clip. E133108 E133110 3. Carefully remove the side repeater.
Lighting 1. Insert your fingers into the gap between the mirror housing and the mirror glass and pull gently to remove the mirror glass. 3 2 E133717 2. Remove the lamp. 2 E133107 E133718 3 Note: You cannot separate the fog lamp bulb from the bulb holder. 3. Remove the bulb. 2. Disconnect the electrical connector. 3. Turn the bulb holder anti-clockwise and remove it. Front fog lamps 1. Remove the headlamp. See Removing a Headlamp (page 56). Rear lamps - 5 door E133111 1.
Lighting A B 2 C D E133112 E133113 2. Remove the wing nuts and detach the clip. 3. Remove the lamp. 5. Remove the bulb holder. 6. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it. A. Brake lamp B. Reversing lamp C. Tail and fog lamp D. Direction indicator 4 Rear lamps - 4 door Direction indicator, tail and fog lamp E133127 4. Disconnect the electrical connector. E133702 1. 61 Remove the trim panel.
Lighting 6. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it. A. Tail and fog lamp B. Direction indicator Brake and reversing lamp 1. 2 Open the luggage compartment lid. x10 2 E133703 2. Remove the wing nuts and detach the clip. 3. Remove the lamp. E133724 2. Remove the luggage compartment lid trim. 4 E133713 3 4. Disconnect the electrical connector. B E133725 E133714 CAUTION A Unclip the outboard side first. 5. Remove the bulb holder.
Lighting Number plate lamp 3. Remove the wing nut and detach the 2 clips. 4. Remove the lamp. Note: These are not serviceable items, please consult your dealer if they fail. Interior lamps Vehicles with LED lamps Note: The LED board is not a serviceable item, please consult your dealer if this fails. 5 E133726 5. Disconnect the electrical connector. B E125092 Luggage compartment lamp, footwell lamp and tailgate lamp A E133727 6. Remove the bulb holder. 7.
Lighting BULB SPECIFICATION CHART Lamp Specification Power (watt) PY21W 21 Headlamp main beam H1 55 Headlamp dipped beam H7 55 Cornering lamp H1 55 Front fog lamp H11 55 W5W 5 Front direction indicator Side lamp Side repeater WY5W 5 W5W 5 Rear direction indicator PY21W 21 Brake and tail lamp P21/5W 21/5 Approach lamp 1 1 Tail lamp W5W 5 Rear fog lamp P21W 21 Reversing lamp W16W 16 Luggage compartment lamp W5W 5 Fit a replacement with the same rating as the one y
Windows and Mirrors POWER WINDOWS Opening and closing the windows automatically WARNING Press or lift the switch to the second action point and release it completely. Press or lift it again to stop the windows. Do not operate the electric windows unless they are free from obstruction. Safety switch for rear windows Note: If you operate the switches often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating.
Windows and Mirrors 3. Lift the switch again for one more second. 4. Push and hold the switch until the window is fully open. 5. Release the switch. 6. Lift and hold the switch until the window is fully closed. 7. Open the window and try to close it automatically. 8. Reset and repeat procedure if the window does not close automatically. The electric windows will stop automatically while closing and reverse some distance if there is an obstacle in the way.
Windows and Mirrors The mirrors will fold automatically when you lock the vehicle with the key, the remote control or a keyless entry system request. The mirrors will unfold when you unlock the vehicle with the key, the remote control, a keyless entry system request, the driver's interior door handle or starting the engine. ELECTRIC EXTERIOR MIRRORS Manual folding and unfolding A C The electric folding mirrors operate with the ignition on.
Windows and Mirrors AUTO-DIMMING MIRROR A A E71028 E124788 The auto-dimming mirror will adjust automatically when hit by glaring light from behind. It will not work when you have selected reverse gear. Using the system The system displays a yellow indicator located in the exterior mirrors. BLIND SPOT MONITOR Blind spot information system (BLIS) WARNINGS The system is not designed to prevent contact with other vehicles or objects.
Windows and Mirrors Note: Vehicles that pass through the blind zone quickly (typically less than 2 seconds) will not trigger the alert. False alerts Note: False alerts are temporary and will self correct. The system consists of two radar sensors each located behind the rear wheels hidden behind the bumpers. There may be certain instances when the system will alert with no vehicle present in the blind zone. CAUTIONS Do not place items such as bumper stickers in this area.
Windows and Mirrors Blocked sensor WARNING Prior to the system recognizing a blocked condition and issuing a warning, the number of missed objects will increase. CAUTION The sensors may not detect vehicles in heavy rain or other conditions that cause disruptive reflections. Note: Keep the rear bumper area surrounding the sensors free from dirt, ice and snow. If a sensor becomes blocked the system performance may degrade. A blocked sensor message may be displayed.
Instrument Cluster GAUGES Type 1 A F E D C E132065 A Information display. See Information Displays (page 78).
Instrument Cluster Type 2 and 3 A E D C B E130149 A Information display. See Information Displays (page 78). B Speedometer C Engine coolant temperature gauge D Fuel gauge E Tachometer 2.0L EcoBoost - MI4 A B Engine coolant temperature gauge C All vehicles Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the centre section.
Instrument Cluster Indicates the temperature of the engine oil. If the engine oil pressure drops below the normal range, the oil pressure gauge pointer will drop into the red section of the gauge scale and the engine oil pressure warning lamp in the main instrument cluster will illuminate. Stop the vehicle as soon as safely possible and switch off the engine immediately. Check the oil level and add oil if needed. See Engine Oil Check (page 207).
Instrument Cluster Airbag warning lamp Engine warning lamp If it illuminates when you are driving, this indicates a malfunction. Have the system checked by a properly trained technician. If it illuminates with the engine running, this indicates a malfunction. If it flashes when you are driving, reduce the speed of your vehicle immediately. If it continues to flash, avoid heavy acceleration or deceleration. Have the system checked by a properly trained technician immediately.
Instrument Cluster Message indicator Glow plug indicator See Starting a Diesel Engine (page 121). It will illuminate when a new message is stored in the information display. See Information Messages (page 86). Headlamp indicator Oil pressure warning lamp It will illuminate when you switch the headlamp dipped beam or the side and tail lamps on. CAUTION Do not resume your journey if it illuminates despite the level being correct. Have the system checked by a properly trained technician immediately.
Instrument Cluster Stability control (ESP) indicator 4. Highlight Information or Warning and press the OK button to switch the chime on and off. 5. Press the left arrow button to exit the menu. Press and hold the left arrow button to return to the main menu display. While driving, it flashes during activation of the system. After switching on the ignition, if it does not illuminate or illuminates continuously while driving, this indicates a malfunction. During a malfunction, the system switches off.
Instrument Cluster Low fuel A warning chime will sound when the remaining fuel is less than approximately 6 litres (1.3 gallons). Seat belt reminder See Seat belt reminder (page 27).
Information Displays GENERAL INFORMATION Phone Note: The information display will remain on for several minutes after you switch off the ignition. Settings Various systems on your vehicle can be controlled using the information display controls on the steering column. Corresponding information is displayed in the information display. Controls Press the up and down arrow buttons to scroll through and highlight the options within a menu.
Information Displays Trip Computer Trip odometer Dist to empty Instant fuel Average fuel Ford EcoMode Gear shifting Anticipation Speed Ford EcoMode Average speed Outside air All values Information Seatbelts Auto StartStop Driver Alert Traffic signs Settings Driver assist Traction ctrl ESC BLIS City Stop Forward alert Driver alert Hill start assist Deflation detection Traffic signs Lane departure Auto light rain Ambient light Dimming Lighting Auto highbeam Hdlamp delay A B E133367 79 On Spor
Information Displays A B Display Navigation info Always on On demand Always off Language English Deutsch Italiano Français Español Čeština Dansk Norsk Pyccкий Nederlands Polski Svenska Português Measure unit l/100km Miles/Gallon Temp unit °Celsius °Fahrenheit Chimes Park slot found Information Warning Convenience Aux heater Park heater Alarm System check E133368 80 Time 1 Time 2 Once Heat now Full guard Reduced Ask on exit
Information Displays Menu structure - information and entertainment display You can access the menu using the buttons on the audio or navigation unit.
Information Displays Menu structure - information and entertainment display You can access the menu using the Information and entertainment display control. For item location: See At a Glance (page 10).
Information Displays Vehicles with navigation system Navigation Active guidance Route sections list Route Block next section Unblock rt sectn Country City/postcode Destination input Street District Start guidance TA TMC messages Traffic Block next section Route sections list Unblock rt sectn Start guidance Change address Home address Last destinations Favourites Favourites A-Z Points of interest POIs nearby Near destination Along motorway POIs near address Search by name New tour Stored tours To
Information Displays A B C Eco settings Trailer Roof box Dynamic Motorway Tunnel Ferry/motorail Toll Seasonal roads Toll sticker Special functions GPS info System info Enter position Demo mode CD See separate menu structure Radio See separate menu structure Auxiliary See separate menu structure Phone See separate menu structure Menu Navigation Route options Map display B C E130535 84 Route Driver Eco Settings Dynamic Motorway Tunnel Ferry/motorail Toll Seasonal roads Toll sticker Map
Information Displays B C Assistance options Signs/lanes Speed limits Nav icons in lists Hazard spot warning Personal data Clear last destination Clear favourites Delete home address Clear all Reset all settings Audio Settings Clock Settings See separate menu structure See separate menu structure E130536 Outside air temperature TRIP COMPUTER Shows the outside air temperature. Trip Odometer Odometer Registers the mileage of individual journeys. Registers the total mileage of the vehicle.
Information Displays Measure units To toggle between metric and imperial units, scroll to this display and press the OK button. Toggling the units of measure using this display will affect the following displays: • Distance to empty. • Average fuel consumption. • Instantaneous fuel consumption. • Average speed. Temperature units E130248 To toggle between metric and imperial units, scroll to this display and press the OK button.
Information Displays Active City Stop Message Indicator Active City Stop Sensor blocked Clean screen amber Active City Stop not available amber Active City Stop Auto braking - Action See (page 168). See (page 168). See (page 168). Airbag Message Airbag malfunction service now Message indicator amber Action Have the system checked by a properly trained technician as soon as possible.
Information Displays Battery and charging system Message Electrical system over voltage stop safely Battery low check handbook Message indicator Action red Stop your vehicle as soon as it is safe to do so and switch off the ignition. Have the system checked by a properly trained technician as soon as possible. amber Have the system checked by a properly trained technician as soon as possible.
Information Displays Cruise control and Adaptive cruise control (ACC) Message Indicator Action Front radar sensor blocked check handbook amber Forward Alert not available amber ACC not available amber See Adaptive cruise control (ACC) (page 154). Message indicator Action See Adaptive cruise control (ACC) (page 154). See Adaptive cruise control (ACC) (page 154). Doors open Message Driver door open red Stop the vehicle as soon as safely possible and close.
Information Displays Engine immobiliser Message Message indicator Action Immobiliser active check handbook amber Your key has not been recognised. Remove the key and try again. Immobiliser malfunction service required amber Have the system checked by a properly trained technician as soon as possible. Hill start assist Message Hill start assist not available Message indicator amber Action Have the system checked by a properly trained technician.
Information Displays Lane keeping aid Message Lane keeping aid malfunction Service required Indicator amber Action Have the system checked by a properly trained technician as soon as possible. Lighting Message Message indicator Headlamp malfunction service required amber Action Have the system checked by a properly trained technician as soon as possible. Brake lamp bulb fault - One or both of the brake lamp bulbs have blown. Check the brake lamp bulbs. See Changing a Bulb (page 57).
Information Displays Maintenance Message indicator Action High engine temperature stop safely red Stop your vehicle as soon as it is safe to do so and switch off the ignition. Have the system checked by a properly trained technician as soon as possible. Brake fluid level low service now red Check the brake fluid level. See Brake and Clutch Fluid Check (page 209). Engine malfunction service now red Stop the vehicle as soon as safely possible and switch off the engine immediately.
Information Displays Parking brake Message Indicator Action Park brake applied red See Parking Brake (page 137). Park brake applied amber See Parking Brake (page 137). Power steering Message Message indicator Action Steering lock malfunction stop safely red Stop your vehicle as soon as it is safe to do so and switch off the ignition. Have the system checked by a properly trained technician as soon as possible. red Stop your vehicle as soon as it is safe to do so and switch off the ignition.
Information Displays Starting the engine Message Ford KeyFree switch ignition off press POWER Message indicator red Action See Keyless Starting (page 121). Drive to clean exhaust filter check handbook amber See Diesel Particulate Filter (page 123). Engine malfunction service now amber See Diesel Particulate Filter (page 123). Press brake to start - See Keyless Starting (page 121). Press clutch to start - See Keyless Starting (page 121).
Information Displays Start-stop Message Message indicator Action Auto StartStop Switch ignition off red Switch the ignition off before leaving the vehicle if the system has shut down the engine. See Using start-stop (page 125). Auto StartStop malfunction service required amber Have the system checked by a properly trained technician. Auto StartStop Press clutch to start engine - The engine needs to be restarted, press the clutch pedal to start. See Using start-stop (page 125).
Information Displays Transmission Message indicator Action Transmission too hot press brake red Under certain driving conditions it is possible that the clutches in the transmission can overheat. In these circumstances it is necessary to press the brake pedal and stop the vehicle to prevent further overheating. Select N (NEUTRAL) or P (PARK) and apply the foot brake and parking brake until the transmission has cooled and the message disappears from the display.
Information Displays Message indicator Action Transmission not in Park select P - See Automatic Transmission (page 134). See Starting and Stopping the Engine (page 119). To start press brake - See Automatic Transmission (page 134). See Starting and Stopping the Engine (page 119). Press brake pedal - See Automatic Transmission (page 134). Message Tyre pressure monitoring system Message Message indicator Action Check tyre pressures amber The pressure in one or more tyres has dropped.
Climate Control Warming the interior PRINCIPLE OF OPERATION Direct the air towards your feet. In cold or humid weather conditions, direct some of the air towards the windscreen and the door windows. Outside air Keep the air intakes forward of the windscreen free from obstruction (snow, leaves etc.) to allow the climate control system to function effectively. Cooling the interior Direct the air towards your face.
Climate Control Side air vent MANUAL CLIMATE CONTROL Air distribution control B C D E132996 E A E74660 A Face level B Face level and footwell C Footwell D Footwell and windscreen E Windscreen You can set the air distribution control to any position between the symbols.
Climate Control Blower Ventilation A E129885 Set the air distribution control, blower and air vents to suit your requirements. Air conditioning Switching the air conditioning on and off E75470 A Off Note: If you switch the blower off, the windscreen may mist up. If you turn the blower off, the air conditioning will turn off. When you turn the blower on again, the air conditioning will come on automatically.
Climate Control With the heater control in this position, the air conditioning and recirculated air will switch on automatically. If you move the air distribution control to a position other than windscreen, the A/C will remain on. You can switch the air conditioning and recirculated air on and off.
Climate Control To switch mono mode off Note: Avoid adjusting the settings when the vehicle interior is extremely hot or cold. The automatic climate control adjusts to the current circumstances automatically. For the system to function properly, the side and centre vents should be fully open. Select a temperature for the passenger’s side with the rotary control on the passenger’s side. Mono mode will switch off and MONO disappears from the display.
Climate Control Air distribution The blower speed and the temperature control operate automatically and cannot be adjusted manually. The blower is set to high speed and the temperature to HI. To adjust air distribution, press the desired button. Any combination of settings can be selected simultaneously. A B When you select windscreen defrosting and demisting, the heated screens switch on automatically and switch off after a short time. To return to auto mode, press the AUTO button.
Climate Control When switched off, the heating, ventilation and air conditioning system is switched off and recirculated air is selected. ELECTRIC SUNROOF WARNING Before operating the electric sunroof you should verify it is free of obstructions and ensure that children and/or pets are not in the proximity of the sunroof opening. Failure to do so could result in serious personal injury.
Climate Control Opening and closing the sunroof To open or close the sunroof automatically press either side of the switch to the second action point and release it completely. Press again to stop. When the closed position is reached, the sunroof stops automatically. Sunroof anti-trap protection WARNINGS The anti-trap function is deactivated until the memory has been reset. Careless closing of the window can cause injuries.
Climate Control Sunroof safety mode AUXILIARY HEATER WARNING Parking heater The anti-trap function is not active during this procedure. Make sure that there are no obstacles in the way of the closing sunroof. WARNINGS The parking heater must not be operated at filling stations, near sources of combustible vapours or dust or in enclosed spaces. If the system detects a malfunction, it enters a safety mode. The sunroof will move for only about 0.5 seconds at a time and then stop again.
Climate Control • • • It preheats the interior of the vehicle. It keeps the windows clear of ice in the event of frost and prevents condensation. It avoids cold starts and allows the engine to reach operating temperature sooner. Park Heater Time 1 Time 2 Once Heat now To prevent the battery from discharging: • • Once the parking heater has performed one heating cycle, the next programmed heating cycle will only be carried out if you have started the vehicle’s engine in between.
Climate Control 1. 2. 3. 4. 5. 6. 7. Fuel operated heater (depending on country) Use the arrow buttons on the steering wheel to enter the main menu. Select the first programme time list. Highlight the day on which the heater should warm up the vehicle. Press the OK button. Continue in the same way to select all the days on which the heater should warm up the vehicle. To set the time at which the vehicle should be warmed up, highlight the time at the top of the display and press the OK button.
Seats • SITTING IN THE CORRECT POSITION • bend your legs slightly so that you can press the pedals fully. position the shoulder strap of the seat belt over the centre of your shoulder and position the lap strap tightly across your hips. Make sure that your driving position is comfortable and that you can maintain full control of your vehicle. MANUAL SEATS Moving the seats backwards and forwards E68595 WARNINGS Do not adjust the seats when the vehicle is moving.
Seats Adjusting the lumbar support Adjusting the angle of the seatback E78058 E130250 Adjusting the height of the driver’s seat HEAD RESTRAINTS WARNINGS Raise the rear head restraint when the rear seat is occupied by a passenger. Do not remove the front head restraints when the front seats are in use. When using a forward facing child restraint on a rear seat, always remove the head restraint from that seat.
Seats Removing the head restraints Rear outer head restraints Front head restraints E135437 2 Press the locking button and remove the head restraint. 1 Rear inner head restraint E140447 Press locking button 1 and at the same time release the retaining clip 2 using a suitable implement. E135401 Press the locking buttons and remove the head restraint.
Seats POWER SEATS - VEHICLES WITH: 6-WAY POWER SEATS E78060 POWER SEATS - VEHICLES WITH: 8-WAY POWER SEATS E141827 112
Seats Adjust the length of the seat cushion 1 1 2 E135629 1. Press and hold the unlock buttons. 2. Push the seatback forwards. E78816 Press the locking handle underneath the cushion extension and slide the extension forward or backward. 3 REAR SEATS WARNINGS When folding the seatbacks down and up, take care not to get your fingers caught between the seatback and seat frame. E135628 Make sure that the seats and the seatbacks are secure and fully engaged in their catches.
Seats Folding the seat cushions and the rear seatbacks forwards WARNINGS Make sure the red indicator is not showing when you engage the seat in the catches. 4 Lower the head restraints. See Head Restraints (page 110). When inserting your fingers between the seat cushion and seatback, take care not to get your fingers caught on the ISOFIX anchor points and bracket. See ISOFIX Anchor Points (page 22). E135647 2 Note: Make sure that the seat belt is fully tightened into the retractor. 2 4.
Seats E130471 The maximum temperature is reached after five or six minutes. It is regulated thermostatically. The seat heating will operate only when the ignition is on.
Convenience features INSTRUMENT LIGHTING DIMMER E132415 Press the element in to use the cigar lighter. It will pop out automatically. E132712 AUXILIARY POWER POINTS Press repeatedly or press and hold until the desired level is reached. CAUTION Note: If the battery is disconnected, discharged, or a new battery is installed, the dimmer will set the illuminated components to the maximum setting automatically. If you use the socket when the engine is not running, the battery may discharge.
Convenience features CUP HOLDERS WARNING Do not place hot drinks in the cup holders when the vehicle is moving. Rear seat armrest E91508 CHILDMINDER MIRROR E132505 GLASSES HOLDER E75192 AUXILIARY INPUT SOCKET You can find the socket in the glove box or the centre console. See Auxiliary input (AUX IN) socket (page 255). E75193 USB PORT You can find the socket in the glove box or the centre console. See Connectivity (page 277).
Convenience features SATELLITE NAVIGATION UNIT HOLDER Adjusting the holder 1 3 2 E112711 1. Unlock. 2. Adjust the holder to the desired position. 3. Lock. Note: Make sure that the navigation unit holder is locked in position. FLOOR MATS WARNING When using the floor mats, always make sure the floor mat is properly secured using the appropriate fixings and positioned so that it does not interfere with the operation of the pedals.
Starting and Stopping the Engine II The ignition is switched on. All electrical circuits are operational. Warning lamps and indicators illuminate. This is the key position when driving. You must also select it when being towed. GENERAL INFORMATION General points on starting If the battery has been disconnected the vehicle may exhibit some unusual driving characteristics for approx. 8 kilometres (5 miles) after reconnecting the battery. III The starter motor is activated.
Starting and Stopping the Engine STARTING A PETROL ENGINE Flooded engine Note: You can only operate the starter for a limited period of time, for example 10 seconds. The number of start attempts is limited to approximately six. If you exceed this limit, the system will not allow you to try again until a period of time has elapsed, for example 30 minutes. Vehicles with manual transmission 1. Fully depress the clutch pedal. 2. Fully depress the accelerator pedal and hold it there. 3. Start the engine.
Starting and Stopping the Engine Starting at low ambient temperatures If the battery has been disconnected or after the fuel type has been changed, the idle speed may be irregular. This will improve after 10 to 30 seconds. When the temperature is lower than -10°C (14°F) and the vehicle is filled with E85, an engine block heater should be used to facilitate starting. See Engine Block Heater (page 124). Failure to do this will result in a non start.
Starting and Stopping the Engine 2. Move the transmission selector lever to position P or N. 3. Briefly press the button. WARNINGS Always check that the steering wheel lock is deactivated before attempting to move your vehicle. See Steering Wheel Lock (page 119). Starting a diesel engine Note: Engine cranking may not commence until the engine glow plug cycle has been completed. This may take several seconds in extremely cold conditions.
Starting and Stopping the Engine Stopping the engine when the vehicle is moving WARNING Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not be locked, but higher effort will be required. When the ignition is switched off some electrical circuits, warning lamps and indicators may also be OFF. Press and hold the button or press twice within two seconds. E85767 2. Insert the key into the key holder.
Starting and Stopping the Engine Note: After you have switched your engine off the fans may continue to run for a short period of time. ENGINE BLOCK HEATER CAUTION Unlike a normal filter which requires periodic replacement, the DPF has been designed to regenerate, or clean itself to maintain operating efficiency. The regeneration process takes place automatically. However, some driving conditions mean that you may need to support the regeneration process.
Start-Stop Note: If you stall the engine, and then depress the clutch pedal within a couple of seconds, the system will automatically restart the engine. PRINCIPLE OF OPERATION CAUTION For vehicles with Start-stop the battery requirement is different. It must be replaced by one of exactly the same specification as the original. Note: The Start-stop indicator will illuminate green when the engine shuts down. See Warning Lamps and Indicators (page 73).
Start-Stop • • • • Low engine operating temperature. Low brake system vacuum. If a road speed of 5 km/h (3 mph) has not been exceeded. The driver's seat belt has not been fastened. To re-start the engine Note: The gear lever must be in the neutral position. Depress the clutch pedal. The system may automatically restart the engine under certain conditions, for example: • • Low battery voltage. To maintain the interior climate.
Eco Mode Anticipation PRINCIPLE OF OPERATION Adjusting your vehicle speed and the distance to other vehicles without the need for heavy braking or acceleration will improve fuel consumption. The system assists the driver to drive more efficiently by constantly monitoring characteristics of gear changing, anticipation of traffic conditions and speeds on motorways and open roads. Efficient speed Note: These efficiency values do not result in a defined fuel consumption figure.
Fuel and Refuelling SAFETY PRECAUTIONS CAUTIONS Do not use leaded petrol or petrol with additives containing other metallic compounds (e.g. manganese-based). They could damage the emission system. WARNINGS Stop refuelling after the fuel nozzle stops the second time. Additional fuel will fill the expansion space in the fuel tank which could lead to fuel overflowing. Fuel spillage could be hazardous to other road users. Do not use methanol instead of E85.
Fuel and Refuelling CAUTIONS Use diesel that meets the specification defined by EN 590, or the relevant national specification. CAUTIONS Do not push-start or tow-start your vehicle. Use booster cables. See Jump-Starting the Vehicle (page 215). Note: We recommend that you use only high quality fuel. Do not switch the ignition off when driving. Note: The use of additives or other engine treatments not approved by Ford is not recommended.
Fuel and Refuelling Type 2 WARNING Stop refuelling after the fuel nozzle stops the second time. Additional fuel will fill the expansion space in the fuel tank which could lead to fuel overflowing. Fuel spillage could be hazardous to other road users. A E135935 1. Press the flap to open it. Open the flap fully until it engages. B E139203 A A Incorrect position B Correct position 3. Do not lift the nozzle during refilling.
Fuel and Refuelling Type 2 REFUELLING CAUTION Do not attempt to start the engine if you have filled the fuel tank with the incorrect fuel. This could damage the engine. Have the system checked by a properly trained technician immediately. REFUELLING - E85 CAUTION Do not attempt to start the engine if you have filled the fuel tank with the incorrect fuel. This could damage the engine. Have the system checked by a properly trained technician immediately. E139205 4.
Fuel and Refuelling TECHNICAL SPECIFICATIONS Focus Fuel Consumption Figures Urban Extra-Urban Combined CO2 Emissions l/100 km (mpg) l/100 km (mpg) l/100 km (mpg) g/km 5.9 (47.9) 4.1 (68.9) 4.8 (58.9) 109 6 (47.1) 4.2 (67.3) 4.9 (57.6) 112 1.0L EcoBoost (92kW/125PS), 5-door 6.3 (44.8) 4.2 (67.3) 5 (56.5) 114 1.0L EcoBoost (92kW/125PS), 4-door and estate 6.4 (44.1) 4.4 (64.2) 5.1 (55.4) 117 1.6L Duratec-16V Ti-VCT, 5door, vehicles with manual transmission 8 (35.3) 4.7 (60.1) 5.
Fuel and Refuelling Urban Extra-Urban Combined CO2 Emissions l/100 km (mpg) l/100 km (mpg) l/100 km (mpg) g/km 9.1 (31) 4.9 (57.6) 6.4 (44.1) 156 2.0L EcoBoost - MI4 9.9 (28.5) 5.6 (50.4) 7.2 (39.2) 169 1.6L Duratorq-TDCi, vehicles without start-stop 5.7 (49.6) 3.7 (76.3) 4.5 (62.8) 117 1.6L Duratorq-TDCi, vehicles with start-stop 5.1 (55.4) 3.7 (76.3) 4.2 (67.3) 109 2.0L Duratorq-TDCi - DW, vehicles with manual transmission 6.3 (44.8) 4.2 (67.3) 5 (56.5) 129 2.
Transmission MANUAL TRANSMISSION AUTOMATIC TRANSMISSION Selecting reverse gear Selector lever positions CAUTION Do not engage reverse gear when the vehicle is moving. This can cause damage to the transmission. E133124 E99067 On some vehicles it is necessary to raise the collar whilst selecting reverse gear. Vehicles with 5-speed transmission CAUTION Fully depress the clutch pedal and wait for three seconds before you select reverse gear.
Transmission WARNINGS Apply the parking brake and select park before leaving your vehicle. Make sure that the selector lever is latched in position. The transmission will select the appropriate gear for optimum performance based on ambient temperature, road gradient, vehicle load and driver input. Note: An audible warning will sound if you open the driver's door and you have not selected park.
Transmission Moving off 1. Release the parking brake. 2. Release the brake pedal and press the accelerator pedal. 4 Stopping 1. Release the accelerator pedal and press the brake pedal. 2. Apply the parking brake. 3. Select neutral or park. E133129 Note: The lever is white. Kickdown 4. Apply the brake pedal. Using a suitable tool press and hold the lever forward while pulling the selector lever out of the park position and into the neutral position.
Brakes The ABS will not eliminate the risks when: • you drive too close to the vehicle in front of you • the vehicle is aquaplaning • you take corners too fast • the road surface is poor. PRINCIPLE OF OPERATION Note: Depending on applicable laws and regulations in the country for which your vehicle was originally built, the brake lamps may flash if you brake heavily. Note: Occasional brake noise is normal and often does not indicate a concern.
Stability Control PRINCIPLE OF OPERATION Stability control (ESP) warning lamp Electronic stability programme (ESP) The ESP warning lamp will flash when the system is operating. See Warning Lamps and Indicators (page 73). WARNING Emergency brake assist ESP does not relieve you of your responsibility to drive with due care and attention. WARNING Emergency brake assist does not relieve you of your responsibility to drive with due care and attention.
Stability Control USING STABILITY CONTROL 2.0L ECOBOOST SCTI (MI4) WARNING If you switch stability control off, active city stop will also be switched off. Note: The system will be switched on automatically every time you switch the ignition on. Note: You can also turn the system off and on using the information display. See General Information (page 78). The switch is located in the instrument panel. See At a Glance (page 10).
Hill Start Assist PRINCIPLE OF OPERATION WARNINGS At all times you are responsible for controlling the vehicle, supervising the system and intervening, if required. The system makes it easier to pull away when the vehicle is on a slope without the need to use the parking brake. When the system is active, the vehicle will remain stationary on the slope for a short time after you release the brake pedal. During this time, you have time to move your foot from the brake to the accelerator pedal and pull away.
Hill Start Assist • • • Wait for a short time until the system deactivates automatically. If a forward gear was selected when the system became active, select reverse gear. If reverse gear was selected when the system became active, select a forward gear.
Parking Aids Note: The outer sensors may detect the side walls of a garage. If the distance between the outer sensor and the side wall remains constant for three seconds, the tone will switch off. As you continue, the inner sensors will detect rearward objects. PRINCIPLE OF OPERATION WARNING The system does not relieve you of your responsibility to drive with due care and attention.
Parking Aids A E130180 E130178 A A trailer symbol indicates there is a trailer attached and the system is disabled. Distance Indicator. As the distance decreases the indicator moves towards the vehicle. PARKING AID - VEHICLES WITH: FRONT AND REAR PARKING AID A continuous tone will start at a distance of less than 30 centimetres (11 inches) to the rear bumper.
Parking Aids Manoeuvring with the parking aid A You will hear an alternating tone from the front and rear if obstacles are closer than 30 centimetres (11 inches) to the front and rear bumpers. B 1 A D C 2 E130382 A E130381 1 Reverse gear selected 2 Neutral or forward gear selected A Display and tone B Display and tone C Display only D Display and tone Distance Indicator. As the distance decreases the indicator moves towards the vehicle.
Parking Aids E130180 A trailer symbol indicates there is a trailer attached and the rear sensors are disabled.
Rear view camera PRINCIPLE OF OPERATION The camera is a visual aid for use when reversing. WARNING The system does not relieve you of your responsibility to drive with due care and attention. CAUTIONS If you use a high pressure spray to wash your vehicle, only spray the camera briefly from a distance not less than 20 centimetres (8 inches). E99105 Activating the rear view camera Do not apply pressure to the camera. CAUTION The camera may not detect objects that are close to the vehicle.
Rear view camera Using the display D CAUTIONS Obstacles above the camera position will not be shown. Inspect the area behind your vehicle if necessary. E D C C B B A A Marks are for general guidance only, and are calculated for vehicles in maximum load conditions on an even road surface. The lines show a projected vehicle path (based on the current steering wheel angle) and the distance from the exterior mirrors and rear bumper. E99458 147 A Exterior mirror clearance - 0.
Rear view camera D Green - 0.6 - 0.9 metre (24 - 35 inches) E Amber - centre line of the projected vehicle path Note: The green line is extended from 0.9 metre (35 inches) up to a distance of 3.2 metres (126 inches). Note: When reversing with a trailer, the lines on the screen are not shown. The camera will show the vehicle direction and not the trailer. Deactivating the rear view camera Note: Disengage reverse gear. The display will stay on for a short period before switching off.
Active Park Assist The system will detect a suitable parallel parking space and steer the vehicle into the space. The system controls the steering while the driver controls the accelerator, transmission and brakes. The manoeuvre can be stopped at any time by holding the steering wheel or pressing the active park assist switch. See At a Glance (page 10). PRINCIPLE OF OPERATION WARNINGS The system does not relieve you of your responsibility to drive with due care and attention.
Active Park Assist Move forwards at a maximum speed of 30 km/h (18 mph). Press the active park assist switch. See At a Glance (page 10). Use the direction indicator lever to select searching either to the left-hand side or right-hand side of the vehicle. Note: If no selection is made via the direction indicator lever the system will default to the passenger side of the vehicle. A E130107 Note: To disable the chimes: See Personalised Settings (page 85).
Active Park Assist You can take control of the manoeuvre by holding the steering wheel. A message may appear that the system can be resumed. To accept this message press the active park assist switch. See At a Glance (page 10). E130109 Move the vehicle forwards. Stop the vehicle when you hear a continuous tone. Repeat the above steps until the vehicle is satisfactory parked. The display will indicate when the system has finished the manoeuvre.
Cruise Control Setting a speed PRINCIPLE OF OPERATION Press the SET+ switch or the SET- switch to store and maintain your current speed. The cruise control indicator will illuminate. See Warning Lamps and Indicators (page 73). WARNING The system does not relieve you of your responsibility to drive with due care and attention. Changing the set speed Cruise control allows you to control your speed using the switches on the steering wheel.
Cruise Control Note: The system will no longer control your speed. The cruise control indicator will not illuminate but the system will retain the speed that you previously set. Resuming the set speed Pull the RES switch. The cruise control indicator will illuminate and the system will attempt to resume the speed that you previously set. Switching cruise control off E130072 The system will not retain the speed that you previously set. The cruise control indicator will not illuminate.
Adaptive cruise control (ACC) Note: When adaptive cruise control is activated, you may hear some unusual sounds during automatic braking. This is normal and caused by the automatic braking system. PRINCIPLE OF OPERATION WARNINGS The system is not a collision warning or avoidance system. The separate forward alert function provides a collision warning and mitigation feature. See Forward alert function (page 158). You must intervene if the system does not detect a vehicle in front.
Adaptive cruise control (ACC) Detection beam issues Automatic braking with ACC WARNINGS You must take immediate action once alerted, as the adaptive cruise control braking will not be sufficient to keep a safe distance to the vehicle in front. In some cases there may be no warning or the warning may be delayed. You should always apply the brakes when necessary. When following a vehicle in front of you, adaptive cruise control will not automatically decelerate to a stop.
Adaptive cruise control (ACC) Changing the set speed USING ADAPTIVE CRUISE CONTROL Note: Vehicle speed may be increased and decreased at intervals of 5 km/h or 5 mph. The system is operated by adjustment controls mounted on the steering wheel. Note: If the system does not react to these changes the reason may be that the gap interval to the vehicle in front prevents an increase in speed.
Adaptive cruise control (ACC) The distance between you and the vehicle detected in front is maintained by a variable setting. There are five steps which are represented by horizontal bars displayed in the information display. One bar indicates the smallest gap and five bars indicates the largest gap. These bars are shown empty when in standby mode and filled when in active mode. Press the brake pedal or pull switch F to cancel the system.
Adaptive cruise control (ACC) • • • • Note: The collision alerts will only occur if the system is switched on, however the brake support is always on and cannot be turned off. brake temperature being too high, for example when driving on mountainous or hilly roads engine speed being too low radar sensor being covered parking brake being applied. Note: The system may be used with or without the Adaptive cruise control system being activated.
Speed Limiter Switching the system on and off PRINCIPLE OF OPERATION Press switch B. The information display will prompt for a speed to be set. WARNING When you are going downhill, your speed may increase above the set speed. The system will not apply the brakes but a warning will be given. Setting the speed limit Use the cruise control switches to alter the maximum speed setting. Press switch A or switch C to select your desired speed limit.
Driver Alert Note: Keep the windscreen free from obstructions such as bird droppings, insects and snow or ice. PRINCIPLE OF OPERATION WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. Note: The system is intended as a driver aid when driving on fast main roads and motorways. Note: The system calculates an alertness level at vehicle speeds above approximately 65 km/h (40 mph).
Driver Alert System display Resetting the system When active the system will run automatically in the background and only issue warnings if required. You can view the status at any time using the information display. See General Information (page 78). You can reset the system by either: • Switching the ignition off and on. • Stopping the vehicle and then opening and closing the driver's door. The alertness level is shown by six steps as a coloured bar.
Lane Departure Warning Note: The system is intended as a driver aid when driving on fast main roads and motorways. PRINCIPLE OF OPERATION WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. Note: The system may not operate during hard braking or acceleration and, when you are intentionally steering the vehicle. Note: The system will operate with a minimum of one tracked lane marking.
Lane Departure Warning The lane markings are colour coded as follows: • Green - The system is ready to warn you of any unintentional lane departure. • Red - The vehicle is approaching or is too close to the detected lane boundary. Take immediate safe action to reposition the vehicle. • Grey - The relevant lane boundary will be suppressed. Activate and deactivate the system using the button on the indicator stalk. Press the button to turn the system off. Press the button twice to turn the system on.
Lane Keeping Aid Note: Keep the windscreen free from obstructions such as bird droppings, insects and snow or ice. PRINCIPLE OF OPERATION WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. Note: The system is intended as a driver aid when driving on fast main roads and motorways. Note: The system may not operate during hard braking or acceleration and when you are intentionally steering the vehicle.
Lane Keeping Aid • • E132099 Activate and deactivate the system using the button on the indicator stalk. Red - The vehicle is approaching or is too close to the detected lane boundary. A warning is given in the form of a vibration felt through the steering wheel. Take immediate safe action to reposition the vehicle. Grey - The relevant lane boundary will be suppressed. Instances where a lane boundary may be suppressed: • Lane markings on the road may not be detected by the sensor.
Traffic Sign Recognition The system will automatically detect recognizable traffic signs, for example speed limit signs, no overtaking signs and speed limit cancellation signs. PRINCIPLE OF OPERATION WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. USING TRAFFIC SIGN RECOGNITION At all times you are responsible for controlling the vehicle, supervising the system and intervening if required.
Traffic Sign Recognition 3. After a predetermined distance they will be shown greyed out. 4. After another predetermined distance they will be deleted. If a supplementary traffic sign is detected, for example a reduced speed limit in wet road conditions sign, it will not be shown but will appear as an empty box underneath the respective sign.
Active City Stop PRINCIPLE OF OPERATION WARNINGS If the engine stops after the system has been activated, the hazard warning flashers will be activated. WARNINGS The system does not relieve you of your responsibility to drive with due care and attention. The system may not function when driving around sharp curves. At all times you are responsible for controlling the vehicle, supervising the system and intervening if required.
Active City Stop Switching the system on and off Note: The system is per default on. Note: In certain situations, it may be advisable to disable the system, for example driving off road when objects may cover the windscreen. Activate and deactivate the system using the information display. See General Information (page 78). USING ACTIVE CITY STOP 2.0L ECOBOOST SCTI (MI4) WARNINGS Never look directly into the sensor with any type of object, there is a risk of eye injury.
Load Carrying GENERAL INFORMATION WARNINGS Use load securing straps to an approved standard, e.g. DIN. Make sure that you secure all loose items properly. Place luggage and other loads as low and as far forward as possible within the luggage or loadspace. Do not drive with the tailgate or rear door open. Exhaust fumes may enter the vehicle. E97377 LUGGAGE ANCHOR POINTS Do not exceed the maximum front and rear axle loads for your vehicle. See Vehicle identification (page 232).
Load Carrying To install the cargo retention net cassette: Remove the luggage cover. Push the sliders on the cassette towards each other and insert the telescopic bar into the holes on the sidewall behind the rear seatbacks. Ensure that the end caps with the anti-rotation pin are correctly fitted in the side trim. E72969 Pull out the cover and secure it in the retaining points. Release it from the retaining points and let it roll back into the case. Clip the retaining hook onto the case.
Load Carrying Installing behind the front seats Reinstall the luggage cover. Remove in the reverse order. Cargo net A B E86848 1. Push the ends of the bar on the grille towards each other and insert them into the retainers on the roof. Push the bar forwards into the narrow section of the retainers. E78835 A With retaining rings B Without retaining rings The cargo net can be used to prevent objects sliding around.
Load Carrying 1. Push the ends of the bar on the grille towards each other and insert them into the retainers on the roof. Push the bar forwards into the narrow section of the retainers. E87783 3. Attach the grille to the lower bar with the handwheels. Do not tighten the handwheels. 4. Tighten the screws at the lower anchor points. 5. Tighten the handwheels. Installing behind the rear seats E104424 2. Remove two screws from both the luggage anchor points. See Luggage Anchor Points (page 170). 3.
Load Carrying Note: The side mounting tracks are designed such that crossbars (for bicycle carriers, ski carriers etc.) from the Ford accessories range can be fitted. ROOF RACKS AND LOAD CARRIERS Roof rack Note: Before installing the crossbars, clean the side mounting tracks with water and a sponge. WARNINGS If you use a roof rack, the fuel consumption of your vehicle will be higher and you may experience different driving characteristics. Note: Position the crossbars as shown.
Load Carrying 4 Nm 4 2 4Nm 7 3 E135138 2. Insert the key. Turn the key anti-clockwise. 3. Remove the cover. 4. Loosen the screws. A A E135139 Note: Make sure there is no gap between crossbar and rail(A). 6. Install the crossbars. 7. Tighten the screws until you hear a distinct click. 8. Install the cover. Turn the key clockwise to lock. 9. Remove the key. B Installing a roof box E135140 E135141 5. Install rubber strips in the positions shown.
Towing Change down a gear before you reach a steep downhill gradient. TOWING A TRAILER WARNINGS The Focus ECOnetic is not approved for trailer towing. TOWING A TRAILER - 2.0L ECOBOOST SCTI (MI4) Do not exceed 100 km/h (62 mph). WARNING Your vehicle is not approved for trailer towing. The rear tyre pressures must be increased by 0.2 bar (3 psi) above specification. See Technical Specifications (page 227).
Towing Releasing the tow ball arm CAUTION Do not touch the tow ball arm during the release process. Note: If the release process is interrupted, for example an obstacle in the way or loss of power supply, the system will need to be reset. To reset the system, repeat the release process. E139284 Note: The lamp in the switch illuminates when the system is activated. The tow ball arm automatically swivels into the lowered position.
Towing Swivelling the tow ball arm in Fault conditions If the tow ball arm release button is illuminated or you hear a warning tone when the ignition switch is in position II, repeat the release process. CAUTION Before swivelling the tow ball arm in, always unhitch the trailer or dismantle load carriers and their attachments. Dismantle attachments for tracking stabilisation. Remove the plug for the trailer power supply and the adapter from the socket. Failure to do so may result in damage to the bumper.
Towing Unlocking the tow ball arm mechanism TOW BALL WARNINGS When not in use, always transport the tow ball arm securely fastened in the luggage compartment. 3 Take special care when fitting the tow ball arm as the safety of the vehicle and the trailer depends on 1 this. Do not use any tools for mounting or dismounting the tow ball arm. Do not modify the trailer coupling. Do not disassemble or repair the tow ball arm. 2 E71329 1. Remove the protecting cap (1).
Towing Inserting the tow ball arm Driving with a trailer A 1 B E71331 WARNING If any of the below conditions cannot be met, do not use the tow bar and have it checked by a properly trained technician. 2 Before starting your journey, make sure that the tow ball arm is properly locked. Check that: E71330 WARNING • • The tow ball arm may only be inserted when completely unlocked. • • 1. Pull out the plug. 2. Insert the tow ball arm vertically and press it upwards until it engages (1).
Towing Removing the tow ball arm Driving without a trailer 1 3 2 E94771 1. Remove the tow ball arm. 2. Insert the plug into its seat (1). 1 E71332 WARNING 1. Unhitch the trailer. 2. Remove the protecting cap. Press the cap into the key bow. Insert the key and unlock (1). 3. Hold the tow ball arm. Pull the handwheel out, turn it clockwise against the stop (2) and remove the tow ball arm (3). 4. Release the handwheel. Never unlock the tow ball arm with the trailer attached.
Driving Hints In an emergency, the vehicle can be driven through water to a maximum depth of 200 millimetres (8 inches) and at a maximum speed of 10 km/h (6 mph). Extra caution should be exercised when driving through flowing water. RUNNING-IN Tyres WARNING New tyres need to be run-in for approximately 500 kilometres (300 miles). During this time, you may experience different driving characteristics. When driving in water, maintain a low speed and do not stop the vehicle.
Roadside Emergencies FIRST AID KIT Space is provided in the luggage compartment. WARNING TRIANGLE Space is provided in the luggage compartment.
Fuses Load compartment fuse box FUSE BOX LOCATIONS 4-door Engine compartment fuse box This fuse box is located in the engine compartment See Maintenance (page 196). Passenger compartment fuse box E135336 5-door E130170 E135337 E130171 1. Pinch the retaining clips to release the cover. 2. Lower the fuse box cover and pull it towards you. Install in the reverse order.
Fuses Estate CHANGING A FUSE WARNINGS Do not modify the electrical system of your vehicle in any way. Have repairs to the electrical system and the replacement of relays and high current fuses carried out by a properly trained technician. Switch the ignition and all electrical equipment off before touching or attempting to change a fuse. CAUTION E135338 Fit a replacement fuse with the same rating as the one you have removed. Note: You can identify a blown fuse by a break in the filament.
Fuses FUSE SPECIFICATION CHART Engine compartment fuse box E129925 Fuse Ampere rating 7 40 Anti-lock Braking System pump, electronic stability program pump 8 30 Electronic stability program valve Circuits protected 9 30 Heated rear window 10 40 Heater blower 11 30 Start-stop module 12 30 Engine management systems, exhaust gas recirculation relay 13 30 Starter relay 14 40 Heated windscreen (right-hand side) 186
Fuses Fuse Ampere rating 15 25 Transmission control module, intercooler fan - 1.
Fuses Fuse Ampere rating 36 10 37 - Not used 38 15 Powertrain control module, transmission control module Circuits protected Powertrain control module 39 5 Headlamp control module (halogen levelling) 40 5 Electric power assisted steering 41 20 Body control module 42 15 Rear window wiper 43 15 Headlamp control module (high intensity discharge levelling), adaptive front lighting unit 44 5 Adaptive cruise control 45 10 Heated washer jets 46 25 Electric windows (front) 47 7
Fuses Passenger compartment fuse box E129926 189
Fuses Fuse Ampere rating 56 20 57 - Not used 58 - Not used 59 5 Passive anti-theft system supply 60 10 Interior lamps, driver's door switch pack, glove box, ambient lighting, electric sunroof 61 20 Cigar lighter, rear power outlet 62 5 Rain sensor module, humidity sensor, auto-dimming mirror 63 10 Adaptive cruise control 64 - Circuits protected Fuel pump supply Not used 65 10 Luggage compartment lid release 66 20 Driver's door lock, double locking 67 7.
Fuses Fuse Ampere rating 80 20 81 5 82 20 Washer pump ground Circuits protected Electric sunroof Interior motion sensor, radio frequency receiver 83 20 Central locking ground 84 20 Driver's door unlock and double locking ground 85 7.
Fuses Fuse Ampere rating Circuits protected 4 25 Door module (left-hand front) (electric windows, central locking, electric folding mirrors, heated exterior mirrors) 5 25 Door module (right-hand front) (electric windows, central locking, electric folding mirrors, heated exterior mirrors) 6 25 Door module (left-hand rear) (electric windows) 7 25 Door module (right-hand rear) (electric windows) 8 10 Alarm system Power driver's seat 9 25 10 - 11 25 Power front passenger's seat - 2.
Fuses Fuse Ampere rating 28 - Not used 29 5 Blind spot monitor, lane keeping aid, active city stop, rear view camera (without start-stop module) 30 5 Parking aid module 31 - Not used Circuits protected 32 - Not used 33 - Not used 34 15 Heated driver's seat 35 15 Heated front passenger's seat 36 - Not used 37 5 Electric sunroof 38 - Not used 39 - Not used 40 - Not used 41 5 Retractable tow ball 42 - Not used 43 - Not used 44 - Not used 45 - Not used 4
Vehicle recovery Rear towing eye TOWING POINTS Towing eye location The screw-in towing eye is located in the spare wheel well. The towing eye must always be carried in the vehicle. Installing the towing eye CAUTION The screw-in towing eye has a left-hand thread. Turn it anti-clockwise to install it. Make sure that the towing eye is fully tightened. Note: On vehicles with a tow bar, the towing eye cannot be installed at the rear of the vehicle. Use the tow bar to tow a vehicle.
Vehicle recovery CAUTIONS Too much tension in the tow rope could cause damage to your vehicle or the vehicle that is towing. Select neutral when your vehicle is being towed. In the event of a breakdown or mechanical failure do not use individual axle carriers. Your vehicle must be recovered with either ALL wheels on the ground or transported with ALL wheels lifted clear of the ground on a level platform. Drive off slowly and smoothly without jerking the vehicle that is towing.
Maintenance Check when refuelling GENERAL INFORMATION • Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford Authorised Repairers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialised tools developed specifically for servicing your vehicle.
Maintenance E133239 E87786 Move the yellow catch to the right. Open the bonnet and support it with the strut. Closing the bonnet WARNING Make sure that the bonnet is closed properly. Lower the bonnet and allow it to drop from under its own weight for the last 20 – 30 centimetres (8 - 11 inches).
Maintenance UNDER BONNET OVERVIEW - 1.0L ECOBOOST B A I E141341 1 C G H E D F A Brake and clutch fluid reservoir (right-hand drive). See Brake and Clutch Fluid Check (page 209). B Engine oil filler cap . See Engine Oil Check (page 207). C Brake and clutch fluid reservoir (left-hand drive). See Brake and Clutch Fluid Check (page 209). D Battery. See Vehicle battery (page 215). E Engine compartment fuse box. See Fuses (page 184). 1 F Air cleaner. No maintenance necessary.
Maintenance UNDER BONNET OVERVIEW - 1.6L DURATEC-16V (SIGMA) A I B C D E H F G E130030 * A Engine coolant reservoir : See Engine Coolant Check (page 208). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 209). C Engine oil filler cap : See Engine Oil Check (page 207). D Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid Check (page 209). E Battery: See Vehicle battery (page 215).
Maintenance * * H Engine oil dipstick : See Engine Oil Check (page 207). I Screen washer fluid reservoir : See Washer Fluid Check (page 209). * For easy identification, filler caps and the engine oil dipstick are marked in colour. UNDER BONNET OVERVIEW - 1.6L ECOBOOST SCTI (SIGMA) B A I H C G D E F E132729 A Brake and clutch fluid reservoir (right-hand drive). See Brake and Clutch Fluid Check (page 209). B Engine oil filler cap . See Engine Oil Check (page 207).
Maintenance 1 C Brake and clutch fluid reservoir (left-hand drive). See Brake and Clutch Fluid Check (page 209). D Battery. See Vehicle battery (page 215). E Engine compartment fuse box. See Fuses (page 184). F Air cleaner. No maintenance necessary. G Engine oil dipstick . See Engine Oil Check (page 207). H Screen washer fluid reservoir. See Washer Fluid Check (page 209). I Engine coolant reservoir. See Engine Coolant Check (page 208).
Maintenance 1 D Battery. See Vehicle battery (page 215). E Engine compartment fuse box. See Fuse Specification Chart (page 186). F Air cleaner. No maintenance necessary. G Engine oil dipstick . See Engine Oil Check (page 207). H Screen washer fluid reservoir. See Washer Fluid Check (page 209). I Engine coolant reservoir. See Engine Coolant Check (page 208). 1 The filler caps and the engine oil dipstick are coloured for easy identification. UNDER BONNET OVERVIEW - 2.
Maintenance * * A Engine coolant reservoir : See Engine Coolant Check (page 208). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 209). C Engine oil filler cap : See Engine Oil Check (page 207). D Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid Check (page 209). E Battery: See Vehicle battery (page 215). F Engine compartment fuse box: See Fuses (page 184). G Air cleaner: No maintenance necessary.
Maintenance UNDER BONNET OVERVIEW - 1.6L DURATORQ-TDCI (DV) DIESEL A I B C D E F H G E130031 * A Engine coolant reservoir : See Engine Coolant Check (page 208). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 209). C Engine oil filler cap : See Engine Oil Check (page 207). D Brake and clutch fluid reservoir (left-hand drive) : See Brake and Clutch Fluid Check (page 209). E Battery: See Vehicle battery (page 215).
Maintenance * * H Engine oil dipstick : See Engine Oil Check (page 207). I Screen washer fluid reservoir : See Washer Fluid Check (page 209). * For easy identification, filler caps and the engine oil dipstick are marked in colour. UNDER BONNET OVERVIEW - 2.0L DURATORQ-TDCI (DW) DIESEL A I B C D E F H G E130032 * A Engine coolant reservoir : See Engine Coolant Check (page 208). B Brake and clutch fluid reservoir (right-hand drive) : See Brake and Clutch Fluid Check (page 209).
Maintenance * E Battery: See Vehicle battery (page 215). F Engine compartment fuse box: See Fuses (page 184). G Air cleaner: No maintenance necessary. H Engine oil filler cap : See Engine Oil Check (page 207). I Screen washer fluid reservoir : See Washer Fluid Check (page 209). * * For easy identification, filler caps and the engine oil dipstick are marked in colour. ENGINE OIL DIPSTICK - 1.0L ECOBOOST A ENGINE OIL DIPSTICK - 1.
Maintenance A ENGINE OIL DIPSTICK - 1.6L DURATORQ-TDCI (DV) DIESEL/2.0L DURATORQ-TDCI (DW) DIESEL B A E134040 A MIN B MAX ENGINE OIL DIPSTICK - 2.0L DURATEC-HE (MI4) A B E95543 B A MIN B MAX ENGINE OIL CHECK CAUTION Do not use oil additives or other engine treatments. Under certain conditions, they could damage the engine. E134040 A MIN B MAX Note: The oil consumption of new engines reaches its normal level after approximately 5000 kilometres (3000 miles).
Maintenance Remove the dipstick and wipe it with a clean, lint free cloth. Replace the dipstick and remove it again to check the oil level. Note: Coolant expands when it is hot. The level may therefore extend beyond the MAX mark. If the level is at the MIN mark, top up immediately. If the level is at the MIN mark, top up immediately. Topping up Topping up WARNINGS Only top up when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down.
Maintenance Note: The brake and the clutch systems are supplied from the same reservoir. BRAKE AND CLUTCH FLUID CHECK Top up with fluid that meets the Ford specification. See Technical Specifications (page 209). WARNINGS Use of any fluid other than the recommended brake fluid may reduce brake efficiency and not meet Ford's performance standards. WASHER FLUID CHECK Note: The front and rear washer systems are supplied from the same reservoir. Do not allow the fluid to touch your skin or eyes.
Maintenance Specification Viscosity Grade Recommended fluid Antifreeze WSS-M97B44-D - Motorcraft SuperPlus Antifreeze Brake fluid WSS-M6C65-A2 or ISO 4925 Class 6 - Motorcraft or Ford DOT 4 LV High Performance Brake Fluid Item Your engine has been designed to be used with Castrol and Ford Engine Oil, which gives a fuel economy benefit whilst maintaining the durability of your engine.
Maintenance Variant Item 1.0L EcoBoost Cooling system 1.6L Duratec-16V Ti-VCT Engine oil - with filter 1.6L Duratec-16V Ti-VCT Engine oil - without filter 1.6L Duratec-16V Ti-VCT Cooling system 1.6L EcoBoost Engine oil - with filter 1.6L EcoBoost Engine oil - without filter 1.6L EcoBoost Cooling system 2.0L Duratec-HE - MI4 Engine oil - with filter 2.0L Duratec-HE - MI4 Engine oil - without filter 2.0L Duratec-HE - MI4 Cooling system Capacity in Litres (gallons) approx. 6.3 (1.4) 4.
Maintenance Engine Capacity in litres (gallons) 2.0L Duratec-HE - MI4 and 2.0L EcoBoost - MI4 0.9 (0.2) 1.6L Duratorq-TDCi 1.6 (0.4) 2.0L Duratorq-TDCi - DW 1.8 (0.
Vehicle Care Cleaning the chrome trim CLEANING THE EXTERIOR CAUTION WARNING Do not use abrasives or chemical solvents. Use soapy water. If you use a car wash with a waxing cycle, make sure that you remove the wax from the windscreen. Cleaning the alloy wheels CAUTIONS Prior to using a car wash facility check the suitability of it for your vehicle. Note: Do not apply a cleaning chemical to warm or hot wheel rims and covers.
Vehicle Care Rear windows Using other non-recommended cleaning products can result in severe and permanent cosmetic damage. CAUTIONS Do not use any abrasive materials to clean the interior of the rear windows. Body paintwork preservation Do not install stickers or labels to the interior of the rear windows. CAUTIONS Do not polish your vehicle in strong sunshine. REPAIRING MINOR PAINT DAMAGE Do not allow polish to touch plastic surfaces. It could be difficult to remove.
Vehicle battery To connect the booster cables JUMP-STARTING THE VEHICLE WARNING Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. A CAUTIONS Connect batteries with only the same nominal voltage. Always use booster cables with insulated clamps and adequate size cable. C D Do not disconnect the battery from the vehicle’s electrical system. B E102925 1.
Vehicle battery BATTERY CONNECTION POINTS CAUTIONS Do not connect to the negative (–) terminal of the flat battery. CAUTION Make sure that the cables are clear of any moving parts and fuel delivery system parts. Do not connect to the negative (–) terminal of the flat battery. To start the engine 1. Run the engine of vehicle B at moderately high speed. 2. Start the engine of vehicle A. 3. Run both vehicles for a minimum of three minutes before disconnecting the cables.
Wheels and Tyres Refer to the following information before changing the road wheel. GENERAL INFORMATION CAUTIONS Use only approved wheel and tyre sizes. Using other sizes could damage the vehicle and will make the National Type Approval invalid. WARNINGS Drive the shortest possible distances. Do not fit more than one spare wheel on your vehicle at any one time. If you change the diameter of the tyres from that fitted at the factory, the speedometer may not display the correct speed.
Wheels and Tyres Vehicles without tyre repair kit WARNINGS Never place anything between the jack and the ground, or the jack and the vehicle. Your vehicle jack, wheel brace, screw-in towing eye and wheel trim remover are located in the spare wheel well. Note: Vehicles with a tyre repair kit are not equipped with a vehicle jack or a wheel brace. Jacking and lifting points It is recommended to use a workshop type hydraulic jack for changing between summer and winter tyres.
Wheels and Tyres Assembling the wheel brace A WARNING The screw-in towing eye has a left-hand thread. Turn it anti-clockwise to install it. Make sure that the towing eye is fully tightened. E93302 Small arrow-shaped marks on the sills A show the location of the jacking points. E122502 Insert the screw-in towing eye into the wheel brace. Removing the wheel trim 1 E92932 2 E122314 1. Insert the wheel trim remover. 2. Remove the wheel trim.
Wheels and Tyres Note: Make sure that you pull the wheel trim remover at right angles to the trim. Note: The spare wheel is located under the floor cover in the luggage compartment. Removing a road wheel 1. Install the locking wheel nut key. WARNINGS Park your vehicle in such a position that neither the traffic nor you are hindered or endangered. Set up a warning triangle. Make sure that the vehicle is on firm, level ground with the wheels pointing straight ahead.
Wheels and Tyres WARNING WARNING Do not install alloy wheels using wheel nuts designed for use with steel wheels. Have the wheel nuts checked for tightness and the tyre pressure checked as soon as possible. Note: The wheel nuts of alloy wheels and spoked steel wheels can also be used for the steel spare wheel for a short time (maximum two weeks). TEMPORARY MOBILITY KIT Note: Make sure the wheel and hub contact surfaces are free from foreign matter. Your vehicle may not have a spare tyre.
Wheels and Tyres • • • • • • Drive with caution and avoid making sudden steering or driving manoeuvres, especially if the vehicle is heavily loaded or you are towing a trailer. The kit will provide you with an emergency temporary repair, enabling you to continue your journey to the next vehicle or tyre dealer, or to drive a maximum distance of 200 kilometres (125 miles). Do not exceed a maximum speed of 80 km/h (50 mph). Keep the kit out of the reach of children.
Wheels and Tyres CAUTION G Power plug with cable Screwing the bottle onto the bottle holder will pierce the seal of the bottle. Do not unscrew the bottle from the holder as the sealant will escape. H Compressor switch I Label J Bottle lid K Sealant bottle A 1. Open the lid of the tyre repair kit. 2. Peel off the label I showing the maximum permissible speed of 80 km/h (50 mph) from the casing and attach it to the instrument panel in the driver’s field of view.
Wheels and Tyres 3. If the pressure of the sealant-filled tyre is 1.3 bar (19 psi) or more, adjust it to the specified pressure. See Technical Specifications (page 227). 4. Follow the inflation procedure once again to top up the tyre. 5. Check the tyre pressure again from the pressure gauge F. If the tyre pressure is too high, deflate the tyre to the specified pressure using the pressure relief valve B. 6.
Wheels and Tyres Empty sealant bottles can be disposed of together with normal household waste. Return remains of sealant to your dealer or dispose of it in compliance with local waste disposal regulations. USING WINTER TYRES CAUTION Make sure that you use the correct wheel nuts for the type of wheel the winter tyres are fitted to. TYRE CARE If winter tyres are used, make sure that the tyre pressures are correct. See Technical Specifications (page 227).
Wheels and Tyres USING SNOW CHAINS - 2.0L ECOBOOST SCTI (MI4) WARNINGS Do not drive on significantly under-inflated tyres. This may cause the tyres to overheat and fail. Under-inflation reduces fuel efficiency, tyre tread life and may also affect your ability to drive the vehicle safely. WARNINGS Do not exceed 50 km/h (30 mph). Do not use snow chains on snow-free roads. CAUTIONS Do not bend or damage the valves when you are inflating the tyres. Only fit snow chains to specified tyres.
Wheels and Tyres Note: The system will still function correctly, but there may be an increased detection time. Note: You should reset the system following any adjustment to the tyre pressures or any changing of tyres. System reset Note: Turn the ignition on. Note: Do not reset the system when the vehicle is moving. 1. Using the information display control, navigate to Settings > Driver assist > Deflation detection 2. Press and hold the OK button until confirmation appears.
Wheels and Tyres Up to 160 km/h (100 mph) Normal load Variant * Tyre size Full load Front Rear Front Rear bar (psi) bar (psi) bar (psi) bar (psi) All 205/55 R 16 2.1 (31) 2.1 (31) 2.4 (35) 2.8 (41) 1.0L EcoBoost, 1.6L Duratec-16V TiVCT, 1.6L EcoBoost, 2.0L Duratec-HE MI4, 1.6L DuratorqTDCi 215/55 R 16 * 2.1 (31) 2.1 (31) 2.4 (35) 2.8 (41) 2.0L Duratorq-TDCi - DW 215/55 R 16 * 2.3 (33) 2.1 (31) 2.4 (35) 2.8 (41) 1.0L EcoBoost, 1.6L Duratec-16V TiVCT, 1.6L EcoBoost, 2.
Wheels and Tyres Continuous speed in excess of 160 km/h (100 mph) Normal load Variant Tyre size Full load Front Rear Front Rear bar (psi) bar (psi) bar (psi) bar (psi) 1.0L EcoBoost, 1.6L Duratec-16V TiVCT, 1.6L DuratorqTDCi 205/55 R 16 2.1 (31) 2.1 (31) 2.4 (35) 2.8 (41) 1.6L EcoBoost 205/55 R 16 2.2 (32) 2.1 (31) 2.4 (35) 2.8 (41) 1.0L EcoBoost, 1.6L Duratec-16V TiVCT, 1.6L EcoBoost, 2.0L Duratec-HE MI4, 1.6L DuratorqTDCi 215/55 R 16 2.1 (31) 2.1 (31) 2.4 (35) 2.8 (41) 2.
Wheels and Tyres Tyre pressures (cold tyres) - 2.0L EcoBoost - MI4 Wheel nut torque Wheel type Nm (Ib-ft) All 135 (100) Temporary spare wheel - Up to 80 km/h (50 mph) WARNING Do not switch stability control off if you have fitted a temporary spare wheel to your vehicle. Normal load Tyre size Full load Front Rear Front Rear bar (lbf/in²) bar (lbf/in²) bar (lbf/in²) bar (lbf/in²) T125/80 R 16 4.2 (61) 4.2 (61) 4.2 (61) 4.2 (61) T125/90 R 16 4.2 (61) 4.2 (61) 4.2 (61) 4.
Wheels and Tyres Up to 220 km/h (137 mph) Normal load Tyre size Front Rear Front Rear bar (psi) bar (psi) bar (psi) bar (psi) * 2.4 (35) 2.4 (35) 2.4 (35) 2.8 (41) * 2.4 (35) 2.4 (35) 2.4 (35) 2.8 (41) 235/40 R 18 2.4 (35) 2.4 (35) 2.4 (35) 2.4 (35) 215/55 R 16 215/50 R 17 * Full load Only fit snow chains to specified tyres.
Vehicle identification Note: The vehicle identification plate design may vary to that shown. VEHICLE IDENTIFICATION PLATE B C Note: The information shown on the vehicle identification plate is dependant upon market requirements.
Vehicle identification VEHICLE IDENTIFICATION NUMBER E87496 The vehicle identification number is stamped into the floor panel on the right-hand side, beside the front seat. It is also shown on the left-hand side of the instrument panel.
Capacities and Specifications TECHNICAL SPECIFICATIONS Vehicle dimensions 4-door Dimension description Dimension in mm (inches) Maximum length 4534 (178.5) Overall width including exterior mirrors 2010 (79.1) Overall height - EC kerb weight 1451 - 1484 (57.1 - 58.4) Wheelbase 2648 (104.3) Front track 1544 - 1559 (60.8 - 61.4) Rear track 1534 - 1549 (60.4 - 61) 5-door Dimension description Dimension in mm (inches) Maximum length 4358 - 4412 (171.6 - 173.
Capacities and Specifications Dimension description Dimension in mm (inches) Wheelbase 2648 (104.3) Front track 1544 - 1559 (60.8 - 61.4) Rear track 1534 - 1549 (60.
Capacities and Specifications Towing equipment dimensions A B C E D F G E132737 236
Capacities and Specifications 4-door Item Dimension description A Bumper – centre of tow ball B Attachment point – centre of tow ball C Wheel centre – centre of tow ball Dimension in mm (inches) 77 - 80 (3 - 3.1) 3 (0.1) 1068 - 1071 (42 - 42.2) D Centre of tow ball – side member 515 (20.3) E Distance between side members 1030 (40.6) F Centre of tow ball – centre 1. attachment point 447 - 450 (17.6 -17.7) G Centre of tow ball – centre 2. attachment point 747 - 750 (29.4 - 29.
Capacities and Specifications Estate Item Dimension description Dimension in mm (inches) A Bumper – centre of tow ball 81 (3.2) B Attachment point – centre of tow ball C Wheel centre – centre of tow ball 1094 (43.1) D Centre of tow ball – side member 586 (23.1) E Distance between side members 1172 (46.1) F Centre of tow ball – centre 1. attachment point 474 (18.7) G Centre of tow ball – centre 2. attachment point 719 (28.3) 238 72 - 77 (2.
Audio introduction IMPORTANT AUDIO INFORMATION WARNINGS Due to technical incompatibility, recordable (CD-R) and rewritable (CD-RW) discs may not function correctly. E66257 Disc labels Audio CD These CD radio units will play compact discs that conform to the International Red Book standard audio specification. Copy protected CDs from some manufacturers do not conform to this standard and playback cannot be guaranteed.
Audio unit overview Note: Units have an integrated multi function display situated above the CD aperture. This shows important information regarding control of your audio unit. Additionally, there are various icons placed around the display screen which light up when a function is active (for example CD, Radio or Aux.) Type 1 A B C D E O F N M L G K J I H E130324 A CD eject. See Compact Disc Player (page 252). B Navigation arrows. C CD aperture. See Compact Disc Player (page 252). D OK.
Audio unit overview H Seek up. CD track selection. See Station tuning control (page 247). See Track selection (page 252). I On/off and volume control. J Seek down. CD track selection. See Station tuning control (page 247). See Track selection (page 252). K Menu select. L Sound button. See Sound button (page 247). M Auxiliary select. See Auxiliary input (AUX IN) socket (page 255). See Auxiliary input (AUX IN) socket (page 255). N Radio and waveband select. See Audio unit operation (page 247).
Audio unit overview A B C D E F T S G R Q H P O N M L K J I E130142 A CD eject. See Compact Disc Player (page 252). B Navigation arrows. C CD aperture. See Compact Disc Player (page 252). D OK. E Information. F Traffic announcement. See Traffic information control (page 248). G Sound button. See Sound button (page 247). H Telephone keypad and station presets. See Using the telephone (page 258). See Station preset buttons (page 248). I Function 4. J Function 3.
Audio unit overview L On/off and volume control. M Seek down. CD track selection. See Station tuning control (page 247). See Track selection (page 252). N Function 2. O Function 1. P Menu select. Q Phone menu. See Telephone (page 257). R Auxiliary, USB and iPod select. See Auxiliary input (AUX IN) socket (page 255). See Auxiliary input (AUX IN) socket (page 255). See Connectivity (page 277). S Radio and waveband select. See Audio unit operation (page 247). T CD select.
Audio unit overview A B C D E F G Y X H W I V J U K T L S R Q P O N M E129074 A On/off control. B Display select. C Telephone keypad and station presets. See Using the telephone (page 258). See Station preset buttons (page 248). D CD aperture. See Compact Disc Player (page 252). E Navigation arrows. F DSP select. See Digital signal processing (DSP) (page 250). G CD eject. See Compact Disc Player (page 252). H Information. I Clock. J Seek up. CD track selection.
Audio unit overview L Traffic announcement. See Traffic information control (page 248). M Function 4. N Sound button. See Sound button (page 247). O Function 3. P OK. Q Function 2. R Menu select. S Function 1. T Phone menu. See Telephone (page 257). U Auxiliary select. See Auxiliary input (AUX IN) socket (page 255). See Auxiliary input (AUX IN) socket (page 255). V Seek down. CD track selection. Accept call. See Station tuning control (page 247). See Track selection (page 252).
Audio System Security SECURITY CODE Each unit incorporates a unique code that is linked to the vehicle identification number (VIN). The system will automatically check that the audio unit and vehicle match before allowing operation. If a security code message appears, please see your dealer.
Audio unit operation Note: Service linking allows cross-referencing to other corresponding frequencies of the same station, for example FM and other DAB ensembles. ON/OFF CONTROL Press the button with the ignition switched off. This will operate the audio unit for up to one hour. Note: The system will automatically change to another corresponding station if the current one becomes unavailable, for example when leaving the coverage area.
Audio unit operation Scan tuning AUTOSTORE CONTROL Scan allows you to listen to a few seconds of each station detected. Note: This will store up to a maximum of the 10 strongest signals available, either from the AM or the FM waveband, and overwrite the previously stored stations. It can also be used to store stations manually in the same way as other wavebands. Type 1 1. Press the MENU button. 2. Select RADIO mode and then SCAN. 3. Use the seek buttons to scan up or down the selected waveband. 4.
Audio unit operation Note: When you are listening to a non TA station and turn TA off and on again a TP seek will occur. Traffic announcement volume Traffic announcements interrupt normal broadcasts at a preset minimum level that is usually louder than normal listening volumes. To adjust the preset volume: • Use the volume control to make the necessary adjustment during an incoming TA broadcast. The display will show the level selected.
Audio unit menus AUTOMATIC VOLUME CONTROL NEWS BROADCASTS Some audio units interrupt normal reception to broadcast news bulletins from stations on the FM waveband or radio data system (RDS) and enhanced other network (EON) linked stations, in the same way as traffic information is provided. When available, automatic volume control (AVC) adjusts the volume level to compensate for engine noise and road speed noise. 1. 2. 3. 4. 5. Press the MENU button and select AUDIO. Select AVC LEVEL or ADAPTIVE VOL.
Audio unit menus It will restore radio reception when it finds one or, if one is not found, the unit will return to the original stored frequency. When selected, ‘AF’ will be shown in the display. 1. Press the MENU button. 2. Select AUDIO or AUDIO MENU. 3. Scroll to ALTERNAT FREQ. or ALTERNATIVE FREQ. and turn on or off with the OK button. 4. Press the MENU button to return.
Compact Disc Player COMPACT DISC PLAYBACK SHUFFLE/RANDOM Note: During playback, the display indicates the disc, track and time that has elapsed since the start of the track. Random track playback, also known as shuffle, plays all tracks on the CD in random order. During radio reception, press the CD button once to start CD playback. Type 1 Playback will start immediately after a disc is loaded. 1. Press the MENU button and select CD MODE. 2.
Compact Disc Player When an MP3 CD is playing, options include REPEAT for the track, or to repeat all the tracks in the folder. Repeat presses of function button 1 will toggle these options. When a CD containing audio is inserted into the CD player the disc's directory structure is read in. It may take a while before playback starts and is dependant on the quality of the disc. MP3 tracks may be recorded on the CD in several ways.
Compact Disc Player Note: If the ID3 information selected is unavailable, NO MP3 TAG will be shown in the display. CD text display options When an audio disc with CD text is playing, limited information encoded in each track can be displayed. Such information will normally include: • • • The disc name The artist name The track name. Note: These display options are selected in the same way as MP3 displays. NO DISC NAME or NO TRACK NAME will be shown in the display if no information has been encoded.
Auxiliary input (AUX IN) socket Note: For optimum performance when using any auxiliary device set the volume on the device high. This will reduce audio interference when charging the device via the vehicle power supply socket. When fitted the Auxiliary input (AUX IN) socket permits an auxiliary device, such as an MP3 player, to be linked into the vehicle audio system. Output can be played through the vehicle speakers. To connect an auxiliary device, plug it into the AUX IN socket using a 3.
Audio Troubleshooting AUDIO TROUBLESHOOTING Audio unit display Rectification PLEASE CHECK CD General error message for CD fault conditions, such as cannot read the CD, data-CD inserted, etc. Ensure disc is loaded correct way up. Clean and re-try, or replace disc with known music disc. If error persists contact your dealer. CD DRIVE MALFUNCTION General error message for CD fault conditions such as possible mechanism fault.
Telephone Note: If there is an ongoing call when the phone in use is selected as the new active phone, the call is transferred to the vehicle audio system. GENERAL INFORMATION CAUTION Using the system with the engine off will drain the battery. Note: Even if connected to the car system, your phone can still be used in the usual way. This section describes the functions and features of the Bluetooth mobile phone hands free system.
Telephone Bond another Bluetooth phone After start up access to the phonebook list can be delayed for several minutes, depending upon the size. Bond a new Bluetooth phone as described in the requirements for a Bluetooth connection. Phonebook categories Phones stored in the system are accessible by using the phone list on the audio unit. The category is indicated as an icon: Phone Mobile Note: A maximum of six devices may be bonded.
Telephone Note: You can exit the phone menu by pressing any source button CD, RADIO or AUX. Dialling a number using the telephone keypad 1. Press the PHONE button. 2. Dial the number using the telephone keypad on the audio unit. 3. Press the OK button. Note: If you enter an incorrect digit whilst entering a phone number, press function button 3 to erase the last digit. A long press will erase the complete string of digits.
Telephone Receiving an incoming call Muting the microphone Accepting an incoming call Note: During a call, it is possible to mute the microphone. Whilst muted, confirmation will appear in the display. Incoming calls can be accepted by pressing the seek down button, or by pressing the OK button. Press function button 1. Press the button once again to turn this function off.
Voice control If you are not sure how to continue say "HELP" for assistance or "CANCEL" if you do not wish to continue. PRINCIPLE OF OPERATION CAUTION The "HELP" function provides only a subset of the available voice commands. Detailed explanations of all possible voice commands can be found on the following pages. Using the system with the engine off will drain the battery.
Voice control • • Radio: TUNE NAME. External device (USB and iPod): TRACK. • Store up to 20 name tags per function. • The average recording time for each name tag is approximately 2-3 seconds. Start communicating with the system Before you can start talking to the system you first have to press the VOICE button for each operation and wait until the system answers with a beep. See Voice Control (page 44). AUDIO UNIT COMMANDS CD Player You can control playback directly by voice control.
Voice control Track You can choose a track on your CD directly. Steps User says System answer 1 "CD PLAYER" "CD PLAYER" 2 "TRACK NUMBER PLEASE" "TRACK" 3 "" * "TRACK " ** * Can be used as a shortcut. ** Additionally, numbers can be spoken as up to four single digits (for example "2", "4", "5" for track 245) Shuffle all To set random playback.
Voice control "RADIO" "STORE NAME" "PLAY" * Can be used as a shortcut. Tune frequency This function allows you to tune your radio by voice commands. Steps User says 1 "RADIO" "RADIO" 2 "AM" "AM FREQUENCY PLEASE" "FM" "FM FREQUENCY PLEASE" 3 "" System answer "TUNE " * * The frequency may be entered in a variety of ways. Refer below for representative examples. • • • • • FM band: 87.5 - 108.0 in increments of 0.1 • • • • • "Eighty nine point nine" (89.9) "Ninety" (90.
Voice control Steps User says System answer " STORED" Tune name This function allows you to call up a stored radio station. Steps User says 1 "RADIO" 2 "TUNE NAME" 3 "" System answer "RADIO" "NAME PLEASE" * "TUNE " * Can be used as a shortcut. Delete name This function allows you to delete a stored radio station.
Voice control Delete directory This function allows you to delete all stored radio stations at once. Steps User says System answer 1 "RADIO" "RADIO" 2 "DELETE DIRECTORY" "DELETE DIRECTORY" "CONFIRM YES OR NO" 3 "YES" "RADIO DIRECTORY DELETED" "NO" "COMMAND CANCELLED" Play This function switches the audio source to the radio mode.
Voice control "EXTERNAL DEVICE", "USB" "HELP" "PLAY" "TRACK" * "PLAYLIST" "FOLDER" ** ** "SHUFFLE ALL" "SHUFFLE FOLDER" "SHUFFLE PLAYLIST" "SHUFFLE OFF" "REPEAT TRACK" "REPEAT FOLDER" "REPEAT OFF" * Can be used as a shortcut. ** Playlists and folders activated by voice control must be assigned special filenames. See General Information (page 277). USB play This function allows you to switch the audio source to the attached USB device.
Voice control Steps User says System answer 1 "EXTERNAL DEVICE" "EXTERNAL DEVICE" 2 "USB" "USB" 3 "TRACK" 4 "TRACK NUMBER PLEASE" "" * "TRACK " * Additionally, numbers can be spoken as up to four single digits (for example "2", "4", "5" for track 245) Overview External devices - iPod The overview below shows the available voice commands. The following lists will give further information about the complete command menu in selected examples.
Voice control Steps User says System answer 1 "EXTERNAL DEVICE" "EXTERNAL DEVICE" 2 "IPOD" "IPOD" 3 "TRACK" "TRACK NUMBER PLEASE" 4 "" * "TRACK " ** * Can be used as a shortcut. ** Additionally, numbers can be spoken as up to five single digits (for example "5", "2", "4", "5", "3" for track 52453), to a limit of 65535. iPod playlist You can choose a playlist from your iPod directly.
Voice control "PHONE" "HELP" "MOBILE NAME" "DIAL NUMBER" "DIAL NAME" * * * "DELETE NAME" "DELETE DIRECTORY" "PLAY DIRECTORY" "STORE NAME" "REDIAL" * "ACCEPT CALLS" "REJECT CALLS" * Can be used as a shortcut. Phone functions Dial number Phone numbers can be dialled after giving the name tag voice command.
Voice control Dial name Phone numbers can be dialled after giving the name tag voice command. Steps User says 1 "PHONE" System answer "PHONE" 2 "DIAL NAME" "NAME PLEASE" 3 "" "DIAL " "CONFIRM YES OR NO" 4 "YES" "DIALLING" "NO" "COMMAND CANCELLED" * * Can be used as a shortcut. Redial This function allows you to redial the last dialled phone number.
Voice control DTMF (Tone dialling) Note: DTMF can only be used during an ongoing call. Operate the VOICE button and wait for the system prompt. This function transfers spoken numbers into DTMF tones. For example, to make a remote enquiry to your home answering machine or to enter a PIN number etc. Steps Can only be used with vehicles installed with a dedicated VOICE button.
Voice control Steps User says System answer 1 "PHONE" "PHONE" 2 "DELETE NAME" "NAME PLEASE" 3 "" "DELETE " "CONFIRM YES OR NO" 4 "YES" " DELETED" "NO" "COMMAND CANCELLED" Play directory Use this function to let the system tell you all stored entries. Steps User says System answer 1 "PHONE" "PHONE" 2 "PLAY DIRECTORY" "PLAY DIRECTORY" Delete directory This function allows you to delete all entries in one go.
Voice control Steps User says System answer 1 "PHONE" "PHONE" 2 "REJECT CALLS" "ACCEPT CALLS" "REJECT CALLS" "ACCEPT CALLS" * * use this command to turn the reject mode off Overview CLIMATE CONTROL COMMANDS The overview below shows the available voice commands. The following lists will give further information about the complete command menu in selected examples. Climate The climate voice commands supports the functionality of the fan speed, temperature and mode settings.
Voice control Steps User says System answer 1 "CLIMATE" "CLIMATE" 2 "‘FAN" "MINIMUM" "FAN MINIMUM" 3 "" "FAN " "MAXIMUM" "FAN MAXIMUM" "FAN SPEED PLEASE" * * Can be used as a shortcut. On vehicles fitted with an English language module the "FAN" shortcut is not available.
Voice control Steps User says System answer "" or "" "TEMPERATURE " "MAXIMUM" "TEMPERATURE MAXIMUM" * Can be used as a shortcut. Auto mode Steps User says System answer 1 "CLIMATE" "CLIMATE" 2 "AUTO MODE" "AUTO MODE" * * Can be used as a shortcut. Can be deactivated by selecting a different temperature or fan speed.
Connectivity The system supports a range of external devices, to fully integrate with your audio unit via the USB and auxiliary input sockets. Once connected, control of the external device is possible via the audio unit. GENERAL INFORMATION CAUTIONS Take care when handling external devices with exposed electrical connectors (such as the USB plug). Always replace the protective cap/shield when possible. There may be a risk of electrostatic discharge causing damage to the device.
Connectivity Connection To enable voice control for custom playlists and folders, follow the procedure below: • Create folders named with the structure "Ford<*>" where <*> is a number 1-10. For example "Ford3" without an extension. • Create playlists named with the structure "Ford<*>.m3u" where <*> is a number 1-10. For example "Ford5.m3u" without any space between "Ford" and the number. Plug in the device, and if necessary secure it to prevent movement within the vehicle.
Connectivity 2. Press the up and down arrow buttons to select the desired function. 3. Press the OK button. Track title E100027 Information not available Tracks can be accessed by skipping forwards and backwards using the steering wheel controls, or directly from the audio unit controls. E100028 Operation Audio control Select the USB device as the audio source by repeatedly pressing the AUX button until the USB screen appears in the display.
Connectivity Note: If you wish to jump to the top level of the USB device contents, press and hold the left arrow key. iPod generic category E100036 iPod generic media file Audio control E100037 Press the seek up and down keys to skip backwards and forwards through tracks. Operation Press and hold the seek keys to enable fast rewind/fast forward through track content. Connect the iPod. See Connecting an external device (page 278).
Connectivity Note: If you wish to jump to the top level of the iPod contents, press and hold the left arrow key. Audio control Press the seek up and down keys to skip backwards and forwards through tracks. Press and hold the seek keys to enable fast rewind/fast forward through track content. Use the function buttons to enable shuffle and repeat with respect to playlists. Press function button 3 to scan the whole device or a playlist if it is in operation.
Navigation introduction GENERAL INFORMATION CAUTIONS Use only 12 cm (4.7 inches) discs or 8 cm (3.1 inches) discs with a suitable adaptor. Press the relevant button on the unit bezel to access the system functions. This will take you into the selected mode. Do not attempt to open the unit. If the unit malfunctions consult your dealer. One hour mode Improper use of settings and connections, other than those explained in this handbook, can damage the unit.
Navigation introduction Safety information Read and follow all stated safety precautions. Failure to do so may increase your risk of collision and personal injury. Ford Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines. If detailed viewing of route instructions is necessary, pull off the road when it is safe to do so and park your vehicle. Do not use the navigation system to locate emergency services.
Navigation unit overview A Descriptions for function buttons 1-4 Function buttons 1 to 4 are context dependent, and change according to the current unit mode. Descriptions for the functions are shown at the bottom of the screen display.
Navigation unit overview Vehicles with CD-SD navigation system A B C E D F G V U H T S I R J Q K P N O M L E129241 A CD eject. B Navigation arrows. C CD aperture. D OK. E Information. F Map select. See Route displays (page 296). G Menu select. See System settings (page 292). H Telephone keypad and station presets. See Audio unit operation (page 247). See Audio unit menus (page 250). See Telephone (page 257). I Clock. See System settings (page 292).
Navigation unit overview L Function 3. M Seek up. CD track selection. See Station tuning control (page 247). See Track selection (page 252). N On/off and volume control. See On/off control (page 247). O Seek down. CD track selection. See Station tuning control (page 247). See Track selection (page 252). P Function 2. Q Function 1. R Phone select. See Telephone (page 257). S Auxiliary select. See Auxiliary input (AUX IN) socket (page 255). T Radio select. See Audio unit operation (page 247).
Navigation unit overview Vehicles with Sony CD-SD navigation system A B C D E F G Y X H W I V J U K T L S R Q P O N M E129242 A On/off control. See On/off control (page 247). B Navigation select. See System settings (page 292). C Telephone keypad and station presets. See Audio unit operation (page 247). See Audio unit menus (page 250). See Telephone (page 257). D CD aperture. E Navigation arrows. F Map select. See Route displays (page 296). G CD eject. H Information.
Navigation unit overview K Home select. See System settings (page 292). L Traffic announcement. See Traffic Message Channel (page 297). M Function 4. N Sound select. See Sound button (page 247). O Function 3. P OK. Q Function 2. R Menu select. See System settings (page 292). S Function 1. T Phone select. See Telephone (page 257). U Auxiliary select. See Auxiliary input (AUX IN) socket (page 255). V Seek down. CD track selection. accept call. See Station tuning control (page 247).
Navigation Quick start Vehicles with mobile navigation system Installing the micro SD card CAUTION Using the system with the engine off will drain the battery. 1 Note: You will be charged when sending and receiving text messages. Note: Refer to your phone handbook for all phone functions and operation. 2 Note: Keep the activation code (printed on the installation guide) in a safe place. Note: Retain the activation text message in your mobile phone inbox. E114212 1.
Navigation Quick start 3. Press the OK button to activate your selection. Selection lists Various screens are presented which offer a selection list of available options. 1. Select the option you require, or if it is not shown on the screen use the up and down arrow buttons to view the remainder of the selection list. 2. Press the OK button to confirm your selection. E114213 2. Switch your mobile phone on and start the "Ford Mobile Navigation". 3. Choose "Select Destination". 4. Choose "Enter Address".
Navigation Quick start • • • Starting from the top, select the country followed by either the postcode if available or city and street name. Use the alphanumeric keypad and selection lists to select your address details. Once sufficient information has been entered, scroll to Start guidance and press the OK button to activate your selection. Note: If you only need to navigate to a city centre for example, full address details are not required.
System settings Most of the important settings for your navigation unit can be accessed via the MENU or NAV button. The following section describes the various options and how to use them. Last destinations This feature allows quick access to a history of previous destinations entered in the system. A detailed display will show the complete stored information including an overview map. Select the required repeat destination from the list. For menu structures: See Information Displays (page 78).
System settings Special functions Nav audio mixing This feature allows you to select GPS and system information or a demonstration of the system functionality. This feature allows you to adjust the volume mix between the navigation voice output and audio source. Map display DSP settings This feature allows you to change the way the map screen is displayed (for example clean 2D and clean 3D view) and to customise display information for your journey (for example time to arrival and lane guidance).
System settings Clock settings Set time This feature allows you to manually adjust the time. Set date This feature allows you to manually adjust the date, month and year. GPS time This feature allows you to, if in a suitable coverage area, automatically adjust the date and time using GPS. Set time zone This feature allows you select a specific time zone. Summertime This feature allows you set the system to adjust for seasonal time differences. Note: GPS time must be selected.
Navigation system ROUTE OPTIONS MENU Eco settings You can set a number of options which alter the way a route is planned. Trailer Use this feature to change the economy settings of your journey relating to whether or not you are towing a trailer and if so the size of trailer being towed. Using the up, down, left and right arrow buttons, you can select from the list which road features are to be avoided or included in the route by turning the feature on or off.
Navigation system Seasonal roads Junction zoom When switched on the system will look for seasonal roads on your route and automatically update your route distance and timings. This feature will automatically increase the zoom on the map display at times when you are required to make a turn, or perform more complex manoeuvres. Shortly after the zoom scale will return to the previous level. Note: This feature can be useful in avoiding delays or hold ups on journeys. Select AUTO to activate junction zoom.
Traffic Message Channel You may either select a view which shows messages only affecting your programmed route, or a view which shows all messages received. Press function button 1 to change the view. PRINCIPLE OF OPERATION Traffic message channel (TMC) stations are broadcast on the FM waveband. TMC is a feature that receives traffic alerts which can be used to plan alternative routes and avoid hold ups.
Map updates The road network is constantly changing due to new roads, changes in road classification, etc. Therefore, it is not always possible to exactly match the map data in the system to the current road network. Map information is regularly updated, but all areas are not necessarily covered to the same level of detail. Some roads, in particular private roads, may not be included on the database. To help with accuracy, always use the latest version navigation disc.
Appendices www.novero.com/declaration_of_conformity TYPE APPROVALS The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Ford Motor Company is under license. Other trademarks and trade names are those of their respective owners. FCC/INDUSTRY CANADA NOTICE This device complies with Part 15 of the FCC Rules.
Appendices E114220 TYPE APPROVALS TYPE APPROVALS Laser sensor E97713 E97714 SD Logo is a trademark.
Appendices WARNINGS Invisible laser radiation. Do not view directly with optical instruments (magnifiers). Class 1M laser product. WARNINGS IEC 60825-1: 1993 + A2:2001. Complies with FDA performance standards for laser products except for deviation pursuant to Laser Notice No. 50, dated July 26th, 2001. Item Specification Max average power 45mW Pulse duration 33ns Wavelength 905nm TYPE APPROVALS TYPE APPROVALS The navigation software is based in part on the work of the independent JPEG Group.
Appendices WARNINGS Do not mount any transceiver, microphones, speakers, or any other item in the deployment path of the airbag system. WARNINGS Do not fasten antenna cables to original vehicle wiring, fuel pipes and brake pipes. Keep antenna and power cables at least 10 centimetres (4 inches) from any electronic modules and airbags. 1 2 3 4 E85998 Frequency Band Maximum output power Watt (Peak MHz RMS) Antenna Positions 1 – 30 50 W 3, 4 30 – 54 50 W 1, 2, 3 68 – 87.
Appendices Note: After the installation of RF transmitters, check for disturbances from and to all electrical equipment in the vehicle, both in the standby and transmit modes. Check all electrical equipment: • with the ignition ON • with the engine running • during a road test at various speeds. Check that electromagnetic fields generated inside the vehicle cabin by the transmitter installed do not exceed applicable human exposure requirements.
304
Index A Audible Warnings and Indicators.............76 Automatic transmission....................................76 Door open................................................................76 Frost...........................................................................76 Key outside car......................................................76 Lights on..................................................................76 Low fuel....................................................................
Index C Automatic Transmission............................134 Emergency park position release lever....................................................................136 Hints on driving with an automatic transmission....................................................135 Selector lever positions....................................134 Sport mode and manual shifting.................135 Capacities and Specifications................234 Technical Specifications.................................
Index D Child Safety Locks..........................................23 Electric child safety locks..................................23 Manual child safety locks..................................23 Diesel Particulate Filter...............................123 Child Seat Positioning...................................18 Child Seats.........................................................17 Regeneration........................................................123 Digital signal processing (DSP).............
Index Engine Block Heater....................................124 Engine Coolant Check...............................208 Fuel Quality - Diesel....................................128 Checking the coolant level............................208 Topping up...........................................................208 Fuel Quality - E85........................................128 Engine immobiliser.......................................40 Fuel Quality - Petrol....................................
Index Heated Seats...................................................114 Heated Windows and Mirrors..................104 Information Messages.................................86 Active City Stop.....................................................87 Airbag........................................................................87 Alarm.........................................................................87 Automatic main beam control........................87 Battery and charging system...................
Index J Loading the navigation data...................288 Jump starting Locking and Unlocking.................................33 Loading the navigation data.........................288 Double locking.......................................................33 Locking.....................................................................33 Locking and unlocking confirmation............34 Locking and unlocking the doors from inside....................................................................
Index MP3 display options...................................253 Personalised Settings..................................85 CD text display options...................................254 Chime deactivation.............................................86 Language setting.................................................85 Measure units........................................................86 Temperature units...............................................86 MP3 file playback..................................
Index S Remote control battery See: Changing the remote control battery.................................................................30 Safety Precautions.......................................128 Satellite Navigation Unit Holder..............118 Remote control programming See: Programming the remote control........30 Adjusting the holder...........................................118 Removing a Headlamp................................56 Repairing Minor Paint Damage................
Index Station tuning control................................247 Temporary Mobility Kit................................221 DAB service linking............................................247 Manual tuning.....................................................247 Scan tuning..........................................................248 Seek tuning...........................................................247 Checking the tyre pressure.............................224 General information.........................
Index Type approvals.............................................299 Using Adaptive Cruise Control................156 Certificate for United Arab Emirates...........301 EU Declaration.....................................................301 FCC/INDUSTRY CANADA NOTICE.............299 Laser sensor........................................................300 RX-42 - declaration of conformity..............299 Tyre Care.........................................................225 Tyre Pressure Monitoring System..
Index Using Stability Control - 2.0L EcoBoost SCTi (MI4)....................................................139 Ventilation See: Climate Control..........................................98 Vents Switching sport mode on................................139 Switching the system off.................................139 See: Air Vents........................................................98 Using Stability Control...............................138 Using start-stop............................................
Index Windscreen Washers...................................46 Windscreen Wipers.......................................45 Automatic wiper system...................................45 Intermittent wipe.................................................45 Winter Tyres See: Using Winter Tyres...................................225 Wipers and Washers.....................................
(CG3568en)
