FordKuga Owner's handbook Feel the difference
The information contained in this publication was correct at the time of going to print. In the interest of development the right is reserved to change specifications, design or equipment at any time without notice and without incurring any obligations. This publication, or part thereof, may not be reproduced nor translated without our approval. Errors and omissions excepted. © Ford Motor Company 2009 All rights reserved.
Table of contents Introduction Alarm About this handbook................................5 Symbols glossary......................................5 Parts and accessories..............................5 Arming the alarm.....................................37 Disarming the alarm................................37 Steering wheel Quick start Adjusting the steering wheel.................39 Audio control...........................................39 Voice control............................................
Table of contents Auto-dimming mirror..............................62 USB port.................................................100 Floor mats...............................................100 Instruments Starting the engine Gauges.....................................................63 Warning lamps and indicators..............64 Audible warnings and indicators..........66 General information...............................101 Keyless starting......................................
Table of contents Using the rear view camera..................117 Maintenance Towing a trailer.......................................127 Detachable tow ball...............................127 General information..............................142 Opening and closing the bonnet........142 Engine compartment overview - 2.5L Duratec (VI5).......................................144 Engine compartment overview - 2.0L Duratorq-TDCi (DW) Diesel..............145 Engine oil dipstick - 2.5L Duratec (VI5)..............
Table of contents Technical specifications Technical specifications.........................171 Telephone General information...............................175 Telephone setup....................................175 Bluetooth setup.....................................176 Telephone controls................................177 Using the telephone - Vehicles Without: Navigation System.............................177 Using the telephone - Vehicles With: Navigation System.............................
Introduction ABOUT THIS HANDBOOK SYMBOLS GLOSSARY Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this handbook. The more that you know about it, the greater the safety and pleasure you will get from driving it. Symbols in this handbook WARNING You risk death or serious injury to yourself and others if you do not follow the instructions highlighted by the warning symbol.
Introduction The use of Ford Original Parts ensures that your vehicle is repaired to its pre-accident condition and maintains its maximum residual value. Ford Original Parts match Ford's stringent safety requirements and high standards of fit, finish and reliability. Quite simply, they represent the best overall repair value, including parts and labour costs. Now it is easier to tell if you have really been given Ford Original Parts.
Introduction E98917 E89939 Exterior mirror Lighting • • • Rear lamps Rear fog lamp Headlamp E98918 Glass • • • Rear window Side glass Windscreen E98920 7
Quick start QUICK START Instrument panel overview Left-hand drive A B T C S D R E Q F G P O E78209 8 H I N J K M L
Quick start Right-hand drive G J O I N H M K C E L S D F Q B R A P T E78210 A Lighting control. See Lighting control (page 46). Front fog lamps. See Front fog lamps (page 47). Rear fog lamp. See Rear fog lamps (page 47). B Headlamp levelling control. See Headlamp levelling (page 47). C Multi-function lever: Information display controls. Direction indicators. See Direction indicators (page 50). Main beam. See Lighting control (page 46). D Instrument cluster. See Gauges (page 63).
Quick start E Horn. F Wiper lever. See Wipers and washers (page 41). G Card holder. H Air vents. See Air vents (page 80). I Hazard warning flasher switch. See Hazard warning flashers (page 48). J Airbag deactivation indicator. See Disabling the passenger airbag (page 25). Parking aid switch. See Using the parking aid (page 115). J Start button. See Keyless starting (page 101). K Heated windscreen switch. See Heated windows and mirrors (page 86). L Heated rear window switch.
Quick start Locking and unlocking Opening the luggage compartment lid Unlocking the vehicle A B C E71963 A Unlock B Lock C Tailgate unlock Press the unlock button once to unlock the vehicle. See Programming the remote control (page 27). A B Press and hold the unlock button for three seconds to unlock the vehicle and open the windows (global opening)*. E99409 Press the lock button once to activate central locking and arm the alarm. To open the main luggage compartment lid, press switch A.
Quick start Keyless entry Locking the vehicle E78276 E87384 Passive locking and unlocking requires a valid passive key to be located within one of the three external detection ranges. Locking buttons are located on each of the front doors. See Keyless entry (page 31). Unlocking the vehicle Keyless starting E85766 Press the start button. See Keyless starting (page 101).
Quick start Manual climate control 2 Defrosting and demisting the windscreen 2 1 E95178 E71382 Rapid heating of vehicle interior E71377 See Manual climate control (page 81). 3 E95179 WARNING Make sure that you fully engage the locking lever when returning it to its original position. See Adjusting the steering wheel (page 39).
Quick start Automatic climate control A E See Lighting control (page 46). B D Direction indicators C E78730 A Windscreen defrosting/demisting E71098 B Toggle mono mode on and off If the lever is tapped up or down, the direction indicators will flash three times. C Air conditioning OFF D Recirculated air E Air conditioning ON See Direction indicators (page 50). Autowipers See Automatic climate control (page 83). B Autolamps E71014 Move the lever up one position.
Quick start Airbag Towing the vehicle on four wheels CAUTION For certain engine and transmission combinations, it is recommended not to tow the vehicle with the drive wheels on the ground. See Towing the vehicle on four wheels (page 140). E69213 WARNING To avoid the risk of death or serious injury, never use a rearward facing child restraint in the front, unless the air bag is off. See Child safety (page 16). See Disabling the passenger airbag (page 25).
Child safety Only child restraints certified to ECE-R44.03 (or later) have been tested and approved for use in your vehicle. A choice of these are available from your Dealer. CHILD SEATS Child restraints for different mass groups Use the correct child restraint as follows: Baby safety seat E68916 WARNINGS Secure children that are less than 150 centimetres tall or less than 12 years of age in a suitable, approved child restraint, in the rear seat. Original text according to ECE R94.
Child safety Child safety seat WARNINGS If the foam spacer is damaged or missing, remove the storage compartment cover and extend the leg to the base of the compartment. All vehicles WARNING When fitting a child seat using the vehicle seat belts make sure the belts are not slack. CAUTION When using a child seat on a rear seat, make sure that the child seat rests tightly against the vehicle seat. It may be necessary to lift or remove the head restraint. See Head restraints (page 90).
Child safety Seating positions Mass group categories 0 0+ I II III Up to 10 kg Up to 13 kg 9 - 18 kg 15 - 25 kg 22 - 36 kg U U U U U Rear seats X Not suitable for children in this mass group. U Suitable for universal category child seats approved for use in this mass group. U¹ Suitable for universal category child seats approved for use in this mass group. However, we recommend that you secure children in a government approved child seat, in the rear seat.
Child safety Booster seat (Group 2) BOOSTER CUSHIONS WARNINGS Do not install a booster seat or a booster cushion with only the lap strap of the seat belt. Do not install a booster seat or a booster cushion with a seat belt that is slack or twisted. Do not put the seat belt under your child’s arm or behind its back. Do not use pillows, books or towels to boost your child’s height. Make sure that your children sit in an upright position.
Child safety ISOFIX ANCHOR POINTS WARNING Use an anti-rotation device when using the ISOFIX system. We recommend that you use a top tether or a support leg. Attaching a child restraint with a top tether E68945 You can fit ISOFIX child restraints using the ISOFIX anchor points. Your vehicle is fitted with ISOFIX anchor points that accommodate universally approved ISOFIX child restraints.
Child safety CHILD SAFETY LOCKS WARNING You cannot open the doors from inside if you have put the child safety locks on. E112197 Left-hand side Turn anti-clockwise to lock and clockwise to unlock. Right-hand side Turn clockwise to lock and anti-clockwise to unlock.
Occupant protection Driver and front passenger airbags PRINCIPLE OF OPERATION Airbags WARNINGS Do not modify the front of your vehicle in any way. This could adversely affect deployment of the airbags. Original text according to ECE R94.01: Extreme Hazard! Do not use a rearward facing child restraint on a seat protected by an airbag in front of it! E74302 Wear a seat belt and keep sufficient distance between yourself and the steering wheel.
Occupant protection Seat belts The side airbags will deploy during significant lateral collisions. Only the airbag on the side affected by the collision will deploy. The airbags will inflate within a few thousandths of a second and deflate on contact with the occupants, thus providing protection for the chest and shoulder areas. During minor lateral collisions, overturns, front collisions and rear collisions, the side airbags will not deploy.
Occupant protection SEAT BELT HEIGHT ADJUSTMENT FASTENING THE SEAT BELTS WARNING Insert the tongue into the buckle until you hear a distinct click. You have not fastened the seat belt properly if you do not hear a click. E87511 Note: Lifting the slider slightly while pressing the locking button makes it easier to release the locking mechanism. To raise or lower, press the locking button on the adjuster and move as necessary.
Occupant protection Deactivating the seat belt reminder See your dealer. USING SEAT BELTS DURING PREGNANCY E71313 Fitting the passenger airbag deactivation switch WARNING If you need to fit a child restraint on a seat protected by an operational airbag in front of it, have a passenger airbag deactivation switch fitted. Ask your dealer for further information. E68587 WARNING Position the seat belt correctly for your safety and that of your unborn child.
Occupant protection Disabling the passenger airbag A B E71312 A Disabled B Enabled Turn the switch to position A. When you switch the ignition on, check that the passenger airbag deactivation warning lamp illuminates. Enabling the passenger airbag WARNING Make sure that the passenger airbag is enabled when you are not using a child restraint on the front passenger seat. Turn the switch to position B.
Keys and remote controls GENERALINFORMATIONON RADIO FREQUENCIES CAUTION The radio frequency used by your remote control can also be used by other short distance radio transmissions (e.g. amateur radios, medical equipment, wireless headphones, remote controls and alarm systems). If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key. 2 1 E78284 1. Slide the release slider in the direction of the arrow. 2. Remove the key blade.
Keys and remote controls 7. Install the key blade.
Locks Note: The direction indicators will flash twice as soon as you activate central locking. They will not flash again when you press the lock button on the remote control or turn the key for the second time, i.e. when you activate double locking. LOCKING AND UNLOCKING Central locking You can only centrally lock the doors if they are all closed. Note: The driver’s door can be unlocked with the key. This needs to be used if the remote control is not functioning.
Locks Luggage compartment lid Double locking the doors and the luggage compartment lid with the remote control Opening the luggage compartment lid Press button B twice within three seconds.
Locks Reprogramming the unlocking function Opening the upper luggage compartment lid with the remote control If the unlocking function is reprogrammed so that only the driver’s door is unlocked ( See Programming the remote control (page 27). ), note the following: Press and hold button C on the remote control. Closing the luggage compartment lid When you press the unlock button either all the doors are unlocked or only the driver’s door is unlocked.
Locks WARNING The vehicle does not lock itself automatically. If no locking button is pressed, the vehicle will remain unlocked. Locking buttons are located on each of the front doors. To activate central locking and arm the alarm: • Press a locking button once. E78276 Passive locking and unlocking requires a valid passive key to be located within one of the three external detection ranges.
Locks Unlocking the vehicle If the driver’s door is the first door which is opened, the other doors and the luggage compartment lid will remain locked. All the other doors can be unlocked from inside the vehicle by using the unlock button next to the driver’s door handle. Doors can be unlocked individually by pulling the interior door handles on those doors. Note: If the vehicle remains locked for longer than three days, the key free system will enter an energy-saving mode.
Locks Locking and unlocking the doors with the key blade Global opening 2 1 E71955 E78284 To open all the windows, press and hold the unlock button for at least three seconds. Press either the lock or the unlock button again to stop the opening function. 1. Slide the release slider in the direction of the arrow and pull out the key blade with your thumb. 2. Remove the key blade and insert it into the lock. Global closing WARNING GLOBAL OPENING AND CLOSING Take care when using global closing.
Locks E99679 E87384 To close all the windows, press and hold the button on the driver’s door handle for at least two seconds. The anti-trap function is also active during global closing.
Engine immobiliser The indicator in the instrument cluster will come on for approximately three seconds and then go out. If the indicator stays on for one minute or flashes for approximately one minute and then repeatedly at irregular intervals, your key has not been recognised. Remove the key and try again. PRINCIPLE OF OPERATION The engine immobiliser is a theft protection system that prevents someone from starting the engine with an incorrectly coded key.
Alarm Unauthorised entry into the vehicle’s interior will trigger the alarm in the same way as the anti-theft system. ARMING THE ALARM The system is armed as soon as the vehicle is locked and acts as a deterrent to unauthorised persons who attempt to open the doors, bonnet or luggage compartment, or remove the audio system. The sensors are located in the interior lamp unit. All except Britain and Ireland The interior sensing alarm is armed together with the double locking system.
Alarm Britain and Ireland only If the vehicle is unlocked using the key blade, a 12 second delay chime starts as soon as the driver’s door is opened. The alarm will be deactivated during this period.
Steering wheel ADJUSTING THE STEERING WHEEL WARNING Make sure that you fully engage the locking lever when returning it to its original position. WARNING Never adjust the steering wheel when the vehicle is moving. AUDIO CONTROL Select radio, CD or cassette mode on the audio unit. Note: Make sure that you are sitting in the correct position. See Sitting in the correct position (page 90).
Steering wheel Seek • • • In radio mode, this will locate the next pre-set radio station. In CD mode, this will select the next CD if a CD changer is fitted. In all modes to abort a traffic message during broadcasting. Press and hold the button on the side: • In radio mode to change the waveband. VOICE CONTROL E78047 Move the lever up or down: • • E78049 In radio mode, this will locate the next radio station up or down the frequency band. In CD mode, it will select the next or previous track.
Wipers and washers Automatic wiper system WINDSCREEN WIPERS Some models without autowipers are fitted with a speed-dependent front screen wiper system. D C When the vehicle is slowed to walking speed or is brought to a standstill, the wiper speed will automatically switch to the next lower wiper speed setting. B When the vehicle speed is increased, the wiper speed will return to the manually-chosen setting. Moving the wiper lever when the system is operating will switch off the system.
Wipers and washers A WARNING B Do not operate the washer for more than 10 seconds at a time, and never when the reservoir is empty. While the button at the end of the lever is pressed the washer will work in conjunction with the wipers. C After releasing the button, the wipers operate for a short time.
Wipers and washers Rear window washer 2. Using a suitable implement adjust the jets. 3. Close the bonnet and check the operation of the jets. See Opening and closing the bonnet (page 142). HEADLAMP WASHERS The headlamp washers will operate with the windscreen washers when the headlamps are on. Note: To stop the washer fluid reservoir emptying quickly, the headlamp washers will not operate every time that you use the windscreen washers.
Wipers and washers CHANGING THE WIPER BLADES Windscreen wiper blades A CAUTIONS Set the windscreen wipers in the service position to change the wiper blades. You can use the service position in winter to provide easier access to the wiper blades for freeing them from snow and ice. The windscreen wipers will return to their normal position as soon as you switch on the ignition so make sure that the outside of the windscreen is free from snow and ice before you switch on the ignition. E99280 1.
Wipers and washers Rear window wiper blade 1. Lift the wiper arm. 3 4 2 E86456 2. Position the wiper blade at right angles to the wiper arm. 3. Disengage the wiper blade from the wiper arm. 4. Remove the wiper blade. Note: Make sure that the wiper blade locks into place. 5. Install in the reverse order.
Lighting Main and dipped beam LIGHTING CONTROL Lighting control positions F A B C E71095 Pull the lever fully towards the steering wheel to switch between main and dipped beam. E E71094 D Headlamp flasher Pull the lever slightly towards the steering wheel. A Off B Side and tail lamps C Headlamps D Front fog lamps E Rear fog lamps F Parking lamps Home safe lighting Switch the ignition off and pull the direction indicator lever towards the steering wheel to switch the headlamps on.
Lighting Note: You cannot switch the front fog lamps on if you have switched autolamps on. AUTOLAMPS REAR FOG LAMPS E73840 E71097 Note: If you have switched autolamps on, you can only switch the main beam on when autolamps has switched the headlamps on. WARNING Do not use the rear fog lamps when it is raining or snowing and visibility is more than 50 metres. The headlamps will come on and go off automatically depending on the ambient light.
Lighting You can adjust the level of the headlamp beams according to the vehicle load. Recommended headlamp levelling control positions Load 1 Load in luggage 1 Control position Front seats Rear seats compartment 1-2 - - 0 1-2 3 - 1 1-2 3 Max 1.5 1 - Max 3 See Vehicle identification plate (page 170). HAZARD WARNING FLASHERS E71943 For item location: See Quick start (page 8).
Lighting ADAPTIVE FRONT LIGHTING SYSTEM (AFS) A A B B E72897 A without AFS B with AFS To activate the AFS when the daytime running lamps are activated, turn the lighting control to position C. See Lighting control (page 46). The AFS adjusts the headlamp dipped beam depending on vehicle direction and speed. It improves visibility when you are driving at night and helps to reduce headlamp glare for oncoming drivers.
Lighting If you set the switch to position B, the courtesy lamp will come on when you unlock or open a door or the luggage compartment lid. If you leave a door open with the ignition switch off, the courtesy lamp will go off automatically after some time to prevent the vehicle battery from discharging. To switch it back on, switch on the ignition for a short time. DIRECTION INDICATORS The courtesy lamp will also come on when you switch off the ignition.
Lighting Vanity mirror lamps 2 A B 3 E72900 E99388 A Off B On 2. Remove the screw. 3. Using a suitable implement, remove the trim panel. If you switch off the ignition, the vanity mirror lamps will go off automatically after a short time to prevent the vehicle battery from discharging. To switch them back on, switch on the ignition for a short time. 4 REMOVING A HEADLAMP WARNING Have Xenon bulbs changed by a trained technician. There is a risk of electric shock. 1. Open the bonnet.
Lighting Headlamp 5 7 Direction indicator 1. Remove the headlamp. See Removing a headlamp (page 51). 6 2 E99390 5. Disconnect the electrical connector. 6. Disconnect the headlamp washer hose. 7. Remove the headlamp. 3 E99482 Note: When fitting the headlamp, make sure that you fully engage the headlamp in the retaining clips. 2. Turn the bulb holder anti-clockwise and remove it. 3. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
Lighting 2. Turn the bulb holder anti-clockwise and remove it. 1. Remove the cover. 3. Remove the bulb. Side lamp 1. 3 Remove the headlamp. See Removing a headlamp (page 51). 2 E99398 2. Release the retaining clip. 3. Remove the bulb and bulb holder. Remove the bulb. 2 Approach lamp 3 E99437 2. Remove the cover. 3. Pull the bulb holder and remove it. Remove the bulb. Side repeaters 1 1 E72264 Note: Position the mirror glass as far inwards as possible. 1.
Lighting 5 3 2 E72265 2. Remove the lamp. 3. Remove the bulb. 4 Front fog lamps E99406 4. Disconnect the electrical connector. 5. Turn the bulb holder anti-clockwise and remove it. Rear fog lamps 1 2 3 3 1 E99405 2 Note: You cannot separate the fog lamp bulb from the bulb holder. 1. Using a suitable implement, remove the cover. 2. Remove the screws. E107752 1. Carefully remove the lamp. 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb. 3. Remove the lamp.
Lighting Rear lamps Tail lamp and brake lamp Direction indicator and reverse lamp 1 3 E99411 1. Remove the trim panel. E99407 1. Remove the trim panel. 2 A B E99412 2. Remove the nut. E99408 A Direction indicator B Reverse lamp 2. Disconnect the electrical connector. 3. Turn the bulb holder anti-clockwise and remove it. 4. Remove the bulb.
Lighting Interior lamp Vehicles without interior sensors 2 3 1 E99413 E99452 3. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it. 1. Carefully prise out the lamp. 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb. Central high mounted brake lamp Vehicles with interior sensors Note: The LED board is not a serviceable item, please consult your dealer if this fails. 3 Number plate lamp 2 3 2 1 E72789 E72787 1.
Lighting Reading lamps Vehicles without interior sensors 2 3 E73939 1 3 3. Remove the bulb. Vanity mirror lamp E99453 1. Carefully prise out the lamp. 2. Turn the bulb holder anti-clockwise and remove it. 3. Remove the bulb. Vehicles with interior sensors E72785 1 1. Carefully prise out the lamp. 2. Remove the bulb. 2 2 E72786 1. Carefully prise out the lamp. 2. Turn the bulb holder anti-clockwise and remove it.
Lighting Luggage compartment lamp 1 1. Carefully prise out the lamp. 2. Remove the bulb. 2 E99429 BULB SPECIFICATION CHART Lamp Specification Power (watt) H21W 21 Headlamp main beam H7 55 Headlamp dipped beam H7 55 Side repeater W5W 5 Front fog lamp H8 35 W5W 5 Rear direction indicator PSY19W 19 Brake and tail lamp W21/5W 21/5 Rear fog lamp P21W 21 Reversing lamp P21W 21 1 x LED board 1.
Lighting Lamp Specification Power (watt) Festoon 10 Luggage compartment lamp 59
Windows and mirrors Opening and closing the windows automatically ELECTRIC WINDOWS WARNING Press or lift the switch to the second action point and release it completely. Press or lift it again to stop the windows. Do not operate the electric windows unless they are free from obstruction. Safety switch for rear windows Note: If you operate the switches often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating.
Windows and mirrors Overriding the anti-trap function 6. Lift and hold the switch until the window is fully closed. CAUTION 7. Open the window and try to close it automatically. While you close the window for the third time, the anti-trap function is disabled. Make sure there are no obstacles in the way of the closing window. 8. Reset and repeat procedure if the window does not close automatically. EXTERIOR MIRRORS To override this protection function when there is a resistance, e.g.
Windows and mirrors Electric folding mirrors ELECTRIC EXTERIOR MIRRORS Note: When the mirrors are operated often during a short period of time, the system may become inoperable for a period of time to prevent damage due to overheating. Note: The switch must be in position B. The electric folding mirrors operate with the ignition on. A C B E70846 A Left-hand mirror B Off C Right-hand mirror E122706 Press the button to fold or unfold the mirrors.
Instruments GAUGES A B C D E E98738 A Tachometer B Engine coolant temperature gauge C Fuel gauge D Speedometer E Information display CAUTION Engine coolant temperature gauge Do not restart the engine until the cause of overheating has been resolved. All vehicles Shows the temperature of the engine coolant. At normal operating temperature, the needle will remain in the centre section.
Instruments Airbag warning lamp If the needle enters the red section, the engine is overheating. Stop the engine, switch the ignition off and determine the cause once the engine has cooled down. See Engine coolant check (page 148). If it illuminates when you are driving, this indicates a malfunction. Have the system checked by a properly trained technician. Fuel gauge Brake system lamp The arrow adjacent to the fuel pump symbol indicates on which side of the vehicle the fuel filler cap is located.
Instruments Engine warning lamp Headlamp indicator If it illuminates with the engine running, this indicates a malfunction. If it flashes when you are driving, reduce the speed of your vehicle immediately. If it continues to flash, avoid heavy acceleration or deceleration. Have the system checked by a properly trained technician immediately. It will illuminate when you switch the headlamp dipped beam or the side and tail lamps on.
Instruments Stability control (ESP) indicator If it stays on after starting or illuminates when driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch the engine off. Check the engine oil level. See Engine oil check (page 147). While driving, it flashes during activation of the system. After switching on the ignition, if it does not illuminate or illuminates continuously while driving, this indicates a malfunction. During a malfunction, the system switches off.
Instruments Key-in-ignition Except vehicles with keyless entry A warning tone will sound when the driver’s door is opened if: • the key is in the ignition. Vehicles with keyless entry A warning tone will sound when the driver’s door is opened if: • the ignition is still on • the spare key is in the ignition. Lights on A warning chime will sound if the driver’s door is opened with the exterior lights switched on and the ignition switched off.
Information displays • GENERAL INFORMATION • WARNING Do not operate the information display controls when the vehicle is moving. to scroll through the trip computer displays to scroll through and highlight the options within a menu. Note: To scroll automatically, hold the rotary control in the upward or downward position. Note: The information display will remain on for several minutes after you switch off the ignition.
Information displays Menu structure ESP Reset Trip Trip Odo Avg Fuel Avg Speed All Messages Steering Standard Sport Comfort Clock Set Clock 24 Hour Mode Setup Display Configure A B Help Screen NAV Info C E98875 69 Always off On Guidance Always on
Information displays B C Language Measure Unit English Deutsch Italiano Français Español Türkçe Pyccкий Nederlands Polski Svenska Português Metric Imperial Chimes Low Fuel General Warn General Info Aux.
Information displays 2. Highlight ESP and press the SET/RESET. 3. Highlight Back and repeatedly press the SET/RESET button to return to the main menu. A Park Heater Time 1 on Steering Set Time 1 Monday Tuesday Wednesday Thursday Friday Saturday Sunday Time 2 on Note: For road safety reasons, changes in the Steering menu can only be made while the vehicle is stationary.
Information displays Navigation information 2. Highlight Clock and press the SET/RESET button. 3. Highlight Set Clock and press the SET/RESET button. The hours start to flash. You can also choose when the navigation information is displayed in the information display. Three options are available: • 4. Use the rotary control to adjust the hours to the desired setting. 5. Press the SET/RESET button to confirm the setting. The minutes start to flash. 6.
Information displays 1. Use the rotary control to enter the main menu. 5. Highlight the desired setting and press the SET/RESET button to confirm the setting. 2. Highlight Setup and press the SET/RESET button. 3. Highlight Display and press the SET/RESET button. 4. Highlight Language and press the SET/RESET button. 6. Highlight Back and repeatedly press the SET/RESET button to return to the main menu. Chime deactivation The following chimes can be deactivated: • Low fuel warning.
Information displays Message symbols See Owner’s handbook. Have the system checked at the next service. Have the system checked as soon as possible. E73266 Stop your vehicle as soon as it is safe to do so. Press SET/RESET to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time. Viewing current messages 1. Press the SET/RESET button to enter the main menu. 2.
Information displays Doors open Message Warning lamp Action red Vehicle is moving. Stop the vehicle as soon as safely possible and close. Driver side rear door open red Vehicle is moving. Stop the vehicle as soon as safely possible and close. Passenger door open red Vehicle is moving. Stop the vehicle as soon as safely possible and close. Passenger side rear door open red Vehicle is moving. Stop the vehicle as soon as safely possible and close. Luggage comp. open red Vehicle is moving.
Information displays Message Remote key battery low Warning lamp amber Action See Changing the remote control battery (page 27). Steering malfunction - Have the system checked by a properly trained technician. To start press brake - See Keyless starting (page 101). To start press clutch - See Keyless starting (page 101). Lighting Message Brake light fault Adaptive front light failure Warning lamp Action red Brake lamp switch. The vehicle can be driven as normal.
Information displays Message Acceleration reduced Low washer fluid level Service oil Warning lamp Action red Electronic acceleration control (EAC). The vehicle can be driven but the acceleration rate will be noticeably reduced. Maximum vehicle speed will be maintained. Have the system checked by a properly trained technician as soon as possible. amber Appears only on vehicles fitted with headlamp washers. The washer fluid level is low. Check the washer fluid level.
Information displays Transmission Message Transmission limited function Transm. too hot. Press brake Transmission too hot Transmission malfunction Warning lamp Action amber Automatic transmission. The vehicle can still be driven but have the system checked by a properly trained technician as soon as possible. red Under certain driving conditions it is possible that the clutches in the transmission can overheat.
Information displays Tyre pressure monitoring system Message Check tyre pressures Tyre Press. Sys malfunction Warning lamp Action amber The pressure in one or more tyres has dropped. Check as soon as possible. amber Permanent malfunction. Have the system checked by a properly trained technician.
Climate control Warming the interior PRINCIPLE OF OPERATION Direct the air towards your feet. In cold or humid weather conditions, direct some of the air towards the windscreen and the door windows. Outside air Keep the air intakes forward of the windscreen free from obstruction (snow, leaves etc.) to allow the climate control system to function effectively. Cooling the interior Direct the air towards your face.
Climate control Blower MANUAL CLIMATE CONTROL Air distribution control A A F B E C E75470 A D E71379 A Windscreen B Footwell and windscreen C Footwell D Face level and footwell E Face level F Face level and windscreen Off Note: If you switch the blower off, the windscreen may mist up. Recirculated air Press the button to toggle between outside air and recirculated air. Heating the interior quickly You can set the air distribution control to any position between the symbols.
Climate control Ventilation Cooling the interior quickly E71378 Set the air distribution control, blower and air vents to suit your requirements. E71381 Air conditioning Defrosting and demisting the windscreen Switching the air conditioning on and off If you turn the blower off, the air conditioning will turn off. When you turn the blower on again, the air conditioning will come on automatically.
Climate control Reducing interior air humidity E71383 AUTOMATIC CLIMATE CONTROL E91390 Note: Avoid adjusting the settings when the vehicle interior is extremely hot or cold. The automatic climate control adjusts to the current circumstances automatically. For the system to function properly, the side and centre vents should be fully open. The system controls the temperature, amount and distribution of the air flow automatically and adjusts them according to the driving and weather conditions.
Climate control To switch mono mode off Note: For information on the automatic climate control, on vehicles fitted with a combined Navigation and automatic climate control system, see separate handbook. Select a temperature for the passenger’s side with the rotary control on the passenger’s side. Mono mode will switch off and MONO disappears from the display. The temperature for the driver’s side will remain unchanged.
Climate control Air distribution To return to auto mode, press the AUTO button. To adjust air distribution, press the desired button. Any combination of settings can be selected simultaneously. Switching the air conditioning on and off E91393 A B Press the A/C button to switch the air conditioning on and off. A/C OFF appears in the display when the air conditioning is switched off.
Climate control Note: The parking heater will only operate if there is at least 7.5 litres (1.6 gallons) of fuel in the fuel tank and the ambient temperature is below 15°C (59°F). The heater will not operate if the battery is low. HEATED WINDOWS AND MIRRORS Heated windows Use the heated windows to defrost or demist the windscreen or rear window. Note: The heating depends on the outside air temperature. Note: The heated windows operate only when the engine is running.
Climate control Programming the parking heater Note: The programmed time is the time at which you wish the vehicle to be warm and ready to drive, not the time at which the heater switches on. Park Heater Program 1 Note: You must programme the times at least 70 minutes in advance of the time you wish to set. Program 2 One-Time Active now Note: You must set the time and date correctly.
Climate control 1. Use the rotary control to enter the main menu. Parkheater Program 1 2. Highlight Program 1 and press the SET/RESET button. 3. Highlight the day on which the heater should warm up the vehicle. 4. Press the SET/RESET button to confirm the selection. A cross appears in the box next to the day to show that this day is selected. 07:55 01:12:2006 5. Continue in the same way to select all the days on which the heater should warm up the vehicle. 6.
Climate control To deactivate the heater, highlight Active now and press the SET/RESET button again. Diesel auxiliary heater (depending on country) The diesel auxiliary heater (PTC electrical heater) aids in warming the engine and the vehicle interior on vehicles with a diesel engine. It is switched on or off automatically depending on the outside air temperature, the coolant temperature and the alternator load.
Seats • SITTING IN THE CORRECT POSITION • • hold the steering wheel with your arms slightly bent. bend your legs slightly so that you can press the pedals fully. position the shoulder strap of the seat belt over the centre of your shoulder and position the lap strap tightly across your hips. Make sure that your driving position is comfortable and that you can maintain full control of your vehicle.
Seats Adjusting the lumbar support MANUAL SEATS All vehicles WARNINGS Do not use any accessory seat covers that are not specifically designed for seats with side airbags. These seat covers must be fitted by properly trained technicians. Do not adjust the seats while the vehicle is moving. Moving the seats forwards or backwards E78058 Adjusting the height of the driver’s seat E70728 E70730 Pull the lever. Rock the seat to engage the catch.
Seats Adjusting the angle of the seatback When the seats are slid fully forward the seatbacks can be fully reclined.
Seats ELECTRIC SEATS 6-way electric seat E78060 93
Seats REAR SEATS CAUTION Lower the head restraints. WARNINGS When folding the seatbacks down, take care not to get your fingers caught between the seatback and seat frame. 2 2 Make sure that the seats and the seatbacks are secure and fully engaged in their catches. 1 Folding the seatbacks down 3 CAUTION Lower the head restraints. E86612 1 1. Insert your fingers between the seat cushion and seatback and fold the seat cushion forwards. 2. Press the unlock buttons down and hold them there. 3.
Seats The heated front seats are operated by rotary controls in the instrument panel. For item location: See Quick start (page 8). The maximum temperature is reached after five or six minutes. It is regulated thermostatically. The seat heating will operate only when the ignition is on.
Convenience features SUN BLINDS INSTRUMENT LIGHTING DIMMER Panoramic roof E70454 CUP HOLDERS WARNING Do not place hot drinks in the cup holders when the vehicle is moving. Seat back trays WARNING Do not use the trays when the vehicle is moving. Make sure that you secure the trays in the lowered position before setting off. E91500 The roof blind is in two sections. Pull the handle from the front or rear of the panoramic roof and fully extend the required section.
Convenience features Press the element in to use the cigar lighter. It will pop out automatically. AUXILIARY POWER SOCKETS CAUTION If you use the socket when the engine is not running, the battery may discharge. Note: You can use the socket to power 12 volt appliances that have a maximum current rating of 10 Amperes. Use only Ford accessory connectors or connectors specified for use with SAE standard sockets.
Convenience features STORAGECOMPARTMENTS CAUTIONS Do not exceed the maximum power output. If you do, the LED will flash twice. Remove the plug and re-insert Front storage compartment it. If the LED flashes 3 or 4 times, have the system checked by a properly trained technician. Note: You can use the socket to power 230 volt appliances that have a maximum rating of 150 watts. E99181 Note: Avoid keeping heat-sensitive objects and liquids in the front storage compartment.
Convenience features To gain access to the storage area, fold up the rear seat cushions. See Rear seats (page 94). TOLL READER 120 Note: Do not overload the storage areas under the rear seats. Ensure that the rear seat cushions can be folded back completely. 40 70 GLASSES HOLDER 13 E75193 E99272 On vehicles with an anti-heat windscreen, toll readers should be placed in the area as shown (all measurements shown in millimetres), otherwise communication performance with toll stations may be reduced.
Convenience features E91511 E91511 E92035 E99438 USB PORT FLOOR MATS See Using a USB device (page 202). WARNING When using the floor mats, always make sure the floor mat is properly secured using the appropriate fixings and positioned so that it does not interfere with the operation of the pedals.
Starting the engine GENERAL INFORMATION General points on starting If the battery has been disconnected the vehicle may exhibit some unusual driving characteristics for approx. 8 kilometres (5 miles) after reconnecting the battery. E85766 This is because the engine management system must realign itself with the engine. Any unusual driving characteristics during this period may be disregarded. Ignition on Press the start button once.
Starting the engine Failure to start 2. Remove the key blade. See Keyless entry (page 31). The passive starting system will not function if: • The passive key frequencies are jammed. • The passive key battery is flat. If you are unable to start your vehicle carry out the following procedure. E99586 3. Insert the key blade into the key holder. 4. With the key blade in this position you can use the start button to switch the ignition on and start your vehicle. E99666 1.
Starting the engine Regeneration • • WARNING Do not park or idle your vehicle over dry leaves, dry grass or other combustible materials. The DPF regeneration process creates very high exhaust gas temperatures and the exhaust will radiate a considerable amount of heat during and after DPF regeneration, and after you have switched the engine off. This is a potential fire hazard. SWITCHING OFF THE ENGINE Vehicles with a turbocharger CAUTION Do not switch the engine off when it is running at high speed.
Fuel and refuelling SAFETY PRECAUTIONS CAUTIONS Use diesel that meets the specification defined by EN 590, or the relevant national specification. WARNINGS Stop refuelling after the fuel nozzle stops the second time. Additional fuel will fill the expansion space in the fuel tank which could lead to fuel overflowing. Fuel spillage could be hazardous to other road users. Note: We recommend that you use only high quality fuel.
Fuel and refuelling WARNING We recommend that you wait at least 10 seconds before removing the fuel nozzle to allow any residual fuel to drain into the fuel tank. E86613 Press the flap to open it. Open the flap fully until it engages. When you insert the fuel nozzle, a spring loaded inhibitor will open if the correct size nozzle is detected. This helps to avoid filling up with the wrong fuel. E119081 WARNING Slightly raise the fuel nozzle to remove it.
Fuel and refuelling FUEL CONSUMPTION CAUTIONS Do not push-start or tow-start your vehicle. Use booster cables. See Using booster cables (page 154). The CO2 and fuel consumption figures are derived from laboratory tests according to EEC Directive 80/1268/EEC and subsequent amendments and are carried out by all vehicle manufacturers. Do not switch the ignition off when driving. They are intended as a comparison between makes and models of vehicles.
Fuel and refuelling 6-speed manual transmission - AWD Fuel consumption figures Urban Extra-urban Combined CO2 emissions l/100 km (mpg) l/100 km (mpg) l/100 km (mpg) g/km 2.0L Duratorq-TDCi stage IV 8.1 (34.9) 5.4 (52.3) 6.4 (44.1) 169 2.0L Duratorq-TDCi stage V 7.6 (37.2) 5.1 (55.4) 6.0 (47.1) 159 2.5L Duratec 13.9 (20.3) 7.6 (37.2) 9.9 (28.
Transmission MANUAL TRANSMISSION CAUTION Do not engage reverse gear when the vehicle is moving. This can cause damage to the transmission. N Neutral D Drive S Sport mode and manual shifting WARNING Apply the brakes before moving the selector lever and keep them applied until you are ready to move off. Note: A cold engine has a higher idle speed. This will increase the tendency for your vehicle to creep when you have selected a drive gear.
Transmission Reverse Gears may be skipped by moving the selector lever repeatedly at short intervals. WARNING Manual mode also provides a kickdown function. See Kickdown. Select reverse only when your vehicle is stationary and the engine is at idle speed. Sport mode and manual shifting - Vehicles with a 6 speed transmission Neutral Note: A shift will occur only when the vehicle speed and the engine speed are appropriate.
Transmission Hints on driving with an automatic transmission 3 Moving off 4 1. Release the parking brake. 2. Release the brake pedal and press the accelerator pedal. Stopping 2 1 1. Release the accelerator pedal and press the brake pedal. 2. Apply the parking brake. Kickdown Press the accelerator pedal fully with the selector lever in the drive position to select the next lowest gear for optimum performance. Release the accelerator pedal when you no longer require kickdown.
Transmission ALL-WHEEL DRIVE (AWD) CAUTION A vehicle fitted with AWD must be recovered with either ALL wheels on the ground or ALL wheels off the ground. See Vehicle recovery (page 140). The AWD system, fitted to certain front-wheel drive variants, will automatically provide driving torque to the rear wheels when road conditions become slippery with rain, snow or ice etc.
Brakes PRINCIPLE OF OPERATION PARKING BRAKE Disc brakes All vehicles Wet brake discs result in reduced braking efficiency. Dab the brake pedal when driving from a car wash to remove the film of water. WARNING Vehicles with an automatic transmission should always be left with the selector lever in position P. ABS • • WARNING The ABS does not relieve you of your responsibility to drive with due care and attention.
Stability control PRINCIPLE OF OPERATION Stability control (ESP) warning lamp Electronic stability programme (ESP) The ESP warning lamp will flash when the system is operating. See Warning lamps and indicators (page 64). WARNING Emergency brake assist ESP does not relieve you of your responsibility to drive with due care and attention. WARNING Emergency brake assist does not relieve you of your responsibility to drive with due care and attention.
Stability control To turn the system off and on. See Information displays (page 68).
Parking aid Note: The parking aid may emit false tones if it detects a signal using the same frequency as the sensors or if the vehicle is fully laden. PRINCIPLE OF OPERATION WARNING The parking aid does not relieve you of your responsibility to drive with due care and attention. Note: The outer sensors may detect the side walls of a garage. If the distance between the outer sensor and the side wall remains constant for three seconds, the tone will switch off.
Parking aid Note: If a high pitch warning tone sounds for three seconds and the light in the switch is flashing, it indicates a malfunction. The system will be disabled. Have the system checked by properly trained technicians. You will hear an intermittent tone at a distance of up to approximately 150 centimetres (59 inches) between the obstacle and rear bumper, 80 centimetres (31 inches) between the obstacle and front bumper and 50 centimetres (20 inches) to the side.
Rear view camera The camera is located on the luggage compartment lid near the handle. PRINCIPLE OF OPERATION The camera is a visual aid for use when reversing. WARNING The camera does not relieve you of your responsibility to drive with due care and attention. CAUTIONS If you use a high pressure spray to wash your vehicle, only spray the camera briefly from a distance not less than 20 centimetres (8 inches). Do not apply pressure to the camera.
Rear view camera D CAUTIONS Marks are for general guidance only, and are calculated for vehicles in maximum load conditions on an even road surface. E D C C B B A A The lines show a projected vehicle path (based on the current steering wheel angle) and the distance from the exterior mirrors and rear bumper. E99458 118 A Exterior mirror clearance - 0.1 metre (4 inches) B Red - 0.
Rear view camera D Amber - 2 metres (79 inches) E Amber - centre line of the projected vehicle path Note: When reversing with a trailer, the lines on the screen show the vehicle direction and not the trailer. Deactivating the rear view camera Note: Disengage reverse gear. The display will stay on for a short period before switching off. The system will automatically switch off once the vehicle speed has reached approximately 15 km/h (9 mph).
Cruise control Setting a speed PRINCIPLE OF OPERATION Cruise control allows you to control your speed using the switches on the steering wheel. You can use cruise control when you exceed approximately 30 km/h (20 mph). USING CRUISE CONTROL WARNING Do not use cruise control in heavy traffic, on twisty roads or when the road surface is slippery. E75452 Switching cruise control on Press to store and maintain your current speed. The cruise control indicator will illuminate.
Cruise control Resuming the set speed A B E95393 A Accelerate E75453 B Decelerate The cruise control indicator will illuminate and the system will attempt to resume the speed that you previously set. Cancelling the set speed Switching cruise control off E75453 Press the brake pedal or the RES switch. E75455 Note: The system will no longer control your speed. The cruise control indicator will not illuminate but the system will retain the speed that you previously set.
Load carrying GENERAL INFORMATION WARNINGS Use load securing straps to an approved standard, e.g. DIN. Make sure that you secure all loose items properly. Place luggage and other loads as low and as far forward as possible within the luggage or loadspace. Do not drive with the tailgate or rear door open. Exhaust fumes may enter the vehicle. E97377 LUGGAGE ANCHOR POINTS Do not exceed the maximum front and rear axle loads for your vehicle. See Vehicle identification (page 170).
Load carrying E112588 To remove or install the cover, push either end of the case inwards. E112571 Pull out the cover until it locks. Stowing the luggage cover vehicles with tyre repair kit Space is provided under the luggage compartment floor. REAR UNDER FLOOR STORAGE WARNING When you are using a child seat with a support leg, make sure that you install the foam spacer correctly inside the storage compartment and that you position the cover correctly.
Load carrying Installing the crossbars WARNING Distribute the load evenly over the loading area and keep the centre of gravity as low as possible. Secure the load well to prevent it from slipping. Never place any loads directly onto the roof surface. CAUTION Remove the crossbars before entering an automatic car wash. E78097 Note: The side mounting tracks are designed such that crossbars (for bicycle carriers, ski carriers etc.) from the Ford accessories range can be fitted.
Load carrying 2 1 E98207 1. Pull the handle out. 2. Turn the handle clockwise to bring the crossbar in contact with the rail. E98208 4. Push the handle in. Turn the key clockwise to lock. 5. Remove the key. Accessing the T-notch A 3 3 1 E98222 Note: Make sure there is no gap between crossbar and rail (A). 2 E98209 3. Turn the handle a minimum of 3.5 revolutions. 1. Pull the handle out. 2. Lower the cover. 3. Remove the sliding bar.
Load carrying E99775 126
Towing In high altitude regions above 1 000 metres (3 281 feet), the stipulated maximum permitted gross train weight must be reduced by 10% for every additional 1 000 metres (3 281 feet). TOWING A TRAILER WARNINGS Do not exceed the maximum gross train weight stated on the vehicle identification plate. See Vehicle identification (page 170). Steep gradients WARNING Do not exceed 100 km/h (62 mph). The overrun brake on a trailer is not controlled by ABS. The rear tyre pressures must be increased by 0.
Towing Unlocking the tow ball arm mechanism 1 2 2 1 3 E99477 1. Detach the keyhole protective cap. 2. Insert the key and turn it anti-clockwise to unlock (1). 3. Hold the tow ball arm. Pull the handwheel out and turn it clockwise until it clicks (2). 4. The red mark on the handwheel must align with the white mark on the tow ball. 5. Release the handwheel. The tow ball arm is unlocked. E99484 1. Pull out the plug (1). 2. Insert the tow ball arm vertically and press it upwards until it engages (2).
Towing Driving with a trailer A 4 3 B E71331 WARNING 1 If any of the below conditions cannot be met, do not use the tow bar and have it checked by a properly trained technician. E99485 Before starting your journey, make sure that the tow ball arm is properly locked. Check: • • • • 2 1. Unhitch the trailer. 2. Detach the keyhole protective cap. 3. Insert the key and turn it anti-clockwise to unlock (1). 4. Hold the tow ball arm.
Towing Keep the system clean. Periodically lubricate bearings, sliding surfaces, and locking balls with resin-free grease or oil and the lock with graphite. Keep a note of the key number. In case of loss, replacement keys are available from the manufacturer by stating the three digit key number.
Driving hints RUNNING-IN DRIVING THROUGH WATER Tyres Driving through water WARNING CAUTIONS Drive through water in an emergency only, and not as part of normal driving. New tyres need to be run-in for approximately 500 kilometres (300 miles). During this time, you may experience different driving characteristics. Engine damage can occur if water enters the air filter.
Emergency equipment FIRST AID KIT Space is provided in the under floor storage compartment. See Rear under floor storage (page 123). WARNING TRIANGLE Space is provided in the under floor storage compartment. See Rear under floor storage (page 123).
Status after a collision • FUEL CUT-OFF SWITCH Vehicles with a Duratec engine • E72531 The fuel supply may be cut off as a result of an accident or sudden vibrations (e.g. collision when parking). The switch is located in the side panel in front of the driver's door. Resetting the switch WARNING Do not reset the fuel cut-off switch if you see or smell leaking fuel. • • • Turn the ignition switch to position 0. Check fuel system for leaks.
Fuses FUSE BOX LOCATIONS Install in the reverse order. Engine compartment fuse box CHANGING A FUSE WARNINGS Do not modify the electrical system of your vehicle in any way. Have repairs to the electrical system and the replacement of relays and high current fuses carried out by properly trained technicians. Switch the ignition and all electrical equipment off before touching or attempting to change a fuse. CAUTION E78332 Fit a replacement fuse with the same rating as the one you have removed.
Fuses FUSE SPECIFICATION CHART Engine compartment fuse box 29 36 28 35 6 16 19 2 8 1 E79716 Fuse Ampere rating 1 40 Cooling fan 2 80 Power steering 3 60 Passenger junction box supply 1 4 60 Passenger junction box supply 2 5 80 PTC heater 6 60 Glow plugs (diesel only) 7 30 ESP pump 8 20 ESP valves 9 20 Powertrain control module 10 30 Climate control blower 11 20 Ignition switch Circuits protected 135 27 15 3 7 32 25 31 13 11 20 9 33 30 4 26 22 24
Fuses Fuse Ampere rating 12 40 Ignition relay 15l 13 20 Starter solenoid 14 40 Heated windscreen, right-hand side 15 - 16 40 17 - 18 30 Power converter 19 10 ESP module 20 15 Horn 21 20 Auxiliary heater 22 10 Power steering module 23 30 Headlamp washer 24 15 Diesel fuel heater 25 10 Ignition, relays 26 15 Automatic transmission 27 10 Air conditioning clutch 28 10 Glow plug monitoring (diesel only) 29 10 Dual zone climate control 30 3 Powertrain control
Fuses Passenger compartment fuse box 129 135 100 101 136 123 132 130 138 141 139 142 140 143 131 127 128 134 133 137 124 125 121 122 126 117 118 115 116 120 119 111 112 106 107 109 110 108 113 104 114 103 105 102 E88709 Fuse Ampere rating Circuits protected 100 10 Electronic modules ignition supply 101 20 Driver’s electric seat 102 10 Heater control, remote control receiver 103 10 Lighting control battery supply 104 10 Battery saver, interior lamps 105
Fuses Fuse Ampere rating Circuits protected 110 10 Daytime running lamps ignition supply to lighting control switch 111 5 Fuel pump (diesel only) 111 15 Fuel pump (petrol only) 112 15 Audio modules battery supply 113 10 Daytime running lamps (parking lamps) 114 10 Instrument cluster ignition supply, engine immobiliser 115 7.5 Lighting control ignition supply 116 20 Fog lamps 117 7.
Fuses Fuse Ampere rating 127 - Not used 128 - Not used 129 20 Windscreen wipers 130 10 AWD module 131 15 Rear window wiper 132 15 Brake lamps 133 25 Central locking relays, passenger door module 134 20 Central locking relays, driver door module 135 20 Daytime running lamps 136 15 Washer pump, heated washer jets 137 10 Battery backup sounder 138 10 Powertrain control module, accelerator pedal, automatic transmission, keyless module IGN monitor 139 10 Main beam right-ha
Vehicle recovery Towing eye location TOWING POINTS Front towing eye E99490 E99468 Rear towing eye The screw-in towing eye is located in the luggage compartment next to the spare wheel well. The towing eye must always be carried in the vehicle. Prise off the cover and install the towing eye. CAUTION The screw-in towing eye has a left-hand thread. Turn it anti-clockwise to install it.
Vehicle recovery WARNINGS The brake servo and the power steering pump do not operate unless the engine is running. Press the brake pedal harder and allow for increased stopping distances and heavier steering. CAUTIONS In the event of a mechanical failure of the transmission the drive wheels must be lifted clear of the ground. Do not tow your vehicle if the ambient temperature is below 0ºC (32ºF). CAUTIONS Too much tension in the tow rope could cause damage to your vehicle or the vehicle that is towing.
Maintenance Check when refuelling GENERAL INFORMATION • Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford Authorised Repairers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialised tools developed specifically for servicing your vehicle.
Maintenance 1 5 4 E78141 2 3 E78142 E78143 Closing the bonnet Note: Make sure that the bonnet is closed properly. Lower the bonnet and allow it to drop from under its own weight for the last 20 – 30 centimetres (8 - 12 inches).
Maintenance ENGINE COMPARTMENT OVERVIEW - 2.5L DURATEC (VI5) A B C D E I F H G E78890 * A Screen washer fluid reservoir : See Washer fluid check (page 149). B Engine coolant reservoir : See Engine coolant check (page 148). C Brake and clutch fluid reservoir (right-hand drive) : See Brake and clutch fluid check (page 149). D Engine oil filler cap : See Engine oil check (page 147). E Brake and clutch fluid reservoir (left-hand drive) : See Brake and clutch fluid check (page 149).
Maintenance G Engine compartment fuse box: See Fuses (page 134). H Air cleaner: No maintenance necessary. I Engine oil dipstick : See Engine oil check (page 147). * * For easy identification, filler caps and the engine oil dipstick are marked in colour. ENGINE COMPARTMENT OVERVIEW - 2.
Maintenance A B E D C I F H G E125377 * A Screen washer fluid reservoir : See Washer fluid check (page 149). B Engine coolant reservoir : See Engine coolant check (page 148). C Brake and clutch fluid reservoir (right-hand drive) : See Brake and clutch fluid check (page 149). D Engine oil filler cap : See Engine oil check (page 147). E Brake and clutch fluid reservoir (left-hand drive) : See Brake and clutch fluid check (page 149). F Battery: See Vehicle battery (page 154).
Maintenance H Air cleaner: No maintenance necessary. I Engine oil dipstick : See Engine oil check (page 147). * * For easy identification, filler caps and the engine oil dipstick are marked in colour. ENGINE OIL DIPSTICK - 2.5L DURATEC (VI5) A ENGINE OIL CHECK CAUTION Do not use oil additives or other engine treatments. Under certain conditions, they could damage the engine. B Note: The oil consumption of new engines reaches its normal level after approximately 5 000 kilometres (3 000 miles).
Maintenance Topping up Topping up WARNINGS Only top up when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down. WARNINGS Only top up when the engine is cold. If the engine is hot, wait 10 minutes for the engine to cool down. Do not remove the filler cap when the engine is running. Do not remove the filler cap when the engine is running. Do not remove the filler cap when the engine is hot. Wait for the engine to cool down. Remove the filler cap.
Maintenance BRAKE AND CLUTCH FLUID CHECK CAUTION Make sure that the level is between the MIN and the MAX marks. WARNINGS Do not allow the fluid to touch your skin or eyes. If this happens, rinse the affected areas immediately with plenty of water and contact your doctor. If the level is at the MIN mark, top up immediately. Topping up If the level is at the MIN mark, have the system checked by a properly trained technician as soon as possible. Remove the filler cap.
Maintenance TECHNICAL SPECIFICATIONS Vehicle fluids Item Recommended fluid * Specification Engine oil Castrol Engine Oil Power steering fluid Ford or Motorcraft Power Steering Fluid WSS-M2C204-A2 Coolant Motorcraft SuperPlus Antifreeze WSS-M97B44-D Brake fluid Ford or Motorcraft Super DOT 4 Brake Fluid WSS-M2C913-C ESD-M6C57-A * Providing it meets the specification defined by WSS-M2C913-C, you can also use Ford Engine Oil or an alternative engine oil.
Maintenance Variant Item Capacity in litres (gallons) 2.0L Duratorq-TDCi Engine oil - with filter 5.5 (1.2) 2.0L Duratorq-TDCi Engine oil - without filter 5.0 (1.1) 2.5L Duratec Engine oil - with filter 5.8 (1.3) 2.5L Duratec Engine oil - without filter 5.5 (1.
Vehicle care Cleaning the chrome trim CLEANING THE EXTERIOR CAUTION WARNING Do not use abrasives or chemical solvents. Use soapy water. If you use a car wash with a waxing cycle, make sure that you remove the wax from the windscreen. Body paintwork preservation CAUTIONS Prior to using a car wash facility check the suitability of it for your vehicle. CAUTIONS Do not polish your vehicle in strong sunshine. Do not allow polish to touch plastic surfaces. It could be difficult to remove.
Vehicle care Instrument cluster screens, LCD screens, radio screens WARNING Do not use abrasives, alcoholic solvents or chemical solvents to clean them. REPAIRING MINOR PAINT DAMAGE CAUTION Remove apparently harmless looking substances from the paintwork immediately (e.g. bird droppings, tree resins, insect remains, tar spots, road salt and industrial fall out). You should repair paintwork damage caused by stones from the road or minor scratches as soon as possible.
Vehicle battery To connect the booster cables USING BOOSTER CABLES CAUTIONS Connect batteries with only the same nominal voltage. Always use booster cables with insulated clamps and adequate size cable. Do not disconnect the battery from the vehicle’s electrical system.
Vehicle battery 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine and any electrical equipment. 3. Connect the positive (+) terminal of vehicle B with the positive (+) terminal of vehicle A (cable C). 4. Connect the negative (-) terminal of vehicle B to the ground connection on the left-hand side suspension turret of vehicle A (cable D). CAUTIONS Do not connect to the negative (–) terminal of the flat battery. Make sure that the cables are clear of any moving parts.
Wheels and tyres GENERAL INFORMATION WARNINGS Do not use snow chains on this type of wheel. CAUTIONS Use only approved wheel and tyre sizes. Using other sizes could damage the vehicle and will make the National Type Approval invalid. Do not drive through an automatic car wash. Do not carry out any tyre repairs on a temporary spare wheel. If you change the diameter of the tyres from that fitted at the factory, the speedometer may not display the correct speed.
Wheels and tyres Jacking and lifting points Vehicles without tyre repair kit or run flat tyres CAUTION Your vehicle jack, wheel brace, screw-in towing eye and wheel trim remover are located in the spare wheel well. Use only the specified jacking points. If you use other positions, you may damage the body, steering, suspension, engine, braking system or the fuel lines.
Wheels and tyres Vehicles with side skirts A E93184 Indentations in the sills A show the location of the jacking points. E95345 Assembling the wheel brace Type one WARNING When returning the wheel brace extension to its original position, take care not to get your fingers caught. Note: Make sure that the wheel brace is fully extended. E92932 E122546 Extend the wheel brace. Type two CAUTION The screw-in towing eye has a left-hand thread. Turn it anti-clockwise to install it.
Wheels and tyres Removing a road wheel WARNINGS Park your vehicle in such a position that neither the traffic nor you are hindered or endangered. Set up a warning triangle. Make sure that the vehicle is on firm, level ground with the wheels pointing straight ahead. E122502 Insert the screw-in towing eye into the wheel brace. Switch off the ignition and apply the parking brake. Removing the wheel trim If your vehicle has a manual transmission, select first or reverse gear.
Wheels and tyres Note: The spare wheel is located under the floor cover in the luggage compartment. 1. WARNINGS Do not fit run flat tyres on vehicles that were not originally fitted with them. Please contact your dealer for more details regarding compatibility. Install the locking wheel nut key. CAUTION Do not install alloy wheels using wheel nuts designed for use with steel wheels. Note: Make sure the wheel and hub contact surfaces are free from foreign matter.
Wheels and tyres 7. Install the wheel trim using the ball of your hand. The tyre repair kit seals most tyre punctures [with a diameter of up to six millimetres (1/4 inch)] to temporarily restore mobility. WARNING Have the wheel nuts checked for tightness and the tyre pressure checked as soon as possible. Observe the following rules when using the kit: • Note: If the spare wheel is different in size or construction to the road wheels, have this replaced as soon as possible.
Wheels and tyres • • • • • • Park your vehicle at the roadside so that you do not obstruct the flow of traffic and so that you are able to use the kit without being in danger. Apply the parking brake, even if you have parked on a level road, to make sure that the vehicle will not move. Do not attempt to remove foreign objects like nails or screws penetrating the tyre.
Wheels and tyres A K H C D E94973 F A Protective cap B Pressure relief valve C Hose D Orange cap E Bottle holder F Pressure gauge G Power plug with cable H Compressor switch I Label K Sealant bottle 3. Take the hose C and the power plug with cable G out of the kit. 4. Unscrew the orange cap D and the bottle lid J. 5. Screw the sealant bottle K clockwise into the bottle holder E fully tight. 6. Remove the valve cap from the damaged tyre. 7.
Wheels and tyres 14. Quickly unscrew the hose C from the tyre valve and replace the protective cap A. Fasten the valve cap again. 15. Leave the sealant bottle K in the bottle holder E. Make sure the kit, the bottle lid and the orange cap are stored safely, but still easily accessible in the vehicle. The kit will be required again when you check the tyre pressure. Immediately drive approximately three kilometres (two miles) so that the sealant can seal the damaged area. 16. 17. 4.
Wheels and tyres When a standard tyre experiences a drastic loss of inflation pressure, the rim of the wheel brings the full weight of the vehicle to bear on the collapsed sidewalls. You can barely manoeuvre the vehicle and the tyre is destroyed. RUN FLAT TYRES Principle of operation Standard tyre A Run flat tyres have sturdy, reinforced sidewalls that support the rim should the tyre suffer a loss of inflation pressure.
Wheels and tyres Examine the tyres regularly for cuts, foreign objects and uneven wear of the tread. Uneven wear could mean that the wheel alignment is outside specification. WARNINGS Do not fit a mixture of run flat and standard tyres. In isolated cases, a standard tyre can be temporarily mounted on a vehicle otherwise equipped with run flat tyres. It must be pointed out to the driver that the standard tyre has no runflat properties.
Wheels and tyres Vehicles with stability control (ESP) Apart from a too low tyre pressure or a damaged tyre, the following situations can affect the rolling circumference: • Vehicle load is uneven. • When using a trailer or travelling up and down an incline. • Using snow chains. • Driving on soft surfaces such as snow or mud. Vehicles with stability control (ESP) may exhibit some unusual driving characteristics which can be avoided by switching the system off. See Using stability control (page 113).
Wheels and tyres 2. Press and hold the SET/RESET button until the message Tyre Pressure set appears. TECHNICAL SPECIFICATIONS Wheel nut torque Wheel type Nm (Ib-ft) All 130 (96) Tyre pressures (cold tyres) Up to 80 km/h (50 mph) Tyre pressures Normal load Variant All Tyre size T135/90 R 17 Full load Front Rear Front Rear bar (lbf/in²) bar (lbf/in²) bar (lbf/in²) bar (lbf/in²) 4.2 (61) 4.2 (61) 4.2 (61) 4.
Wheels and tyres Continuous speed in excess of 160 km/h (100 mph) Tyre pressures Normal load Variant Tyre size Full load Front Rear Front Rear bar (lbf/in²) bar (lbf/in²) bar (lbf/in²) bar (lbf/in²) All 215/65 R16 2.3 (33) 2.3 (33) 2.4 (35) 2.8 (41) All 235/60 R16 2.3 (33) 2.3 (33) 2.4 (35) 2.8 (41) All 235/55 R17 2.3 (33) 2.3 (33) 2.4 (35) 2.8 (41) All 235/55 RF17 2.3 (33) 2.3 (33) 2.4 (35) 2.8 (41) All 235/50 R18 2.3 (33) 2.3 (33) 2.4 (35) 2.
Vehicle identification VEHICLE IDENTIFICATION PLATE B A E VEHICLE IDENTIFICATION NUMBER (VIN) D C E85610 E87496 A Vehicle identification number B Gross vehicle weight C Gross train weight D Maximum front axle weight E Maximum rear axle weight The vehicle identification number is stamped into the floor panel on the right-hand side, beside the front seat. It is also shown on the left-hand side of the instrument panel.
Technical specifications TECHNICAL SPECIFICATIONS Vehicle dimensions D A C E B E99435 Item Dimension description Dimension in mm (inches) A Maximum length 4 443 (174.9) B Overall width including exterior mirrors 2 128 (83.
Technical specifications Item C Dimension description Dimension in mm (inches) Overall height at EC kerb weight without roof bars 1 655 - 1 677 (65.2 - 66) Overall height at EC kerb weight with roof bars 1 687 - 1 710 (66.4 67.3) D Wheelbase 2 690 (105.9) E Front track 1 574 - 1 580 (62 - 62.2) Rear track 1 584 - 1 590 (62.4 62.
Technical specifications Towing equipment dimensions A B C E D F G E99436 173
Technical specifications Item Dimension description Dimension in mm (inches) A Bumper – end of tow ball 98 (3.9) B Attachment point – centre of tow ball 87 (3.4) C Wheel centre – centre of tow ball 918 (36.1) D Centre of tow ball – side member 518 (20.4) E Outer side of side member 1 031 (40.6) F Centre of tow ball – centre of first attachment point 446 (17.6) G Centre of tow ball – centre of second attachment point 746 (29.
Telephone Phonebook categories GENERAL INFORMATION Depending on your phonebook entry, different categories can be displayed in the audio unit. CAUTION Using the system with the engine off will drain the battery. For example: This section describes the functions and features of the Bluetooth mobile phone hands free system. M Mobile O Office The Bluetooth mobile phone part of the system provides interaction with the audio or navigation system and your mobile phone.
Telephone Select the phone from the active phone menu. Requirements for Bluetooth connection Turning the ignition and radio or navigation unit back on again, the last active phone is picked up by the system. The following are required before a Bluetooth phone connection can be made. Note: In some cases the Bluetooth connection must also be confirmed on the phone. 1. Bond another Bluetooth phone Bond a new Bluetooth phone as described in the requirements for a Bluetooth connection. 2.
Telephone TELEPHONE CONTROLS Making a call Remote control Dialling a number using voice control Voice and mode button Phone numbers can be dialled using voice control. See Telephone commands (page 192). 1 Dialling a number using the address book You can access your phone address book via Bluetooth. The entries will appear in the unit display. 1. 2 2. Press the MENU button. 3. Keep pressing the MENU button until PHONEBOOK appears. 4. Press the seek buttons to select the desired phone number.
Telephone Dialling a number using the telephone keypad Redialling a number - Sony radio 1. If you have an audio unit with a telephone keypad (buttons 0-9, * and #): Press the PHONE or the call accept button. 2. Press the seek button until the desired list is displayed. 1. Press the call accept button. Press the PHONE button if you have a Sony radio. 2. Dial the number using the telephone keypad on the audio unit.
Telephone Accepting a second incoming call Using the audio unit menu Second incoming calls can be accepted by pressing either the call accept button, the PHONE button, or the MODE button on the remote control. Note: After bonding a phone to the system, this becomes the active phone. Rejecting a second incoming call 2. Press the MENU button on the audio unit. 1. Second incoming calls can be rejected by pressing the call reject button.
Telephone Rejecting an incoming call 3. Scroll through the different phones by using the seek buttons and display the phone to be debonded. 4. Press the OK button to be debond. Incoming calls can be rejected by pressing either the call reject button, the CD or AM/FM buttons on the unit, or by using the REJECT option in the menu. USING THE TELEPHONE VEHICLES WITH: NAVIGATION SYSTEM Receiving a second incoming call Note: The second incoming call function must be activated in your phone.
Telephone CD navigation units Press the microphone mute button. Press the button once again to turn this function off. Changing the active phone Note: Phones must be bonded to the system before they can be made active. Note: After bonding a phone to the system, this becomes the active phone. 1. Press the PHONE button on the unit. 2. Using the BT SETTINGS option in the menu, select the active phone from the list.
Voice control Do not try to give any commands until the beep tone has been heard. The voice control system will repeat each spoken command back to you. PRINCIPLE OF OPERATION CAUTION Using the system with the engine off will drain the battery. If you are not sure how to continue say "HELP" for assistance or "CANCEL" if you do not wish to continue.
Voice control • • • • • Name tag automatic climate control: "TEMPERATURE", "AUTO MODE", "DEFROSTING/DEMISTING ON" and "DEFROSTING/DEMISTING OFF" radio: "TUNE NAME" external device (USB): "TRACK" external device (iPod): "TRACK" SD card: "TRACK". The name tag functionality can support the phone, audio and navigation features by using the "STORE NAME" function. You can assign name tags to items such as favourite radio stations and personal phone contacts. See Audio unit commands (page 183).
Voice control "CD PLAYER" "REPEAT TRACK" "REPEAT OFF" * Can be used as a shortcut. ** Only available if the CD contains audio data files like MP3 or WMA. Track You can choose a track on your CD directly. Steps User says System answer 1 "CD PLAYER" "CD PLAYER" 2 "TRACK" 3 "" "TRACK NUMBER PLEASE" * ** "TRACK " * Can be used as a shortcut.
Voice control "CD CHANGER" "HELP" "PLAY" * "DISC" "TRACK" * "SHUFFLE ALL" "SHUFFLE CD" "SHUFFLE FOLDER" ** "SHUFFLE OFF" "REPEAT CD" "REPEAT FOLDER" ** "REPEAT TRACK" "REPEAT OFF" * Can be used as a shortcut. ** Only available if the CD contains audio data files like MP3 or WMA. Disc If you have a CD changer you can choose the disc number.
Voice control Steps User says System answer 1 "CD CHANGER" "CD CHANGER" 2 "TRACK" 3 "" "TRACK NUMBER PLEASE" * "TRACK " ** * Can be used as a shortcut. ** Additionally, numbers can be spoken as up to four single digits (for example "2", "4", "5" for track 245) Shuffle CD To set random playback within the CD contents.
Voice control "RADIO" "PLAY" * Can be used as a shortcut. Tune frequency This function allows you to tune your radio by voice commands. Steps User says System answer 1 "RADIO" "RADIO" 2 "AM" "AM FREQUENCY PLEASE" "FM" "FM FREQUENCY PLEASE" 3 "TUNE " * "" * The frequency may be entered in a variety of ways. Refer below for representative examples. • • • • • FM band: 87.5 - 108.0 in increments of 0.1 • • • • • "Eighty nine point nine" (89.9) "Ninety" (90.
Voice control Tune name This function allows you to call up a stored radio station. Steps User says System answer 1 "RADIO" "RADIO" 2 "TUNE NAME" "NAME PLEASE" 3 "" "TUNE " * * Can be used as a shortcut. Delete name This function allows you to delete a stored radio station.
Voice control Steps User says System answer 1 "RADIO" "RADIO" 2 "DELETE DIRECTORY" "DELETE DIRECTORY" "CONFIRM YES OR NO" 3 "YES" "RADIO DIRECTORY DELETED" "NO" "COMMAND CANCELLED" Play This function switches the audio source to the radio mode. Steps User says System answer 1 "RADIO" "RADIO" 2 "PLAY" Auxiliary input This function allows you to switch the audio source to the attached auxiliary input device.
Voice control "EXTERNAL DEVICE", "USB" "PLAY" "TRACK" * ** "PLAYLIST" "FOLDER" ** "SHUFFLE ALL" "SHUFFLE FOLDER" "SHUFFLE PLAYLIST" "SHUFFLE OFF" "REPEAT TRACK" "REPEAT FOLDER" "REPEAT OFF" * Can be used as a shortcut. ** Playlists and folders activated by voice control must be assigned special filenames. See General information (page 200). USB play This function allows you to switch the audio source to the attached USB device.
Voice control Steps User says System answer 1 "EXTERNAL DEVICE" "EXTERNAL DEVICE" 2 "USB" "USB" 3 "TRACK" "TRACK NUMBER PLEASE" 4 "" * "TRACK " * Additionally, numbers can be spoken as up to four single digits (for example "2", "4", "5" for track 245) Overview External devices - iPod The overview below shows the available voice commands. The following lists will give further information about the complete command menu in selected examples.
Voice control iPod Track You can choose a track off the all titles list of your iPod directly. Steps User says System answer 1 "EXTERNAL DEVICE" "EXTERNAL DEVICE" 2 "IPOD" "IPOD" 3 "TRACK" 4 "" "TRACK NUMBER PLEASE" * "TRACK " ** * Can be used as a shortcut. ** Additionally, numbers can be spoken as up to five single digits (for example "5", "2", "4", "5", "3" for track 52453), to a limit of 65535.
Voice control "PHONE" "HELP" * "MOBILE NAME" "DIAL NUMBER" * * "DIAL NAME" "DELETE NAME" "DELETE DIRECTORY" "PLAY DIRECTORY" "STORE NAME" * "REDIAL" "ACCEPT CALLS" "REJECT CALLS" * Can be used as a shortcut. Phone functions Dial number Phone numbers can be dialled after giving the name tag voice command.
Voice control Dial name Phone numbers can be dialled after giving the name tag voice command. Steps User says System answer 1 "PHONE" "PHONE" 2 "DIAL NAME" "NAME PLEASE" 3 "" "DIAL " "CONFIRM YES OR NO" 4 "YES" "DIALLING" "NO" "COMMAND CANCELLED" * * Can be used as a shortcut. Redial This function allows you to redial the last dialled phone number.
Voice control Steps 2 User says "MOBILE NAME" System answer "MOBILE NAME" "" * * Can be used as a shortcut. Note: DTMF can only be used during an ongoing call. Press the VOICE button and wait for the system prompt. DTMF (Tone dialling) This function transfers spoken numbers into DTMF tones. For example, to make a remote enquiry to your home answering machine or to enter a PIN number etc. Steps Can only be used with vehicles installed with a dedicated VOICE button.
Voice control Delete name Stored names can also be deleted from the directory. Steps User says System answer 1 "PHONE" "PHONE" 2 "DELETE NAME" "NAME PLEASE" 3 "" "DELETE " "CONFIRM YES OR NO" 4 "YES" " DELETED" "NO" "COMMAND CANCELLED" Play directory Use this function to let the system tell you all stored entries.
Voice control Main settings Calls can be set to be automatically rejected using voice control. Reject calls Steps User says System answer 1 "PHONE" "PHONE" 2 "REJECT CALLS" "REJECT CALLS" "ACCEPT CALLS" * "ACCEPT CALLS" * use this command to turn the reject mode off CLIMATE CONTROL COMMANDS NAVIGATION SYSTEM COMMANDS Climate Please refer to your separate Navigation handbook for details of the command menus.
Voice control "CLIMATE" "AUTO MODE" * * Can be used as a shortcut. On vehicles fitted with an English language module the "FAN" shortcut is not available. Fan This function allows you to adjust the fan speed. Steps User says System answer 1 "CLIMATE" "CLIMATE" 2 "‘FAN" "FAN SPEED PLEASE" "MINIMUM" "FAN MINIMUM" "" "FAN " "MAXIMUM" "FAN MAXIMUM" 3 * * Can be used as a shortcut.
Voice control Steps User says System answer 1 "CLIMATE" "CLIMATE" 2 "TEMPERATURE" "TEMPERATURE PLEASE" "MINIMUM" "TEMPERATURE MINIMUM" "" or "" "TEMPERATURE " "MAXIMUM" "TEMPERATURE MAXIMUM" 3 * * Can be used as a shortcut. Auto mode Steps User says System answer 1 "CLIMATE" "CLIMATE" 2 "AUTO MODE" * "AUTO MODE" * Can be used as a shortcut.
Connectivity The system supports a range of external devices, to fully integrate with your audio unit via the USB and auxiliary input sockets. Once connected, control of the external device is possible via the audio unit. GENERAL INFORMATION CAUTIONS Take care when handling external devices with exposed electrical connectors (such as the USB plug). Always replace the protective cap/shield when possible. There may be a risk of electrostatic discharge causing damage to the device.
Connectivity Connection To enable voice control for custom playlists and folders, follow the procedure below: • Create folders named with the structure "Ford<*>" where <*> is a number 1-10. For example "Ford3" without an extension. • Create playlists named with the structure "Ford<*>.m3u" where <*> is a number 1-10. For example "Ford5.m3u" without any space between "Ford" and the number. Plug in the device, and if necessary secure it to prevent movement within the vehicle.
Connectivity Bonding the device Information not available Note: Some audio and navigation units have a separate Bluetooth audio menu. Use this to access setup and control. E100028 Sony radio To connect the device to the system follow the same procedure as for Bluetooth hands free phones. See Bluetooth setup (page 176). Operation Select the USB device as the audio source by repeatedly pressing the CD/AUX button until USB appears in the display.
Connectivity Note: If you wish to jump to the top level of the USB device contents, press and hold the left arrow key. To browse the device contents, press the SELECT button once. The display will show the track information, together with other important information described below: • A vertical scroll bar on the right side of the display shows the current position of the folder view.
Connectivity Press the SCAN button to scan the current playlist if it is in operation, or the complete USB device or folder. • Press the INFO button to display the following: • filename • title • artist • album • track number and playing time. • "<" to the left hand side of the display indicates that a further level up is readable. Icons to the left of track/folder text indicate the type of file/folder. Refer to the list for an explanation of these icons.
Connectivity iPod is the active source The display will show the track information, together with other important information described below: • A vertical scroll bar on the right side of the display shows the current position of the list view. • ">" after an entry indicates a further level down is readable (for example all albums by a particular artist). • "<" before the list indicates that a further level up is readable.
Connectivity Press the INFO button to display the following: • title • artist • track number and playing time. To navigate the iPod contents, use the rotary scroll/select button to browse through lists. Push the button to expand the contents within the highlighted playlist, album, artist, genre or to commence playback of a particular track. Press ESC to go up one level. Repeated button presses will scroll through these displays.
Connectivity The iPod menu list for browsing contents will be available through the display. Navigation of the contents follows the same principles as for iPod standalone use (for example search by artist, title, etc.). To browse the iPod contents, press the scroll up or down arrow button. Press the SCAN button to scan the currently selected tracks. Press the INFO button to display the following: • title • artist • track number and playing time.
Navigation introduction ROAD SAFETY WARNINGS The system provides you with information designed to help you reach your destination quickly and safely. For reasons of safety, the driver should only program the system when the vehicle is stationary. The system provides no assistance with respect to stop signs, traffic lights, areas under construction or other important safety information. Do not use the system until you have familiarised yourself with its operation.
Navigation system Installing the micro SD card GETTING STARTED CAUTION Using the system with the engine off will drain the battery. 1 Note: You will be charged when sending and receiving text messages. Note: Refer to your phone handbook for all phone functions and operation. 2 Note: Keep the activation code (printed on the installation guide) in a safe place. Note: Retain the activation text message in your mobile phone inbox. E114212 Compatibility of phones 1.
Navigation system E114213 2. Switch your mobile phone on and start the "Ford Mobile Navigation". 3. Choose "Select Destination". 4. Choose "Enter Address". 5. Change route options if necessary and start the route guidance. 6. The vehicle display will show the turn information. Voice instructions are heard via the vehicle speakers. Note: Your mobile phone will display your current position. 7. You are able to exit the application and continue your route guidance after restarting the application.
Appendices www.novero.com/declaration_of_conformity TYPE APPROVALS The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Ford Motor Company is under license. Other trademarks and trade names are those of their respective owners. FCC/INDUSTRY CANADA NOTICE This device complies with Part 15 of the FCC Rules.
Appendices E114220 WARNINGS ELECTROMAGNETIC COMPATIBILITY Radio frequency (RF) transmitter equipment (e.g. cellular telephones, amateur radio transmitters etc.) may only be fitted to your vehicle if they comply with the parameters shown in the table below. There are no special provisions or conditions for installations or use. WARNINGS Your vehicle has been tested and certified to European legislations relating to electromagnetic compatibility (2004/104/EC).
Appendices WARNINGS Keep antenna and power cables at least 100mm from any electronic WARNINGS modules and airbags. 6 4 1 2 3 8 5 7 E85998 Frequency Band MHz Maximum output power Watt (Peak RMS) Antenna Positions 1 – 30 50 W 3, 8 30 – 54 50 W 2, 3 68 – 87.
Appendices Note: After the installation of RF transmitters, check for disturbances from and to all electrical equipment in the vehicle, both in the standby and transmit modes. Check all electrical equipment: • with the ignition ON • with the engine running • during a road test at various speeds. Check that electromagnetic fields generated inside the vehicle cabin by the transmitter installed do not exceed human exposure limits specified in EU directive 2004/40/EC.
Index A Auto-dimming mirror..............................62 Autolamps................................................47 Automatic climate control.....................83 A/C Air distribution...............................................85 Blower............................................................84 Mono mode..................................................84 Recirculated air.............................................85 Setting the temperature.............................
Index Booster cables Booster cushions.....................................19 Checking the wiper blades...................43 Child safety...............................................16 Child safety locks.....................................21 Booster cushion (Group 3)..........................19 Booster seat (Group 2)................................19 Left-hand side...............................................21 Right-hand side.............................................
Index D Engine coolant check...........................148 Checking the coolant level........................148 Topping up...................................................148 Detachable tow ball...............................127 Engine immobiliser..................................36 Driving with a trailer....................................129 Inserting the tow ball arm..........................128 Maintenance...............................................129 Removing the tow ball arm...............
Index G Information messages...........................73 All wheel drive...............................................74 Doors open....................................................75 Keyless system.............................................75 Lighting...........................................................76 Maintenance.................................................76 Message indicator........................................74 Message symbols........................................
Index L Manual seats............................................91 Lighting control........................................46 Manual transmission.............................108 Message centre All vehicles......................................................91 Headlamp flasher.........................................46 Home safe lighting.......................................46 Lighting control positions............................46 Main and dipped beam...............................
Index Personalised settings..............................71 Remote control battery Chime deactivation......................................73 Clock setting..................................................71 ESP..................................................................71 Help screen and navigation information................................................72 Language setting.........................................72 Navigation information.................................72 Steering...............
Index Switching off the engine.......................103 Tyre repair kit...........................................161 Vehicles with a turbocharger....................103 Checking the tyre pressure......................164 General information....................................161 Inflating the tyre...........................................162 Using the tyre repair kit...............................161 Symbols glossary......................................5 Symbols in this handbook.....................
Index W Using the telephone - Vehicles With: Navigation System..............................180 Changing the active phone.......................181 Debonding a bonded phone.....................181 Making a call................................................180 Muting the microphone.............................180 Receiving an incoming call........................180 Receiving a second incoming call............180 Warning lamps and indicators..............64 ABS warning lamp..............................
Feel the difference AV4J-19A321-DA (CG3542en)
