SAFETY DATA SHEET 30066 Section 1. Identification Product name Product code Other means of identification : FORMBY'S® Tung Oil Finish High Gloss : 30066 : Not available. Product type : Liquid. Relevant identified uses of the substance or mixture and uses advised against Not applicable.
Section 2. Hazards identification Prevention Response Storage Disposal Supplemental label elements Hazards not otherwise classified : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use explosionproof electrical, ventilating, lighting and all material-handling equipment. Use only nonsparking tools. Take precautionary measures against static discharge. Keep container tightly closed.
Section 4. First aid measures Inhalation Skin contact Ingestion : Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Section 4. First aid measures Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. See toxicological information (Section 11) Section 5.
Section 6. Accidental release measures Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g.
Section 8. Exposure controls/personal protection Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.
Section 9. Physical and chemical properties Vapor density Relative density : 5 [Air = 1] : 0.85 Solubility : Not available. Partition coefficient: noctanol/water : Not available. Auto-ignition temperature : Not available. Decomposition temperature : Not available. Viscosity : Kinematic (room temperature): <0.07 cm2/s (<7 cSt) Kinematic (40°C (104°F)): <0.07 cm2/s (<7 cSt) Aerosol product Heat of combustion : 0.00002885 kJ/g Section 10.
Section 11. Toxicological information Teratogenicity Not available. Specific target organ toxicity (single exposure) Name Category Route of exposure Target organs Med. Aliphatic Hydrocarbon Solvent Category 3 Not applicable. Respiratory tract irritation and Narcotic effects Name Category Route of exposure Target organs Med. Aliphatic Hydrocarbon Solvent Category 2 Not determined Not determined Specific target organ toxicity (repeated exposure) Aspiration hazard Name Result Med.
Potential immediate effects : Not available. Potential delayed effects : Not available. Potential chronic health effects Not available. General Carcinogenicity : May cause damage to organs through prolonged or repeated exposure. Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels. : No known significant effects or critical hazards. Mutagenicity : No known significant effects or critical hazards.
Section 13. Disposal considerations inside the container. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Section 14. Transport information DOT Classification TDG Classification Mexico Classification IATA UN1263 IMDG UN number Not regulated. Not regulated.
Section 16. Other information Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks Although HMIS® ratings are not required on SDSs under 29 CFR 1910. 1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may be purchased exclusively from J. J.