WASCHVOLLAUTOMAT WASHING MACHINE ML 1300 146 4600 02 - 12/03 Gebrauchsanweisung Instructions manual
CONTENTS FOR THE INSTALLER .................................. 28 Warnings ...................................................... 28 Technical characteristics ........................... 28 Installation ................................................... 29 Unpacking ................................................ 29 Position .................................................... 29 Moving your washing machine ................. 29 Leveling .................................................... 29 Water inlet .
A. FOR THE USER 1. WARNINGS Keep this user’s manual with your washing machine. If you sell your washing machine or give it away, make sure that it is accompanied by its user’s manual. The new user can then be informed of how the washing machine operates and read relevant warnings. These warnings have been written for your safety and for the safety of others. Please read these comments carefully before installing and using your washing machine. Thank you for your attention. 1.1.
2. WASHING MACHINE DESCRIPTION 1 2 1 - Control panel 2 - Lid opening handle 3 - Leveling screws 4 - Filter door 5 - Lever for moving the washing machine 5 4 3 2.1. The detergents dispenser Symbols 3 - softener (do not exceed the MAX mark) 2 - wash 4 - softener and Javel water overflow (if overfilled). 3 2 1 1 - prewash 4 2.2.
3. HOW TO DO A WASH? 3.4. Choice of the temperature and spin drying speed Before the first wash in your washing machine, we recommend that you should do a preliminary wash at 90°C with detergent but without any washing to clean the tub. The recommended temperature is displayed when you make the selection. You can modulate the temperature using the temperature pushbutton.
3.5.5. "Delayed start" option "rinse hold"* option, "0" flashes in the display window. Before you can open the lid, the water has to be drained : turn the programme selector on "AUS", choose the draining programme (ABPUMPEN) or the spinning programme (SCHLEUDERN), press then the "START/ PAUSE" pushbutton. This option delays start of the program to 23 hours. Select the number of hours after which you want the program to begin by pressing on the pushbutton several times.
4. PROGRAMS TABLE The following does not show all possibilities, but simply the most frequent settings. Load Possible options Temperatures Approximate consumptions °C liters kWh 5 kg Prewash Quick wash Rinse hold BIO 90 60 (*) 59 42 2,00 0,95 COLORS Colors, for example normally dirty work clothes. 4,5 kg Prewash Quick wash Rinse hold BIO 40 55 0,70 SYNTHETICS Synthetic fabrics, underwear, color fabrics, noniron shirts, blouses.
5. WASHING GUIDE 5.3. Detergents and additives Only use detergents and additives suitable for use in a washing machine. Read the manufacturer's instructions and respect sections 2.1 and 3.2. 5.1.
5.4.
6. CARE AND CLEANING 6.4. The drain filter Do not do any cleaning operation until you have unplugged the washing machine. Clean the filter at the bottom of the washing machine regularly. The "filter"* light comes on if the filter is blo-cked. In this case clean it immediately. If you wash washing that is very fluffy, clean it after each wash. 6.1. Descaling the washing machine Normally there is no need to descale the washing machine if the detergent was correctly proportioned.
7. OPERATING PROBLEMS Many checks have been carried out during the manufacture of your washing machine. However, if you face a problem with its operation, please read the following sections before calling the After Sales service.
Symptom Cause The «DRUM POSITIONNING» light is not on at the end of the cycle: • the drum could not reach the right position due to a persistent unbalanced mass; turn the drum manually. Error code E40* is displayed in the display window and the led END** flashes 4 times***: • the cover is not correctly closed.
B. FOR THE INSTALLER 1. WARNINGS • • • • • This washing machine is heavy. Take care when moving it. You must remove the packing on the washing machine before use. Failure to remove all transport protection devices can cause damage to the washing machine or nearby furniture. The washing machine must be unplugged while packing is being removed. Do not allow any one other than a qualified plumber to make the hydraulic connections necessary to install your washing machine.
3. INSTALLATION If you want to keep your washing machine aligned with the adjacent furniture, you can cut the pipe support strip at the back of your washing machine. Leave the two side closers in place. 3.1. Unpacking Packing used to protect internal parts of the washing machine during transport must be removed before the washing machine is put into service for the first time. 3.2. Position Remove all packing from the washing machine.
Installation: 1. Screw the supply hose connector onto the threaded end of the water inlet tap (20 x 27 mm). 2. The other end of the water inlet hose, located on the side of the appliance, can be orientated in any direction. Undo the tightening ring slightly, rotate the end of the pipe and then do up the ring securely. 3.6. Drain The drain siphon must be placed inside a drain pipe (or in a washbasin) at a height of between 70 and 100 cm. Make sure that it cannot fall.