Installation Manual 24 Inch Stainless Steel Dishwasher F24DWS250SS
CONTENT CONTENT IMPORTANT SAFETY INSTRUCTIONS...................................................................................... 2 INSTALLATION PREPARATION .................................................................................................5 PREPARE DISHWASHER................................................................................................... 5 PREPARE AND ROUTE THE ELECTRICAL SUPPLY...................................................................
IMPORTANT SAFETY INSTRUCTIONS Please read these instructions completely and carefully. IMPORTANT— Observeallgoverningcodesandordinances. Note to Installer - Be sure to leave these instructions for the consumer's and local inspector'suse. Note to Consumer-Keep these instructions with your Owner’s Manual for future reference. Skill Level -Installation of this dishwasher requires basic mechanical and electrical skills. Proper installation is the responsibility of the installer.
INSTALLATION REQUIREMENTS TOOLS AND PARTS Materials for New Installations Only: INSTALLATION REQUIREMENTS Gather the required tools and parts before starting installation. PARTS SUPPLIED Waste tee for house plumbing, if applicable Hand shut-off valve Coupler for extending drain line, if applicable -V\Y 7OPSSPWZ юH[ OLHK ^VVK ZJYL^Z SVUN [V ZLJ\YL dishwasher to underside of countertop (in literature package).
IINSTALLATION REQUIREMENTS For New Installations Only: Tubing Cutter INSTALLATION REQUIREMENTS Tubing cutter Drill and appropriate bits Hole saw set Drill and Bits Hole Saw Set 4
INSTALLATION PREPARATION DRAIN PREPARATION Do local codes or ordinances require an air gap? Will waste tee or disposer connection be less than 18" above the юVVY& >PSS PUZ[HSSH[PVU OH]L H KYHPU SVVW SLZZ [OHU HIV]L юVVY& If the answer to ANY of the 3 questions above is YES, Method 1 MUST be used. Otherwise either Method 1 or Method 2 may be used. Figure C or Figure D.
INSTALLATION PREPARATION INSTALLATION PREPARATION PREPARE AND ROUTE THE ELECTRICAL SUPPLY NOTE: A grounded 3 prong outlet is required inside a cabinet next to the dishwasher cabinet opening. You Must Have: 120-voit, 60Hz, AC-only,12-amp, fused electrical supply. We Recommend: A time-delay fuse or circuit breaker. A separate circuit. Connecting Dishwasher with A Power Cord: Power cord must plug into a grounded 3 prong outlet, located in the cabinet next to the dishwasher opening.
INSTALLATION PREPARATION PREPARE HOT WATER LINE AND POWER ;OL SPUL TH` LU[LY MYVT LP[OLY ZPKL YLHY VY юVVY ^P[OPU [OL ZOHKLK area shown in Figure F. ,HJO J\[ HU HKKP[PVUHS KPH OVSL [V HJJVTTVKH[L the water line and the power cord. +PH Shut-off Hole Valve Hot +PH Hole Turn off the water supply. Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly recommended and may be required by local codes.
INSTALLATION PREPARE HOT WATER LINE AND Water Line Connection POWER CORD HOLE INSTALLATION ;OL SPUL TH` LU[LY MYVT LP[OLY ZPKL YLHY VY юVVY ^P[OPU [OL ZOHKLK area shown in Figure F. ,HJO J\[ HU HKKP[PVUHS KPH OVSL [V HJJVTTVKH[L the water line and the power cord. +PH Shut-off Hole Valve Hot CAUTION: A Cabinet Face Figure F 9 +PH Hole Turn off the water supply. Install a hand shut-off valve in an accessible location, such as under the sink.
INSTALLATION STEP 2 - CHECK DOOR BALANCE BEFORE YOU BEGIN + INSTALLATION STEP 1 - HANDLEBAR ASSEMBLY - Use a hex wrench to install the outside door handle, ※This step is only applicable to the W60C4A411B model. Haxtun tools CR-V 4mm 30°~90° balance 3~7KG Figure H Hexagon wrench-M6 Figure G After placed the panel on the dishwasher, please try open and close the door to test the balance to check out whether the door can remain a same place.
INSTALLATION STEP 3 - INSERT DRAIN HOSE AND POWER CORD THROUGH CABINET STEP 4 - SLIDE DISHWASHER PARTIALLY INTO CABINET INSTALLATION DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. Slide dishwasher into the opening a few inches at a time. Maximum Drain Hose Length 10' Water Line Drain Hose Power Cord Figure I Insert drain hose into cabinet wall hole. Insert the power cord into another cabinet wall hole. TIP! 7VZP[PVU ^H[LY SPUL HUK OV\ZL ^PYPUN VU [OL юVVY [V H]VPK interference with ba
INSTALLATION STEP 5 - POSITION DISHWASHER UNDER COUNTERTOP STEP 6 - LEVEL DISHWASHER IMPORTANT: Reposition Dishwasher by .YHZWPUN )V[O :PKLZ ^P[O Hands Dishwasher must be level for proper dish rack operation and wash performance. Place level on door and rack track inside the tub as shown to check that the dishwasher is level. Check Level -YVU[ [V )HJR Check Level Side to Side Do Not Push Against Front Door Panel with Knee. Damage to The Door Panel Will Occur.
INSTALLATION Adjust the height by turning the feet to make sure the dishwasher is level. STEP 7 - FIXATION OF DISHWASHER 1. Fixing the dishwasher with the cabinet by turning the screws. 2. Plug the four hole plugs into the holes in the sketch map. INSTALLATION ST4*26 hole plug Adjust the back feet Adjust the front feet Figure J TIP: Pull lower rack out, about halfway. Check to be sure the rack does not roll forward or back into dishwasher.
INSTALLATION Water Line Connection STEP 8 - CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. INSTALLATION ;OL KYHPU OVZL TVSKLK LUK ^PSS э[ ϦVY KPHTL[LY JVUULJtions on the air gap, waste tee or disposer. Cut on the marked line as required for your installation. Connect drain line to air gap, waste tee or disposer using either previously determined method.
INSTALLATION IMPORTANT: STEP 9 - CONNECT POWER SUPPLY When connecting drain line to disposer, check to be sure that drain plug has been removed. Power supply cord-Plug into a grounded 3 prong outlet. INSTALLATION DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE. Remove Disposer Plug TIP: Avoid unnecessary service call charges. Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer. Figure O Plug into a grounded 3 prong outlet.
WARRANTY REGISTRATION INSTALLATION STEP 10 - PRE-TEST CHECKLIST Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions JHU YLZ\S[ PU KLH[O эYL VY LSLJ[YPJHS ZOVJR Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. *OLJR [V IL Z\YL WV^LY PZ 6-- 6WLU KVVY HUK YLTV]L HSS MVHT HUK WHWLY WHJRHNPUN 3VJH[L [OL 6^U
INSTALLATION STEP 11 - DISHWASHER WET TEST INSTALLATION Plug power cord into outlet. Power on and select Rinse Wash program. Close door and press the start buttons. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on. Check for leaks under the dishwasher. If a leak is found, turn power supply off, then tighten connections. Restore power after leak is corrected. Check for leaks around the door.
