DISHWASHER Installation Manual Built-In Dishwasher F24DWS450PR
INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS Throughout this manual, you'll see Warning and Caution notes. These warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It's your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Midea is not liable for damages resulting from improper use.
Prior to removal of original dishwasher and the installation of your new unit, make sure to switch off your circuit breaker. Do not connect the dishwasher until you have completed the installation. Connecting the power cable is the last step when installing the dishwasher. All wiring and grounding must be done in accordance with the electrical code applicable to the region.
Before Installing The Dishwasher Tip-Over Hazard Do not use the dishwasher until it is correctly installed. Do not push down on the door when it is open. Do not place excessive weight on the open door. Electric Shock Hazard Failure to follow these instructions can result in death, fire, or electric shock: Electrically ground the dishwasher Connect the ground wire to the green ground connector in the junction box. Do not use an extension cord.
CONTENTS 01 02 6 PREPARING THE DISHWASHER ENCLOSURE 6 Product dimensions 6 Enclosure dimensions 7 INSTALLING THE DISHWASHER 7 STEP 1 10 STEP 2 Select the best location for the dishwasher 11 STEP 3 Check water supply requirements and cautions 12 STEP 4 Check the electrical requirements and cautions 13 STEP 5 Unpacking and inspecting the dishwasher 15 STEP 6 Preparing the dishwasher 16 STEP 7 Placing the dishwasher and connecting the hot water supply line 17 18 19 22 23 03 Check
PREPARING THE DISHWASHER ENCLOSURE Product Dimensions Rear view Front view Back view 825mm 600mm 580mm The water supply line, power cable and drain hose should go through this space behind the dishwasher. Then, the power cable run in channels under the dishwasher to connections in the Front. Enclosure Dimensions 23.6"(600mm) minimum The installation enclosure must be clean and free of any obstructions. 23"(580mm) minimum The enclosure must be at least 23.6 inches wide 23 inches deep and 32.
INSTALLING THE DISHWASHER Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you're not at risk of injury when washing dishes. Step 1 Check The Parts And Tools Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process. Parts Required Provided with the dishwasher. Check when you unbox the dishwasher in Step 5.
Twist on wire connector Strain relief Electrical tape & Standard duct tape Hot water supply line 90° Elbow Tube fittings Air gap Rubber connector Hose clamp Power cable Teflon tape or sealing compound Decoration door For the hot water supply line ? We strongly recommend using copper tubing with a compression fitting or a flexible stainless steel braided hot water supply line. Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube fitting.
Tools required Electric drill Safety glasses Gloves Wire stripper Pliers Pencil Phillips screwdriver Cutting knife Hole saw Torx t20 Hex L-wrench Flashlight Nipper Flat screwdriver Adjustable wrench Tape measure Tubing cutter 9 Level
INSTALLING THE DISHWASHER New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Repace the existing connections as necessary.
STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS The hot water supply line pressure must be between 0.04-1MPa. Adjust the water heater to deliver water between 120 ° F(49° C) ~149 ° F(65° C). The dishwasher must be connected to a hot water supply between 120 °F(49°C)~149 °F(65°C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 °F(65°C) to prevent damage to dishes.
INSTALLING THE DISHWASHER Step 4 Check The Electrical Requirements And Cautions The electrical requirements for the dishwasher are as follows: In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes. For cable direct connections.
Step 5 Unpacking And Inspecting The Dishwasher unbox the dishwasher in an open area free of obstruction both around the carton and overhead. We recommend that you retain the carton and all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product's components from the carton prior to disposal. Unboxing 1. Unbuckle or cut the four straps securing the carton top. 2.
INSTALLING THE DISHWASHER Plumbing 1. Check the hot water connection on the front left-side of the base of the dishwasher. The mountingplate should be secured to the front of the base, the threads inside the connection should be smooth and shiny, and the area should be clean and free of any debris. 2. Check the plastic Brake and Sensor cases to ensure these assemblies are not cracked and that all nconnections are secure. 3.
Step 6 Preparing The Dishwasher 1. Ensure that the circuit breaker and water supply valve are turned off before proceeding with the following steps. Before you move or lay down the dishwasher for installation, make sure to adjust the height of the legs so the legs are as short as possible. This prevents the legs from breaking. Level the dishwasher by adjusting the height of the legs after you have the dishwasher in place. 2.
INSTALLING THE DISHWASHER Step 7 placing The Dishwasher And Connecting The Hot Water Supply Line 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See Step 8, Leveling the Dishwasher.) 2. Locate the hot water supply line and the power cable. 3. Place the dishwasher so that the power cable is in the right channel of the base of the dishwasher.
Step 8 Leveling The Dishwasher 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level.If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level.See the first note below for instructions on adusting the height of the front legs. 2. Use the level to check if the dishwasher is level front to back, as shown in the figure to the right.
INSTALLING THE DISHWASHER Step 9 Securing The Dishwasher You must fix the dishwasher to the countertop or cabinet side walls for additional stability and safety. 1. If the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below. If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow the Instructions in 2-2 below. 2-1.
1 2 3 1 2 3 1 2 3 4 Adjustment cap Screw to side wall Step 10 Connecting The Drain Hose 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. You must connect the drain hose in accordance with the water pipe installation regulations in your region. Case 1.
INSTALLING THE DISHWASHER Case 2. With disposal With disposal Disposal with an air gap Drain hose2 3. Check the size of the sink's drain hose connector(21mm- as shown in Figure 11 below). If the end of the drain hose does not fit onto the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store. 4. Slide a hose clamp over the end of the drain hose.
The drain hose internal diameter is 21mm Secure the drain hose to the sink wall using cable ties or other fastening materials. Otherwise, the drain hose may bend at the end. causing a drainage problem or excessive supply of water.
INSTALLING THE DISHWASHER Step 11 Wiring Connections 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line. 3. Pass the power cable through the strain relief, and then into the junction box (Figure 14). 4.
Step 12 Completing The Installation 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4. Turn on the dishwasher, and then select and run a cycle. Check if the power turns on correctly and if there is any water leakage while the dishwasher is operating.
Step 12 Completing The Installation 7. Tension adjustment of the door spring. The door springs are set at the factory to the proper tension for the outer door. If the decoration door is installed, you will have to adjust the door spring tension. Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable, see figure 20. Door spring tension is correct when the door remains horizontal in the fully opened position, yet rises to a close with the slight lift of a finger.
SPECIFICATIONS Power supply 120 V 60 Hz Water pressure 0.04 - 1 MPa Dimensions (Width x Depth xHeight) 23.62" x 22.83" x 32.48" Nominal inlet water temperature 120 ° F(49° C) Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual.
