FS-40 Alarm / Remote Start Combo System INSTALLATION HANDBOOK: INTRODUCTION Congratulations on your choice of a Crimestopper combination alarm & remote engine starter with Data Port Technology. This installation book is designed for the installer or individual with an existing understanding of automotive electrical systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you READ THIS MANUAL before beginning your installation.
TABLE OF CONTENTS Cautions & Warnings…….…………………………..…..………………………………………………………………………3 Component Mounting………….……………………..……………………………………………….…………………..……..3 Wiring Information ………….…………………………....……………...……………………………………………..……4-11 Power Door Lock Wiring……………………….....….………………...….………..…….……..…………...……………12-14 Tachless, Tach Reference, Tach Finder, Timed Crank Modes………..……………………………………………....15-17 Diesel Glow Plug Delay………………………………………………………………………………………………...………18 Programmable Options, Options Reset……….
CAUTIONS & WARNINGS DAMAGE RESULTING FROM IMPROPER INSTALLATION IS NOT COVERED UNDER WARRANTY!! DO NOT remote start your vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes. DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with the brake/gas pedals, steering column, or any other moving parts in the vehicle.
WIRING: 9-PIN Connector (22 gauge wires) Green: MODE A: (-) Start Activation Input This wire allows an outside source or accessory to activate a Remote Start. A 1-second Ground pulse on this wire will trigger a remote start. This wire can be used with an RS-400 temperature module.
WIRING: 9-PIN Connector Cont. Green/Red: (-) 500mA Remote Aux. Output 1 (Programmable Option #10, requires relay) This is a programmable output that can operate two different ways: 1 - (DEFAULT) Disarm with Remote Auxiliary Output that provides a ½ second (-) Negative pulse when Button #3 is pressed to open a Factory power trunk or hatch release.
WIRING: 9-PIN Connector Cont. Blue/White: (-) Passenger Door Unlock Output (Optional, requires relay) This wire activates when the unlock button on the remote is pressed a second time within 15 seconds upon disarming. This wire is used for the Optional Separate Driver’s/Passenger Unlock feature. Connects to unlock circuit for passenger door or doors. See DOOR LOCK WIRING for special configuration options (page 14).
WIRING: 9-PIN Connector Cont. Orange/Black: (-) OEM Disarm Output This wire provides a Ground pulse to disarm the vehicles Factory Anti-Theft System prior to a Remote Start. Connect this wire to the vehicles' anti-theft disarm wire. This wire is sometimes found coming off the Driver's door key switch or at the Factory Anti-theft control module.
WIRING: 5-PIN Connector (22 gauge wires) Violet: (+) Door Pin Switch Input Same as the GREEN wire below except this wire is used for vehicles that show a positive voltage (+12 volts) when the door is open and a ground when doors are closed as in many Ford, Lincoln, and Mercury vehicles. Green: (-) Door Pin Switch Input Identify the wire that reads ground when any door is open and 12 volts when all doors are closed. Some vehicles may have isolated door triggers.
WIRING: 5-PIN Connector Cont. OPTIONAL CAR JACK WIRING: HIDDEN BUTTON or TOGGLE SWITCH (Not Included) PINK IGN SW + IGN + 12 V PINK FULL-TIME CARJACK CONTROLLED W/SWITCH White: (+12V) Brake Reset Connect the White wire to the side of brake pedal switch that shows +12 volts ONLY when pedal is depressed. This will turn off the remote start if someone attempts to drive the car without the keys or if the Ignition key is not turned on all the way.
WIRING: 4-PIN Shock Sensor (26 Gauge wires) Sensor Adjustment Adjust the main shock sensor with the small White dial. Clockwise will increase sensitivity and counter-clockwise will decrease sensitivity. Adjust Pre-Warning level with small Black dial. RED LED (Trigger) GREEN LED (Pre-Warn) + Adjustments (-) TRIGGER (-) PRE-WARN + WHITE BLUE GROUND BLACK 12 VOLTS RED SHOCK SENSOR: The sensor supplied with this system does not require any additional wiring.
WIRE: 4 PIN OUTPUT CONNECTOR (22 gauge wires) YELLOW/BLACK: (-) OEM REARM OUTPUT This wire provides a ground pulse to rearm the vehicles' FACTORY anti-theft system after a timed-out or aborted remote start. Connect this wire to the vehicles' anti-theft rearm wire or to the door pin circuit depending on your requirements. This wire may be needed to pulse the door pin circuit on vehicles with retained accessory power.
POWER DOOR LOCKS: (22 gauge wires) PIN 1: BLUE: (-) Negative pulse for UNLOCK PIN 2: RED: 12V When using external relays (TERM 86) PIN 3: GREEN: (-) Negative pulse for LOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for Positive Door Lock systems. CS-610S1: Aftermarket door lock actuator (motor).
DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING GREEN GREEN RED BLUE RED FUSED +12V + BLUE 85 86 87 87A 30 FACTORY POWER LOCKING RELAYS L UL 87 87A 30 FACTORY POWER LOCKING UL RELAYS AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN GREEN FUSED +12V + RED BLUE 85 86 87 87A 30 85 85 86 86 87 87A 30 87 87A 30 CUT L FUSED +12V + RED BLUE MASTER SWITCH UL 86 L REVERSE POLARITY DOOR LOCK WIRING + 85 CUT 13 85 86 87 87A 30
SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGATIVE TRIGGER DOOR LOCKS BLUE/WHITE GREEN RED BLUE DRIVER'S DOOR MOTOR 85 86 L 87 30 87A L UL + UL FACTORY LOCK RELAYS +12V FUSED CUT UNLOCK WIRE WIRING FOR REVERSE POLARITY DOOR LOCKS BLUE/WHITE GREEN RED FUSED +12V + BLUE MASTER SWITCH 85 85 86 86 87 87A 30 87 30 87A + L 86 87 87A 30 CUT UL CUT 85 CUT LOCK WIRE UNLOCK WIRE 14
TACHLESS MODE Your system includes a Tach-less mode that actively monitors and compares the vehicle’s resting voltage versus its running voltage each time a remote start is performed; [instead of the conventional tach-pulse method]. Smart Tachless mode adjusts automatically to maintain optimum efficiency over the life of the installation. IMPORTANT NOTES: (1) SETUP may be required for the Tachless Mode.
TACH MODE & TACH FINDER FEATURE Tach Reference Mode provides reliable remote starting performance though engine speed sensing. When using Tach Reference Mode, the WHITE/RED wire is used for Tach signal [Engine RPM] input. Most modern engines include various points where the Engine Speed [Tach] or A/C signal may be obtained. Tach Signal examples: Negative (-) side of ignition coil, at the Distributor or Ignition Control Module, Coil Pack, Engine Computer, or Crankshaft Sensor.
TIMED CRANK MODE As an alternative to Tach or Tachless mode, “Timed Crank” provides an additional method of starting the vehicle without locating an exact tach wire. It uses a timed cranking output combined with the use of the Red/White tach wire as an engine ON/OFF monitor. The Red/White Tach wire MUST STILL be used with this mode.
DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit” input. This may be due to a variety of reasons for example: If your vehicle does not have a viable “Wait to Start Circuit” or you cannot locate and identify the circuit. You can choose from a selection of “pre-cranking” delay times.
OPTION PROGRAMMING TABLE Option # Option Description TX Button #1 TX Button #2 1 Engine Monitoring Learn Tach *Tachless* 2 Auto lock with Ignition OFF *ON* 3 Passive Arming With Ignition or Last Door Ignition and last door ON *OFF* 4 Active Re-Arm ON *OFF* 5 Passive Locks ON *OFF* 6 Parking Lights on w/Disarm OFF *ON* 7 Data Port Protocol OFA Series or SL Series OFA Series *SL Series* 8 Remote Start & Auxiliary Output Button Press Selection Double Button Press *½ Second Pr
OPTION PROGRAMMING TABLE 20 PINK Wire function Passive Carjack *Glow Plug* 21 Starter Cranking Time (Option #16 is set to Timed Crank) 0.75 Sec. *0.5 Sec.* 1.0 Sec. 1.5 Sec.
PROGRAMMABLE OPTIONS Cont. 3. PASSIVE ARMING Passive Arming With Ignition or Last Door: With this option ON, the unit will arm itself 30 Seconds after the ignition is turned off and/or the last door has been closed. Lights will flash twice when last door is closed indicating passive countdown. If a door is reopened, the system will wait and begin countdown again when closed. The LED will flash rapidly during 30 second count down. 4.
PROGRAMMABLE OPTIONS Cont. 12. DOOR LOCK/UNLOCK PULSE TIME: This option controls the amount of time (0.5 sec. or 3 sec.) for the lock/unlock pulse. The standard pulse time for most vehicles is 0.5 Sec. The 3 sec. setting may be required for Mid 1980’s through Mid 1990’s European Vehicles that require a long lock and unlock pulse to operate Vacuum door lock systems. 13. DOUBLE UNLOCK PULSE: With this option ON, the unit will send 2 unlock pulses when the system is disarmed.
PROGRAMMABLE OPTIONS Cont. 21. PRE-SET STARTER CRANKING TIME: (Requires Option #16 in “Pre-Set” Setting) This option controls the starter cranking time when in “Timed Crank” Mode. Choices are 0.5, 0.75, 1.0, or 1.5 sec. 22. DIESEL GLOW PLUG DELAY This option controls the system’s Diesel vehicle interface. Using this option you can control whether the unit monitors the vehicle’s glow plug circuit using the Pink input wire (Default), or you may select a specific delay time Before cranking.
PROGRAMMABLE OPTIONS Cont. 29. Aux #4 Time control: (1 sec. to 255 sec.) Default = 12 seconds This option determines the length of time that is outputted from Aux #4 (Green/White wire). Pressing the Lock or Unlock buttons on the remote raises or lowers the time by one second. 30. Turbo Timer Mode: The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key and exit the vehicle.
PROGRAMMING – TRANSCEIVERS & TRANSMITTERS 1. Turn key to the ON position.( doors will lock if autolock is programmed ) 2. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times. 3. Press button #1 (Lock) of the transmitter.
ALARM TRIGGER DIAGNOSTICS This systems includes disarm diagnostics, through the LED light, that will help in determining what caused the last trigger of the alarm system. This is a valuable tool in determining how the vehicle was tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to correct the problem.
JUMPER PIN DIAGRAM Jumper pins are used to change/configure the operation of the on board multi-function output PINK WHITE wire, the Parking Light WHITE wire and the Glow Plug PINK wire. See the diagrams below for Jumper Pin configurations.
ANTENNA DIAGRAM Antenna should be located at top of widow at least one inch away from metal surface.
HIGH CURRENT PLUG 6 PIN HIGH CURRENT PLUG Diagram not to scale, for illustration purposes only. Your vehicle may differ.
(-) Aux 4 - Green/White Grey Accessory 1 Brown Starter 1 (-) Aux 3 - Violet/White Fuse Control Module (-) Start - Blue/Orange (-) OEM - Yellow/Black ReArm DOOR LOCKS (-) Unlock Blue (+) 12 volts Red (for Relays) (-) Lock Green Data Port Shock Sensor Fuse Red Red 12 Volts Pink Ignition 1 JUMPER SELECT Pink/White JUMPERS *START 2 *IGN 2 *ACC 2 START # 2 ACC # 2 Black TACH Ground Engine Monitor 3 Red/white Not Used 4 5 2 1 6 7 8 0 (-) 500mA or (+)10Amps JUMPERS Park Lights + Glow
DATA PORT This unit includes DP Technology that will allow you to directly Plug-In our Data Port Bypass Modules. There are 2 types of Protocol, OFA series and SL series modules. The default is set for SL series Protocol. Please refer to Databus module manual for detail instructions. The Data Port Protocol must be programmed for the correct module.
www.crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2008Crimestopper Security Products ONLINE TECHNICAL SUPPORT www.crimestopper.