A ) Installation Instructions for Av ant CANT Aluminum Panels with Angle Aluminum RAILING o storms Brackets and Aluminum Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all required building permits. The deck and rallying Installer should determine and Implement appropriate Installation techniques for each Installation situation. Menards® shall not be held liable for In proper or unsafe Installations.
Av ant Aluminum Panel Angle Installation Options Base Cover Aluminum Post —— Aluminum Pressed Fit Aluminum Pressed Fit: Flat Pyramid Cap Flat Pyramid Cap v Angle Aluminum Angle Aluminum: Bracket Bracket Av ant Aluminum Panel Angle Aluminum Angle Aluminum Bracket Bracket Av ant Panel and Aluminum Post Configurations Av ant Panel Only Av ant Installed Panel Required Panel Height Height* Post 12 *Installed alights Include a space between deck surface and bottom edge of bottom tall.
Pr-Drill and Install Angle Aluminum Brackets to Aluminum Posts « Install Post Base Cover by sliding over the top of Aluminum Post. « Mark the centerpiece of each post with a pencil. « Mark hole locations defined in the previous step with a pencil, then per-drill with a 3/16" drill bit, ensuring that the holes are spaced evenly from the center line. » Remove the bolt from the Angle Aluminum Bracket Assembly. = Attach Angle Aluminum Bracket Base piece to the posts with supplied T-25 thread-cutting screws.
Cutting Av ant Aluminum Panels * The best way to cut Av ant Aluminum Panels is to use a miter saw. + Fine tooth carbide tipped blade designed to cut non-ferrous materials is recommended. » Set up a work surface that is level and large sough to support all four comers of the Av ant Aluminum Panel. » Supports should be the same height as saw base to keep Av ant Aluminum Panel straight and level when cutting. * With panels completely supported, make cuts at the marked locations from previous step.
SAVANT Installation Instructions for Av ant Aluminum Adjustable Panels with RAILING u fox mass Stair Aluminum Brackets and Aluminum Posts It Is the responsibility of the Installer to meet all code and safety requirements, and to obtain all required bulling permits. The deck and rallying Installer should determine and Implement appropriate Installation techniques for each Installation salutation. Menards® shall not be held liable for Improper or unsafe Installations.
Important Every stair installation will be different. The rise and run, post position, and post height all need to be carefully lad out before posts are permanently Installed and Av ant Aluminum Adjustable Panels are cut. Mount Aluminum Posts « Wood blocking tied to deck frame must be installed and constructed with treated dimensional lumber with a minimum thickness of « Position the edge of post base plate a minimum of %" from the inside edge of rim joist.
Verify Av ant Aluminum Adjustable Panel Position and Secure with Clamps * Verify the position of the Av ant Aluminum Adjustable Panel. With the help of another person, place the panel into the correct position and secure with clamps to the aluminum posts. * Place a piece of cardboard between the clamping surfaces and the surfaces of the rails and posts o protect the finish. Determine Stair Aluminum Bracket Assembly Location and Mark Rail « Do not Install the Starr Aluminum Bracket Cap at this ime.
Pr-Drill and Install Stair Aluminum Brackets to Aluminum Posts « Remove clamps and Av ant Aluminum Adjustable Panel. * Mark the center line of sate post. The Stair Aluminum Brackets will be installed on the center line. * Remove bolt from the Stair Aluminum Bracket Assembly. * Place the Stair Aluminum Bracket Post piece between the two lines drawn in the previous step and center it on the post. »Use a 3/16" drill bit to per-drill holes.
Install Av ant Aluminum Adjustable Panel + Reposition support blocks. « Position Av ant Aluminum Adjustable Panel so that it aligns with the Stair Aluminum Brackets. Use a clamp to hold the Av ant Aluminum Adjustable Panel in place. « Check the fit of the Av ant Aluminum Adjustable Panel and make any required adjustments. = Pr-drill Av ant Aluminum Adjustable Panel with a 3/16 drill bit, then secure to Stair Aluminum Bracket with a T-25 thread cutting screw.
Installation Instructions for Av ant Aluminum Railing with Straight RAILING w formless Aluminum Brackets and Aluminum Posts SAVANT It Is the responsibility of the Installer to meet all code and safety requirements, and to obtain all required bulling permits. The deck and railing installer should determine and implement appropriate installation techniques for each installation situation. rds® shall not be held liable for Improper or unsafe Installations.
Av ant Panel Installation Options Straight Aluminum Bracket Cap —> [ | Straight Aluminum: Bracket Cup Straight Aluminum Bracket Cap Straight 1[T] %= Bracket Cap Straight Aluminum | __Straight Aluminum| Bracket Cup Straight Aluminum Bracket : Aluminum Bracket Cup > [ Cap Aluminum Post with Post Base Cover and Pressed Fit Pyramid Cap Straight Aluminum |-Support 3 Bracket [ > L— Av ant Panel —J Cup Av ant Panel Installation with Straight Aluminum Bracket » If panel is to be cut to a size other than 6’ and 8' o
Cutting Av ant Panels « The best way to cut Av ant Panels is to use a miter saw. « Fine tooth carbide tipped blade designed to cut non-ferrous materials is recommended. +» Set up a work surface that is level and large enough to support all four comers of the Av ant Panel. «» Supports should be the same height as saw base to keep Av ant Panel straight and level when cutting. = With panel completely supported, make cuts at the marked locations from previous step. * Remove any burrs or shavings from cut edges.
Av ant Panel and Aluminum Post Configurations Av ant Panel Only Av ant Installed Panel Required Panel Height Height* Post *Installed heights Include a space between deck surface and bottom edge of bottom tall. Straight Aluminum Bracket Hole Locations for Av ant Panel Installations Pr-Drilling with a 3/16” drill bit is required.