User Manual Model: FN3108E-B4-1T / FN3108E-B8-2T Version: V1.0.
NVR User Manual Table of Contents Table of Contents...............................................................................................................................................I Security Warning............................................................................................................................................. III Preface..................................................................................................................................................
NVR User Manual 3.4.1 IP Camera Setup.................................................................................................................. 42 3.4.2 Schedule Record.................................................................................................................. 44 3.4.3 Alarm....................................................................................................................................... 45 3.4.4 Device Information............................................
NVR User Manual Security Warning Please change the password of your Foscam NVR App account, and NVR and cameras username regularly. The password should contain a combination of numbers, letters and special characters. Please keep the username and password of your cameras, NVR and Foscam NVR App account safe. Please update your camera to the latest firmware regularly for an optimal user experience. www.foscam.
NVR User Manual Preface Welcome to use our product, Network Video Recorder (NVR) Kit. This document mainly focuses on the installation and configuration of NVR Kit application system. With high performance video, user-friendly GUI, and practical industrial designs. This series NVR Kit is suitable for civil applications such as homes, stores, internet cafes, and small businesses in addition to mainstream security and surveillance applications.
NVR User Manual Important Safety Instructions This chapter describes how to use the product properly so as to prevent danger and property loss. Be sure to follow the security instructions when operating this product. Installation Environment Ensure device is installed in the well-ventilated, dust-free environment. It is recommended to use a voltage stabilizer for supply of power. If the power supply was unmatched, the device might work abnormally or stop working.
NVR User Manual 1 Overview 1.1 Product Introduction The series of product is a NVR Kit. This advanced product series receives a high quality video stream that is transmitted digitally by the IP Camera (IPC). The product can perform live video preview, recording, playback, remote access, and backup simultaneously. 1.2 Key Features Network Monitoring You can access the NVR system remotely through the browser on a PC or access the NVR system locally by using the display or monitor.
NVR User Manual Note When NVR system time and IPC time are different, the NVR recording will based on the NVR system time. Playback You can play recording video files stored in the Hard disk. Recording includes schedule recording, manual recording, and alarm recording. Single-screen playback and four-screen synchronous playback are supported. When display mode is 1080P, it only supports the single-screen playback.
NVR User Manual rights of the three roles vary from low to high. 1.3 Relevant Version Name Recommended Configuration Monitor Network Browser You are recommended to equip a 16:9 monitor with the resolution higher than 1280*720. 10/100M Ethernet or above. This product supports 32-bit IE8 or later versions and does not support 64-bit IE browsers. It also supports Apple Safari. 1.4 Icons Description In the live view mode, there are icons at the right top of the full screen.
NVR User Manual Shutting Down the NVR There are two proper ways to shut down the NVR in the GUI interface. After login, right-click the mouse, you can click Shutdown in the shortcut menu. Choose Menu > System in the Menu interface, then click Shutdown in the System interface. Then turn off the power switch on the rear panel, the power LED indicator on the front panel turns off. Reset You can reset the NVR device to restore the factory settings.
NVR User Manual 2 GUI You can visit the local NVR device via the display or monitor, and view or manage NVR system. NVR device is connected to the network, mouse, and mobile storage devices have been successfully installed. Make sure the video output device is connected successfully. 2.1 Login For the operation, please refer to the Quick Operation Guide. 2.2 Setup Wizard By default, the Setup Wizard starts once the NVR has loaded. The Setup Wizard can walk you through some important settings of the NVR.
NVR User Manual One-Screen / Four-Screen / Nine-Screen Switch between different channels video. Note:The NVR Kit supports eight channels. If you need to display nine channels on the live view window, the sub stream of each IPC must be less than 720P. Menu Click Menu to enter the Menu interface, it includes IPC Manager, playback, Backup, About, Settings and System. For details, please refer to 2.4 Menu.
NVR User Manual [Enable Manual Record] Check the Channel checkbox, Click OK button to take effect. Right-click the mouse to back to the Live view interface. In the live view interface, there are icon at the right bottom of the screen for the channel. [Disable Manual Record] Uncheck the channel checkbox, Click OK button to take effect. Right-click the mouse to back to the Live view window. In the live view mode, The icon disappeared at the right bottom of the screen for the channel.
NVR User Manual [Cruise track] The default cruise tracks have two types: Vertical and Horizontal. Vertical: The IP Camera of the channel will rotate from up to down. Horizontal: The IP Camera of the channel will rotate from left to right. : Start cruise. : Stop cruise. Shutdown Click Shutdown to enter the Shutdown page. You can log out, reboot or shut down the NVR system. 2.4 Menu Right-click in live view mode and select Menu from the Shortcut Menu, the Menu interface is displayed. 2.4.
NVR User Manual Adding Devices in the Menu interface. The Adding Devices interface is displayed. You can search and add the online IP cameras by following the operation. After adding IP cameras, the basic information of the camera lists in the IP Camera List, and you can configure the basic setting of the IP cameras. Note Before adding the IP Camera, make sure that the IP Camera supports FOSCMA or ONIVF protocol. And you have the username, password and port number of the IP camera.
NVR User Manual 1. Select the IPC 2. Input the User Name and Password of the IPC. 3. Click Add button Note: Make sure that the IP address of the IPC and NVR's in the same network segment, and the subnet mask and gateway are the same as the NVR's. 3．And the camera and its information will be added in the IP Camera list. Finally, click the Save button to take effect. www.foscam.
NVR User Manual 4．Right-Click to return the previous interface. 2.4.2 Playback Right-click in live view mode and select Playback from the Shortcut Menu, or choose Menu > Playback in the Menu interface. The Playback interface is displayed. It supports single-screen or four screens. 1: Select a date with recording in calendar. 2: Select the Video Type, and check the checkbox from Channels.You can select up to four channels for playback at the same time.
NVR User Manual been plugged in the NVR. Select some records in the list, then click the Backup button to save the files to the USB Flash Disk. If you want to see the video of this record, double click a record,. Manage the recording Button Description After searching file, click the button to play. Stop Fast backward. The fast backward speed can be 4 times, 8 times, 16 times or 32 times of the normal playing speed. Click this button.
NVR User Manual Fast forward. The fast forward speed can be twice, 4 times, 8 times, 16 times or 32 times of the normal playing speed. Click this button. The multiple of normal playing speed is displayed in the upper right corner of the playback page. For example, ">> X2" indicates the current playing speed is twice of the normal speed. Slow progress. The slow progress speed can be 1/2 times, 1/4 times, 1/8 times, 1/16 times or 1/32 times of the normal playing speed. Click this button.
NVR User Manual [Enable Schedule Recording] 1．Select channel from drop-down box list. 2．Check the Enable checkbox to enable Schedule Recording function. 3．Check the Select checkbox. Note: Check Clear checkbox and If you clear the area. 4．Click and drag the mouse in the relative positions. The selected area is red. 5．Click Save button to take effect for one certain channel. The icon indicate starts schedule recording at the right bottom of the screen for certain channel.
NVR User Manual Firmware Version Choose Menu > About > Firmware Version in the Menu interface. The Firmware Version interface is displayed. You can view the Device Type, Device Name, Firmware Version and Application Version. HDD Info Choose Menu > About > HDD Info in the Menu interface. The HDD Info interface is displayed. You can see, refresh, format backup disk and format record disk. www.foscam.
NVR User Manual Overwrite: When the HDD is full. You can select the whether cover the earliest recording. Select Yes, the NVR will cycle cover the earliest recording; Select No, the NVR will stop recording. Refresh: Click the Refresh button then you can update to the latest information on the hard disk. Format Hard Disk: If the disk is uninitialized, select the record disk, then click Format Hard Disk to format the record disk if the format is incorrect.
NVR User Manual [Searching Log] 1．Select the log type, channel and time. 2．Click the Search button to list all matched logs. [Backup Log] The log information can be exported to USB-flash disk for backup. 1．Double-click the log information by the left mouse in the search result list. The status of the log will change from No to Yes. 2．After the USB-flash disk connect to the NVR by the USB interface. Select the Object from drop-down list. 3．Select the backup select from drop-down list.
NVR User Manual configure the general, video, schedule, network, display, Alarm Settings and OSD. General Choose Menu > Settings > General in the Menu interface. The General interface is displayed. You can configure the basic information of the NVR. Name and Language Parameter Description Device Name You can modify your device name to help you identify it. Language Configure the language of the NVR interface. Setup Wizard Whether to enable setup wizard when the NVR system starts again. www.foscam.
NVR User Manual Click Save button to take effect. Time and Date Parameter Description Time Zone Please select the time zone according to the actual situation. Automatically Whether synchronize your NVR with an Internet time server. synchronize with and Internet time Check: You need to configure the NTP Server. server Uncheck: You need to configure the Date and Time. Date Format You need to configure the date format. Time Format You need to configure the time format.
NVR User Manual Stream Choose Menu > Settings > Stream in the Menu interface. The Stream interface is displayed. You can configure the encoding scheme parameters of the IP Camera, the NVR system will synchronize your IP camera with encoding scheme. www.foscam.
NVR User Manual Parameter Description Channel You can select the channel for the IP Cameras. Stream You can set the value of Resolution, Bit Rate, Frame Rate, Key Frame Interval when the video was set the main stream. The resolution of the IP Camera. Resolution The higher the resolution is,the sharper the video quality is, but also with the increasing stream, which will take up the higher bandwidth. Generally speaking, the larger the bit rate is, the clearer video will become.
NVR User Manual Parameter Description You can select the network type from the drop-down list box. If select the DHCP, NVR system will automatically obtain an IP Type address and other network settings from that server. If select the Static IP, you can configure an IP address and other network settings. HTTP Port The default value is 88. HTTPS Port The default value is 443. You can configure the IP address of the NVR system.
NVR User Manual You can use the UPnP function to enable the fast connection of the device to the WAN via a router without port mapping. MAC Address Note: If you want to enable the UPnP function of the NVR, you must enable the UPnP function of the router to which your NVR is connected. UPNP You can enable or disable the UPNP function. Click Save button to take effect. How to configure the IP Address, Subnet Mask, Gateway, Primary DNS Server, Secondary DNS Server, please refer to 4.
NVR User Manual NVR via internet. Take hostname hk9973.myfoscam.org and HTTP Port. 88 for example, the accessing link of the camera via internet would be http://hk9973.myfoscam.org:88 Third Party DDNS:You can also use third part DDNS, such as www.no-ip.com, www. 3322.com. If you set the third party DDNS, refer to the 4.2 Common operations > 1.Third Party Domain Name Settings. [EMail] Select the EMail page, you can configure the E-mail information of the NVR.
NVR User Manual Parameter Description Enable E-Mail Check the checkbox to enable the Eamil function. Authentication Whether to verify the username and password during login to the mailbox. SMTP Server The SMTP Server IP address or host name. SMTP Port The SMTP port is usually set as 25. Some SMTP servers have their own port, such as 587 or 465. Transport Layer Security usually is None.
NVR User Manual Parameter Description If your FTP server is located on the LAN, you can set FTP address as ftp://IP address/dir.(eg.ftp://192.168.1.103/dir). FTP Address If your FTP server is located on the WAN, you can set FTP address as ftp://domain name/dir.(eg.ftp:test.no-ip.org/dir). FTP Port Default port is 21.You can also change this port manually through FTP server. FTP Mode Here supports two modes: PORT and PASV. FTP Username The user account of FTP server.
NVR User Manual Parameter Description Resolution The output resolution of the NVR. Transparency Configure the transparency of the NVR output interface. Mouse Sensitivity Configure the sensitivity of the mouse. Alarm Settings [Motion Detection] Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the NVR can analyze it and perform many actions to handle it.
NVR User Manual Detection interface is displayed. www.foscam.
NVR User Manual Parameter Description If you select this checkbox, when the Motion detection is triggered, Record the NVR will record automatically and store the record files to the HDD. IPC Audio Warning Buzzer If you select this checkbox, when the Motion detection is triggered,the people around the camera will hear beep alarm sound of the IPC. When the Motion detection is triggered, you can choose whether to enable buzzing sound of the NVR device.
NVR User Manual 1．Click Settings button for the detection schedule. Set up arming schedule of the channel for the motion detection. You can choose a week, one day of a week, the certain time period for the motion detection alarm. 2．Check Select checkbox to select the area. 3．Drag and draw the area for motion detection by left mouse. Note:Check Clear checkbox and If you clear the area, then drag and draw the area for motion detection by mouse. 4．Click the OK button to save and exit the window.
NVR User Manual Check the item, and then click Save button to take effect. OSD Choose Menu > Settings > OSD in the Menu interface. The OSD interface is displayed. You can configure the OSD (On Screen Display) information. Parameter Description Channel Select the channel from the drop-down list. Channel Name It displays the IPC device name of the corresponding channel. Display Channel Name Display Time www.foscam.com Whether to display the IPC device name on the selected channel.
NVR User Manual 2.4.6 System Choose Menu > System in the Menu interface. The System interface is displayed. You can manage the NVR device about User Account, Upgrade, Factory Reset, Para export, Auto Restore, Log Out, Reboot, Shutdown. User Account Choose Menu > System > User Account in the Menu interface. The User account management interface is displayed. User levels by permission from low to high are visitor, operator, administrator. Different user levels have different operating permission.
NVR User Manual After configure the username, password and competence, you need to check Enable checkbox. Then click Save button to take effect. Upgrade Choose Menu > System in the Menu interface, then click upgrade in the System interface. You can check for updates by network or upgrade by local. [Local upgrade] First, a mobile storage device needs to be inserted by the USB interface and the NVR system upgrade file upgrade.bin has been stored in the root directory of the mobile storage device.
NVR User Manual OK button and then the NVR device will reboot automatically. Para export Choose Menu > System in the Menu interface, then click Para export in the System interface. You can import or export a configuration file for NVR system. [Config Export] It is used to save your current settings. It is recommended to backup your configuration before modifying or upgrading firmware. Click Config Export, and then click OK button in the pop-up message box.
NVR User Manual Note: After you have logged out the system, menu operation on the screen is invalid. It is required to input a username and password to unlock the system. Reboot Choose Menu > System in the Menu interface, then click Reboot in the System interface. Click OK button in the pop-up message box, the NVR system will reboot. Shutdown Choose Menu > System in the Menu interface, then click Shutdown in the System interface. Click OK button in the pop-up message box, the NVR system will shut down.
NVR User Manual 3 Web You can access and manage the NVR on a PC through Web browser. 3.1 Instructions before Login Before accessing the NVR Kit by using the Web browser, you need to obtain the following information: The NVR and the PC must be connected to the same LAN and are in the same network segment. You can query or allocate the IP address of the NVR by using the following methods: Through operation on the local GUI, configure an IP address for the NVR.
NVR User Manual Double-click the NVR, and your default browser will open up to the NVR's login page. When Step3 logging in for the first time, you will need to install the add-on. It will pop up the message below the page, as shown in the following figure. Click Install button to install the add-on. Please follow the installation instructions. (Please close the browser during installation.) . Step4 After installing the add-on, refresh the browser and enter the log in interface. www.foscam.
NVR User Manual Input the follow parameter. Parameter Description The username and password of the NVR client. Username / The default administrator username is admin with a blank password, please Password set the new username or password at first using and prevent unauthorized users log in the NVR. Language Step5 Select the language type of the NVR client. Click Login button. When you log in for the first time, it will come to the operating of modify the username and password automatically.
NVR User Manual 3.3 Live Video After login, the live view interface will display. You can configure the play/stop the live view, manual recording, manual capturing, preset, cruise, led, color and so on. 1 2 3 4 Section Icon Name Live Video Description Click this button and back to the realtime preview window. There are Local Settings, Settings, Service 1 Parameter Configuration, User Management, System Configuration Management in the Parameter Configuration interface. Playback Logout www.
NVR User Manual In channels of the NVR, you can add IPC devices. The blue indicates that the channel is previewing state. You can see the video of the connected camera. Channels The gray indicates that the channel is o ine state. There was not the connected camera in this channel. 2 Note: If you need to display nine channels IPC device on the live view window, the sub stream of each IPC must be less than 720P. Play Stop Preset 3 IR LED Play an IPC monitoring video in a channel of the NVR.
NVR User Manual Select the channel, click this button, and you can take a snapshot of the monitoring video page of a Take corresponding channel to the local computer. You Snapshot can set the storage path, refer to the Web > Parameter configuration > Settings > Storage Location. Click this button to manually record the content Record on the monitoring page. The recorded content is stored in the HDD of the NVR.
NVR User Manual Preset settings The default preset position is TopMost, BottomMost, LeftMost, RightMost, you can add other preset positions. Add: Click this icon to save the position you need the IP camera to remember. Delete: Select one preset position and click this button to delete it. GO: Select one preset position in the preset drop-down list and click Go to make the IP camera move the preset position.
NVR User Manual password and port number. Choose (Parameter Configuration) > Adding Device. The IP Camera Setup page is displayed. [Auto Adding IPC] If your camera is the supplied FI9800E, you can check the Automatically search for and add all devices checkbox to automatically add the camera. And make sure you can view all connected cameras which are FI9800E in The Current LAN IPC List box. The NVR system will automatically synchronize its password with the cameras.
NVR User Manual Select the FOSCAM protocol for Foscam brand IPC, and select the ONVIF protocol for other brands IPC. Step3 Click Add button to finish adding. -------End 3.4.2 Schedule Record You can enable or disable schedule recording for the every channel. Set the recording schedule, and then the NVR automatically starts/stops recording according to the configured schedule. The recording files will be save to the HDD or mobile store device.
NVR User Manual 3.4.3 Alarm Motion Detection Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the NVR can analyze it and perform many actions to handle it. Enable motion detection function can trigger certain channels to start recording, or trigger full screen monitoring, output alarm, send Email, upload FTP, buzzer alarm and so on. In the live view mode, there are icons at the right bottom of the screen for each channel.
NVR User Manual Step4 Check the checkbox to select the linkage method. You may refer to follow table for details of linkage methods. Parameter Description When the Motion detection is triggered, you can choose whether to send Send E-Mail e-mail. Note: Make sure you have set Email. When the Motion detection is triggered, you can choose whether to upload detection picture to FTP server. FTP Note: Make sure you have set FTP.
NVR User Manual 2．Drag and draw the area for motion detection by left mouse. Note:To clear the motion detection area, Drag and draw the motion detection area by left mouse. 3．Click OK button to save and quit. When something moving in the detection area, the NVR will alarm. Step6 Set Detection Schedule Set up arming schedule of the channel for the motion detection. You can choose a week, one day of a week, the certain time period for the motion detection alarm.
NVR User Manual For example, click TUE, the all column of TUE turns to red, that means during Tuesday whole day, when something moving in the detection area, the camera will alarm. Click here Choose the Certain Time Period Press the left mouse and drag it on the time boxes, you can select the serial area. Step7 Click Save button to take effect. When the motion has been detected during the detection time in the detection area, the NVR will alarm and adopt the corresponding alarm linkage.
NVR User Manual Step2 Check the alarm type. Step3 Click Save button to take effect. -------End 3.4.4 Device Information Firmware Version You can view the NVR system information, or modify the Device Name. Choose (Parameter Configuration) > Device Information > Firmware Version. The Firmware Version page is displayed. Parameter Description Device Type The product type of NVR. The device name is a unique name that you can give to Device Name your device to help you identify it.
NVR User Manual System Firmware Version Display the system version of your NVR. Application Firmware Version Display the application firmware version of your NVR. Plug-in version Display the plug-in version of your NVR. Click Save button to take effect. Hard Disk Information You can configure the Disk Saturation, Pre-recorded Time for HDD information. Step1 Choose (Parameter Configuration) > Device Information > Hard Disk Information. The Hard Disk Information page is displayed.
NVR User Manual System Log Choose (Parameter Configuration) > Device Information > System Log. The System Log page is displayed. The operation, alarm, exception and information of the NVR can be stored in log files, which can be searched and viewed at any time. The Log Type contains Alarm log, System log and Operation log. [Search Log] 1．Select the Channel, Log Type, Date, Start time and End time. 2．Click the Search button to list all matched logs. 3.4.
NVR User Manual Parameter Description There are two different ways for the date format to synchronize the date and time of the NVR. System Time input the date and time manually. . Click Sync with PC button to synchronize the date and time of the NVR system with your computer. Date Format Select the date format from the drop-down list. Time Format Select the time format from the drop-down list. Step3 Select the Time Zone from the drop-down list.
NVR User Manual Network You can configure the network information of the NVR. Step1 Choose (Parameter Configuration) > Basic Settings > Network.The Network page is displayed. Step1 Configure the network parameter. Parameter Description You can select the network type from the drop-down list box. Network Type If select the DHCP, the NVR system will automatically obtain an IP address and other network settings from that server.
NVR User Manual Parameter Description Server Alternative DNS Server The secondary DNS server of the NVR system. You can use the UPnP function to enable the fast connection of the device to the WAN via a router without port mapping. UPNP Note: If you want to enable the UPnP function of the NVR, you must enable the UPnP function of the router to which your NVR is connected. How to configure the IP Address, Subnet Mask, Gateway, Primary DNS Server, Secondary DNS Server, please refer to 4.
NVR User Manual Step2 Configure the Email parameter. www.foscam.
NVR User Manual Parameter Description Enable E-Mail Enable or Disable the Email function. SMTP Server The SMTP Server IP address or host name. The SMTP port is usually set as 25. Some SMTP servers have their SMTP Port own port, such as 587 or 465. Transport Layer Security usually is None.
NVR User Manual Step2 Configure the FTP parameter. Parameter Description If your FTP server is located on the LAN, you can set FTP address as ftp://IP address.(eg.ftp://192.168.1.103/dir). FTP Address If your FTP server is located on the WAN, you can set FTP address as ftp://domain name/dir.(eg.ftp://test.no-ip.org/dir). FTP Port Default port is 21. If changed, external FTP client program must change the server connection port accordingly. FTP Mode Here supports two modes: PORT and PASV.
NVR User Manual Choose (Parameter Configuration) > Basic Settings > DDNS. The DDNS page is displayed. Note Here take hk9973.myfoscam.org for example. Enable DDNS:Check the DDNS checkbox to enable this feature. Click Save button to take effect. Then you can use http:// Domain name + HTTP Port to access the NVR via internet. Third Party DDNS:You can also use third part DDNS, such as www.no-ip.com, www. 3322.com. If you set the third party DDNS, refer to the 4.2 Common operations > 1.
NVR User Manual Step2 You can configure the follow parameters. Parameter Description Channel You can select one channel from drop-down box list.. You can modify the IP Camera's name. Channel name After you modify the name and save the modification, the NVR system synchronizes the channel name to the corresponding IPC device name. The channel name will be shown on the top left of the video image. Display Channel There are two options: Yes or No.
NVR User Manual You can configure the encoding scheme parameters of the IP Camera, the NVR system will synchronize your IP camera with encoding scheme. Parameter Description Channel You can select the channel for the IP Cameras. Stream You can set the value of Resolution, Bit Rate, Frame Rate, Key Frame Interval when the video was set the main stream. The resolution of the IP Camera.
NVR User Manual Choose (Parameter Configuration) > Basic Settings > Storage Location. The Storage Location page is displayed. Snapshot Pictures To: Click the icon (Take Snapshot) in the Real time Preview page or Playback page, the snapshot picture will be saved to the Snap Picture Path in the local computer. 3.4.6 System Management User Account User levels by permission from low to high are visitor, operator, administrator. Different user levels have different operating permission.
NVR User Manual [Add a User] 1．input the Username and Password. 2．Select the user level from the Competence. 3．Check the Enable checkbox. 4．Click Save button to save the settings and the added new user will be displayed on the list. [Changing Password of Admin] 1．In the Password text field, delete the old password, input the new password. 2．Click Save button to take effect. Import / Export Configurations You can import or export a configuration file for NVR system.
NVR User Manual configuration files, the NVR device will reboot automatically. Note Do not disturb the update process by turning off the power. All current settings will be overwritten when importing a configuration file. If a bad configuration file is uploaded the NVR may not work. Upgrade Choose (Parameter Configuration) > System Management > Upgrade. The Upgrade page is displayed. NVR Upgrade 1. Click Browse to select the upgrade file in the local directory. 2. Click Upgrade to start upgrade.
NVR User Manual 3. Click Upgrade to start upgrade. Don't shut down the power during upgrade. After upgrading, you can see the upgrade result. Patch Installation Choose (Parameter Configuration) > System Management > Patch Installation. The Patch Installation page is displayed. You can install or install patch of the NVR. Click Browse to select the patch file in the local directory. Factory Reset Choose (Parameter Configuration) > System Management > Factory Reset. The Factory Reset page is displayed.
NVR User Manual Click Reboot button, then click OK button in the pop-up message box.The NVR system will reboot. Auto Restore Choose (Parameter Configuration) > System Management > Auto Restore. The Auto Restore page is displayed. You can configure the Date and Time. The NVR system will be maintained at the setting time. 3.5 Playback Choose (Playback), you can play the recording file of the NVR. 1．Select a date with recording in calendar.
NVR User Manual 3．Click Search button to search the matched recorded files. If there are search results, then they will be shown in the time bar area. 4．Manage the recording. Icon Description Start Stop Fast backward. The fast backward speed can be 4 times, 8 times, 16 times or 32 times of the normal playing speed. Click this button. The multiple of normal playing speed is displayed in the upper right corner of the playback page.
NVR User Manual Full screen. Make the playing video maximized. After the video is maximized, press ESC to exit full screen. 5．Playback time You can move the mouse to a specific time axis and click to watch the playback. Icon Description Zoom-in time axis. Zoom-out time axis. www.foscam.
NVR User Manual 4 Appendix 4.1 HDD Capacity Calculation This chapter describes how to determine the size of the HDD you need when you install the NVR for the first time. The NVR adopts the MPEG4 / H.264 compression technology and its dynamic range is large. Therefore, the capacity of the HDD depends on the estimated size of files generated in each channel every hour according to code streams.
NVR User Manual Whole HDD Capacity(M)=4*168(hour) * 1800(M/hour) =1209600M, 1209600M= 1209600M =1181.25G 1024 According to the preceding calculation result, you are advised to buy a HDD of 1.5 TB or above. 4.2 Common Operations 1. Third Party Domain Name Settings User can also use third part DDNS, such as www.no-ip.com, www. 3322.com Here take www.no-ip.com for example: Step 1, Go to the website www.no-ip.com to create a free hostname Firstly: Login on www.no-ip.com and click No-IP Free to register.
NVR User Manual Click here to register . Figure 4.27 Please register an account step by step according to instructions on www.no-ip.com. After registration, please login your email which used to register. You will receive an email from website, please click the link to activate your ACCOUNT as indicated in email. Secondly: Login the link with the registered username and password to create your domain name. www.foscam.
NVR User Manual Please create the domain name step by step according to instructions on www.no-ip.com Step 2, DO DDNS Service Settings within the NVR Please set DDNS Settings within the NVR by hostname, a username and password you've got from www.no-ip.com Take hostname ycxgwp.no-ip.info, username foscam, password foscam2012 for example. Firstly, goes to option of DDNS Settings on the administrator panel. Secondly, select No-Ip as a server..
NVR User Manual Firstly, login the router, goes to the menu of Port Forwarding or Port Trigger (or named Virtue Server on some brands of router). Take Linksys brand router as an example, Login the router, and goes to Applications & Gaming > Single Port Forwarding. Secondly, Create a new column by LAN IP address & HTTP Port No. of the NVR within the router showed as below. Assign a name as you like here . Fill the Media Port no. of the camera on the column of External Port and Internal Port .
NVR User Manual The subnet mask of the NVR must be the same as the subnet mask in LAN port status. The default gateway of the NVR is the same as the IP address in LAN port status. The primary DNS and secondary DNS can be the same as the DNS in WAN port status. www.foscam.
NVR User Manual 4.3 Specifications NVR Model Video Input Video Output FN3108E IP Video Input 8 Channels HD IP camera input HD-OUT 1 * HD-OUT VGA Output 1 * VGA Display Resolution Recording 1920 * 1080 / 60Hz, 1280 * 720 / 60Hz, 1440 * 900 / 60Hz, 1024 * 768 / 60Hz Recording Resolution 720P per channel (8ch@720P) Record Mode Manual / Time Scheduled / Motion Detect Compression Format H.
NVR User Manual Language Internet Viewing Microsoft IE8 and above version, Safari Smart phone iOS, Android, 3G / 4G Smartphones Chinese, English, French, Hungarian, Czech, Dutch, Greek, Russian, Polish, Spanish, Portuguese, Italian, German, Finland Power Supply Dimension (L x W x H) Physical and Environmental DC 48V / 1.87A 234mm * 234mm * 52mm / 9.2in x 9.2in x 2in Net Weight 1200g / 2.
NVR User Manual 802.3af PoE Connectivity Software Features Ethernet RJ45 Video Format H.264 Multi-Stream Dual streams Motion Detection UPnP Day / Night Physical and Environmental Waterproof IP66 Net Weight 255g / 0.6lb Power DC12V Power Consumption < 5W Dimension (LxWxH) 97mm * 67mm * 64mm / 3.8in * 2.6in * 2.
NVR User Manual 4.4 FAQ 1. No image displayed on the monitor after starting up normally. Verify the device is connected with the monitor via HD-OUT or VGA cable. Verify the connection cable is good. Verify Input mode of the monitor is correct. Please check the input mode of the monitor matches with the output mode of the device (e.g. if the output mode of NVR is HD-OUT output, then the input mode of monitor must be the HD-OUT input). And if not, please modify the input mode of monitor. 2.
NVR User Manual 7. Why can't video files be downloaded during video playback or downloaded files cannot be played back properly? To save consumed resources, the server limits concurrency of video playback and file download. In this case, stop video playback and then download files or play back videos after video files are downloaded. 8. Why does the Web client prompt TIME OUT after you enable or disable UPNP in network settings? In this case, the server restarts some applications.
NVR User Manual 4.5 Glossary Acronym Term Description Dynamic DNS is a method, protocol, or network service that provides the capability for a networked device, such as a router or DDNS Dynamic Domain computer system using the Internet Protocol Suite, to notify a Name Server domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured hostnames, addresses or other information stored in DNS.
NVR User Manual 4.6 CE & FCC Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
NVR User Manual 4.7 WARRANTY FOSCAM values your business and always attempts to provide you the very best of service. No limited hardware warranty is provided by FOSCAM unless your FOSCAM product ("product") was purchased from an authorized distributor or authorized reseller. Distributors may sell products to resellers who then sell products to end users.
NVR User Manual Replacement Services If customers ask for replacement service, please contact point-of-purchase and follow their policy. Our technicians will inspect all items returned for replacement requests. If the retuned product is found in working order, we will return the same item received. However customers shall be responsible for all shipping & handling charges incurred for getting the units back to customers.
NVR User Manual Shipping Fee If products are defective or damaged under normal use or operation in the replacement limit, distributors or resellers are responsible for the shipping cost the product back to customers, customers should assume the shipping cost send the product to the point-of-purchase. During replacement limit, if customers ask for replacement due to the product does not fit for customer's personal expectation, customers should responsible for both shipping fee.
NVR User Manual All rights reserved. FOSCAM and the FOSCAM logo are trademarks of ShenZhen FOSCAM Intelligent Technology Limited., registered in the U.S. and other countries. 4.8 Statement You are advised to be cautious in daily life, keep personal account information carefully, do not share personal account easily. Change passwords of your account and equipment periodically, and upgrade equipment firmware to strengthen security consciousness.
NVR User Manual purchased by the customer. Without the prior written permission of Foscam company, all the contents of relevant operating instructions manual affiliated to the product must not be reproduced, transmitted, transcribed or stored in a retrieval system, or translated into other languages. Our company will reserve the right to improve and modify the product and corresponding manuals. The company reserves the right of final interpretation on our products. 4.
