User's Manual

ManualsBrandsFOSHAN SHUNDE ATOLL TRADING ManualsElectronicsRemote control

User Manual (EN)

Connecting the remote control

WARN:Changes or modifications to this unit not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the

device.

 A New remote control has to establish a new connection to the cooker hood when used for first time. One

remote control could possibly control several cooker hood at the same time.

Connection process between remote control and cooker hood

 Within 15 seconds after the cooker hood connects to the power supply, long press

for 5 seconds, the

indicators light begin flashing from one button to another, the cooker hood is in connection mode, press

any button on remote control to confirm the connection. The connection process finished and the remote

Summary of content (6 pages)

PAGE 1
User Manual (EN) Connecting the remote control WARN:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
control can be used for speed selection, lighting and timer setting.  If you want to connect again, you will need to clear the code that has been set up previously.  To clear the code, press for 5 seconds, the indicators light begin flashing from one button to another, the cooker is in connection mode. Then, press again for 5 seconds, the previous connection code is cleared.
PAGE 3
2.2When the motor works at low speed, press again, the motor will change to middle speed. 2.3 Base on the middle speed condition, press again, the motor will change to the high speed. 2.4 Base on the high speed condition, press again,the hood will still work at high speed. 3. Turning off/Decreasing motor speed button 3.1 Press the and the motor will be shift to a lower speed. Repeating press the button, it will keep on decreasing the motor speed till the cooker hood turning off.
PAGE 4
Manuel d'utilisateur (FR) Connection de télécommande AVERTISSEMENT: Les changements ou les modifications de cet appareil non expressément approuvées par la partie responsable de conformité peuvent annuler le droit d’utilisateur du fonctionnement d’équipement. REMARQUE: Cet équipement a été testé et déclaré conforme aux limites de l’appareil numérique de classe B, selon la partie 15 des règles de FCC.
PAGE 5
Processus de connection entre la télécommande et la hotte ※Dans 15 secondes après la connection de hotte à l'alimentation électrique, appuyez longuement sur pendant 5 secondes, les voyants commencent à clignoter d'un bouton à un autre bouton, la hotte est mise en mode de connection, appuyez sur tout bouton de télécommande pour confirmer la connection. Le processus de connection est terminé et la télécommande peut être utilisée pour la sélection de vitesse, l'éclairage et le réglage de minuterie.
PAGE 6
2.Allumez/augmentez le bouton de vitesse de moteur , le moteur possède totalement 3 niveaux, tels que le bas niveau, le moyen niveau et le haut niveau. 2.1 Appuyez à une fois sur , le voyant sera allumé et le moteur fera le fonctionnement à la basse vitesse. 2.2. Lorsque le moteur fait le fonctionnement à la basse vitesse, appuyez à nouveau sur , le moteur passera à la moyenne vitesse. 2.3．Dans la condition de moyenne vitesse, appuyez à nouveau sur , le moteur passera à la haute vitesse. 2.4.