Digital Multitracker Owner's Manual VF08

45
Mixer Functions
Effect parameter details
The parameters that can be adjusted will depend on the parameter type.
Reverb effect parameters (parameter type: REVERB)
For effect types 1--24 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. Eff Level Adjust the effect return level: 0~99
2. Rev Time Adjust the length of reverberation. Range: 0.1--9.9 seconds
3. Pre Delay Adjust the time from the original sound until reverberation begins. Range: 0--100 ms
4. Hi Ratio Adjust the decay ratio of the high frequencies. Range: 0--10
5. E/R Level Adjust the volume of the early reflections. Range: 0--99
Delay+reverb effect parameters (parameter type: DELAY+REVERB)
For effect types 25--28 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. Eff Level Adjust the effect return level: 0~99
2. Delay Time Adjust the delay time: Range: 1--230 ms
3. Feedback Adjust the number of delay repeats. Range: 0--99
4. Delay Bal Adjust the delay balance. Range: 0--99
5. Rev Time Adjust the length of reverberation. Range: 0.1--9.9 seconds
Delay effect parameters (parameter type: DELAY)
For effect types 29 and 30 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. Eff Level Adjust the effect return level: 0~99
2. Delay Time Adjust the delay time. Range: 1--680 ms
3. Feedback Adjust the number of delay repeats. Range: 0--99
4. Hi Ratio Adjust the decay ratio of the high frequencies. Range: 0--10
5. Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
* H1~H9 = HPF (larger numbers will raise the cutoff frequency)
BPM delay effect parameters (parameter type: BPM DELAY)
For effect types 31 and 32 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. Eff Level Adjust the effect return level: 0~99
2. BPM Adjust the BPM. Range: 30--250 bpm
3. Note Select the note value for the delay. Range: 24, 16, 8T, 16...8, 4T, 8., 4, 2T, 4., 2, 2., 1
* 24 = 16th note sextuplets, 16 = 16th notes, 8T = 8th note triplets, 16. = dotted sixteenth notes,
8 = 8th notes, 4T = quarter note triplets, 8. = dotted eighth notes,
4 = quarter notes, 2T = half-note triplets, 4. = dotted quarter notes, 2 = half notes
* The "." shown in the ninth character of the LCD indicates a dotted note.
* The "T" shown in the ninth character of the LCD indicates a triplet.
4. Feedback Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
5. Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
* H1~H9 = HPF (larger numbers will raise the cutoff frequency)
Short delay effect parameters (parameter type: SHORT DELAY)
For effect type 33 of the preceding "Effect type" table, the following four parameters can be adjusted.
1. Eff Level Adjust the effect return level: 0~99
2. Delay Time Adjust the delay time. Range: 0.1--9.9 ms, 10--99 ms, 100--200 ms
3. Feedback Adjust the number of delay repeats. Range: 0--99
4. Hi Ratio Adjust the decay ratio of the high frequencies. Range: 0--10
5. Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
* H1~H9 = HPF (larger numbers will raise the cutoff frequency)
Doubling effect parameters (parameter type: DOUBLING)
For effect type 34 of the preceding "Effect type" table, the following three parameters can be adjusted.
1. Eff Level Adjust the effect return level: 0~99
2. Lch Delay Adjust the delay time of the L channel. Range: 0.1--9.9 ms, 10--99 ms, 100--200 ms
3. Rch Delay Adjust the delay time of the R channel. Range: 0.1--9.9 ms, 10--99ms, 100--200 ms
4. Filter Adjust the tone of the delay sound. Range: L9~L1, OFF, H1~H9
* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
* H1~H9 = HPF (larger numbers will raise the cutoff frequency)