Lateral File NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Assembly Tools Required 3 Hardware Identification 4-5 Hardware Usage Guide 6 Assembly Steps 7-28 No.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER 1. 2. Push a TWIST-LOCK FASTENER into the large hole in the part. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2. Tighten the FASTENER with a Phillips screwdriver as tight as possible. Dowel end HOW TO USE A HIDDEN CAM & CAM SCREW Cam Screw Arrow 1.
Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push four TWIST-LOCK FASTENERS (37F) into the large holes in the ENDS (A and B). å Insert four WOOD DOWELS (15F) into the ENDS (A and B). Some assembly (and snacks) required. Do not tighten the TWIST-LOCK FASTENERS in this step. 15F A B Meet Parts (A and B). These components have been engineered to be lighter, stronger, faster… well ok. Not technically faster.
Step 2 å Separate the EXTENSION SLIDES (40MC) from the EXTENSION RAILS (40MA) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (40MA) to the ENDS (A and B). Use eight SILVER 1/2" FLAT HEAD SCREWS (128S) through holes #1 and #4. å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END.
Step 3 å Fasten the INTERLOCK MECHANISM (34G) to the RIGHT END (A) exactly as shown. Use three BLACK 9/16" PAN HEAD SCREWS (51S). å Fasten the L-LOCK BRACKET (76G) to the RIGHT END (A) exactly as shown. Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 4 å Push eight TWIST-LOCK FASTENERS (37F) into the large holes in the BACKS (J). å Insert eight WOOD DOWELS (15F) into the BACKS (J). Do not tighten the TWIST-LOCK FASTENERS in this step.
Step 5 å Fasten the BACKS (J) to the RIGHT END (A). Tighten four TWIST-LOCK FASTENERS. å NOTE: Be sure the WOOD DOWELS in the BACKS insert into the END. J J STWI RS T ith NE ce w ASTE a f r Su CK F LO IST W S T ith ENER w e ST fac Sur CK FA LO These edges must be even. Edge with TWIST-LOCK FASTENERS A These edges must be even.
Step 6 å Push four TWIST-LOCK FASTENERS (37F) into the large holes in the BOTTOM (G). Do not tighten the TWIST-LOCK FASTENERS in this step.
Step 7 å Fasten the BOTTOM (G) to the RIGHT END (A). Tighten two TWIST-LOCK FASTENERS. G A These holes must be here.
Step 8 å Fasten the LEFT END (B) to the BOTTOM (G) and BACKS (J). Tighten six TWIST-LOCK FASTENERS. å NOTE: Be sure the WOOD DOWELS in the BACKS insert into the END.
Step 9 å Fasten the TOP (F) to the ENDS (A and B). Tighten four TWIST-LOCK FASTENERS. å NOTE: Be sure the WOOD DOWELS in the ENDS insert into the TOP. Hey! It's starting to look like something! B F These holes must be here.
Step 10 å Fasten four METAL BRACKETS (4G) to the TOP MOLDING (C). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edge of the MOLDING. å Fasten the TOP MOLDING (C) to the TOP (F). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the MOLDING and into the holes in the TOP.
Step 11 å å Carefully turn your unit onto the top. å Fasten two METAL BRACKETS (4G) to the BOTTOM (G). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edge of the BOTTOM. Fasten two CORNER BRACKETS (31G) to the ENDS (A and B) and BOTTOM (G) exactly as shown. Use eight BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 12 å Fasten the BASE (H) to the BOTTOM (G). Use six BLACK 9/16" LARGE HEAD SCREWS (1S) through the BRACKETS on the BOTTOM and into the holes in the BASE.
Step 13 å Fasten the Z-LOCK BRACKET (77G) to the UPPER DRAWER FRONT (D) exactly as shown. Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Turn two CAM SCREWS (8F) into the DRAWER FRONTS (D and E).
Step 14 1 The tabs should insert freely into the slots. Gently tilt the DRAWER SIDES side to side until the tabs slip into the slots. 2 With the palm of your hand, tap the DRAWER BOTTOM down into the groove. Unfi sur nished fac e D547 D729 D547 E D548 Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove. Groove å D548 E å Insert the DRAWER SIDES (D547 and D548) at an angle into the slot at each end of the LOWER DRAWER FRONT (E).
Step 15 å Fasten two FILE BRACKETS (12B) to the LOWER DRAWER FRONT (E) and DRAWER BACK (D61) exactly as shown. Use four BROWN 7/16" LARGE HEAD SCREWS (6S). å Repeat this step for the other drawer.
Step 16 å å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D547 and D548). å NOTE: The screw head in the CAM must be visible through the slotted hole in the SLIDE. å Repeat this step for the other drawer. Fasten the EXTENSION SLIDES (40MC) to the DRAWER SIDES (D547 and D548). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #4.
Step 17 å å NOTE: Pay close attention to the locations of the DRAWER ACTUATORS (62G) in this step. å Fasten the other DRAWER ACTUATOR (62G) to the RIGHT DRAWER SIDE (D547) above the SLIDE on the LOWER DRAWER (E). Use three BLACK 1/2" FLAT HEAD SCREWS (11S). Fasten one DRAWER ACTUATOR (62G) to the RIGHT DRAWER SIDE (D547) below the SLIDE on the UPPER DRAWER (D). Use three BLACK 1/2" FLAT HEAD SCREWS (11S). D547 D 62G This ACTUATOR is below the SLIDE. The BRACKET must be here.
Step 18 å Fasten two PULLS (191K) to the LOWER DRAWER FRONT (E). Use four BLACK 7/8" MACHINE SCREWS (37S). å Repeat this step for the other drawer.
Step 19 å Press a FILE GLIDE (6B) onto the top edge of the RIGHT DRAWER SIDE (D547). å Slide the FILE RODS (9B) through a FILE BAR (1B), through the holes in the FILE BRACKETS (12B), through another FILE BAR (1B), and into the FILE GLIDE (6B) on the RIGHT DRAWER SIDE (D547). å Slide another FILE GLIDE (6B) onto the other ends of the FILE RODS (9B), then press this FILE GLIDE over the LEFT DRAWER SIDE (D548). å Repeat this step for the other drawer.
Step 20 å Fasten the LOCK PACK (21J) to the LOWER DRAWER FRONT (E) in the exact order shown. å å NOTE: It is important to position the CAM exactly as shown. Almost time to celebrate! With a nap. NOTE: Turn the KEY clockwise to lock. WASHER CAM NUT The prongs must press into the FILE DRAWER FRONT as you tighten the NUT with an Adjustable Wrench.
Step 21 å å å Carefully stand your unit upright. å å å NOTE: The lower DRAWER ACTUATOR will be near the top of the RIGHT DRAWER SIDE as shown in Diagram 2. Pull the lower wing of the INTERLOCK MECHANISM (34G) forward until it clicks into place as shown in Diagram 1. To insert the lower drawer into your unit, line up the EXTENSION SLIDES on the drawers with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer it is fully inserted.
Step 22 å To make adjustments to the drawer, loosen SCREW #4 in the SLIDES a 1/4 turn, then turn the cam clockwise or counter-clockwise. Notice how the drawer raises or lowers as you turn the cam. By adjusting the drawer this way, it will help the DRAWER FRONT line up better when closed. Tighten the SCREWS when finished with adjustments. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth. Wipe dry.
Classeur latéral Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage. REMARQUE : CE MANUEL D’INSTRUCTIONS CONTIENT D’IMPORTANTES INFORMATIONS RELATIVES À LA SÉCURITÉ. À LIRE ET CONSERVER POUR TOUTE RÉFÉRENCE FUTURE.
Guide d'utilisation de la visserie ÉTAPE 3 UTILISATION DE LA FIXATION TWIST-LOCK Fixer le MÉCANISME DE VERROUILLAGE (34G) à l’EXTRÉMITÉ DROITE (A) exactement comme il l’est indiqué. Utiliser trois VIS TÊTE GOUTTE DE SUIF 14 mm NOIRES (51S). 1. Enfoncer une FIXATION TWIST-LOCK dans le gros trou de la pièce. 2. 1. Insérer l'extrémité filetée de la FIXATION dans le trou de la pièce attenante.
ÉTAPE 9 ÉTAPE 14 Fixer le DESSUS (F) aux EXTRÉMITÉS (A et B). Serrer quatre FIXATIONS TWIST-LOCK. 1. Insérer les CÔTÉS DE TIROIR (D547 et D548) en biseau dans la fente dans chaque extrémité du DEVANT DE TIROIR INFÉRIEUR (E). REMARQUE : S’assurer d’insérer les CHEVILLES EN BOIS dans les EXTRÉMITÉS dans le DESSUS. 2. Enfiler le FOND DE TIROIR (D729) dans les rainures des CÔTÉS DE TIROIR (D547 et D548) et du DEVANT DE TIROIR INFÉRIEUR (E).
ÉTAPE 18 ÉTAPE 21 Fixer deux POIGNÉES (191K) au DEVANT DE TIROIR INFÉRIEUR (E). Utiliser quatre VIS À MÉTAUX 22 mm NOIRES (37S). Relever, avec précaution, l'élément dans sa position verticale. Répéter cette étape pour l'autre tiroir. ÉTAPE 19 Enfoncer une ARMATURE POUR DOSSIERS (6B) sur le bord supérieur du CÔTÉ DROIT DE TIROIR (D547).
Archivero Lateral Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje. NOTA: ESTE FOLLETO DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE SOBRE LA SEGURIDAD. POR FAVOR LEA Y GUÁRDELO PARA REFERENCIA EN EL FUTURO.
Guía de uso de herrajes PASO 3 CÓMO UTILIZAR EL SUJETADOR TWIST-LOCK Fije el MECANISMO DE UNIÓN (34G) al EXTREMO DERECHO (A) exactamente como se muestra. Utilice tres TORNILLOS NEGROS DE CABEZA REDONDA de 14 mm (51S). 1. Empuje un SUJETADOR TWIST-LOCK dentro del agujero grande en la parte. 2. 1. Inserte el extremo con cabilla del SUJETADOR en el agujero de la parte adjunta.
PASO 9 PASO 14 Fije el PANEL SUPERIOR (F) a los EXTREMOS (A y B). Apriete cuatro SUJETADORES TWIST-LOCK. 1. Inserte los LADOS DE CAJÓN (D547 y D548) en ángulo en el encaje en cada extremo de la CARA DE CAJÓN INFERIOR (E). NOTA: Asegúrese de que los PASADORES DE MADERA en los EXTREMOS se inserten en el PANEL SUPERIOR. 2. Deslice el FONDO DE CAJÓN (D729) en las ranuras de los LADOS DE CAJÓN (D547 y D548) y de la CARA DE CAJÓN INFERIOR (E). PASO 10 3.
PASO 18 PASO 21 Fije dos TIRADORES (191K) a la CARA DE CAJÓN INFERIOR (E). Utilice cuatro TORNILLOS NEGROS PARA METAL de 22 mm (37S). Cuidadosamente ponga la unidad en posición vertical. Repita este paso para el otro cajón. PASO 19 Empuje un CORRIMIENTO DE ARCHIVERO (6B) sobre el borde superior del LADO DERECHO DE CAJÓN (D547).
CAUTION Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading drawers. Place the heavier items in the lower drawer.
PRECAUCIÓN Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones sobrecargados. • Riesgo de lesiones. • La caída de mobiliario inestable. • Los cajones sobrecargados pueden romperse. • Nunca exceda los límites de peso indicados en las instrucciones. • Para cargar los cajones trabaje desde abajo hacia arriba.
5-YEAR LIMITED WARRANTY 1. We provide limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
