Installation

CAUTION: PULL ANY EXCESS WIRE THROUGH BOTTOM OF THE LAMP. PLEASE USE TYPE
T8 BULB. DO NOT USE LIGHT BULB RATED GREATER THAN 3.5 WATT LED BULB.
OR THE LAMP MAY BURN AND CAUSE A FIRE! TO CLEAN, USE A SOFT CLOTH ONLY.
NOTE:TURN THE POWER OFF(UNPLUG FROM THE WALL OUTLET) BEFORE REPLACING
THE BULB. MAKE SURE THE BULB HAS SUFFICIENT TIME TO COOL DOWN. DO NOT
SUBJECT THE LAMP TO ANY SHOCK WHILE LIT AS SHATTERING OF LAMP MAY RESULT.
INSTALLATION
INSTALLATION INSTRUCTION FOR PENDANT LAMP
INSTALLATION:
white wire in the electrical box.
STYLE #1-Using thumb screws
the groove or holes in the glass.
nut from socket. Position glass
socket. Slide the glass over the
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
DO NOT REMOVE INSULATION FROM FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND WIRE
(BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
1. Refer to the mounting
bracket style that
matches the bracket that
is included with your
fixture.
Style#1 -Loosen hex nut
“A” and “B”. Adjust stud
so it clears the fixture
once assembled. Hold in
place with “A” and lock in
place with “B”.
Style#2 (Threaded holes)
Loosen “B”. Adjust stud to
desired length and lock in
place with “B”.
2.Attach the mounting
bracket to outlet box
using outlet box screws.
(not included).
3. Adjusting the length of
flexible cord. For safety,
do not release the knot
inside canopy.
STYLE #1- Loosen the
plastic screw for adjusting
the length of flexible cord.
Re-tighten plastic screw
after adjusting.
STYLE #2- Adjust the
height of the fixture by
pushing the button.
Ensure the cord does not
touch the light bulb(s)
when adjusting the height
of the fixture or the steel
cable(s).
4. Connect the ground wire
(bare copper or green) from
your fixture to the ground
wire (bare copper or green)
or ground screw in the
electrical outlet box. Connect
the black wire (or wire with
marketing) from the fixture to
the black wire in the electrical
box and connect the white
wire from the fixture to the
5. Tuck electrical wires into
outlet box and position fixture
over studs or nipple on
mounting bracket assembly.
Secure fixture in place with
star washer(s) and cap nut(s).
6.Mounting Glass To Fixture
NOTE: Refer to the style of
assembly that matches the
style of your fixture.
provided, attach the glass to
the fixture head. Place the
glass into the fixture head.
Place the glass into the fixture
head and tighten screws into
STYLE #2-Remove spinner
on lamp and secure with
spinner nut. On some fixtures,
a tool is included to attach the
spinner nut.
STYLE #3-Squeeze the two
clips together around the
clips, then push the glass up
snug to the fixture head.
7. If not already done, install
proper bulb type and wattage
(not included).
2
1. SCREW THE RODS [B] AND CANOPY [C] TO THE FIXTURE [A].
2. ATTACH THE CIRCLE CROSS BAR [D] TO THE OUTLET BOX USING OUTLET BOX SCREWS [E].
3. CIRCLE CROSS BA DECORATIVE NUT [H].PLACE THE CANOPY [C] ONTO THE R [D], THEN SCREW WITH
4. INSTALL BULBS. (BULBS INCLUDED)