Installation Manual

Page 48
© 2015 Sensata Technologies
Appendix A – Specifi cations and Optional Equipment
Table A-1, MS-PAE Specifi cations (at 25°C)
Appendix A – Specifi cations and Optional Equipment
Models MS4024PAE MS4448PAE
Inverter Specifi cations
Input battery voltage range 18.0 to 34.0 VDC 36.0 to 64.0 VDC
Absolute maximum DC input 50 VDC 68 VDC
Nominal AC output voltage 120/240 VAC split phase
AC output voltage accuracy L-N: 120 VAC ±5%, L-L: 240 VAC ±5% (≤ continuous power)
Output frequency and accuracy 60 Hz ± 0.1 Hz
Total Harmonic Distortion (THD) < 5%
Continuous power output at 25°C 4000 VA (L-L) 4400 VA (L-L)
Continuous AC output current L-N: 27.0 A/120 VAC, L-L: 16.7 A/240 VAC L-N: 29.7 A/120 VAC, L-L: 18.3 A/240 VAC
1 msec surge current (AAC) L-N: 120, L-L 70
100 msec surge current (AAC) L-N: 72, L-L 40 L-N: 75, L-L 40
5 sec surge power (real watts) 5800 8500
30 sec surge power (real watts) 5200 6000
5 min surge power (real watts) 4800 5400
30 min surge power (real watts) 4500 4800
Max. continuous input current 266A 144A
Inverter effi ciency (peak) 93% 94%
Transfer time 16 msecs
Search mode (typical) < 6 watts
No load (120 VAC output, typical) 27 watts 25 watts
Waveform Pure Sine Wave
Charger Specifi cations
AC input range 60 to 140 VAC / 50 to 70 Hz
Continuous output at 25°C 105 ADC 60 ADC
Charger effi ciency 85%
Power factor > 0.95
Input current at rated output 15 AAC/leg at 120/240 VAC split phase 17.5 AAC/leg at 120/240 VAC split phase
General Features and Capabilities
Transfer relay capability 2 legs at 30A per leg transfer standard
Five-stage charging capability Bulk, Absorb, Float, Equalize (requires remote), and Battery Saver™
Battery temp compensation Yes, 15 ft Battery temp sensor standard
Internal cooling 0 to 120 cfm variable speed drive using dual 92 mm brushless DC fans
Overcurrent protection Yes, with two overlapping circuits
Over-temperature protection Yes on transformers, MOSFETS, and battery
Corrosive protection PCBs conformal coated, powder-coated chassis & top, stainless steel fasteners
Listings ETL Listed to ANSI/UL1741, 1st edition, and CSA STD C22.2 No. 107.1-01
Warranty (Parts & Labor) 3 yrs parts and labor (extends to 5 yrs when purchased with and installed on MP/MMP system)
Environmental Specifi cations
Operating temperature –20°C to +60°C (-4°F to 140°F)
Non-operating temperature –40°C to +70°C (-40°F to 158°F)
Operating humidity 0 to 95% RH non-condensing
Physical Specifi cations
Unit Dimensions (L x W x H) 13.75” x 12.65” x 8.0” (34.9 cm x 32.1 cm x 20.3 cm)
Shipping dimensions (L x W x H) 18.5” x 17.5” x 12.5” (47 cm x 44.5 cm x 31.8 cm)
Mounting Shelf, wall (no vents on bottom), MP or MMP panels
Unit/Shipping weight 55 lb (24.9 kg) / 62 lb (28.2 kg) 55 lb (24.9 kg) / 63 lb (29.6 kg)