WBU058‐LGA IEEE 802.11 a/b/g/n/ac/ax 2x2 + Bluetooth v5.2 Wireless Adapter 1 Ver.
CHAPTER 1. MODULE OVERVIEW The Foxconn WBU058-LGA is a highly integrated module which features a high performance 2x2 dual-band WLAN subsystem and a Bluetooth v5.2 subsystem. The WLAN subsystem contains the 802.11a/b/g/n/ac/ax radio, baseband that are designed to meet feature-rich wireless connectivity at high standards, and delivering reliable, cost-effective throughput from an extended distance. Optimized RF architecture and baseband algorithms provide superb performance and low power consumption.
CHAPTER 2. ELECTRICAL AND RF SPECIFICAITONS 2-1 Recommended Operation Rating Table 2 Operation Rating Parameter Condition Min Typ. Max. Unit DVDD 3.3 3.0V 3.3V 3.6V V RF Interface Zo 50 Ohm 2-2 Digital IO Pin DC Characteristic Table 3 CN1 UART IO Characteristic Symbol VIH VIL VOH VOL Parameter Min. Typ. Max Units High-level input Voltage Vcc*0.7 - - V Low-level input Voltage - - Vcc*0.3 V 3.8 - - V - - 0.
2-5 MECHANICAL SPECIFICATION 4 Ver.
CHAPTER 3. ADDITIONAL INFORMATION 3-1 Environment Specifications Operating Conditions Operation Temperature : -10 ~ 80℃ Relevant Humidity: 5 ~ 95% (non-condensing) Storage Conditions Non-Operation Temperature : -20 ~ 85℃ (Typ. 25℃) Relevant Humidity: 5 ~ 95% (non-condensing) 3-2 Guarantee period / Failure rate Guarantee period Guarantee period is 12 months after manufacture’s factory shipment Failure rate 600fit 5 Ver.
CHAPTER 4: REGULATORY STATEMENT FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. 3) PFF restriction: ⦁ FCC regulations restrict the operation of this device to indoor use only.
Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users.
OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules.
ISED Statement: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de classe B est conforme à la norme canadienne ICES‐003. This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device is intended only for OEM integrators under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna. As long as above conditions is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Manual Information To the End User The end user manual shall include all required regulatory information/warning as shown in this document. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Antennas The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. This radio transmitter [2878F-WBU058LGA] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated.
