Trademarks FOXWELL is trademark of Shenzhen Foxwell Technology Co., Ltd. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information ©2015 Shenzhen Foxwell Technology Co., Ltd. All rights reserved. Disclaimer The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice. Visit our website at: www.foxwelltech.
One-Year Limited Warranty Subject to the conditions of this limited warranty, Shenzhen Foxwell Technology Co., Ltd (“FOXWELL”) warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one (1) year.
a) The customer shall return the product to the place of purchase for repair or replacement processing, contact your local FOXWELL distributor or visit our website www.foxwelltech.com to get further information. b) The customer shall include a return address, daytime phone number and/or fax number, complete description of the problem and original invoice specifying date of purchase and serial number. c) The customer will be billed for any parts or labor charges not covered by this limited warranty.
SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY, OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED. 6. Some states do not allow limitation of how long an implied warranty lasts, so the one-year warranty limitation may not apply to you (the Consumer). Some states do not allow the exclusion or limitation of incidental and consequential damages, so certain of the above limitations or exclusions may not apply to you (the Consumer).
Safety Information For your own safety and the safety of others, and to prevent damage to the equipment and vehicles, read this manual thoroughly before operating your tester. The safety messages presented below and throughout this user’s manual are reminders to the operator to exercise extreme care when using this device. Always follow all BCI (Battery Council International) safety recommendations. Read, understand and follow all safety messages and instructions in this manual.
Table of Contents ONE-YEAR LIMITED WARRANTY .........................................................................................................2 SAFETY INFORMATION ........................................................................................................................ 5 SAFETY MESSAGE CONVENTIONS USED .................................................................................................5 IMPORTANT SAFETY INSTRUCTIONS ..........................................................
1 Using This Manual We provide tool usage instructions in this manual. Below is the conventions we used in the manual. 1.1 Bold Text Bold text is used to highlight selectable items such as buttons and menu options. Example: Press the ENTER button to select. 1.2 Symbols and Icons 1.2.1 Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot ●. Example: When System Setup is selected, a menu that lists all available options displays.
Example: NOTE Test results do not necessarily indicate a faulty component or system. Important IMPORTANT indicates a situation which, if not avoided, may result in damage to the test equipment or vehicle. Example: IMPORTANT Do not soak product as water might find its way into the tester. 2 Introductions The latest BT-705 Battery Analyzer from Foxwell is dedicatedly developed to test 6V & 12V regular flooded, AGM flat plate, AGM spiral and gel batteries and 12V & 24V starting and charging system.
A LCD Display - shows menus, test results and operation tips. B Menu Button - access the Main Menu options of the tester. C BACK Button - exits a screen and generally returns to previous screen. D UP and Down Buttons - selects an option or scroll to menu options. E Left and Right Buttons - moves the cursor left or right to select characters when inputting the plate number of the car. F ENTER Button - executes a selected option and generally goes to the next screen.
2 Nylon Carry Pouch - stores the tester and its accessories. 3 Bluetooth printer (Optional)- let you to print out the test results. 2.3 Specifications Display: 128 * 64 pixels, large, backlit display screen Working Temperature: -20 to 60°C (-4 to 140°F) Storage Temperature: -20 to 70°C (-4 to 158°F) Power Supply: 8-30V DC Dimensions (L*W*H): 190*90*36mm Gross Weight (without printer): 1.6 KG Gross Weight (with printer): 2.
5. Press the MENU button to go to the Main Menu. NOTE Do not connect the tester to a voltage source greater than 30VDC; otherwise you may damage the tester. NOTE If you are testing inside a vehicle, make sure all accessory loads are cut off, the key is not in the ON position and the doors are closed. 3.2 Battery Test Battery Test menu lets you analyze the battery healthy status to calculate the actual cold cranking capability of the battery and the aging status.
1. Scroll with the UP or DOWN button to highlight Battery Test from Main Menu and press the ENTER key. 2. Scroll with the UP or DOWN button to highlight the voltage from Main Menu and press the ENTER key. 3. Scroll with the UP or DOWN button to highlight OUT OF VEHICLE or IN VEHICLE from BATTERY LOCATION menu and press ENTER to select the battery location. 4. Scroll with the UP or DOWN button to highlight TOP POST or SIDE POST from POST TYPE menu and press ENTER to select the battery post type.
5. Scroll with the UP or DOWN button to select the battery type from BATTERY TYPE menu and press ENTER to confirm. 6. Scroll with the UP or DOWN button to select the battery standard from BATTERY STANDARD menu and press ENTER to confirm. Not all rating systems are available for each application. You may find the battery type and battery rating label on every battery. 13 BT705 Battery Analyzer User’s Guide - English Version_V1.
Global Rating Systems No. Standard Description BT705 Testing Range 1 CCA Cold Cranking Amps, as specified by SAE.
No. Test Results 1 GOOD BATTERY 2 GOOD-RECHARGE 3 CHARGE & RETEST 4 REPLACE BATTERY 5 BAD CELL-REPLACE Interpretation The battery is in good condition. The battery is in good condition but low current. Fully charge the battery and return it to service. Fully charge the battery and retest. Failure to fully charge the battery before testing may result in inaccurate results. If you still get CHARGE & RETEST message after you fully charge the battery, replace it.
To start cranking test: 1. Press the ENTER button for cranking test. 2. Start the engine when prompted. 3. The tester displays the decision on the starter system, cranking voltage, and cranking time in milliseconds. No. 1 2 3 Test Results Interpretation CRANKING NORMAL LOW VOLTAGE The starter voltage is normal and the battery is fully charged. The starter voltage is low and the battery is fully charged. The starter voltage is low and the battery is discharged.
3.4 Charging System test Once you have completed an in-vehicle test, the display alternates between the battery test results and the message press ENTER for charging test. Press ENTER to proceed with the charging test. To start charging system test: 1. Follow the on-screen prompts to Rev the engine. 2. Turn on high beams headlights and the blower fan. 3. Rev engine with loads on. 4. Idle engine and turn off loads. 5. The Charging System decision is displayed at the end of the procedure. No.
3 LOW OUTPUT 4 HIGH OUTPUT 5 EXCESSIVE RIPPLE Alternator not providing sufficient to power the system's electrical loads and charge the battery. Check the belts to ensure the alternator is rotating with the engine running. Replace broken or slipping belts and retest. Check the connections from the alternator to the battery. If the connection is loose or heavily corroded, clean or reparable the cable and retest. Alternator voltage output exceeds the normal limits.
3. To print the test results, just press the Print button on the unit. 4. Select Yes to type in the plate number so the test ticket could show test result with the exact plate number. Or select No to quit typing plate number. 5. Follow the on-screen prompt to input the plate number. 6. After entering the plate number, the following prompt shows. 19 BT705 Battery Analyzer User’s Guide - English Version_V1.
7. Press the Power button on the printer to turn it on. It will print out the test result automatically. 5 Language Language menu lets choose system language. The test is set to English menu by default. To change the language setting: 1. Scroll with the UP or DOWN button to highlight Language from Main Menu and press the ENTER key. 2. Use the UP or DOWN button to select the language you need and press the ENTER key to confirm and return. Or press BACK button to return without saving.
2. Select SEARCH from the menu to match new Bluetooth printer or select DEVICE to connect with the existing Bluetooth printer. 7 Version Info Version Info menu lets you view software information of the tester. To check the software version: 1. Select Version Info from the main menu. The follow screen shows the version of the tester. 21 BT705 Battery Analyzer User’s Guide - English Version_V1.