Trademarks FOXWELL is trademark of Shenzhen Foxwell Technology Co., Ltd. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information ©2022 Shenzhen Foxwell Technology Co., Ltd. All rights reserved. Disclaimer The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice. Visit our website at www.foxwelltech.
One-Year Limited Warranty Subject to the conditions of this limited warranty, Shenzhen Foxwell Technology Co., Ltd (“FOXWELL”) warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one (1) year.
b) The customer shall include a return address, daytime phone number and/or fax number, complete description of the problem and original invoice specifying date of purchase and serial number. c) The customer will be billed for any parts or labor charges not covered by this limited warranty. d) FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product.
consequential damages, so certain of the above limitations or exclusions may not apply to you (the Consumer). This limited warranty gives the Consumer specific legal rights and the Consumer may also have other rights which vary from state to state. 4 Automotive Diagnostic SystemI70BT User's Manual V1.
Safety Information For your own safety and the safety of others, and to prevent damage to the equipment and vehicles, read this manual thoroughly before operating your tool. The safety messages presented below and throughout this user’s manual are reminders to the operator to exercise extreme care when using this device. Always refer to and follow safety messages and test procedures provided by vehicle manufacturer. Read, understand and follow all safety messages and instructions in this manual.
such as in below-ground pits, confined areas, or areas that are less than 18 inches (45 cm) above the floor. ● Do not smoke, strike a match, or cause a spark near the vehicle while testing and keep all sparks, heated items and open flames away from the battery and fuel / fuel vapors as they are highly flammable. ● Keep a dry chemical fire extinguisher suitable for gasoline, chemical and electrical fires in work area.
Table of Contents ONE-YEAR LIMITED WARRANTY ..................................................................................................... 2 SAFETY INFORMATION ..................................................................................................................... 5 1 USING THIS MANUAL ..................................................................................................................... 9 1.1 BOLD TEXT .......................................................................
6.12KEY PROGRAMMING/IMMOBILIZER .............................................................................................. 42 7 DATA MANAGER ........................................................................................................................... 42 7.1 IMAGE ....................................................................................................................................... 42 7.2 PDF REPORT ............................................................................
1 Using This Manual We provide tool usage instructions in this manual. Below are the conventions we used in the manual. 1.1 Bold Text Bold text is used to highlight selectable items such as buttons and menu options. Example: Select Diagnostic from the Home screen of the NT809BT application. 1.2 Symbols and Icons 1.2.1 Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot ●. Example: When VIN hotkey is selected, a menu that lists all available options displays.
IMPORTANT indicates a situation, which if not avoided, may result in damage to the test equipment or vehicle. Example: IMPORTANT Do not soak scanner as water might find its way into the scanner. 2 Introduction The brand new Android scan tool NT809BT inherits the same Foxwell advantages in car fault diagnostic tech, such as multi manufacturer coverage, service functions and accurate test data, making it the perfect tool for busy garages or workshops, who need the latest technology at unbeatable value. 2.
Figure 2-2 Top View 3 Power Switch - turns on the scanner, goes to sleep mode or wake up the scanner from sleep mode, press and hold for 3 seconds for emergency shutdown. 4 USB Type-C Port - connects to wall plug to charge the scanner and can be used for data transfer. USB Port - provides a USB connection for the external storage devices, oscilloscope or video scope etc. IMPORTANT Do not use solvents such as alcohol to clean display. Use a mild nonabrasive detergent and a soft cotton cloth. 5 2.
Figure 2-3 Front View of VCI dongle 1 Running Light– flashes during normal operation, and stays on or off when abnormal. 2 Communication Light – is always on when VCI connect to device via bluetooth or USB, and flashes when sending data. 3Power Light - turns to red when powered on. 2.3 Accessories This section lists the accessories that go with the scanner. If you find any of the following items missing from your package, contact your local dealer for assistance.
Table 2-1 Accessories 2.4 Technical Specifications Item Description Protocols ISO9141-2, ISO14230-2, ISO15765-4, K/L lines, Double K Line SAE-J1850 VPW,SAE-J1850PWM,CAN ISO 11898, High-speed, Middle-speed, Lows-peed and Single wire CAN, KW81, KW82, GM UART, UART Echo Byte Protocol, Honda Diag-H Protocol, TP2.0, TP1.
3 Getting Started This section describes how to power on/down the scanner, provides brief introductions of applications loaded on the scanner and display screen layout of the scan tool. 3.1 Powering up the Scanner Before using the NT809BT applications (including updating the scanner), please make sure to provide power to the scanner. The unit operates on any of the following sources: ● Internal Battery Pack ● External Power Supply 3.1.
Figure 3-1 Sample Home Screen 3.3.1 Application Menu Figure 3-2 Sample Application Screen This section briefly introduces the applications that are preloaded into the scanner: ●Diagnostic- leads to test screens for diagnostic trouble code information, freeze frame, live data and ECU information. ●Maintenance - leads to screens for common used special functions like Oil light reset, EPB, BRT, and DPF etc. ●Update - leads to screens for Foxwell ID registration and updating the scanner.
● ● Firmware Update –VCI firmware update. VCI Manager– VCI manage (VCI binding,unbinding,rescanvehicle software). 3.3.2 Diagnostic Menu Touch Diagnostic at the NT809BT application menu, and the Diagnostic menu will display. The operations of the buttons of Diagnostic menu are described in the below table. Diagnostic Menu Screen No. Name Figure 3-3 Sample Description 1 Back Back to the previous screen. 2 Home Back to the Application Menu.
prompts and make a series of choices. Each selection you make advances you to the next screen. Exact procedures may vary somewhat by vehicle. It typically identifies a vehicle by any of the following means: ● VIN Reading ● Manual Selection NOTE Not all identification options listed above are applicable to all vehicles. Available options may vary by vehicle manufacturer. 4.1Vehicle Connection To establish communication with NT809BT: 1. Power up the tablet. 2.
Figure 4-2 Sample VCI Manager Screen 4. Check if the button at the toolbar turns to green. If yes, it means it’s ready to start diagnosis. Figure 4-3 Sample VCI Indicator Status Screen NOTE If the VCI Indicator isn’t green , it indicates that the signal strength of the transmitter is too weak to be detected. In this case, try to get closer to the device, or check the connection of VCI dongle, and remove all possible objects that cause signal interference 4.
Figure 4-4 Sample VIN Hotkey Screen 4.2.1 Automatic Read AutomaticRead allows to identify a vehicle by automatically reading the vehicle identification number (VIN). To identify a vehicle by Automatic Read: 1. Select Diagnosticfrom home screen ofthe NT809BT application. 2. Click VINand choose Automatic Read from the option list. 3. When the scan tool builds connection with the vehicle, the VIN number displays.
Figure 4-6 Sample Automatic Read Screen 4.2.2 Manual Entry Manual Entry allows to identify a vehicle by inputting VIN manually. . To identify a vehicle by Manual Entry: 1. Select Diagnosticfrom home screen ofthe NT809BT application. 2. Click VINand choose Manual Entry from the option list. 3. Press Keyboard button to input a valid VIN code and press OK to continue. Figure 4-7 SampleManual Entry Screen 4.
Figure 4-8 Sample Vehicle Entry Screen 4.3.1 Smart VIN Smart VINallows to identify a vehicle by automatically reading thevehicle identification number (VIN). To identify a vehicle by Smart VIN: 1. Select Diagnosticfrom home screen ofthe NT809BT application. 2. A screen with vehicle manufacturers displays. Select the area where thevehicle manufacturer from. A menu of all vehicle manufacturers displays. Or tap the Search box to search the car you are to test. Figure 4-9 Sample Vehicle Selection Screen 3.
Figure 4-10 Sample Smart VIN Screen 4. After the scan tool builds connection to the vehicle, the VIN number displays. If the Vehicle Specification or VIN code is correct, press the OK to continue. If incorrect, please enter a valid VIN number manually. 4.3.2 Manual Vehicle Selection Manual Selection identifies a vehicle by making several selections according to certain VIN characters, such as model year, and engine type. To identify a vehicle by manual vehicle selection: 1.
4.4Vehicle History Vehicle History keeps records of tested vehicles and allows restarting the diagnosis of a vehicle without the need to do vehicle identification again. To identify a vehicle by Vehicle History: 1. Select Diagnosticfrom home screen ofthe NT809BT application. 2. Select History button at the top of the diagnostic page and the diagnostic records will display. Figure 4-12 Sample History Record Screen 3. Choose the vehicle model you want to test from the list. 4.
5.1 Vehicle Identification When you completed the identification of vehicle, you have to identify the control modules installed in the vehicle. There are two ways to identify the controllers installed in a car: ● Quick Scan ● Control Modules Figure 5-1 Sample Diagnosis Screen NOTE Not all identify options listed above are applicable to all vehicles. Available options may vary by the year, model, and make of the test vehicle. 5.1.
Figure 5-2 Sample Quick Scan Screen 3. At the end of successful automatic controller scan, a menu with a list of DTC displays and click button to the right to view DTC descriptions. Figure 5-3 Sample Quick Scan Complete Screen 4. Press Reportto create an overview of installed control units and their system status, or press Save to save the report. Press Erase to clear the information. Figure 5-4 Sample DTC Save Screen 25 Automotive Diagnostic SystemI70BT User's Manual V1.
Figure 5-5 Sample Report Screen Figure 5-6 Sample Erase Screen 5. When running auto scanning, you can press Pause and select the system you would like to test. When the scanner has established connection with the vehicle, the Function Menu displays. Figure 5-7 Sample Function Menu Screen 5.1.2 Control Modules Control Modules displays all controllers available of the vehicle manufacturer. The controllers listed on the menu do not mean that they are installed on the vehicle.
To select a system to test: 1. Press Control Modules from the menu and a controller menu displays. Figure 5-8 Sample Control Modules Screen 2. Select a system to test. When the scanner has established connection with the vehicle, the Function Menu displays. Figure 5-9 Sample Function Menu Screen 5.2 Diagnostic Operations After a system is selected and the scanner establishes communication with the vehicle, the Function Menu displays.
5.2.1 Read Codes Read Codes menu lets you read trouble codes found in the control unit. There are 4 types of code status: ● Present/Permanent/Current ● Pending ● History Present/Permanent/Current codes stored in a control module are used to help identify the cause of a trouble or troubles with a vehicle. These codes have occurred a specific number of times and indicate a problem that requires repair. Pending codes are also referred to as maturing codes that indicate intermittent faults.
recorded by the on-board computer at the time of the DTC set. It is a good function to help determine what caused the fault. Figure 5-11 Sample Freeze Frame Screen ●Help - select one fault code from the code list and click Help button on the screen. The screen will display the detailed descriptions about the fault code and repair guide. Figure 5-12 Sample DTC Help Screen 2. Slide up and down to view additional information when necessary. 3. Press Save to store DTC information.
● Clear Codes does not fix the problem that caused the fault! DTCs should only be erased after correcting the condition(s) that caused them. To clear codes: 1. Press Clear Codes from Select Diagnostic Function menu. Figure 5-13 Sample Function Menu Screen 2. Follow the on-screen instructions and answer questions about the vehicle being tested to complete the procedure. 3. Check the codes again. If any codes remain, repeat the Clear Codes steps. 5.2.
To view all live PID data: 1. Press Select ALL for select all live PID data and press Deselect ALL to deselect all items. Figure 5-15 Sample Function Menu Screen 2. Press OK to complete the selection and all readings will be displayed in text format by default. Figure 5-16 Sample Live Data Selection Screen Figure 5-17 Sample Live DataScreen 31 Automotive Diagnostic SystemI70BT User's Manual V1.
Name Description Help To provide help information of a PID To Top To move a data line to the top of Data List screen History To view the previous live data records or test reports Record To make record of live data Save To save live data of current frame Pause To stop recording live data Table 5-1 Live Data Screen Button Screen ● Learn Mode:gives you the ability to learn good live sensor data values during idle, KEKO, acceleration, deceleration, part load and heavy load on each vehicle comes
Figure 5-19 Sample Live Data Screen 3. Swipe the screen up and down to view additional information when necessary. 4. To move a data line to the top of Data List screen, just tap the line to select and then press the button To Top. To view data records or test reports, and press the button History. To make records of live data, just tab the button Record, and press Pauseto stop recording at any time. To save the data, tap the Save icon. 5.
Figure 5-22 Sample Merge Graph Screen 5.2.3.2 Custom List Custom List menu lets you to minimize the number of PIDs on the data list and focus on any suspicious or symptom-specific data parameters. To create a custom data list: 1. Press Custom List from the menu to display all available parameters from the selected control module. 2. The custom data stream selection screen displays. Tap the lines you wish to select.
Figure 5-24 Sample Live Data Screen 5.2.3.3 Record data Data Record is for recording the running data of the current control module. To Record Data 1. Press Record button to record all selected live data, then it will show the record time and frames. Figure 5-25 Sample Live Data Record Screen 2. Press Stop button to create a record, then press OK to save the record into Data Playback of Data Manager. 35 Automotive Diagnostic SystemI70BT User's Manual V1.
Figure 5-26 Sample To Stop Live Data Record Screen 5.2.4 ECU Information ECU Information screen displays the identification data of the control module under test, such as the control module identification string and the control module coding. To read ECU information: 1. Press ECU Information from Select Diagnostic Function menu. Figure 5-27 Sample Function Menu Screen 2. A screen with detailed information of the selected control module displays. Figure 5-28 Sample ECU Information Screen 3.
Figure 5-29 Sample ECU Information save Screen 6 Maintenance This section gives brief instructions of the most commonly required service and maintenance operations. Typical service operation screens are a series of menu driven executive commands. Follow on-screen instructions to complete the operation.
●Oil Reset with One Button - applicable to GM models only. It offers quick and simple oil service reset with the click of one button. ● Manual Reset - almost all Asian vehicles and most American and European vehicles have mechanical oil service indicator reset. The service tool does not have to communicate with the vehicle being tested, but guides you to complete the service manually by providing step-by-step on-screen instructions.
●Perform activation/service work on Volvo PBM vehicles – allows to perform installation check, applying parking brake, releasing parking brake, activating service mode and exiting service mode. ●Reset memory on Toyota EPB vehicles – allows to clear the learned memory of the EPB ECU. ●Perform brake cable replacement and electric parking brake replacement – allows to fit in or remove the brake cable safely, adjust brake cable’s tension and calibrate the electric parking brake replacement.
3. Boost the device and select BRT; it will display all the vehicle makes available. Choose your vehicle make and follow the scanner instruction to start. ●Sensor calibration on Honda EPB vehicles - allows to program the current output value of each sensor into the electric parking brake unit. ●Perform BRT on Citroen/Peugeot cars - make several selections to confirm your car model, and then complete the battery replacement following on-screen instructions.
6.7Continuous Variable Transmission (CVT) This function is used to reset the compensation code and initialize the ECT after a solenoid valve or valve body assembly has been replaced. 6.8Gear Learning The crankshaft position sensor learns crankshaft tooth machining tolerance and save to the computer to more accurately diagnose engine misfires. If tooth learning is not performed for a car equipped with Delphi engine, the MIL turns on after the engine is started.
6.12Key Programming/Immobilizer The transponder key is an aftermarket option that can be programmed for a number of vehicles. Also known as a chip key or ignition key, this key offers a level of convenience and security for your car. If your car is equipped with a chip key system, only a programmed key can turn on the ignition in your vehicle. 7 Data Manager Data Manager menu let you reviewstored screenshots and test reports, playback recorded live data and other saved files.
Figure 7-2 Sample Screenshots type 7.1.1 How to Save an Image Totake a screenshot: 1. If want to save data of current screen,press screenshot. at the title bar to take a Figure 7-3 Sample Screenshot Screen 2. Add a description of the image, and press the OK to save，cancel button to give up. Figure 7-4 Sample Screenshot Screen 43 Automotive Diagnostic SystemI70BT User's Manual V1.
7.1.2 Review Image Toreview the screenshots: 1. Press Data Manager from home screen of NT809BT diagnostic application. 2. Press Image and all available pictures will be displayed. 3. Press Diagnostic Screenshot for application menu screenshotor Press System Screenshot for system menu screenshot, then all available pictures will be displayed. Figure 7-5 Sample Browse Picture Screen 4. Press any available picture for review. 5. To delete a picture, tap button Delete and answer OK to delete.
Figure 7-7 Sample All Pictures Edit Screen 7.2 PDF Report PDF option leads to screens for review of the vehicle test reports. You just need to press the PDF icon on the test screen, add a description and press OK button to save. 7.2.1 How to Create a PDF Report To create a PDF report: 1. Press Data Manager from home screen of NT809BT diagnostic application. 2. Press Report from Data Manager. 3. Press any reports saved. Figure 7-8 Sample of Reports Screen 4. Press Save to save changes.
Figure 7-9 Sample of Report edit Screen 5. If press PDF, the PDF review screen will be displayed. Press Print to print the report or press Email to share the report. Figure 7-10 Sample of Report edit Screen 7.2.2 Review PDF Report Toreview the PDF reports: 1. Press Data Manager from home screen of NT809BT diagnostic application. 2. Press PDF and all available PDF files will be displayed. Figure 7-11 Sample Browse PDF Screen 46 Automotive Diagnostic SystemI70BT User's Manual V1.
3. Long press the screen to edit all PDF files like Rename or Delete the files. Figure 7-12 Sample Edit PDF Screen 7.3 DataPlayback The Data Playback option leads to screens for review of recorded live data. Playing back a recording is just like using the scan tool on a live vehicle. It let you review live data in text, graph and graph merging formats. Playback speed and direction (forward or reverse) can also be controlled. To review recorded live data: 1.
Figure 7-14 Sample Data Playback Selections Screen 4. To view parameter graphs, press the Graph tab. And to merge the graphs, press the tab Merge Graphor press the tab Multi Graph to view multiple plots. Figure 7-15 Sample Graph Screen 5. To move forward or reverse back of the playing, just drag the progress bar forward or reverse. Press the button to stop. 6. Long press the record to Rename or Delete the records.
8.My Account This section introduces user account registration, login, device activation and other information. When My Accountapplication is selected, a menu with availableoptions displays. My AccountMenu options typically include: ● My Account ● My Products ● Feedback and Suggestions Figure 8-1 Sample My Account Screen 8.
Figure 8-2 Sample Update Client Main Screen 2. Enter the User Name(use one of your existing mail addresses as user name), and press Send Code button for get a verification code, Foxwell will send a 4-digit verification code to the email you just entered. Figure 8-3 Sample ID Registration Screen 3. Get the security code in your mailbox, input the code as verification code. Then create a password and click Free Registration to complete. Figure 8-4 Sample ID Registration Screen 4.
Figure 8-5 Sample Registration Done Screen 5. The serial number will show after registration. Click Submit to activate the product or press to back. Figure 8-6 Sample Production Activation Screen 8.1.2 Register through Website To register through our website: 1. Visit Foxwell official website www.foxwelltech.us and press Registericon, or go to the registration page by selecting Support from home page and then click Register.
Figure 8-8 Sample Website Register Screen 2. Enter one of your email addresses as your user ID and click the Send Code button. We will send a 4-digit verification code to the email you just entered.Find the security code in your mailbox, input the code, create a password and click Free Registration to complete. Figure 8-9 Sample Create Account Screen 3. Sign in to the Member Center, click New Registration, input the right serial number and click Submit to activate the product.
Figure 8-10 Sample Product RegisterScreen 8.2 Sign in Press My Account or Update from home screen of NT809BT diagnostic application, the user login page will show, enter your FOXWELL ID and password, and press Sign in button to sign in. Figure 8-11 Sample Sign inScreen 8.2.1 Product activate If you are logging in for the first time, it will prompt and guide you to activate the current device while sign in successfully. To activate product 1. Press OK button to activate product and press Cancel to back.
Figure 8-12 Sample Product Activation Screen 2.Click Submit to continue the activation and press to give up activation. Figure 8-13 Sample Product Activation SubmitScreen 3. “Product is activated successfully” message will appear if activate successfully. Figure 8-14 Sample activate successScreen 54 Automotive Diagnostic SystemI70BT User's Manual V1.
8.3 My Account My Account option allows you to check and modify or complete your account information including user name, e-mail, telephone, address and so on. Figure 8-15 Sample My Account Screen 8.4 My Products This option let you activate a new product and manageactivated products including serial number and expiration date. Figure 8-16 My Product Screen 8.5 Feedback and suggestions This option allows you to log on your e-mail and send feedback and suggestions about Foxwell products.
1. Press My Account from home screen of the NT809BT diagnostic application. 2. Press Feedback and Suggestions option to show Feedback page, there are two options--Diagnosis Feedback and General Feedback. Figure 8-17 Sample feedback record Screen 3. Select Diagnosis Feedback or General Feedback for creating a feedback. Select the type oferror and some necessary content and problem description or attachments. Press Savebutton to save the feedback. Or press Email button to send if you have an email account.
Figure 8-19 Sample Email Select Screen 9 Update The scanner can be updated to keep you stay current with the latest development of diagnosis. This section illustrates how to register and update your scan tool. You can register both on Foxwell website or by the built-in update client. NOTE Before registration and updating, please make sure your network works correctly and the tablet is fully charged or connect to external power supply. 9.
2. Select Automatic Update, then set automatic update notice enable. 9.2 Manual Update To update the diagnostic application: 1. Press Updateof NT809BT diagnostic application, and the update client starts up automatically. 2. The available updates display. Click the check box(s) in front of the software you wish to update and then click the Update button to download. 3. When all the items are updated, an “Update Done” message displays.
2. After clicking Unbind a VCI dongle, it will display whether to unbind the current VCI. When clicking OK, it will execute unbind, rebind, and refresh the vehicle. Figure 10-1 Sample Unbind a VCI dongle Figure 10-2Sample Unbinding Confirmation Prompt Figure 10-3Sample Unbinding Current VCI 59 Automotive Diagnostic SystemI70BT User's Manual V1.
Figure 10-4 Sample Bind New VCI Successfully Figure 10-5 Sample Rescan Vehicle Software 11 Firmware Update This application allows you to update the firmware of i53BT. To update the firmware: 1. Click the Update application on the i53BT home screen. 2. Check and download the firmware package. 3. After the download is completed, it will automatically jump to the Firmware Update function module. 4. Check the battery level to ensure that the battery level should be greater than 20%. 5.
Figure 11-1 Sample Firmware Update Screen 6. “VCI firmware successfully message” will appear if update successfully. Figure 11-2 Sample Firmware Update Successfully Screen NOTE If there is a firmware update available, the update file will be downloaded and saved automatically when you try to update the diagnostic software. And you will be prompted to upgrade the firmware. 12 Settings This section illustrates how to program the scanner to meet your specific needs.
● General ● Uninstall Vehicle Software ● Clear app data ● Print Settings ● About 12.1 Units Selecting Unit opens a dialog box that allows you to choose between Imperial customary or metric units of measure. To change the unit setup: 1. Press Settings from home screen of the NT809BT diagnostic application. 2. Press Unit and available unit system display. 3. Select a unit system. 12.2 Language SelectLanguage opens a screen that allows you to choose system language. To configure system language: 1.
12.5 Remote control This option allows you toselect a tool of remote control. There are two remote tools available TeamViewer QuickSupport or AnyDesk. To change remote control 1. Press Settings from home screen of the NT809BT diagnostic application,then select Remote control. 2. Select your preferred tool. 12.6Automatic Update This option allows you to enable/disable automatic update notice.
Figure 12-1 Sample Uninstall Vehicle Software Screen 4. PressCancel to quit or and pressOK to uninstall. Figure 12-2 Sample Uninstall Vehicle Software Screen 12.10Clear app data Generally, after the application running for a period of time, some cache data will be generated. As time goes by, the cached data will become larger and larger, which will affect the operation of the device. This option allow you to clear the cache data of the app. 12.
Figure 12-3 Sample Print Settings Screen 3. Tap Print Plugin Managerand turn on the Mopria Print Service, then NT809BT will search for available printers automatically. Figure 12-4 Sample Print Service Manager Screen 4. Select Mopria Print Service. Press for return. Figure 12-5 Sample Setting of Print Service Manager Screen 5. Choose the right printer. Press for return. 65 Automotive Diagnostic SystemI70BT User's Manual V1.
Figure 12-6 Sample of Printer Screen 6. Select a available printer, then press PRINT TEST PAGE button at the right-bottom. Press for return. Figure 12-7 Sample of Printer test 7. Choose the file or report you want to print and press the print icon . Click on the red marked part to select an available printer. Click the blue marked part to make more settings for the printer, such as paper size, number of copies, etc.
1. Please make sure the printer and the NT809BT in the same Wi-Fi or Network when printing. 2. If Mopria Print Service driver can’t workable for your printer, please download the driver to work for your printer on Print Service Manager. 12.12About Selecting Aboutoption opens a screen that shows information about the NT809BT, such as serial number, hardware and software version and etc. To view information of your scan tool: 1. Press About from home screen of the NT809BT diagnostic application. 2.
Figure 13-1 Sample QuickSupport Screen 2. Send your ID to us to let our team to take control your tablet. FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
