Trademarks FOXWELL is trademark of Shenzhen Foxwell Technology Co., Ltd. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information ©2020 Shenzhen Foxwell Technology Co., Ltd. All rights reserved. Disclaimer The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice. Visit our website at www.foxwelltech.
Two-Year Limited Warranty Subject to the conditions of this limited warranty, Shenzhen Foxwell Technology Co., Ltd (“FOXWELL”) warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of two (2) year.
b) The customer shall include a return address, daytime phone number and/or fax number, complete description of the problem and original invoice specifying date of purchase and serial number. c) The customer will be billed for any parts or labor charges not covered by this limited warranty. d) FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product.
consequential damages, so certain of the above limitations or exclusions may not apply to you (the Consumer). This limited warranty gives the Consumer specific legal rights and the Consumer may also have other rights which vary from state to state. 4 Premier Diagnostic Platform II i80 Max User's Manual V1.
Safety Information For your own safety and the safety of others, and to prevent damage to the equipment and vehicles, read this manual thoroughly before operating your tool. The safety messages presented below and throughout this user’s manual are reminders to the operator to exercise extreme care when using this device. Always refer to and follow safety messages and test procedures provided by vehicle manufacturer. Read, understand and follow all safety messages and instructions in this manual.
● Fuel, oil vapors, hot steam, hot toxic exhaust gases, acid, refrigerant and other debris produced by a malfunction engine can cause serious injury or death. Do not use the tool in areas where explosive vapor may collect, such as in below-ground pits, confined areas, or areas that are less than 18 inches (45 cm) above the floor.
Table of Contents Automotive Diagnostic Tool i80Max TWO-YEAR LIMITED WARRANTY.....................................................................................................................2 SAFETY INFORMATION........................................................................................................................................5 SAFETY MESSAGE CONVENTIONS USED....................................................................................................
4.1.1 Automatic Read..................................................................................................................................25 4.1.2 Scan VIN..............................................................................................................................................27 4.1.2.1 Scan VIN Plate...........................................................................................................................27 4.1.2.2 Scan Barcode/QR Code of VIN.................
7.1 IMAGE.............................................................................................................................................................59 7.1.1 How to Save an Image......................................................................................................................60 7.1.2 Review Image..................................................................................................................................... 60 7.2 REPORTS..............................
1 Using This Manual We provide tool usage instructions in this manual. Below are the conventions we used in the manual. 1.1 Bold Text Bold text is used to highlight selectable items such as buttons and menu options. Example: Select Diagnostic from home screen of the i80 Max application. 1.2 Symbols and Icons 1.2.1 Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot ●. Example: When VIN hotkey is selected, a menu that lists all available options displays.
NOTE Test results do not necessarily indicate a faulty component or system. Important IMPORTANT indicates a situation, which if not avoided, may result in damage to the test equipment or vehicle. Example: IMPORTANT Do not soak scanner as water might find its way into the scanner. 2 Introduction The latest Android tablet scanner i80 Max delivers faster and smarter diagnosis for workshops and technicians.
Figure 2-1Front View 1 10’’ LED IPS Capacitive Touch Screen - shows menus, test results and operation tips. 2 Power Indicator - indicates the power status of the scanner. Figure 2-2 Back View 3 Rear-Facing Camera - takes pictures of VIN number, faulty parts and plates and shoots test videos. 12 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 2-3 Top View 4 VOL + / VOL - press to adjust the volume. 5 Power Port - connects to wall plug to charge the scanner. 6 Ethernet Port - connects with Ethernet cable. 7 HDMI (high-definition multimedia interface) Port - outputs display of the scanner for demonstration and training. 8 USB Port - provides USB connection with VCI dongle, oscilloscope, video scope and other external storage devices. 9 USB Type-C Port - be used to transfer data. 10 SIM Card Port - inserts SIM card.
1 2 3 4 Figure 2-5 Front View of VCI dongle 1 Error Light - illuminates constantly when serious hardware failure occurs. 2 USB Light - turns green when the VCI dongle is properly connected and communicating with the i80 Max tablet via USB cable. 3 Bluetooth Light - turns green when the VCI dongle is properly connected with the i80 Max tablet via Bluetooth communication. 4 Power Light - turns to green when powered on.
6 Figure 2-7 Bottom View of VCI 6 USB Port - provides USB connection between the VCI dongle and i80 Max tablet. 2.3 Accessories This section lists the accessories that go with the scanner. If you find any of the following items missing from your package, contact your local dealer for assistance. 15 Premier Diagnostic Platform II i80 Max User's Manual V1.
Table 2-1 Accessories 2.4 Technical Specifications Item Description Touch Screen 10.1’’ diagonal, daylight readable color LCD screen, 1920*1200 pixel Operation Android 16 Premier Diagnostic Platform II i80 Max User's Manual V1.
System Processor RK3288 (ARM Cortex, a17x4, 1.8GHz) Memory 2GB LPDDR3 SSD Hard drive 64GB System Type Android 8.1 Communication interface Built-in WIFI 802.11 b/g Wireless LAN USB2.0 OTG/standard USB 2.0 HOST Bluetooth 4.
3.1.2 External Power Supply The tablet can also be powered from a wall socket using the DC charge adapter. The tablet charges its internal battery pack through charge cable. 3.2 Shutting Down the Scanner All vehicle communication must be terminated before shutting down the scanner. Exit the Diagnostic application before powering down. Figure 3-1 Power-off Prompt Screen To shut down the scanner: 1. Press and hold the Power button of the i80 Max for 5 seconds. 2.
Figure 3-2 Sample Bluetooth Communication Screen Figure 3-3 Sample USB Communication Screen Please refer to Chapter 3.3.1.1about the details of how to connect via Bluetooth and Chapter 3.3.1.2 about the details of how to connect via USB cable. 3. Check the VCI Indicator status at the toolbar. If the button turns to green, the i80 Max is ready to start vehicle diagnosis. 3.3.
To build Bluetooth connection: 1. Power up the tablet. 2. Go to VCI Manager and then Bluetooth. Click Connect and the VCI dongle will connect to the tablet automatically. Figure 3-4 Sample VCI Manager Screen Figure 3-5 Sample Bluetooth Connection Screen 3. Check if the button at the toolbar turns to green. If yes, it means it’s ready to start diagnosis. Figure 3-6 Sample VCI Indicator Status Screen 20 Premier Diagnostic Platform II i80 Max User's Manual V1.
NOTE If the VCI Indicator isn’t green, it indicates that the signal strength of the transmitter is too weak to be detected. In this case, try to get closer to the device, or check the connection of VCI dongle, and remove all possible objects that cause signal interference 3.3.1.2 USB Communication The USB connection is a simple and quick way to establish communication between the tablet and the VCI dongle.
3.4.1 Application Menu Figure 3-8 Sample Application Screen This section briefly introduces the applications that are preloaded into the scanner: ● Diagnostic - leads to test screens for diagnostic trouble code information, live data, active tests, coding and etc. ● Update - leads to screens for Foxwell ID registration and updating the scanner. ● Settings - leads to screens for adjusting default settings to meet your own preference and view information about the scanner.
Back Back to the previous screen. Home Returns to Home screen of Android System. Multitask Allows for browsing, switching and closing active applications. Camera Takes a photo or picture. Browser Opens the built-in browser. Screenshot VCI Indicator Diagnostic Maintenance Captures screens. Shortcut for VCI Manager menu from any screen of the tablet; also it is the indicator of Bluetooth/USB connection status. Shortcut for Diagnostic menu from any screen of the tablet.
3.4.3 Diagnostic Menu Touch Diagnostic at the i80 Max application menu, and the Diagnostic menu will display. The operations of the buttons on Diagnostic menu are described in the below table. Figure 3-9 Sample Diagnostic Menu Screen No. Name 1 Home 2 VIN 3 History 4 Area 5 Search Description Back to the Application Menu. Shortcut for VIN reading menu, which typically includes Automatic Read, Scan VIN and Manual Entry. Displays the tested vehicle records.
prompts and make a series of choices. Each selection you make advances you to the next screen. Exact procedures may vary somewhat by vehicle. It typically identifies a vehicle by any of the following means: ● VIN Reading ● Manual Selection ● History Records NOTE Not all identification options listed above are applicable to all vehicles. Available options may vary by vehicle manufacturer. 4.
Figure 4-2 Sample Automatic Read Screen 3. When the scan tool builds connection with the vehicle, the VIN number displays. If the Vehicle Specification or VIN code is correct, press the OK to continue. Figure 4-3 Sample Automatic Read Screen 4. If it takes too long to get the VIN code, press Cancel to stop and input the VIN manually. Or if failed to identify the VIN, please input the VIN manually or click Cancel to quit. 26 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 4-4 Sample Manual Entry Screen 4.1.2 Scan VIN Scan VIN allows identifying a vehicle by scanning the VIN plate of the vehicle, barcode, QR code or photo recognition. 4.1.2.1 Scan VIN Plate To identify a vehicle by Scan VIN Plate: 1. Select Diagnostic from home screen of the i80 Max application. 2. Click VIN button and choose Scan VIN from the option list. 3. Find the VIN plate of your car, and put the VIN number into the scanning box. The VIN number displays with a successful scan.
Figure 4-7 Sample Modify VIN Screen 4. If failed, please click Close to quit and input the VIN manually. 4.1.2.2 Scan Barcode/QR Code of VIN To identify a vehicle by Scan QR Code: 1. Select Diagnostic from home screen of the i80 Max application. 2. Click VIN button, choose Scan VIN from the option list and enable Scan QR Code at the lower left part of the screen. Figure 4-8 Sample Scan QR Code Screen 3. Find the VIN QR code or bar code of your car, and put the code into the scanning box.
Figure 4-9 Sample Scan QR Code Screen Figure 4-10 Sample VIN Confirmation Screen 4. If failed, please click Close to quit and input the VIN manually. 4.1.2.3 Photo Recognition To identify a vehicle by Photo Recognition: 1. Select Diagnostic from home screen of the i80 Max application. 2. Click VIN button and choose Scan VIN from the option list. 3. Find the VIN plate, QR code or barcode of your car, and put the content number into the scanning box.
Figure 4-11 Sample Photo Recognition Screen Figure 4-12 Sample VIN Confirmation Screen Figure 4-13 Sample Modify VIN Screen 4. If failed, please click Close to quit and input the VIN manually. 4.1.3 Manual Entry Manual Entry allows to identify a vehicle by inputting VIN manually. To identify a vehicle by Manual Entry: 30 Premier Diagnostic Platform II i80 Max User's Manual V1.
1. Select Diagnostic from home screen of the i80 Max application. 2. Click VIN and choose Manual Entry from the option list. 3. Press Keyboard button to input a valid VIN code and press OK to continue. Figure 4-14 Sample Manual Entry Screen 4.2 Manual Selection Select vehicle brand you are to test, and two ways of getting to the diagnostic operations are available. ● Smart VIN ● Manual Selection Figure 4-15 Sample Vehicle Entry Screen Name Home Button Description Back to the Application Menu.
Settings Data Logging Print Screenshot A shortcut for Settings menu. Records the communication data between the scan tool and the vehicle to help with troubleshooting of diagnostic failures. Print the test data and report. Takes screenshot of test data or report and save them for later analysis. Table 4-1Title Bar 4.2.1 Smart VIN Smart VIN allows to identify a vehicle by automatically reading the vehicle identification number (VIN). To identify a vehicle by Smart VIN: 1.
Figure 4-17 Sample Smart VIN Screen 4. After the scan tool builds connection to the vehicle, the VIN number displays. If the Vehicle Specification or VIN code is correct, press the OK to continue. If incorrect, please enter a valid VIN number manually. 4.2.2 Manual Vehicle Selection Manual Selection identifies a vehicle by making several selections according to certain VIN characters, such as model year, and engine type. To identify a vehicle by manual vehicle selection: 1.
4.3 Vehicle History Vehicle History keeps records of tested vehicles and allows restarting the diagnosis of a vehicle without the need to do vehicle identification again. To identify a vehicle by Vehicle History: 1. Select Diagnostic from home screen of the i80 Max application. 2. Select History button at the top of the diagnostic page and the diagnostic records will display. Figure 4-19 Sample History Record Screen 3. Choose the vehicle model you want to test from the list. 4.
5 Diagnosis This section illustrates how to use the scanner to read and clear diagnostic trouble codes, view live data readings and ECU information on controllers installed, perform special functions such as actuation and coding, and perform vehicle services and maintenance on Asia, European and USA vehicle brands. When you have completed the identification of vehicle, the main menu displays. Menu options typically include: ● Diagnosis ● Special Functions Figure 5-1 Sample Main Menu Screen 5.
Figure 5-2 Sample Diagnosis Screen 5.1.1 Quick Scan Quick Scan performs an automatic system test to determine which control modules are installed on the vehicle and provides diagnostic trouble codes (DTCs) overview. Depending on the number of control modules, it may take a few minutes to complete the test. To perform an automatic system scan: 1. Press Quick Scan option to start. 2. To pause the scan, press the Pause button on the screen. Figure 5-3 Sample Quick Scan Screen 3.
Figure 5-4 Sample Quick Scan Complete Screen 4. Press Report to create an overview of installed control units and their system status, or press Save to save the report. Press Erase to clear the information. Figure 5-5 Sample DTC Save Screen Figure 5-6 Sample Report Screen 37 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 5- 7 Sample Erase Screen 5. When running auto scanning, you can press Pause and select the system you would like to test. When the scanner has established connection with the vehicle, the Function Menu displays. Figure 5-8 Sample Function Menu Screen 5.1.2 Control Modules Control Modules displays all controllers available of the vehicle manufacturer. The controllers listed on the menu do not mean that they are installed on the vehicle.
Figure 5-9 Sample Control Modules Screen 2. Select a system to test. When the scanner has established connection with the vehicle, the Function Menu displays. Figure 5-10 Sample Function Menu Screen 5.2 Diagnostic Operations After a system is selected and the scanner establishes communication with the vehicle, the Function Menu displays.
5.2.1 Read Codes Read Codes menu lets you read trouble codes found in the control unit. There are 4 types of code status: ● Present/Permanent/Current ● Pending ● History ● Self-diagnostic Present/Permanent/Current codes stored in a control module are used to help identify the cause of a trouble or troubles with a vehicle. These codes have occurred a specific number of times and indicate a problem that requires repair. Pending codes are also referred to as maturing codes that indicate intermittent faults.
snapshot of critical vehicle operating conditions automatically recorded by the on-board computer at the time of the DTC set. It is a good function to help determine what caused the fault. Figure 5-12 Sample Trouble Code Screen Figure 5-13 Sample Freeze Frame Screen ● Help - select one fault code from the code list and click Help button on the screen. The screen will display the detailed descriptions about the fault code and repair guide. 41 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 5-14 Sample DTC Help Screen 2. Slide up and down to view additional information when necessary. 3. Press Save to store DTC information. Press need be. Press to print the information if to exit. 5.2.2 Clear Codes Clear Codes menu lets you to clear all current and stored DTCs from a selected control module.
2. Follow the on-screen instructions and answer questions about the vehicle being tested to complete the procedure. 3. Check the codes again. If any codes remain, repeat the Clear Codes steps. 5.2.3 Live Data Live Data menu lets you view real time PID data in text and plot formats, learn good sensor data and compare them with faulty data, and record live data from a selected vehicle electronic control module. Menu options typically include: ● All Data ● Custom List 5.2.3.
Figure 5-17 Sample Live Data Screen Name Button Description Help To provide help information of a PID To Top To move a data line to the top of Data List screen History To view the previous live data records or test reports Record To make record of live data Save To save live data of current frame Pause To stop recording live data Table 5-1 Live Data Screen Button Screen ● Learn Mode: gives you the ability to learn good live sensor data values during idle, KEKO, acceleration, deceleration, pa
Figure 5-18 Sample Learn Mode Screen Mode - If that vehicle comes in is with a problem, you can easily compare the faulty sensor and parameter readings to the good readings, and you will be alarmed when a faulty sensor reading is detected. ● Compare Figure 5-19 Sample Live Data Screen 3. Swipe the screen up and down to view additional information when necessary. 4. To move a data line to the top of Data List screen, just tap the line to select and then press the button To Top.
Figure 5-20 Sample PID Graph Screen ● Multi-graphs: displays the parameters in waveform graphs, giving you the ‘real picture’ of what’s going on in the vehicle. Figure 5-21 Sample Multi-graphs Screen ● Merge Graph: merges multiple PID plots into one coordinate, so you can easily see how they affect each other, providing you with the most comprehensive and functional look at live data possible. Figure 5-22 Sample Merge Graph Screen 46 Premier Diagnostic Platform II i80 Max User's Manual V1.
5.2.3.2 Custom List Custom List menu lets you to minimize the number of PIDs on the data list and focus on any suspicious or symptom-specific data parameters. To create a custom data list: 1. Press Custom List from the menu to display all available parameters from the selected control module. 2. The custom data stream selection screen displays. Tap the lines you wish to select. 3. To deselect an item, tap the line again. Alternatively, tap SELECT ALL or CLEAR ALL to select or deselect all items at once.
1. Press ECU Information from Select Diagnostic Function menu. Figure 5-25 Sample Function Menu Screen 2. A screen with detailed information of the selected control module displays. Figure 5-26 Sample ECU Information Screen 3. Press Save to store ECU information. Press need be. Press to print the information if to exit. 5.2.5 Active Tests Active Tests, also known as Actuator Tests, are bi-directional diagnostic tests on vehicle systems and component.
shut down, turn the ignition to the run position, then re-initiate the actuator tests. IMPORTANT The tests activate a component, but they do not check if the component is working correctly. Make sure the components to be tested are in good condition and correctly mounted. NOTE Available tests depend on the control module under test and the vehicle itself. To start a test: 1. Press Active Test from the menu and a list of available options displays. Figure 5-27 Sample Function Menu Screen 2.
Before running any tests, always observe the safety instructions provided in this manual and the warnings provided by the vehicle manufacturer. In addition, follow any warnings and descriptions provided on the scanner screens. ● Never run the tests while the vehicle is moving. ● 5.2.6 Special Functions These functions perform various component adaptations of the control module under test, allowing you to recalibrate or configure certain components after making repairs or replacement. 5.
2. Select Service option from the Special Functions menu. A list of available services display. Figure 5-30 Sample Special Functions Screen 3. Select the service you want to perform. Follow on-screen instructions to make proper selections and operations to complete the tests. Figure 5-31 Sample Service Function Screen 5.3.2 Coding and Programming i80 Max allows for the coding and programming of a replacement control module or changing previously stored incorrect coding.
Figure 5-32 Sample Main Menu Screen 2. Select Programming option from the Special Functions menu. A list of available services display. Figure 5-33 Sample Special Functions Screen 3. Select the function you want to test. Follow on-screen instructions to make proper selections and operations to complete the tests 52 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 5-34 Sample Programming Screen 5.3.3 Hot Functions It is designed for most common used functions like battery configuration, oil light reset and provides quick access to service functions for the technicians. To start a test: 1. Select Special Functions from main menu and press ENTER to confirm. Figure 5-35 Sample Main Menu Screen 2. Select Hot Functions option from the Special Functions menu. A list of available services display. Figure 5-36 Sample Special Functions Screen 3.
Figure 5-37 Sample Hot Functions Screen 6 Maintenance This section gives brief instructions of the most commonly required service and maintenance operations. Typical service operation screens are a series of menu driven executive commands. Follow on-screen instructions to complete the operation.
Oil Reset with One Button - applicable to GM models only. It offers quick and simple oil service reset with the click of one button. ● Manual Reset - almost all Asian vehicles and most American and European vehicles have mechanical oil service indicator reset. The service tool does not have to communicate with the vehicle being tested, but guides you to complete the service manually by providing step-by-step on-screen instructions.
Perform activation/service work on Volvo PBM vehicles – allows to perform installation check, applying parking brake, releasing parking brake, activating service mode and exiting service mode. ● Reset memory on Toyota EPB vehicles – allows to clear the learned memory of the EPB ECU. ● Perform brake cable replacement and electric parking brake replacement – allows to fit in or remove the brake cable safely, adjust brake cable’s tension and calibrate the electric parking brake replacement.
3. Boost the device and select BRT; it will display all the vehicle makes available. Choose your vehicle make and follow the scanner instruction to start. ● Sensor calibration on Honda EPB vehicles - allows to program the current output value of each sensor into the electric parking brake unit. ● Perform BRT on Citroen/Peugeot cars – make several selections to confirm your car model, and then complete the battery replacement following on-screen instructions.
6.7 Continuous Variable Transmission (CVT) This function is used to reset the compensation code and initialize the ECT after a solenoid valve or valve body assembly has been replaced. 6.8 Gear Learning The crankshaft position sensor learns crankshaft tooth machining tolerance and saves to the computer to more accurately diagnose engine misfires. If tooth learning is not performed for a car equipped with Delphi engine, the MIL turns on after the engine is started.
pedal. Air trapped in the lines, calipers or wheel cylinders will make the pedal feel soft and spongy. Air is compressible, so when the brakes are applied any air bubbles in the system must first be compressed before the hydraulic fluid will transmit pressure to apply the brakes. 6.13 Key Programming/Immobilizer The transponder key is an aftermarket option that can be programmed for a number of vehicles.
7.1.1 How to Save an Image To take a screenshot: 1. If want to save data of current screen, press screenshot. at the title bar to take a Figure 7-2 Sample Screenshot Screen 2. Add a description of the image, and press the OK to save. Figure 7-3 Sample Screenshot Screen 7.1.2 Review Image To review the screenshots: 1. Press Data Manager from home screen of i80 Max diagnostic application. 2. Press Image and all available pictures will be displayed.
Figure 7-4 Sample Browse Picture Screen 3. To delete a picture, tap button Delete and answer OK to delete. Press Print to print the pictures and press Rename to change the picture name. Figure 7-5 Sample Edit Picture Screen 4. Long press the screen to edit all pictures like Rename or Delete. Figure 7-6 Sample All Pictures Edit Screen 61 Premier Diagnostic Platform II i80 Max User's Manual V1.
7.2 Reports PDF option leads to screens for review of the vehicle test reports. You just need to press the reports icon on the test screen, add a description and press OK button to save. 7.2.1 How to Create a Report To create a report: 1. If need be, press the Save icon on the test screen to save the data. Figure 7-7 Sample of DPF Screen 2. Add a description to the report, and press the OK to save. 7.2.2 Review Reports To review the reports: 1.
Figure 7-9 Sample Edit PDF Screen 7.3 Data Playback The Data Playback option leads to screens for review of recorded live data. Playing back a recording is just like using the scan tool on a live vehicle. It let you review live data in text, graph and graph merging formats. Playback speed and direction (forward or reverse) can also be controlled. To review recorded live data: 1. Press Data Manager from home screen of i80 Max diagnostic application. 2. Press Data Playback and all available records display.
Figure 7-11 Sample Graph Screen 5. To move forward or reverse back of the playing, just drag the progress bar forward or reverse. To stop, press the Pause button. Figure 7-12 Sample Edit Data Playback Screen 6. Long press the record to Rename or Delete the records. 7.4 Data Logging & Data Record Data Logging collects the communication data between the scanner and the vehicle under test to help with troubleshooting of diagnostic failures. The logs will be saved to the tablet.
Figure 7-13 Sample Data Logging Screen 2. Click the Data Logging icon again to stop the recording and data log record will be saved automatically. 3. Go to Data Manager -- Data Record to view the stored logs. 8 VCI Manager VCI Manager allows you to make Bluetooth pairing between the tablet and the VCI dongle, update VCI firmware and unbind a VCI dongle. Figure 8-1 Sample VCI Manager Screen 8.
1. Connect the VCI dongle with a vehicle via diagnostic cable or connect to the tablet with the USB Type-B cable. 2. Click the VCI Manager application on the i80 Max Menu. 3. Select Bluetooth option from the list. 4. Select the right device with the i80 Max serial number from the list. 5. When paring is successfully done, the status is shown as Paired. 6. Wait a few seconds, and the button at the toolbar illuminates green, indicating the tablet is connected to the VCI dongle via Bluetooth.
Figure 8-3 Sample Update Prompt Screen 8.3 Unbind a VCI dongle This option allows you to unbind a VCI dongle when the VCI dongle is defective or stolen. To unbind a VCI dongle: 1. Click the VCI Manager application on the i80 Max Menu. Figure 8-4 Sample VCI Manager Screen 2. Select Unbind a VCI dongle option from the option list and press OK to confirm. 67 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 8-5 Sample Unbind Prompt Screen To bind a new VCI dongle: 1. Connect the VCI dongle with i80 Max tablet via USB cable. Figure 8-6 Sample Bind Prompt Screen 2. When system database initialization finished, you can use the tablet normally. 68 Premier Diagnostic Platform II i80 Max User's Manual V1.
Figure 8-7 Sample Data Initialization Screen 9 Registration and Update The scanner can be updated to keep you stay current with the latest development of diagnosis. This section illustrates how to register and update your scan tool. You can register both on Foxwell website or by the built-in update client. NOTE Before registration and updating, please make sure your network works correctly and the tablet is fully charged or connect to external power supply. 9.
Figure 9-2 Sample ID Registration Screen 3. Enter one of your email addresses as your user ID and click the Send Code button. We will send a 4-digit verification code to the email you just entered. Find the security code in your mailbox, input the code, create a password and click Free Registration to complete. Figure 9-3 Sample ID Registration Screen 4. “The account has been created successfully” message will appear if you registered successfully.
Figure 9-4 Sample Registration Done Screen 5. The serial number will be recognized automatically and click Submit to activate the scanner. Figure 9-5 Sample Product Activation Screen 6. The product is registered successfully. Figure 9-6 Sample Activation Done Screen 71 Premier Diagnostic Platform II i80 Max User's Manual V1.
9.1.2 Register through Website To register through our website: 1. Visit Foxwell official website www.foxwelltech.us and press Register icon, or go to the registration page by selecting Support from home page and then click Register. Figure 9-7 Sample Website Register Screen Figure 9-8 Sample Website Register Screen 2. Enter one of your email addresses as your user ID and click the Send Code button. We will send a 4-digit verification code to the email you just entered.
Figure 9-9 Sample Create Account Screen 3. Sign in to the Member Center, click New Registration, input the right serial number and click Submit to activate the product. Figure 9-10 Sample Product Register Screen 9.2 Update To update the diagnostic application: 1. Press Update from home screen or press update shortcut at the tool bar, and the update client starts up automatically. 2. The available updates display.
Figure 9-11 Sample Update Screen 10 Settings This section illustrates how to program the scanner to meet your specific needs. When Settings application is selected, a menu with available service options displays. Menu options typically include: ● Unit ● Language ● Font Size ● Push Message ● Automatic Update ● System Settings ● General ● Uninstall Vehicle Software ● Print Settings ● About 10.
10.2 Language Select Language opens a screen that allows you to choose system language. To configure system language: 1. Press Settings from home screen of the i80 Max diagnostic application and select Language. Then all available language options display. 2. Select your preferred language and click Yes to confirm. Figure 10-1 Sample Language Setting Screen 10.3 Font Size Select Font Size opens a screen that allows you to choose the font size. To configure Font Size: 1.
Figure 10-2 Sample Font Size Setting Screen 10.4 Push Message This option allows you to enable/disable Push Message function. Software updates and technical information will be delivered to you automatically. It is highly recommended to enable it all the time, so you won’t miss out any new updates from Foxwell. To enable/disable Push Message: 1. Press Settings from home screen of the i80 Max diagnostic application. 2. Click the button on the right side.
Figure 10-4 Sample Update Remark Screen 10.6 System Settings This option provides you a direct access to the Android system settings, like sound, display, system security and etc. Refer to Android documentation for more information. 10.7 General This option lets you to turn on/off the prompt when saving a file or login & registration when started the scanner. 10.8 Uninstall Vehicle Software This option allows you to uninstall the vehicle software installed in the scanner.
Figure 10-6 Sample Uninstall Vehicle Software Screen 10.9 Print Settings This option allows you to print any data or information anywhere and anytime either via PC network or Wi-Fi. To setup the printer connection: 1. Tap the Settings application on home screen of i80 Max. 2. Tap the Printing Settings option on the option list. Figure 10-7 Sample Print Settings Screen 3. Tap Print Plugin Manager and turn on the Mopria Print Service, then i80 Max will search for available printers automatically.
Figure 10-8 Sample Print Service Manager Screen Figure 10-9 Sample Setting of Print Service Manager Screen 4. Choose the right printer. Figure 10-10 Sample of Printer Screen 5. Choose the file or report you want to print and press the print icon 79 Premier Diagnostic Platform II i80 Max User's Manual V1.01 .
Figure 10-11 Sample of File Printing Screen NOTE 1. Please make sure the printer and the i80 Max in the same Wi-Fi or Network when printing. 2. If Mopria Print Service driver can’t workable for your printer, please download the driver to work for your printer on Print Service Manager. 10.10 About Selecting About option opens a screen that shows information about the i80 Max, such as serial number, hardware and software version and etc. To view information of your scan tool: 1.
11 Shop Manager This section illustrates how to manage the workshop information, vehicle test records and customer information. When Shop Manager application is selected, a menu with available service options displays. Menu options typically include: ● Vehicle History ● Workshop Information Figure 11-1 Sample Shop Manager Screen 11.1 Vehicle History This function keeps records of tested vehicles, including vehicle information and the fault codes from previous diagnostic sessions etc.
11.2 Workshop Information The Workshop Information allows you to edit, input and save the detailed workshop information, such as shop name, slogan, address, phone number and more. It will show as the header of the printed documents when printing vehicle diagnostic reports and other test files. Figure 11-3 Sample Workshop Information Screen 12 My Account This section displays the information related to your account and product.
12.1 My Account My Account option allows you to check and modify your account information including user name, e-mail, telephone, address and so on. Figure 12-2 Sample My Account Screen 12.2 My Products This option let you activate a new product and manage activated products including serial number and expiration date. Figure 12-3 Sample My Products Screen 12.3 Push Message It will display all messages you got from Foxwell including software update notice and product news.
13 Remote Support Remote Control enables you to get remote support from Foxwell with TeamViewer when you have issues with Foxwell products. If you need our team to remote control your i80 Max, 1. Click the Remote Control icon on the main menu of the i80 Max to start TeamViewer. Figure 13-1 Sample Remote Control Screen 2. Press QuickSupport icon and the TeamViewer ID will show. Figure 13-2 Sample QuickSupport Screen 3. Send your ID to us to let our team to take control your tablet.
Figure 14-1 Sample Technical Data Screen FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
