User manual
3D FPV camera The BlackBird 2 User manual Tables of contents 1. Description and operation .......................................................................................... 2 1.1. Product description .................................................................................................. 2 1.2. Specifications ............................................................................................................ 3 1.3. Equipment ...................................................
D FPV camera The BlackBird 2 User manual 1. Description and operation 1.1.
3D FPV camera The BlackBird 2 User manual 1.2. Specifications Тable 1 Video sensor Model Aptina MT9V136 Size and type of the matrix 1/4'' CMOS Size of the array of pixels 680 x 512 Sensitivity 11.9V / Lux- sec @ 550nm Signal / noise ratio 45 dB Optics Focal length of the lens 2.
3D FPV camera The BlackBird 2 User manual 1.3.
3D FPV camera The BlackBird 2 User manual 1.4. Construction Desing description: front view Picture1 back view Picture 2 name № number 1 Printed circuit board 1 part 2 Lens mount 2 parts 3 Lens 2 parts 4 Lens fixing screw (in some models the locking ring) 2 parts.
3D FPV camera The BlackBird 2 User manual Connector pinout: DF13-10P-1.25 H 1 pin: -3.3V output for external devices. Current less than 100mA 2 pin: GND 3 pin: MAVLINK RX(UART 3.3V) 4 pin: MAVLINK TX(UART 3.3V) 5 pin: GND 6 pin: +5V...
3D FPV camera The BlackBird 2 User manual 1.5. Desing and operation The basis of the BlackBird 2 are two video sensor and optical system. The signal from the video sensor is processed in the FPGA chip, where the signal is generated in the required 3D format. Further there is a digital-to-analog conversion and the signal is transmitted to the interface, the modular connector and a mini USB port of your camera. 1.6.
3D FPV camera The BlackBird 2 User manual 2.2. Preparing for use Connect video and power Before you begin, you need to connect the BlackBird 2 output to a video playback device or a video transmitter2, and also to a power source. To do this, connect the interface cable or a preconfigured full cable to the interface connector of the BlackBird 2. The yellow RCA connector of the interface cable is connected to the playback device or a video transmitter.
3D FPV camera The BlackBird 2 User manual 2.3. Use of the menu Adjusted and correctly connected the camera starts to operate immediately after power-up. A lit up green LED 13 (see Picture 2) indicates the power supply is on. Table 2: Menu name and description of the menu item count of fast flashing green LED «MENU» Selecting video mode – allows you to select an outgoing video format 1. Side by side 3D crop 16x9 2. Side by side 3D crop 4x3 3. Side by side 3D full frame 4.
3D FPV camera The BlackBird 2 User manual 3. Connect to PC and update software To connect BlackBird 2 to a personal computer or laptop will need a cable Mini USB - USB. Before connecting the USB cable, disconnect camera from all power sources. The BlackBird 2 is connected to a power source (e.g.
3D FPV camera The BlackBird 2 User manual 4. Maintenance and calibration 4.1. Lens focus adjustment If an image displayed by the BlackBird 2 is blurred, the lenses should be focused. Table 3 Examples of possible lens focus options.
3D FPV camera The BlackBird 2 User manual 4.2. Adjusting the vertical image shift A vertical shift of the images will be perceived by the viewer as disconcerting. The presence of vertical displacement can quickly tire the eyes, lead to an incorrect perception of distance and possibly headache. Table 4: Examples of possible vertical image shift.
3D FPV camera The BlackBird 2 User manual 4.3. Selecting the video format To change the stereo image format, choose the menu item «Selecting the video mode»3 and «NEXT» button or «BACK» to select the desired stereo image format. After selecting wait until the red LED goes out - it will mean that the camera has stored your settings and is ready for use. 4.4.
3D FPV camera The BlackBird 2 User manual «BACK». After a wait until the red LED goes out - this means that the camera remembers the settings you made - they are stored in memory for use and after Power Off or a power failure, you will not have to adjust them again. 4.5.
3D FPV camera The BlackBird 2 User manual errors After turning on of the camera three LEDs are lit, there is no picture on any of the outputs reason elimination The use of the defective cable Mini USB-USB Change the cable. The fault of crystal oscillator. Contact support service of FPV3DCAM company. 15 2016 fpv3dcam.