Operating manual UK
Frama Matrix F32/F42/F62 Operating manual for Frama Matrix F32 Frama Matrix F42 Frama Matrix F62 MF/MFD manual feeder AF/AFS automatic feeder All rights reserved. Frama Group.
Frama Matrix F32/F42/F62 Dear Customer, Thank you for choosing one of the innovative, forward-looking Frama Matrix F32/F42/F62 franking solutions which meets all standards and therefore guarantees long-term protection of your investment. The information below in this operating manual is intended to assist you in installing and operating your Frama Matrix F32/F42/F62. It also shows how you can easily make settings yourself. We have summarized the most important points briefly here for you.
Frama Matrix F32/F42/F62 Safety information and warnings Thank you for deciding to purchase the innovative Frama Matrix F32/F42/F62 franking system. The information below in this operating manual is intended to assist you in installing and operating your Frama Matrix franking system. It also shows how you can easily make settings yourself. This franking system meets current safety requirements. Incorrect use can, however, lead to injury and damage.
Frama Matrix F32/F42/F62 Table of contents SAFETY INFORMATION AND WARNINGS ................................................................................................... 4 SYMBOLS USED .............................................................................................................................................................. 4 TABLE OF CONTENTS ....................................................................................................................................... 5 1.
Frama Matrix F32/F42/F62 7.3. SETUP 3 MENU ..................................................................................................................................................... 55 8. ADMIN MODE ...............................................................................................................................................56 8.1. LOG IN ...............................................................................................................................................
Frama Matrix F32/F42/F62 1. System presentation 1.1. Safety instructions/Notes on use 1. Danger Use this franking system indoors and for franking post and franking labels only. Any other use, modification or change to the franking system is not permissible and may be dangerous. The manufacturer accepts no liability for damage caused by use contrary to the intended use or incorrect operation. 2. Check the franking system for external damage before setting it up.
Frama Matrix F32/F42/F62 1.2. Use as intended/Notes on print quality The following notes are intended to support you in achieving a sharp, professional print with your Frama Matrix franking system, so as not to jeopardize the delivery of your franked mail. As the user, you are responsible for the legibility of your franking. 1. 2. 3. 4. 5. Information 6. 7. 8. 9. Your franking machine must be properly registered with the Royal Mail before you use it for the first time.
Frama Matrix F32/F42/F62 1.4. Recycling and disposal The WEEE Directive (Waste Electrical and Electronic Equipment; 2002/96/EC) was drawn up for the protection of human health and the environment to ensure that waste products are disposed of utilizing the best available reprocessing, recovery and technical recycling possibilities. Your product has been developed and manufactured using top-quality materials and components which can be recycled and reprocessed.
Frama Matrix F32/F42/F62 1.5. The Frama Matrix machine The figures below show the principal components of the Matrix F32/F42/F62 franking system. Please familiarise yourself with the location of the components. Fig. Matrix F62, front view: Ink system Feeder lock Letter tray Touch screen Water tank (F62AFS only) Matrix F62 franking system Label dispenser cover Side stop AF/AFS feeder Fig.
Frama Matrix F32/F42/F62 Fig. Matrix F42 and Matrix F32, front view Ink system Letter tray Touch screen Matrix F32/F42 franking system Label dispenser cover (Matrix F42 only) MFD feeder (F42) MF feeder (F32) Fig.
Frama Matrix F32/F42/F62 1.6. Basic screen layout The Frama Matrix F32/F42/F62 franking systems use a colour touch screen for operation and navigation through the menus. The colour scheme can be modified in the Setup 3 menu. Tip Detailed information concerning the tariff control system screens is available in section 4.3. Determining postage value from page 22. All the functions that are not available are hidden as a rule.
Frama Matrix F32/F42/F62 2. Installation In the normal event, the machine will be installed by a member of our after-sales technical team. You must also follow the steps in the installation instructions enclosed separately if you wish to install the machine yourself. There are four steps to installation: 1. Assembly of the individual components 2. Registering with the FramaOnline2 system 3. Configuring the printer settings 4.
Frama Matrix F32/F42/F62 2.3. Making connections The figure below shows the location of the interfaces on the rear of the Matrix franking system's housing (connection panel). Serial port (RS232 - PC) Communications module USB port (USB B) Scales socket USB port (USB A) 2.3.1. Make communications connection (communications module) The connection of the relevant cable differs depending on the communications module used. Ethernet (green): Plug the network cable (RJ45) into this socket.
Frama Matrix F32/F42/F62 2.6. Connecting to the mains electric supply 1. 2. Danger 3. 4. 5. 6. Check the franking system for external damage before setting it up. You may be putting your life at risk by using a damaged machine. Check the cable and plug before installing the system. Have any damage repaired by a specialist electrician only. Do not use the machine until the damage has been repaired. A damaged connecting lead may only be replaced by a lead of the same type.
Frama Matrix F32/F42/F62 2.8. FramaOnline2 installation Installation on the FramaOnline2 data centre establishes the full functionality of your franking system and is indispensable for the correct operation of the system. Information: It may be necessary to configure your franking system to ensure that it connects successfully with your network. Follow the instructions on page 59 to make the necessary settings. Information A note on installation appears once the system is switched on. 1.
Frama Matrix F32/F42/F62 3. FramaOnline2 3.1. General notes FramaOnline2 will deal with preparing the postage rates, sending usage data to Royal Mail and provides a simple way of loading new postage credit onto your franking system. Your franking system must set up a connection with the data centre to allow use of FramaOnline2. Refer to section 9.4. Connection on page 59 for this. Tip It is only possible to call up postage and communicate with FramaOnline2 in Admin mode.
Frama Matrix F32/F42/F62 Enter the Re-set Value desired. Confirm your choice by pressing OK. The query for the Re-set Value is omitted in some countries. In this case, the full amount available is loaded every time. 7. Your Frama franking system establishes a link with the FramaOnline2 data centre and keeps you informed as to the progress of the connection. Tip The connection can last several minutes depending on the amount of data to be transferred (postage rates update, etc.).
Frama Matrix F32/F42/F62 4. Operation 4.1. Switching on and off Always use the mains switch to switch your franking system on or off after shutting it down. Press “i“ on the mains switch to switch the machine on. You must always press the System shut-down key to shut down the franking system before you switch your Matrix franking system off. This procedure ensures that the print head is properly sealed and cannot dry out.
Frama Matrix F32/F42/F62 4.2.2. Displaying the cost centre data R1-Value/R1-Number: Resettable counters for period 1 R1-Value shows the postage used since the last time this counter was reset. R1-Number shows the number of mail items franked since the last time this counter was reset. R2-Value/R2-Number: Resettable counters for period 2 R2-Value shows the postage used since the last time this counter was reset. R2-Number shows the number of mail items franked since the last time this counter was reset.
Frama Matrix F32/F42/F62 4.2.5. Changing the cost centre PIN The cost centres are protected by a PIN by default. In the as-delivered state of the franking system, the PIN is the same as the cost centre number. The PIN can have up to 4 digits. Proceed as follows to change the PIN for the current cost centre: Press the Change PINs key (in Setup 1 or in the CC Manager under CC Setup). Enter the old PIN. Press OK to confirm. Enter the new PIN. Press OK to confirm.
Frama Matrix F32/F42/F62 4.3. Determining postage value Tip Your franking system protects you against unintentionally franking at high postage rates (see Settings section). By default, all franking valued over £10.00 must be approved by touching the postage value displayed (it is initially displayed inverted). This value can be configured in Setup 2 (section 7.2.1. High Value on page 54). 4.3.1.
Frama Matrix F32/F42/F62 4.3.2. OneTouch Press the OneTouch key for the mail product required. The product is set and you can frank the item as soon as the Ready display appears. Press a different OneTouch key to change the product. Further OneTouch screens can be called up by touching the postage value. Each of the OneTouch keys can be reassigned to suit your needs.
Frama Matrix F32/F42/F62 You can also set the Detail-guided start menu to be the permanent default start menu in the Setup 1 menu (see page 53). 4.3.4. Tariff-guided Call up the Tariff-guided start menu by pressing the Weight field in the OneTouch menu. You will also be taken to this menu when batch weighing is complete. Then press the Tariff-guided key. You will be guided through the individual tariff properties one-by-one. The postage will be calculated once the last item for the tariff has been entered.
Frama Matrix F32/F42/F62 4.3.6.2. Using mail item weight for postal rate calculation In the detailed overview or the postage rate calculation, press the Weight key and, at any time, by pressing the Scales 17g key, you can retrieve the weight displayed for calculating the postage rate. Caution The procedure described is possible only in STACK mode. An analogue balance is displayed in the top section of the screen. This shows you roughly how much of the weight category your mail item is using. 4.3.6.3.
Frama Matrix F32/F42/F62 SINGLE mode Place a letter on the scales. The weight is determined and automatically transferred. The display changes to single weighing mode. The Weight key provides information as to the weight of the mail item placed on the scales (here: Single 17 g). The postage is calculated on the basis of this weight. Frank the letter. Place the next letter on the scales. The weight of the letter is displayed and the postage calculated accordingly and so on.
Frama Matrix F32/F42/F62 4.4. Franking 1. 2. Danger 3. 4. 5. 6. Use accessories intended for this system only. The use of accessories that are not approved, or not authorized, can be detrimental to the service life of the franking system. At the same time, a danger to the operator can be created. Always keep your fingers and other parts of the body, ties, necklaces, scarves, open sleeves and similar loose things away from the feed entry area and the feed rollers.
Frama Matrix F32/F42/F62 4.4.2. Setting the side stop on the AF/AFS automatic feeder You can process your mail items straight from the stack using the AF/AFS automatic feeder. It is not necessary for the mail item thickness to be set. The mail items do not have to be fanned out in advanced. Danger Always keep your fingers and other parts of the body, ties, necklaces, scarves, open sleeves and similar loose items away from the feed entry area and the feed rollers.
Frama Matrix F32/F42/F62 4.5. Fitting the ink jet cassettes 4.5.1. Fitting/changing the ink jet cassette Your Frama Matrix franking system uses a double ink jet cassette to frank your mail items. The ink jet cassette also contains the printing head. You must therefore handle the ink jet cassette very carefully. 1. 2. 3. 4. Information 5. 6. 7. Do not frank mail items thicker than 10 mm. You risk allowing the printing head to touch the surface of the mail item and thus smearing the franked mark.
Frama Matrix F32/F42/F62 Unpack the new ink jet cassette and remove the two protective strips from the print head. On the top of the ink jet cassette you will find two grip surfaces. Press them together between your thumb and forefinger. Insert the ink jet cassette from above. Follow the contour of the cover as you do this. Push the new ink jet cassette fully into its guide. Release the grip surfaces.
Frama Matrix F32/F42/F62 Example of a test print: Alignment X is shown on the left and Alignment Y on the right. The setting currently valid for each is indicated by an arrow. The arrows should point to where the lines appear straightest. If this is already the case, you only need to confirm the following displays X and Y by pressing the ENTER key. Sometimes, however, it is necessary for you to change the setting to optimize the results. Simply carry out the additional instructions.
Frama Matrix F32/F42/F62 4.5.2. Topping up the franking labels 4.5.2.1. AF/AFS automatic feeder (MatrixF62 only) Open the label compartment on the AF feeder by lifting up the cover flap. Hook a finger under the cover flap and lift it up. Open the flap completely upwards. Hold the top end of the hook clamp with the left hand and pull it upwards. Keep the hook clamp in this position. Remove the empty label box, if necessary. Put the label box into the channel.
Frama Matrix F32/F42/F62 4.6. AF/AFS automatic feeder (Matrix F62 only) 1. 2. 3. Danger 4. 5. 6. 7. 8. 9. Use accessories intended for this system only. The use of accessories that are not approved, or not authorized, can be detrimental to the service life of the franking system. At the same time, a danger to the operator can be created. Always keep your fingers and other parts of the body, ties, necklaces, scarves, open sleeves and similar loose items away from the feed entry area and the feed rollers.
Frama Matrix F32/F42/F62 Switching the letter sealer on automatically activates the Seal only key. In this event, the mail items will be sealed, but not franked. 1. 2. Information 3. 1. 2. Danger If envelopes that have already been sealed are used with the Letter sealer ON function, this can cause a paper jam as the feeder tries to seal these envelopes again. Never use washing-up liquid additives or other additives which reduce the water surface tension.
Frama Matrix F32/F42/F62 4.6.2.1. Cleaning letter sealer From time to time, the letter sealer must be cleaned or have its wearing parts replaced. Use the Clean letter sealer function. Press the Restart System key after the cleaning operation. The letter sealer is beneath the water tank. Caution: Always use the Clean letter sealer menu item to remove the letter sealer. If you do not, you may damage the letter sealer mechanism. How to clean the letter sealer: Press the Clean letter sealer key.
Frama Matrix F32/F42/F62 4.6.3. Stack function You can define a pre-selection counter with the Stack function. The feeder feeds the preselected number of mail items to be franked and then stops. Press the Stack key in the Feeder menu to switch on the function (Stack ON). Press the key again to switch off the function. Select the Stack mode using the Stack key in the start menu. Enter the number of mail items per stack. Start processing the stack by pressing OK or the number entered.
Frama Matrix F32/F42/F62 4.6.6. Remedying transport fault in AF/AFS automatic feeder The transporting area of the automatic feeder can be opened to clear the transport quickly in the event of a fault (paper jams, pieces of paper left lying, etc.). Caution Always switch off the franking system before you open the transport area cover. There is a risk of injury on rotating parts. Danger How to open the transport area cover: Slide the lock to the left to the open padlock symbol.
Frama Matrix F32/F42/F62 4.6.7. Separating/connecting the feeder and franking system 1. First switch the franking system off, and then pull out the mains plug before you separate the feeder from the base of the franking machine. There is a risk of electric shock and injury. 1. Remove the water tank and the optional letter sealer before you separate the automatic feeder from the base of the franking machine. Incorrect transport may otherwise lead to water damage.
Frama Matrix F32/F42/F62 4.6.7.2. Connecting the franking system Line up the franking system and the AF/AFS automatic feeder opposite one another as shown in Figure 3. The connecting pins on the Matrix franking system must be inserted into the guide holes in the automatic feeder.
Frama Matrix F32/F42/F62 5. Main Menu 5.1. Overview The Main Menu is the main control point for all the important system functions. Press the “ i" in one of the start menus to access the Main Menu. You can select the following functions in the Main Menu. - PP (see page 43) - Devices (see page 43) - Print Date (see page 45) - Message (see this page) - Info Print (see page 46) - Printer Settings (see page 48) 5.2.
Frama Matrix F32/F42/F62 5.2.1. Advertising imprint text blocks Your Matrix franking system gives you the possibility of producing your own advertising imprint text blocks and thus of drawing attention to holidays, special campaigns and events with your mail. A text block can be printed instead of a message or advertising imprint or in addition to a message or an advertising imprint. 5.2.2.1. Entering an advertising imprint text block Press the Enter Text key Select the text to be written.
Frama Matrix F32/F42/F62 5.2.3. Printing message and text simultaneously Your Frama Matrix franking system gives you the possibility of printing your own text in addition to the selected message. You can set this function by pressing Message & Text. Tip Caution If franking labels are used, only restricted utilization of this function is possible. Your Frama Matrix franking system checks the length of the franking mark and will give you a cue if the permissible total length is exceeded.
Frama Matrix F32/F42/F62 5.3. P.P. The F32/F42/F62 Matrix models also allow you to generate PPI marks in addition to the normal franking mark. Select the PPI key in the Main Menu if you wish to be able to generate PPI marks. Make your selection . You can now frank your letters. A counter provides information as to the number of mail items franked. The Label key generates franking strips printed with the appropriate PPI mark. 2 You can reset the counter to 0 with the Reset Counter key.
Frama Matrix F32/F42/F62 5.4.2. Scales (optional) Connecting the S2 or S5 scales automatically extends the functional scope of your Matrix franking system, i.e. you can use the scales functions described immediately. By using the electronic scales, you are able to calculate postage rates and weigh your letters, small parcels as well as other mail items accurately. You therefore automatically avoid incorrect franking.
Frama Matrix F32/F42/F62 5.5. Print date Sometimes, it might be necessary for your mail to be franked several days before the delivery date. To this end, you can set the date printed in the Frama Matrix frank mark up to thirty days ahead. You can bring forward the date using the + key. You can push back the date you have previously brought forward using the - key. The Reset key brings you to the current date. Confirm your choice by pressing the ENTER key.
Frama Matrix F32/F42/F62 5.6. Info Print You can set various print modes for your Matrix franking system using the Info prints. The reports are particularly important. These allow condensed information to be printed out. These reports help you by providing overviews when you are programming or, for example, they may be used as receipts after loading postage via the FramaOnline2 data centre. You can call up further Info Prints by pressing the Next key (right arrow). 5.6.1.
Frama Matrix F32/F42/F62 5.6.7. Statistics report The statistics report is used to print out the statistics for the current period. The data collected correspond to the items you have mailed in the time between two connections with the FramaOnline2 data centre. The report extends over several pages (depending on the volume of statistics). After connecting with the FramaOnline2 data centre, the statistics are automatically deleted and then recompiled using your consumption data. 5.6.8. P.P.
Frama Matrix F32/F42/F62 5.7. Printer Settings 1. 2. 3. 4. Information 5. 6. 7. Do not frank mail items thicker than 10 mm. You risk allowing the printing head to touch the surface of the mail item and thus smearing the franked mark. You should therefore always use Frama Matrix franking labels for thick letters and packets. Please make sure that no sharp objects, such as paper clips, are near the franking zone. This can damage the print head.
Frama Matrix F32/F42/F62 Thorough cleaning of nozzles: Intense rinsing and cleaning of the nozzles and print head. To call up the required program, press the corresponding button. The cleaning program starts automatically. It is recommended that afterwards you perform the "Nozzle test" function to check that the cleaning was successful.
Frama Matrix F32/F42/F62 5.7.3. Service The service station is run under the print head after a specified time if you briefly interrupt franking, e.g. because you are inserting new mail items. This means that there is a delay after new mail items are inserted in the machine, as the station must first be parked again. You can use the Service setting to define the time that the franking system waits before the service station is run under the print head.
Frama Matrix F32/F42/F62 6. Counter Readings You can access the counter readings from the Main Menu by pressing the “i“ key. The data for the current cost centre is first: R1-Value/R1-Number: Resettable counters for period 1 R1-Value shows the postage used since the last time this counter was reset. R1-Number shows the number of mail items franked since the counter was reset the last time.
Frama Matrix F32/F42/F62 7. Setup (settings) You can adjust various settings for your Frama Matrix franking system in the Setup menu. Outside Admin mode, you only have the Setup 1 menu available. Press the “i“ key on the Main Menu twice. Then press the Spanner to access the Setup menu. Calling up the Setup menu Press “i“ Press “i“ Press spanner Use the arrow key to access two further Setup menus in Admin mode. Press ESC to return. 7.1.
Frama Matrix F32/F42/F62 7.1.4. Status List This key displays a status list. These data and the data in the system information provide important input for our customer service. 7.1.5. Start Up/Log Off Use this key to restart the system after you have adjusted settings. Pressing Start Up/Log Off takes you straight to cost centre selection. 7.1.6. Save Start Menu Here you can save a Start Menu as the default.
Frama Matrix F32/F42/F62 7.2. Setup 2 menu Setup 2 menu can only be called up in Admin mode (see page 56). 7.2.1. High Value This setting determines that amount from which, for security reasons, you must confirm the postage value before this amount can be franked. The default setting is £10.00. Enter the new value and confirm your input by pressing ENTER. 7.2.2. Max. Value Define the maximum permitted franking value with this setting.
Frama Matrix F32/F42/F62 7.3. Setup 3 menu Setup 3 menu can be only be called up in Admin mode. 7.3.1. Logo Use this setting to define whether all cost centres have to work with the same logo or whether each cost centre may use an individual logo (default = Logo CC). Logo SYSTEM: All cost centres automatically use the logo defined in Admin mode. The Admin mode has an appropriate function in the Main Menu where you can define the logo. Logo CC (default): Each cost centre can use an individual logo.
Frama Matrix F32/F42/F62 8. Admin mode Settings made in Admin mode always apply to all cost centres. In Admin mode you also have access to all cost centres and can thus conveniently make settings for these cost centres (counter readings, name and PIN). The additional features demanded by Admin mode are described below. Tip You can also make settings in each cost centre. However, when you do this not all the Admin mode functions are available to you. 8.1.
Frama Matrix F32/F42/F62 8.2.3. Info Print In Admin mode, the Cost Centre report has extended selection options for the cost centres to be printed. All other reports and print options correspond to the descriptions given earlier in this operating manual (see section 5.6. Info Print from page 46). Select CC List from Report CC. Enter the first cost centre to be printed. Confirm the entry by pressing OK. Enter the last cost centre to be printed. Press OK to confirm. Insert envelopes, report cards, etc.
Frama Matrix F32/F42/F62 8.4.2. Reset Counters Press Reset Counters and select the period to be deleted. Deleting period 2 automatically also deletes period 1. Select the counters to be reset for a cost centre (Other CC) or a range of cost centres (CC range). The All CCs key deletes the selected period for all cost centres. Confirm the security prompts to delete the desired cost centres. 8.4.3. Setup 2/Setup 3 The settings for Setup 2 and 3 have already been described in detail from page 54.
Frama Matrix F32/F42/F62 9. FramaOnline2 FramaOnline2 is a service provided by Frama which handles postage payment (credit), sends franking data to Royal Mail, sends logos electronically and provides the latest postage rates for you. The FramaOnline2 menu is described below. 9.1. Loading postage credit The procedure for loading credit (postage) has already been described in depth on page 17. 9.2. Inspection You can run inspection loadings with your Frama Matrix franking system.
Frama Matrix F32/F42/F62 9.4.1 Network Setup The instructions for configuring the network connection are supplied separately and are not the subject of this operating manual. In the as-delivered condition, dynamic configuration by DHCP is preset; this provides an automatic connection of your Frama franking system in most cases. FramaOnline2's address is: fo2.frama.com. Communicate using https via port 443.
Frama Matrix F32/F42/F62 9.7. SmartShop SmartShop allows you to order frequently required accessories directly through your franking system. Call up the SmartShop by pressing its key. The subsequent figures may differ depending on your country. The prices are shown for illustration purposes only. 9.7.1. Order accessories/options Select the item required by pressing the relevant key. Select the desired quantity of the item using the - and + keys. Press the Order key again to confirm the item selection.
Frama Matrix F32/F42/F62 10. Troubleshooting/Error messages In the event of a malfunction, a message will appear in the display of your Frama franking system. If you are unable to eliminate the problem yourself, you can obtain support on your Frama hotline or from your local Frama dealer. Keep your customer number and franking system number ready to hand.
Frama Matrix F32/F42/F62 10.2. Scales messages Display message Cause Remedy Scales communication error Frama Matrix franking system Check that the scales cable is plugged not communicating with in properly. Switch the franking system scales. off and then on again. Please contact us on our hotline if this does not correct the problem. The scales do not come to rest The scales platform is not at rest. It is therefore not possible to determine the weight.
Frama Matrix F32/F42/F62 10.3. Franking value/Credit Display message Cause Remedy High value not confirmed. Security prompt. Touch the postage value shown inverse in the display. You can change the postage limit that activates the message in the Setup 2 menu in Admin mode. Maximum Franking Value Exceeded ! Security prompt. The value exceeds the maximum postage value. You can change the postage limit that activates the message in the Setup 2 menu in Admin mode.
Frama Matrix F32/F42/F62 10.4. Printer messages Display message Cause Remedy Perform Calibration of Ink Jet Cassette? You have inserted an ink jet cassette that has previously been fitted in your Matrix franking system. Select YES if you wish to recalibrate the ink jet cassette or NO if you wish to apply the existing calibration data. Please insert a suitable cassette. Incorrect cassette type Please use only suitable ink jet cassettes. Cassette not recognized.
Frama Matrix F32/F42/F62 10.5. Feeder and printing Display message Cause Remedy Feeder error. Please feed the letters in again. A letter was fed at an angle and thus not franked. Feed in the letter again. Caution The selected mark is too long for label printing (advertising and text). The printing mark does not fit onto a franking tape. Temporarily switch off the text or advertising using the selection function. Caution The selected mark (logo and text) is too long for the current letter.
Frama Matrix F32/F42/F62 Not straight/paper jam Please re-insert the letters and frank again. The letter has been drawn in at an angle. This means that it has not been possible to print it. The franking image has been buffered. Insert the last (unfranked) letter again. The letter will now be franked. Not straight/paper jam Reprinting required. Please confirm. The letter has been drawn in at an angle. This means that it has not been possible to print it. The franking image has been buffered.
Frama Matrix F32/F42/F62 11. Technical data 11.1. General Matrix F62 speed: Matrix F32/F42 speed: 5500 letters/hour 4000 letters/hour Maximum letter thickness: Display: Default process: Number of fixed stored advertising messages: Number of customer-specific advertising messages: 10 mm graphical, touch-sensitive screen FramaOnline2 3 8 (Matrix F42/F62) 6 (Matrix F32) 3 52 x 25 mm Number of freely definable texts: Dimensions of advertising message: 11.2.
Frama Matrix F32/F42/F62 Envelope flap specifications/maximum and minimum envelope dimensions: Figure: Envelope flap specification for letter sealer/maximum and minimum envelope specifications 11.3. Power supply rating Matrix F62: AF/AFS automatic feeder: 24V DC, 1.5 A 90 - 264 V AC, 47-63 Hz, 0.75 A Matrix F32/F42: MF/MFD manual feeder: 24V DC, 1.2 A 90 - 264 V AC, 47-63 Hz, 0.
Frama Matrix F32/F42/F62 11.4.
Frama Matrix F32/F42/F62 Matrix F42/F32: Weight: 12 kg 11.5. Accessories See www.framashop.co.uk or speak to your local Frama Sales and Service partner.
Frama Matrix F32/F42/F62 11.6. Storage and operating conditions Frama Matrix F32/F42/F62 operating conditions Temperature range: 10°C – 40°C Relative air humidity: 10% – 80% (not condensing) Approved for use indoor only up to a maximum of 4000 metres above sea level.
Frama Matrix F32/F42/F62 12. EC-Declaration of Conformity in accordance with the EEC low-voltage directive 2006/95/EG in accordance with appendix III B; of December 12, 2006 Hereby we explain that those corresponds to below designated products in its conception and design as well as in circulation the execution the fundamental safety and health requirements of the Community directive low-voltage brought by us.
Frama Matrix F32/F42/F62 13. Index A Accessories ..................................................... 71 Admin mode ................................................... 56 Advertising imprint ........................................ 46 Advertising imprint text blocks ..................... 41 AF feeder......................................................... 33 Auto Log off .................................................... 54 Error messages ...............................................
Frama Matrix F32/F42/F62 Order accessories .......................................... 61 P PIN Code ......................................................... 54 Postage scales ................................................ 24 Power supply .................................................. 69 PP analogue .................................................... 43 PPI .................................................................... 43 PPI report.........................................................
Frama Matrix F32/F42/F62 Sales and service centre: Frama UK Limited, Hoddeston Questions on the operation of the franking system For problems with the connection; online system Help line: 01992 451 125 Ordering consumables: www.framashop.co.uk or your local Frama Sales and Service partner. www.frama.co.uk Frama AG CH-3438 Lauperswil Switzerland 76 Matrix F32/F42/F62 Document number 1019132 R03.