FFP S700 SERIES Pull-Out Spray Faucet Installation guide
ENGLISH G 1748.XX G 1782 G 1156 G 29016 G R0239.XX G 13396.XX G R0637 G R1664 G 1636 G 1463 TECHNICAL DATA · Minimum working pressure 0,5 bar · Maximum working pressure 5 bar · Recommended working pressure 3 bar (in case of water pressure higher than 5 bar it is recommended to install pressure reducers) · Maximum working temperature 70°C G 13396.XX G R0239.XX G 1156 G R0637 G R1664 G 1636 G 1463 G 1748.
ENGLISH Faucet installation lease remove all components from package and inspect prior to P installation (see itemized table and picture). NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit www.frankeksd.com 1 2 3 4 5 TABLE OF CONTENTS Faucet Fastening set (rubber washer, triangular flange, metal washer, nut) Counter weight and gaskets Spray head Valve-holder 1 2 3 4 Remove all mounting hardware from protecting plastic bag.
ENGLISH Install faucet to the sink or countertop Set the faucet into place on the sink as indicated in the figure. NOTE: the rubber O-ring should be sitting on top of the countertop and between the faucet body. DO NOT use putty or other sealant at this location.
ENGLISH Install faucet to the sink or countertop - follows 1 2 3 4 21 mm [13/16”] key Install the fastening components to the faucet’s threaded shank in the following sequence: O-ring (1), triangular flange (2), metal washer (3) and threaded nut (4) (the triangular flange can be omitted if the sink/countertop is too thick).
ENGLISH Attach the valve-holder 20 mm [13/16”] key Attach the valve-holder to the shorter tubing and attach the spray hose to the valve-holder. NOTE: The provided small black rubber washer needs to be installed here. DO NOT use putty or other sealant agents at this joint.
ENGLISH Connect the supply line 16 mm [5/8”] key Connect the supply line. In order to guarantee a long use of the product, install the angle valve equipped with filter and clean them regularly. Do not allow the supply tube to twist or bend sharply. Flush out debris from water lines and faucet. 1. Pull spray hose out of the faucet spout and point the open end towards the sink drain. 2. Open faucet handle - cold side first - by turning handle to the right and moving it upward 3.
ENGLISH Assemble Pull-out Spray Attach the pull-out spray head to the hose. NOTE: The rubber washer needs to be installed to prevent leakage. Fasten the weight to the hose as shown in picture below. Test all water lines, fitting and connections for leaks.
ENGLISH Replacing the cartridge B 2,5 mm [1/8”] Allen key A 28 mm [1-1/8”] key F E D C Before starting, shut off the water supply to the faucet and move the faucet handle to the off position. Use a 2.5mm [1/8”] Allen key to loosen the set screw (A) which is accessible from the back of the handle. Lift the handle (B) from the cartridge (F). Find the small notch at the base of the chrome ring cap and carefully pry up against this to remove the cap (C).
ENGLISH General maintenance Do not use harsh detergents, solvents, chemical agents, metallic sponges, etc. that could harm the surface. Clean only with a soft sponge and soapy water. Clean and then dry properly the faucet in case of very hard or calcareous water, whose deposits cold damage the surface.
ENGLISH Limited lifetime warranty Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the original purchaser of its faucets effective January 1, 2003. All faucets installed in a private residence will carry a limited lifetime warranty on all mechanical parts to be free of manufacturing defects in material and workmanship under normal usage.
