INSTALLATION GUIDE Little Butler® Hot Water Dispensing Faucets and Drinking Water Dispensing Faucets LB10100 Series DW10000 Series LB10200 Series LB11100 Series DW11000 Series LB11200 Series LB12100 Series DW12000 Series LB12200 Series Rev 3 - 6/25/2015 MAKE IT WONDERFUL
TECHNICAL DATA Pressure Range - MINIMUM 35 PSI - Recommended Maximum 75 PSI has certified that this faucet complies with NSF61 and NSF372 drinking water system component requirements. These requirements meet California Health and Safety Code requirements for low lead (AB1953) as well as the low lead requirements of the US Safe Drinking Water Act of 2014. INSTALLATION INSTRUCTIONS 1 Remove all contents from the package and check for completeness. NOTE: Call immediately if you see inconsistencies.
Installation Little Butler® Series Hot only Faucets (LB1 _100) Package Contents: 1 1 - Faucet (Item pictured may differ from faucet you have. See front cover for accurate illustration.
Installation 2 For best results, Franke recommends this faucet be installed by a licensed, professional plumber. The installer should familiarize themselves with how this dispensing faucet will be installed and function as part of a point-of-use water dispensing arrangement BEFORE the products are installed because there are several installation options. Make certain to observe all local plumbing and building codes during the installation.
Installation 3 It is recommended to take the components and locate their optimum positions before starting the installation. Make sure there is adequate clearance for the dispenser handle(s) to open fully without interference. Make sure all plumbing and electrical connections will reach the intended mounting positions for all the components and there will be no obstructions or sharp bends in plumbing. Make sure the counter top is no thicker than 2-¼”.
Installation 6 7 Install fastening set as shown: Rubber Washer, Metal Mounting Washer, Mounting Nut. Rubber Washer Metal Washer Mounting Nut Connect the cold water supply to the faucet: Mounting Nipple •Slide the plastic ferrule and the compression nut onto the blue ¼” poly-tubing and place the plastic insert in the end of the tubing as illustrated.
Installation 9 10 11 •Steps 9 – 15 pertain to connection of the LB1_100 and LB1_200 Series faucets •Remove the 3/8” compression nut from the factory installed steel supply hose.
Installation 12 Install Mounting Washer and Mounting Nut as shown. Mounting Washer Mounting Nut 13 14 15 Connect the black 3/8” poly-tubing from the faucet to the filtration system. If you decide not to utilize a filtration system with your LB1_100 series faucet, you must provide a connection for the black 3/8” poly-tube to the home’s cold water supply. Connect the high temp silicone tubing to the mounting nipple and secure the tubing using the hose clip.
Usage 1 2 3 Pull the handle(s) forward to turn on the water supply. Both valves will stay in the ‘on’ position until rotated back to upright position. Note: The spout has a 360° swivel capability WARNING! Do not operate both handles at the same time, as this can build up pressure in the heating tank causing the bladder to expand and eventually burst. Such damage is not covered by the warranty.
2 Replacement Parts Replacement Part # for Identified Part Model # LB10100 Series LB10200 Series DW10000 Series LB11100 Series LB11200 Series DW11000 Series LB12100 Series LB12200 Series DW12000 Series #1 #2 Cold Hot Cartridge Cartridge 5-022 5-022 5-022 5-022 5-022 5-022 - 5-021 5-021 5-021 5-021 5-021 5-021 #3 Handle Assembly Cold Hot 5-032* 5-023* 5-033* 5-024* 5-034* 5-025* 5-023* 5-032* 5-024* 5-033* 5-025* 5-034* - #4 #5 DW LB Series Series Mounting Mounting Kit Kit 5-027 5-027 5-027 5-02
WARRANTY Congratulations on the purchase of this Franke product! Franke is one of the world’s largest manufacturers of kitchen systems. Our products are manufactured using the highest degree of technology quality and design. As a result we are proud to offer the following warranty. Franke Inc. Kitchen Systems Division, warrants the quality of its water dispensing systems to be free from manufacturing defects for a period of five years from the date of purchase.
Franke Consumer Products Inc., Kitchen Systems Division 800 Aviation Parkway Smyrna, TN 37167 Phone: 1-800-626-5771 Fax: 1-888-685-0007 www.frankeksd.