Installation Instructions

ManualsBrandsFranke ManualsKitchen FaucetsFF6070A

KITCHEN

SYSTEMS

FF6000 . FF7000

INSTRUCTION MANUAL

Franke Consumer Products, Inc., Kitchen Systems Division extends the following

warranty to the original purchaser of its faucets effective January 1, 2003.

All faucets installed in a private residence will carry a limited lifetime warranty on all

mechanical parts to be free of manufacturing defects in material and workmanship

under normal usage. All chrome finishes carry a limited lifetime warranty; all other

finishes are warranted for five (5) years form the original date of purchase.

This warranty applies only to the original owner, providing the product has been

installed in accordance with our installation instructions, used as recommended and in

a normal residential application. In the event of a warranty claim, the owner will be

required to provide proof of purchase - save sales receipt. This warranty covers all

components which make the product operational. Franke, at its option, may repair or

replace the product or components necessary to restore the product to good working

condition. Franke reserves the right to inspect the installation prior to the actual

replacement of the product or component part.

This warranty does not cover misuse or abuse, accidental damages, scuffs or scratches,

improper installation, abnormal usage, negligence or damage caused by improper

maintenance or cleaning. Normal wear of parts is excluded from the warranty. Damage

caused by impurities or acts beyond our control are not covered. Any product or part

which has been repaired or altered in any manner outside of Franke's factory, unless

previously authorized in writing by Franke, will void warranty. Any replacement

excludes transportation and any labor re-installation costs. This warranty does not

allow recovery of incidental or consequential damages such as loss of use, delay,

property damage or other consequential damage, and Franke accepts no liability for

such damages.

The Franke warranty is limited to the above conditions and to the warranty period

specified herein and is exclusive. Franke DISCLAIMS all other warranties, expressed

or implied, including IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR

FITNESS FOR AS PARTICULAR PURPOSE. This warranty gives you specific legal

rights that may vary from state to state.

Further information

For any further information about our products, about the installation of them or about

the guarantee, please dial the number of the customer service:

Phone number +1-215-822-6590 Franke Consumer Products Inc. - Kitchen Systems Division

Or: 1-800-626-5771 3050 Campus Drive, Suite Hatfield, PA 19440

Fax number + 1-215-822-5873

8/8

LIMITED LIFETIME WARRANTY

InstallationGuide(Print)-FF6000&FF7000_I

Summary of content (4 pages)

PAGE 1
LIMITED LIFETIME WARRANTY Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the original purchaser of its faucets effective January 1, 2003. All faucets installed in a private residence will carry a limited lifetime warranty on all mechanical parts to be free of manufacturing defects in material and workmanship under normal usage.
PAGE 2
ENGLISH TECHNICAL DATA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Standard water flow 1.5 gpm - 45 PSI Maximum water flow 2.2 gpm - 60 PSI Recommended pressure range 25-100 PSI - Over 100 PSI PRV required Complies with Proposition 65, NSF 61, UPC and C-UPC requirements FAUCET INSTALLATION 1. Remove all contents from the package and check for completeness. NOTE: Product comes pre-assembled. NOTE: Call us immediately if you see inconsistencies. (1-800-626-5771) or visit www.frankeksd.com info.fks@franke.
PAGE 3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 10210 10211 10418 10698 3-019 * 3-020 * 3-033 3-034 * 3-047 3-048 92038 92037 10564 10406 * 10407 * 3-058 2. Flush pipe work to ensure it is free from debris. 3. Cut mounting holes 1 3/8" diameter (8” center-to-center spread requirement for faucet) in the desired position in sink. 4. Remove faucet and hardware from its protective packaging. Faucet comes assembled. 5. Detach hose fittings from tee body, temporarily remove locknut from diverting side. 6.
PAGE 4
14. Connect and tighten shorter supply hoses onto diverter-tee. Use open end wrench. 15. Next, install the sidespray assembly by installing rubber gasket & escutcheon flange along with base shank into 1-3/8” mounting hole. 16. From underneath the sink, install plastic mounting nut onto base shank until fully tightened. 17. Set sidespray into place. Insert spray hose into base.