OWNER’S MANUAL Model No. GZFI8013.7 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (inside tower) QUESTIONS? At FreeMotion Fitness, we are committed to providing complete customer satisfaction. If you have questions, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Visit our website at www.freemotionfitness.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ADJUSTMENT . . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all the important precautions and instructions in this manual and all warnings on the strength equipment before using the strength equipment. FreeMotion Fitness assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning this or any exercise program, consult your physician.
WARNING DECAL PLACEMENT The decals shown below have been placed on the strength equipment in the indicated locations. If a decal is missing or illegible, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decals may not be shown at actual size.
BEFORE YOU BEGIN Thank you for selecting the FREEMOTION® EPIC™ LEG EXTENSION strength equipment. The strength equipment features quality craftsmanship and an innovative design that will help your club members isolate individual muscle groups and reach their strength training goals. after reading this manual, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. To help us assist you, please note the product model number and serial number before contacting us.
ADJUSTMENT This section explains how to adjust the strength equipment. Make sure all parts are properly tightened each time the strength equipment is used. Replace any worn parts immediately. ADJUSTING THE RESISTANCE To change the amount of resistance for your workout, insert the weight pin into the desired weight. Make sure that the weight pin is fully inserted into the weight stack.
ADJUSTING THE BACKREST Backrest Adjustment Tube To move the backrest forward, slide the backrest adjustment tube to the desired position. To move the backrest backward, pull the tapered adjustment knob, slide the backrest adjustment tube to the desired position, and reengage the tapered adjustment knob. Make sure that the tapered adjustment knob is engaged in one of the adjustment holes in the backrest adjustment tube.
MAINTENANCE AND TROUBLESHOOTING For optimal performance of the strength equipment and to reduce the chances of injury to users, you must perform preventive maintenance on a regular basis. Instruct all personnel to perform the procedures described in this section. Personnel must also record and report any accident. To maintain the strength equipment’s warranty, use only FREEMOTION EPIC parts for repair or replacement.
Cable Traps Check the cable traps to ensure that they are not rubbing against the cables and that they are holding the cables in the grooves of the pulleys. If a cable trap is not correctly aligned, loosen the bolt slightly, readjust the cable trap as necessary, and retighten the bolt. there is not enough tension on the cables, the top weight will not be lifted immediately when the repetition is begun. Ideally, the cable should not move more than 1/2 in. (1.
Top Weight Adjustment Tools required: 5/32" hex key 1. If the cable needs to be shortened 3/4 in. (2 cm) or more, follow the instructions in steps 1 and 2 on page 9; then, go to step 2 below. 3. Pull the cable out of the top weight coupler. Determine the amount that the cable needs to be shortened, and cut that much off the end of the cable. The cable must be long enough to be held by the set screws without lifting the top weight. 2. Lift the coupler cover from the top weight coupler.
WEIGHT STACK SERVICING 9. Reattach the cable to the top weight coupler. Retighten the four set screws into the threaded holes. Tighten the set screws equally until they contact the cable. Then, tighten each screw alternately 1/4 turn, until all are set to 85 inch/pounds (9.6 Newton-meters). Servicing the weight stack involves replacing the two guide bushings and the weight insert in the top weight. To order these parts, see HOW TO CONTACT CUSTOMER CARE on the back cover of this manual. 1.
CABLE DIAGRAM The cable diagram shows the proper route of the cable. Use the diagram to make sure that the cable and the cable traps have been assembled correctly. If the cable has not been correctly routed, the strength equipment will not function properly and damage may occur. The numbers show the correct route of the cable. Make sure that the cable traps do not touch or bind the cable. 2 1 Tighten each screw alternately 1/4 turn, until all are set to 85 inch/pounds (9.6 Newton-meters).
PART LIST—Model No. GZFI8013.7 Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 11 5 1 33 2 2 1 2 2 1 1 6 4 2 1 2 3 2 2 10 3 1 1 1 1 2 4 4 1 3 1 2 Description R0208A Key No. Qty.
EXPLODED DRAWING—Model No. GZFI8013.
EXPLODED DRAWING—Model No. GZFI8013.
HOW TO CONTACT CUSTOMER CARE If you have questions after reading this manual, or if you require assistance, please contact Customer Care at the address and phone number listed below. Please be prepared to give the following information: • the MODEL NUMBER of the product (GZFI8013.
