User Manual
Table Of Contents
- 1 Introduction
- 2 Features
- 3 Transceiver description
- 4 System and power management
- 5 Radio Peripherals
- 6 MKW2xDxxxV operating modes
- 7 MKW2xDxxxV electrical characteristics
- 8 MCU Electrical characteristics
- 8.1 Maximum ratings
- 8.2 General
- 8.3 LVD and POR operating requirements
- 8.4 Switching specification
- 8.5 Core modules
- 8.6 Clock modules
- 8.7 Memories and memory interfaces
- 8.8 Analog
- 8.9 Communication interfaces
- 8.9.1 USB electrical specifications
- 8.9.2 USB DCD electrical specifications
- 8.9.3 VREG electrical specifications
- 8.9.4 DSPI switching specifications (limited voltate range)
- 8.9.5 DSPI switching specification (full voltage range)
- 8.9.6 Normal Run, Wait and Stop mode performance over the fulloperating voltage range
- 8.9.7 VLPR, VLPW, and VLPS mode performance over the full operating voltage range
- 9 Transceiver electrical characteristics
- 10 Crystal oscillator reference frequency
- 11 Pin assignments
- 12 Packaging information
MKW2xDxxxV Product Electrical Specification, Rev. 0.1
68 Freescale Semiconductor
9.2 AC electrical characteristics
Table 11. Receiver AC electrical characteristics
(VBATT, VDDINT=2.7 V, T
A
=25 °C, fref=32 MHz, unless otherwise noted)
Characteristic Symbol Min Typ Max Unit
Sensitivity for 1% packet error rate (PER) (–40 to +105 °C) SENSper — –99 –97 dBm
Sensitivity for 1% packet error rate (PER) (+25 °C) SENSper — –102 dBm
Saturation (maximum input level) SENSmax — +10 — dBm
Channel rejection for dual port mode (1% PER and desired signal –82 dBm)
+5 MHz (adjacent channel)
–5 MHz (adjacent channel)
+10 MHz (alternate channel)
–10 MHz (alternate channel)
>= 15 MHz
—
—
—
—
—
38
34
47
47
55
—
—
—
—
—
dB
dB
dB
dB
dB
Frequency error tolerance — — 200 kHz
Symbol rate error tolerance 80 — — ppm
Table 12. Transmitter AC electrical characteristics
(VBATT, VDDINT=2.7 V, T
A
=25°C, fref=32 MHz, unless otherwise noted)
Characteristic Symbol Min Typ Max Unit
Power spectral density
1
, absolute limit from –40C to +105C
1
[f-fc] > 3.5 MHz, average spectral power is measured in 100 kHz resolution BW.
–30 — — dBm
Power Spectral Density
2
, Relative limit from –40C to +105C
2
For the relative limit, the reference level is the highest reference power measured within 1 MHz of the carrier frequency
–20 — — dB
Nominal output power Pout –0.5 0 0.5 dBm
Maximum output power — 10 — dBm
Error vector magnitude EVM — 8 13 %
Output power control range
3
3
Measurement is at the package pin on the output of the Tx/Rx switch. It does not degrade more than 2 dB across
temperature and an additional 1 dB across all processes. Power adjustment will span nominally from –30 dBm to
+10 dBm in 21 steps @ 2 dBm / step.
—40—dB
Over the air data rate — 250 — kbps
2nd harmonic
4
4
Measured with output power set to nominal (0 dBm) and temperature @ 25°C. If trap filter is needed must meet reference
board size requirements.
—<-50<-40dBm
3rd harmonic
4
—<-50<-40dBm