User's Manual
Table Of Contents
- General Description
- Features
- Evaluation Kit Applications
- Revision Table
- Table of Contents
- List of Figures
- List of Tables
- Overview
- Installation and Setup
- Configuring Evaluation Kit Hardware
- Evaluation Kit Hardware Description
- PHY Evaluation Using the Wireless Developer Kit
- Summary List of Test Hardware and Software Required
- Equipment Handling
- Guidelines for Running Tests
- Transmit Spectral Mask Compliance Test
- Total Average Transmit Power Test
- Peak Envelope Power Test
- Receiver Sensitivity and Scaled Ranged Versus Throughput Tes
- Receiver Immunity Test
- Minimum Antenna Separation Test
- Penetration Test
- Video Transmission and Reception
- Operating Conditions and Characteristics
- Support
- FCC Compliance Statement
- License Agreement
- Warranty Disclaimer
- Glossary
- References
- Appendix A – Sources for Leasing of Test Equipment
Rev 1.34, June 2, 2004
Copyright © 2001-2004 Motorola, Inc. All rights reserved. Page 11 of 44
6. Respond No when prompted to create a new project.
7. Select Tools-> Programmer. A programming dialog box will appear.
8. Click the “Auto Detect” icon (third icon down on the vertical icon bar) on the
programming dialog to cause Quartus II to query for Altera devices via JTAG.
9. Quartus II should find 2 devices and display them in the programming dialog. One will be
an FPGA and the other will be an EPC16 configurator/Flash ROM. The EPC16/4/8 is
used on both the 1106 and 1116 boards from Motorola/XtremeSpectrum. The PC board
in a UWB Node is either an 1106 or an 1116.] The MC270141 device will be an EP1S40
on an 1116 board, or an EP20K1000C/E on an 1106 board. Note which FPGA device is
present.
10. The File column for each device should say “<none>.”
11. Right click on the top listed Device (EP1S40 or EP20K1000C/E ) to bring up a context
menu and select the “Change File…” entry.
12. Browse to the directory where the desired .sof and .pof files are located. Select dummy
file for the top (FPGA) device. The file name will be of the form dummy_xxxx.sof file
where xxxx is the number of the radio board type (either 1106 or 1116).
13. The second device should be Device EPC16/4/8
14. Right click on the second device ( EPC16/4/8) to display a context menu and select the
“Change File…” entry.
15. Select one of two .pof files based on whether an EP20K1000C/E (1106 board in the
UWB Node) or an EP1S40 (1116 board in the UWB Node) was listed in the
programming dialog. For an EP20K1000C/E FPGA use the file named
output_file_1000_tx.pof. For an EP1S40 FPGA, use the file named
output_file_S40_tx.pof .
16. Click on the Program/configure check box for both devices
17. Click on the Verify box for the EPC16/4/8.
18. Click the “Start Programming” icon (top icon on the vertical bar).
19. The response should indicate success at the bottom of the screen.
20. The status of programming will be updated continuously at the bottom of the Quartus
window. The programming process should take no longer than approximately three to
four minutes. When it completes successfully the status will read
Programming
Succeeded. If programming fails, reboot the Windows PC and cycle power on the
UWB Node then repeat steps 3 through 19.
Table 2: Summary of MC270141 Firmware Ugrade Files
Model XSUWBWDK Transceiver
EPC16 Config File FPGA Config File
dummy_1116.sof output_file_S40_tx.pof
3.2. Updating Evaluation Kit EEPROMs
Each model XSUWBWDK Transceiver contains an EEPROM used to configure its 1394
interface and another EEPROM used during MC270141 bootup. Each of these is discussed
briefly below.