User's Manual
Table Of Contents
- General Description
- Features
- Evaluation Kit Applications
- Revision Table
- Table of Contents
- List of Figures
- List of Tables
- Overview
- Installation and Setup
- Configuring Evaluation Kit Hardware
- Evaluation Kit Hardware Description
- PHY Evaluation Using the Wireless Developer Kit
- Summary List of Test Hardware and Software Required
- Equipment Handling
- Guidelines for Running Tests
- Transmit Spectral Mask Compliance Test
- Total Average Transmit Power Test
- Peak Envelope Power Test
- Receiver Sensitivity and Scaled Ranged Versus Throughput Tes
- Receiver Immunity Test
- Minimum Antenna Separation Test
- Penetration Test
- Video Transmission and Reception
- Operating Conditions and Characteristics
- Support
- FCC Compliance Statement
- License Agreement
- Warranty Disclaimer
- Glossary
- References
- Appendix A – Sources for Leasing of Test Equipment
Rev 1.31.4, June 2, 2004 Page 2 of 44
Revision Table
Rev Date Person Description
0.7 Aug 1, 2003 EHB Document redone to become combined SDK & transceiver User
Manual.
0.8 Aug 4, 2003 EHB Added DME, and video sender commands in sections 4.3.4 and 4.4.
4. Modified section 1.5, Linux Installation Procedures. Updated all
figures
0.9 Aug 15, 2003 EHB Corrected DME explanations. Removed DIP switch configuration.
0.9.2 Oct 5, 2003 EHB Corrected networking description. Added descriptions of recvfile,
sendchk, recvchk applications.
1.0 Oct 24, 2003 MSG Revised section describing SDK applications including sendfile,
recvfile, sendchk, recvchk, dme, stats, mode, config, etc.
1.1 Jan 30, 2004 MSG Placed descriptions of configuration and control utilities into
separate SDK Utilities Guide. Updated hardware description to
cover 1106- and 1116-based WEKs and added appropriate
diagrams. Added Motorola part numbers for WDK. Added to and
edited glossary and references sections.
1.2 Feb 5, 2004 MSG/EHB Changed XSI, XtremeSpectrum and associated terminology to
Motorola. Updated part numbers. Updated expected results in
sections Spectral Mask Compliance, Average Transmit Power, Peak
Envelope Power, and Video Transmission/Reception test sections.
Changed “FCC Non-Compliance Statement” section to “FCC
Compliance Statement” and updated the text.
1.3 June 2, 2004 MSG Updated firmware download description in section 3.1 to use
Quartus II Web edition. Corrected dme map_send_stream and
dme map_receive_stream syntax descriptions. Fixed usage of
mode and config commands (config works only in bridge mode)
in PHY evaluation procedures. Updated list of CE devices that work
with UWB Nodes. Corrected UWB chipset part numbers in Figure 3.
Assigned part number MC270141 to MAC FPGA. Suggested use of
a Motorola antenna in section 4.3 to assure FCC compliance. Added
ESIB to Table 3 and notes regarding frequency domain
measurements using the ESIB to section 5.4. Edited FCC
compliance statement. Added additional references to section 12.
Changed connector labels in Figure 1 & Figure 2 to reverse SMA,
1.4 July 23, 2004 MLS Corrected manual to comply with FCC written comments received
July 21, 2004. Section 4.3 was amended to allow use of only FCC
approved antennas with this product; confidential markings were
removed; the available software was re-verified to ensure device
may not operate any differently than what is approved (statement
also added in Section 8); a Declaration of Conformity (DOC) was
added to Section 8; complete calculation of the peak measurement
at the frequency of the highest emission (Fm, 4.1556 GHz) showing
all correction factors (antenna, distance ….) in the receiver for this
frequency was provided separately; and compliance with Section
15.517(a)5 was indicated in Section 4.1.