Reference Manual
Table Of Contents
- Preface
- 1. Introduction
- 2. Basic Radio Programming and Setup
- 2.1. Setting the Radio's Role in the Network and the Network Type
- 2.2. Establishing Communication with Instrumentation and Computers
- 2.3. Establishing Communication with Other Radios in the Network
- 2.4. Designate the RF Transmission Characteristics
- 2.4.1. 900MHz Channel Select Parameters
- 2.4.2. 900MHz Frequency Key (Golden Setting)
- 2.4.3. 900MHz Frequency Zones
- 2.4.4. High Noise
- 2.4.5. 900MHz Hop Frequency Offset
- 2.4.6. 900MHz Hop Table Size
- 2.4.7. 900MHz Hop Table Version
- 2.4.8. Max Packet Size and Min Packet Size (Golden Setting)
- 2.4.9. MCU Speed
- 2.4.10. Remote LED
- 2.4.11. Retry Time Out
- 2.4.12. RF Data Rate (Golden Setting)
- 2.4.13. RTS to CTS
- 2.4.14. Slave Security
- 2.4.15. Transmit Power
- 2.4.16. Transmit Rate
- 3. Configuring Point-to-MultiPoint Networks
- 3.1. Point to MultiPoint Network Characteristics
- 3.2. Point-to-MultiPoint Network Quick Start
- 3.3. Point-to-MultiPoint Operation LEDs
- 3.4. Overlapping MultiPoint Networks
- 3.5. Establishing Communication with Other Radios in a MultiPoint Network
- 3.6. Routing Communications through the Network
- 3.7. Setting Other MultiPoint Parameters
- 3.7.1. 1 PPS Enable Delay
- 3.7.2. Diagnostics
- 3.7.3. DTR Connect
- 3.7.4. Local Mode
- 3.7.5. Master Packet Repeat
- 3.7.6. Master Packet Repeat in MultiPoint Networks with Repeaters
- 3.7.7. Max Slave Retry
- 3.7.8. Radio ID
- 3.7.9. Radio Name
- 3.7.10. Repeaters
- 3.7.11. Repeater Frequency
- 3.7.12. Retry Odds
- 3.7.13. Slave / Repeater
- 3.8. Conserving Power
- 3.9. Reading Diagnostics in Tool Suite
- 4. Configuring Point-to-Point Networks
- 5. Advanced Programming
- 6. Viewing Radio Statistics
- 7. Approved Antennas
- 8. FGR3 Wireless Data Radios Pinouts
- 9. Troubleshooting
- 10. FGR3 Release Notes
- Appendix A: FGR3 Technical Specifications
- Appendix B: FGR3 Board Level Mechanical Drawing
- Appendix C: 900MHz Factory Default Settings
- Appendix D: 900MHz Channel Frequency IDs
- Appendix E: FreeWave Legal Information
FGR3
User-Reference Manual
Appendix C: 900MHz Factory Default Settings
900MHz Factory Default Settings
Operation Mode Default MultiPoint Parameters Default
Point-to-Point Slave 1 (0) Number of Repeaters 1
Set Baud Rate Default (1) Master Packet Repeat 2
Baud Rate 115200 (2) Max Slave Retry 9
(A) Data Parity 0 (3) Retry Odds 9
(B) Modbus RTU 0 (4) DTR Connect 0
(C) RS232/485 0 (5) Repeatr Frequency 0
(D) Setup Port 3 (6) Network ID 255
(E) Turn Off Delay / On Delay 0/0 (7) Reserved -
(F) Flow Control 0 (8) MultiMaster Sync 0
Radio Parameters Default (9) 1 PPS Enable Delay 255
(0) Freq Key 5 (A) Slave/Repeater 0
(0) Hop Table Version 0 (B) Diagnostics 0
(1) Hop Table Size 112 (C) Subnext ID “Disabled”
(2) Hop Freq Offset 0 Rx ID F
(3) Frequency Zone All 1s (Enabled) Tx ID F
(4) Government Rules 0 (D) Radio ID Not Set
(1) Max Packet Size 8 (E) Local Access 0
(2) Min Packet Size 9 (G) Radio Name "blank"
LUM0110AA Rev Jan-2019 Page 136 of 143 Copyright © 2019FreeWave
This document is subject to change without notice. This document is the property of FreeWave Technologies, Inc.
and contains proprietary information owned by FreeWave. This document cannot be reproduced in whole or in
part by any means without written permission from FreeWave Technologies, Inc.