Reference Manual
Table Of Contents
- Preface
- 1. Introduction
- 2. Basic Radio Programming and Setup
- 2.1. Setting the Radio's Role in the Network and the Network Type
- 2.2. Establishing Communication with Instrumentation and Computers
- 2.3. Establishing Communication with Other Radios in the Network
- 2.4. Designate the RF Transmission Characteristics
- 2.4.1. 900MHz Channel Select Parameters
- 2.4.2. 900MHz Frequency Key (Golden Setting)
- 2.4.3. 900MHz Frequency Zones
- 2.4.4. High Noise
- 2.4.5. 900MHz Hop Frequency Offset
- 2.4.6. 900MHz Hop Table Size
- 2.4.7. 900MHz Hop Table Version
- 2.4.8. Max Packet Size and Min Packet Size (Golden Setting)
- 2.4.9. MCU Speed
- 2.4.10. Remote LED
- 2.4.11. Retry Time Out
- 2.4.12. RF Data Rate (Golden Setting)
- 2.4.13. RTS to CTS
- 2.4.14. Slave Security
- 2.4.15. Transmit Power
- 2.4.16. Transmit Rate
- 3. Configuring Point-to-MultiPoint Networks
- 3.1. Point to MultiPoint Network Characteristics
- 3.2. Point-to-MultiPoint Network Quick Start
- 3.3. Point-to-MultiPoint Operation LEDs
- 3.4. Overlapping MultiPoint Networks
- 3.5. Establishing Communication with Other Radios in a MultiPoint Network
- 3.6. Routing Communications through the Network
- 3.7. Setting Other MultiPoint Parameters
- 3.7.1. 1 PPS Enable Delay
- 3.7.2. Diagnostics
- 3.7.3. DTR Connect
- 3.7.4. Local Mode
- 3.7.5. Master Packet Repeat
- 3.7.6. Master Packet Repeat in MultiPoint Networks with Repeaters
- 3.7.7. Max Slave Retry
- 3.7.8. Radio ID
- 3.7.9. Radio Name
- 3.7.10. Repeaters
- 3.7.11. Repeater Frequency
- 3.7.12. Retry Odds
- 3.7.13. Slave / Repeater
- 3.8. Conserving Power
- 3.9. Reading Diagnostics in Tool Suite
- 4. Configuring Point-to-Point Networks
- 5. Advanced Programming
- 6. Viewing Radio Statistics
- 7. Approved Antennas
- 8. FGR3 Wireless Data Radios Pinouts
- 9. Troubleshooting
- 10. FGR3 Release Notes
- Appendix A: FGR3 Technical Specifications
- Appendix B: FGR3 Board Level Mechanical Drawing
- Appendix C: 900MHz Factory Default Settings
- Appendix D: 900MHz Channel Frequency IDs
- Appendix E: FreeWave Legal Information
3. Configuring Point-to-MultiPoint Networks
FGR3
User-Reference Manual
LUM0110AA Rev Jan-2019 Page 85 of 143 Copyright © 2019FreeWave
This document is subject to change without notice. This document is the property of FreeWave Technologies, Inc.
and contains proprietary information owned by FreeWave. This document cannot be reproduced in whole or in
part by any means without written permission from FreeWave Technologies, Inc.
Low Power Mode
Setting Description
Default Setting 0
Options l Any number between 0 and 31.
l The higher the number, the greater the power consumption decrease.
Terminal Menu (3) Edit Radio TransmissionCharacteristics > (9) Low Power Mode
Description: Allows a MultiPoint Slave radio to consume less power, primarily by dimming the
radio's LEDs.
When set to 2 through 31, the radio sleeps between slots.
Example: Using a setting of 2 the radio sleeps 1 out of 2 slots.
Using a setting of 3 the radio sleeps 2 out of 3 slots, etc.
When the radio is asleep, it hears nothing from the Master.
This table shows the changes at different Low Power Mode settings.
l The actual current draw depends on many factors.
l The table gives only a qualitative indication of supply current savings.
l A low number reduces latency and a high number reduces current
consumption.
Setting Description
0 Low power, disabled.
1 l LEDs dimmed, radio remains awake.
l Radio is listening to the Master’s
transmissions on every slot.
l Radio’s data port is shut down if the
RTS line is de-asserted (low).
l In this case, the radio needs to be
awakened before it is able to send data
to the Master.
2 LEDs dimmed, radio sleeps every other
slot.
3 LEDs dimmed, radio sleeps 2 of 3 slots.
4-31 LEDs dimmed, radio sleeps the number of
slots corresponding to the setting.
Example: With a setting of 31 the
radio sleeps 30 of 31 slots.