User's Manual
Table Of Contents
- Preface
- 1. WP201-100 Overview
- 2. Installation and Setup
- 3. Configuring the WP201-100
- 4. Testing and Discovery
- 5. Backup, Restore, and Upgrade the WP201-100
- 5.1. Reset tab Procedures
- 5.2. Firmware window Procedures
- 5.3. Reboot the WP201-100
- 5.4. Restore the WP201-100 Factory Defaults
- 5.5. Restore to User Defaults
- 5.6. Backup WP201-100 Factory Settings
- 5.7. Backup the WP201-100 User Settings as the Default
- 5.8. Reset to the WP201-100 Defaults
- 5.9. Restore the WP201-100 to Factory New Settings
- 5.10. Restore the WP201-100 to the User Default
- 5.11. Upgrade the WP201-100 Firmware
- 6. Viewing Information
- 7. Administration
- 7.1. Changing the WP201-100 Account Password
- 7.2. Fast Roaming Activation
- 7.3. Guest Network Settings - Activate and Define
- 7.4. Define a Guest Network Security Mode
- 7.5. Define a WPA-Enterprise Security Mode
- 7.6. Define a WPA-PSK Security Mode
- 7.7. Email Alert - Activate and Define
- 7.8. Reboot Schedule - Activate and Define
- 7.9. Remote Log Activation
- 7.10. Set the WP201-100 Time
- 7.11. Setup IPv4 Static IP Settings
- 7.12. Setup of IPv6 Settings
- 7.13. SNMP Settings - Activate and Define
- 7.14. Spanning Tree Settings - Activate and Define
- 7.15. SSH and HTTPS Settings Activation
- 7.16. WiFi Scheduler - Activate and Define
- 7.17. Wireless MAC Filter - Activate and Define
- 7.18. Wireless Traffic Shaping - Activate and Define
- 7.19. Canceling Unsaved Changes in the WP201-100
- 8. Examples of WP201-100 Networks
- 9. WP201-100 Software Environment
- 9.1. WP201-100 Window Components
- 9.2. Account window
- 9.3. Advanced window
- 9.4. Basic window
- 9.5. Connections window
- 9.6. Device Status window
- 9.7. Firmware window
- 9.8. Log window
- 9.9. Reboot or Restore window
- 9.10. Site Survey window
- 9.11. Time Zone window
- 9.12. Tools window
- 9.13. Unsaved window
- 9.14. WiFi Scheduler window
- 9.15. Wireless window
- 9.15.1. Wireless Settings area
- 9.15.2. Operation Mode area
- 9.15.3. Wireless Settings area
- 9.15.4. Wireless Settings area - Operation Mode = WDS Station
- 9.15.5. Mesh and Mesh Advanced Settings areas
- 9.15.6. WDS Link Settings area
- 9.15.7. Guest Network Settings area
- 9.15.8. Fast Handover, Management VLAN Settings, and Cross Band VLAN Pass Through areas
- 9.16. Wireless Edit dialog box
- 9.17. Wireless Edit dialog box - WDS Station Mode
- 9.18. Wireless Edit dialog box - Guest Network
- 9.19. Microsoft® Enter name of file to save to dialog box
- 9.20. Microsoft® File Upload dialog box
- 9.21. Microsoft® Opening Backup dialog box
- 10. WP201-100 CLI List
- 11. WP201-100 Factory Defaults
- 12. WP201-100 Release Notes
- 13. WaveProWP201-100 IP Address Recovery
- Appendix A: WP201-100 Technical Specifications
- Appendix B: WP201-100 Available Accessories
- Appendix C: FreeWave Legal Information
WavePro™ WP201 Access Point: User Manual
Table of Contents
Preface 8
1. WP201-100 Overview 10
1.1. Assumptions 11
1.2. WP201-100 Included Equipment 11
1.3. User-supplied Equipment 13
1.4. WP201-100 Hardware Layout 14
1.4.1. Front of the WP201-100 14
1.4.2. Back of the WP201-100 15
1.4.3. Left Side of the WP201-100 16
1.4.4. Bottom of the WP201-100 16
1.4.5. Right Side of the WP201-100 17
2. Installation and Setup 18
2.1. Connect to the WP201-100 Access Point 19
2.2. Setup the Computer IP Address Configuration 21
2.3. Access the WP201-100 24
2.4. Change the Wireless Mode 25
2.5. Wall Mounting Installation - WP201-100 28
2.6. Pole Mounting Installation - WP201-100 32
2.6.1. Included Equipment 32
2.6.2. User Supplied Equipment 32
3. Configuring the WP201-100 36
3.1. Access Point Configuration 37
3.2. Mesh-AP or Mesh-Only Configuration 42
3.3. WDS - Access Point Configuration 48
3.4. WDS - Bridge Configuration 55
3.5. WDS - Station Configuration 61
4. Testing and Discovery 66
4.1. Discover Devices Connected to the WP201-100 67
4.2. Run a Ping Test 68
4.3. Run a Speed Test 69
4.4. Run a Traceroute Test 70
5. Backup, Restore, and Upgrade the WP201-100 71
5.1. Reset tab Procedures 71
5.2. Firmware window Procedures 71
5.3. Reboot the WP201-100 72
5.4. Restore the WP201-100 Factory Defaults 73
5.5. Restore to User Defaults 75
5.6. Backup WP201-100 Factory Settings 76
LUM0073AA Rev Feb-2017 Page 3 of 267
This document is the property of FreeWave Technologies, Inc. and contains proprietary information owned by
FreeWave. This document cannot be reproduced in whole or in part by any means without written permission from
FreeWave Technologies, Inc.
DRAFT