BAe HAWK T.'1 WIN 1 AL m J USER MANUAL WINGSPAN: 'I D20MM(40.'16 ") LENGTH: '122'1 MM (4B.'I ") EMPTY WEIGHT: '1450G cw O BATTERY) FCCE®�!O •• ::a (!] (!l . www.sz-freew1ng.
Introduction Perhaps the most versatile British advanced trainer jet in the world, the BAe Hawk has been in service for over 40 years. Operated at its peak by 18 countries in various trainer and light combat roles, the Hawk T1 variant was also popularized by the Red Arrows display team, whose expert piloting demonstrations have amazed audiences worldwide for generations. Freewing and Motion RC are proud to present this well-loved aircraft as a 70mm EDF powered electric flying model.
Product basic information Standard version Wing loading:97.5g/dm2 Motor: 3048-2300KV brushless outrunner motor Ducted fan: 70mm 12-blade fan ESC : BOA brushless Servo: 9g digital metal gear servo(Bpcs) Flight speed : 160KPH/100MPH Empty Weight: 1450g(without battery) Thrust: 2300g 0 'q' E E 0 N 0 l Other features 1221mm{48.
PNP Assembly Instructions EN Traction steel wire Our tests show that excessively long servo extension lines increase the rise of poor connections that can lead to servo brown outs or failure, causing accidents during flight. Instead, this kit contains a steel wire that can be used to pull the main wing/elevator and rudder servo wires through the airplane to the battery compartment, eliminating the need for extension wires. Horizontal Stabilizer Assembly As shown in the photo below: 1.
PNP Assembly Instructions EN Main Wing Installation Step@ B- Main wing servo cable C- Screws (PA2.6x10x4pcs) As shown in the photo: 1.lnsert the aileron servo cable into the battery compartment and place the main wing on the fuselage. 2.Use 4 screws to attac h. Do not over tighten! StepO Scale Accessories Installation Pitot tube -� Note: After completing the above steps, insert each servo cable into its corresponding location on the labeled control board.
PNP Assembly Instructions Pushrod instructions Flap pushrod mounting hole Flap pushrod size Pushrod diameter Ø1.5mm 86mm (3-3/8") 1 2 3 4 Pushrod diameter Ø1.5mm (2-3/16") 1 2 3 4 2 3 Elevator pushrod mounting hole Elevator pushrod size Pushrod diameter Ø1.5mm 67. 8mm (2-11/16") 1 2 3 4 2 3 Rudder pushrod mounting hole Rudder pushrod size 55mm 3 Aileron pushrod mounting hole Aileron pushrod size 55mm 2 Pushrod diameter Ø1.
PNP Assembly Instructions EN Battery Size Battery hatch Use rubberized non-slip tape or Velcro Battery compartment size: L=117 W=63 H=47(mm) Before connecting the battery to the ESC, switch on the transmitter power and make sure the throttle stick is in the lowest position. Engage the ki ll swi tch i f one i s assi gned. Bind your receiver to your transmitter according to your transmitter's instruction manual. • iiii We recommend the following Li Po battery: 6S 22.2V 2600mAh - 6S 22.
PNP Assembly Instructions EN Servo Direction 2000 IJS 2000 IJS The servo positive or reverse rotation is defined as follows: : When servo input signal change from 1 000µs to 2000µs, : The servo arm is rotated clockwise, its positive servo. The servo arm is rotated counterclockwise, its reverse servo. If you decide to use a different brand of servo, check with the chart below to ensure that it is compatible with the airplane. Servo regulation No . Pos./Rev.
PNP Assembly Instructions EN Directional Control Test After the build is complete, power up the radio, ensure the throttle is in the lowest position, engage the kill switch if one is assigned and connect a fully charged battery to the ESC. Use the radio to ensure correct control direction. Aileron •-- - - Stick Left � Elevator - Stick Back � Stick Forward Stick Left Stick Right �Ill • - Flaps down BAe HA\NK T. 'IA Item No.
PNP Assembly Instructions EN •·dihtitti According to our test results, the following rates proved to be a good starting point. Low rates are good for initial flights or less experienced pilots. High Rates will be more sensitive to control inputs. Program your preferred Exponential % and the following rates. After initial flights, adjust the rates to suit your own style.
Dongguan Freewing Electronic Technology Ltd HK Freewing Model International Limited Add.:FeiYi Building.face to Labor Bureau, Fumin Middle Road, Dalang Town, Dongguan City , Guangdong Province, China Web: http://www.sz-freewing.com Email:freewing@sz-freewing.com Fax:86-769-82033233 Tel: 86-769-82669669 *�"$"tJt�-=ff4!1��&0§J � � "t JI*�� 00 �ffi � �& 0 §J :1:-lR:l:Jl:: , *� *%m*M� I'� ��402-408% �Ji:li[Y:li Web: http://www.sz-freewing.com Email:freewing@sz-freewing.
