Uncatalogued Product Introduction Assemble Instruction Preparation for the flight Center of Gravity 3D Mode Mix Set Assemble Structure El HEN Meg TEEN
Welcome to purchase our new EDF jet S8U35. SUSS/ Su Kai 35 ( NATO code name: Flanker-E } ) is the 4.5 generation of heavy fighters, with remote, multipurpose, air superiority and strike characteristics.
Accessory Bag Content List Main wing plastic parts bag Spare parts bag 1 No. Name Specification | Qty. No. Name Specification | Qty. 1 Screw PM4*14mm 4 1 Clovis ! 2 2 Screw 4 2 Screw / 2 3 Total wire | 67.8.7mm #1.2mm 2 3 Female load / 2 4 Rudder arm / 2 4 Casing ! 2 5 underarm pressed / 2 5 [Elevator ball arm I 1 6 Rudder ball arm ! 1 Elevator plastic parts bag 7 Ball buckle I 2 No. Name Specification | Qty.
ERMA AHH PM4*14mm €1. 2mm 2 3 FRE 2 4 REAR me Rarer / 2 5 FRE 1 6 THRU 1 TIRE 7 HLH EARN 1 1 we 2 4 Ae REM 0.204 —MFMZA, 2 #242 5 Me €1. 5mm ERE / 2 1 BEEPER 2 7 | ASSAMESE / 2 2 RHR 1 8 BEE €16%123mm 2 3 BEER 1 HEMMER PA3*25mm 2 2 ne PA3"30mm 2 3 We 4 4 He €1.
Install Note: 1.When Install, please read the manual carefully. If you have any questions, kindly contact with your distributor, or contact us on 2.the manual was based on the 3D sport version as a reference, part of the contents is not fit the standard version. Hr 1 HEME, GANGRENE, WHERE, TERR BEEN, BERNARD Die BRUISERS HB ELEM Ck RCE LE Install Arm 1, Please prepare the following parts to Install the arms as the right photo shown.
5. Pleass refer to the right photo after installation. CEREBRATE EER Install Elevator 6. Pleasa prepare install accessories. PRL 6. MEF REF HRA. 7.Put the metal fasteners into the groove, the screw upward. Then through the carbon stick as the right photo shown. WEEPER, AGREEABLY, Rent, | FERAL. 8. Screw carbon tube tightly. 9. Insert the stabilizer carbon tube into fuselage as the right photo shown. 9. WEE TR HRH RIBS AH BF REAL.
10. Turn stabilizer up and down and confirm its install is correct,then screw carbon tube in fuselage. 10. HEATPROOF, BARKERS, ARLENE ABLE STREET. 11.After install, push and pull the elevator, if any gap, we can unlock the metal fasteners in elevator, adjust the fix piece to solve. s AER. WREATH of LUA 12.Refer to the right photo after finish installation. 12. REMEMBER EF. 13.Insert the control wire into servo arm. 13. Resume EF ABNER.
15.Refer to the right picture, glue these area. 16. WA EF, EIR A REAR. 16.Stick the plane belly vertical fixed wing. 16. BRIER RR. 17.At last,buckle plastic clip to stabler arm. 17. 8G, BEHKLAANTFRBEAInstall Main Wing 18.prepare install accessories. IRE 18. Media SRB REA. 19.0pen fuselage wing mounting paper tape. Pull out the main connection line. 19. HFS REMEMBER A. Hh ERE.
20.To distinguish left and right wing, connect the wing servo line and fuselage line. nd ny iv void ever: 20. STRAFE, OVERCOMPENSATE REFERRER. GEE, WERXSRXMEE. EAE, HERE) 21.Insert the man wing stainless steel tube Into the body of stainless steel tube in. At the same time, servo line along the fuselage slot into it. FHS TEA TERN. Ff, 22 After install, please refer to the right photo. 22.58 RE WA EHR. 23.In here lock into a screw to fix wing. = \ screwed tightly, Because there may be inserted into the the I
30.Glue on AB glue. 30. FELIX FIR ABBR 31.Glue and Install well the PVC slot cover. 31. Cermet AE. Install Nose Cone And Tail Cone 32.Nose cone install accessories. Blk. REAL 32. Femaleness. 33.Refer ta the right photo, glue ane fleece foam of nose cone. 33. MAE, ERB —SCHEHERAZADE ERIK. 34.Gluing two part of the nose cone. 34. Hemlock-MRER AER.
35.Then glue nose cone refer to the right picture. 35. BAA ALE RAR AK 36.Attached to the body. 36. MES. 37.Please refer to right photo after finish install. 37. SERRA BFR. 38.Glue the adhesive surface of tail cone. 38. BEEN THY IRK. 39.Refer to the right photo, glue to fuselage. When glue process,we should use hand fix it 3-5 minutes until fastening. 39. BARTER HEARSE. HALEY, RN TEATFEEANI-S46, HEBERT.
Prepare Before Flying Channel Introduce Channel set, please refer to the following list : ERR A FIDEL SARA WEE RESET SE UTAH: Standard Version 3D sport Version BR BR Aileron Aileron FRE FRE Elevator Elevator Clr ARG 6) Rudder Rudder (nose landing gear steering ) (nose landing gear steering and rudder servo control) Hil Throttle He EER EER Gear Gear Ji dik — (P88 Vector 1 (vector left and right control) (mE) Vector 2 (right vector up and down control) TE = (Gem LF Ea) Vector 3 {left vector up and down contro
SEE — (REIFY NRT) 5. Mixing 1{vector 1 mixing to Rudder channel) Tangibility md BULL q =n a Lar HH Hos oa 6H (ME REF REN) 6. Mixing 2{vector 2 mixing to Elevator) ) E THIEF tT intent at TREE (RIME EEE) 7. Mixing 3(vector 3 mixing to Elevator) Hil GER sod ld SEEN (MERIDIAN 8. Mixing 4(vector 2 mixing to Aileron) SLEET (WER=RHEIIH 9.
BE, BERN, HEARTHRUG BERT ERA. In end, after set, test its set is correct and effective. LIEBERMAN, FRATERNITY, H REO A TEs. Switch on mixing mode, when elevator move down, at the same time, vector move down. 2.5 FRE LES, WE OVERLIE Ex. when elevator move up,at the same time, vector move up. 3.47 ARE EARN, REO REFREEZE. when rudder move left,at the same time, actor move left ALF RARE RAR, LARDNER. when rudder move right, at the same time, vector move left. 5. AF, BEER, ZERO SERGE Hie.
HR THERMOMETER, EEC, BRARELREAMBETRE, SED THE SEEN, FF HRA WILDCAT. MARKETEER, RIGHT WEARER. UA, CHEERFULNESS. WRESTLER. T BARRE, HA, SU-3SKDKTRLEEBEMMEARTIR. Note 1.After complete above work, before flying, we advise you use small servo size flying, after fully know the airplane characteristics,then start the passion of 3D flying. 2.
