introduction Thanks for your purchasing our Freeing “Stinger 80°. iris a new 90mm EDF sport Jet, we revised iron the basis of Stinger 64's shape. Stinger 90 used many excellent design, seamless flap design and seamless aileron design, let ths foam surface looks more clean and beautiful. 17g metal gear servos, new surface control horns and cavils, let the surface control mots precise and stable. New multi-prophesier dusted fan, can produce more thrust and better voice.
Product basic information # Motor A748-1450KY # ESC 100A EBC weakness; # Serve By Metal Gear Servos (pee) 17g Metal Gear Servos (pes) 4 Battery 68 22.2V 5000mAh 35C 18 3.7V 480mAh 25C (pea Use for Led Lights) ¢ Dusted Fans 80mm EDF ¥ Take-off weight 28009 {98.8 02.) (enfranchising Battery 22.29 S000mAR 3850) (52, 17 In} 1325 mm ¢ Thrust 3200g {113 02.) 1130 mm (44.
Installing the Wing Remove these accessories A Fuselage Birthright wing C Carbon tube D Screw su E Screw ox Fe Y-wire 1. Insert the carbon tube (Clint fuselage. 2. Inge rt the left/right wing info together. 3. Screw tightly by serenade. 4. Connect the aileron servos by Y wire{F}. Connect the flap serves by ¥ wirehair. §. As the right photo shown, along the arrow direction ,Y wire {F) penetrates from the fuselage{G) Into canopy. 8. install the main wing on tha fuselage and fix it by 4 screws(E}.
installing the Elevator Removes thaws accessories and continuous to install. A The fuselage which installed on the wing B Elevator C-Brew pass som ween Oe 1.Connect the elevator serves cable {0} by Wire (E). 2.Install the elevator in the fuselage. When install the elevator, you should insert the extra long serve cable into the trough (F} of fuselage. 3.Fixed the savior by screws {C }.
installing the rudder Remove theses accessories. A Fuselage B~ Rudder Corkscrew swan soon 1. Connsct the rudder larva cable {F} and intentional wire (3) in fuselage. 2.Install the rudder on the fuselage. When install the rudder, you should insert the extra long servo cable anti the trough (GQ) of fussiness. E rages 20s 3.install the *V” shape rudder plastic part {C jon the rudder. 4. Fixed the lavatory by screws (E } {D). installing nose cone Wa prepared two pes nose cone for you.
Ina tailing nose landing gear Usually, before ship, the factory installed all the landing gear. in here, we also need io provide mots desalt installation and spare parts name. Players can refer if to revise and replace parts.
installing rear landing gear Rear landing gear spare part fist: Ac Landing gear J -Irtish ate relating am Keenan! shalt Jimmie new I -Hast McFarland goat W-Gasket mats wit Hal sore D-Rearguard gear O-Rene ding gear on sin strut stalked sot E-Sower P-Rear gait mount Fed ping Q-Sere G-Rear landing gear blister draping sere lover pace H-Bin Rear landing gear oi bin over 1 Insert the rear landing gear metal wire {C} into landing gear relating arm (A) and fix it by apes Mimi soreness. 2.
installing the servo of Elevator 1.Apply glue on the indicated area as the right photo shown, and attach the 17g servo bax { A) and control horn (8) on the main wing. 2 Press the 17g serve on the servo box (A), and preach the serve cable {I} on the trough (CG) of main wing. 3.Put te servo cover (E) on the serve box (A) and fix it by Zoos screws(F}. 4.Connect the serve arm and control horn by serve push rod {H). &.Canter the servo arm. 8. Uss the same way to Install another elevator servo and rudder serve.
Install on battery Canny Lift op taps, it ~~ removable canopy Lift up tape, it removable canopy, then bundled battery with Velcro, Before connect battery and receiver, please switch on the transmitter and check that the thrombosis is in the low position. Our standard battery is: 88 22.2V 5080mah 38C You can choose the battery refer to the battery cabin size: L=180mm; W=80mm; H=4Bmm = 68 22.
install powerless uninstalled the motor (D) In the dusted fan cover {C). 5. Finatly Install the fan cow! (A) on the bottom of 2.Fixed it with apes cup head screws (B). dusted fan cover (C) and fix i with 2 pos Mimi screws 3.Put the fan (E} into motor shaft. { please note the {H). plat position of hardware which installed in the fan, 8. Connsct the motor and ESC in fuss lags. and the plat position of motor shaft, please check the 7. Putthe installed Heedful} in the fuselage (K).
install powerless 1.installed the motor (A) In the dusted fan cover (B). 8.Finally install the fan cow! {A} on the bottom of 2. Fizad It with SPCA cup head screws (0). dusted fan cover {(C) and fix it with 2 pos Mimi 3.Put the clip {E} inch motor shaft and use apes Mimi screws {H). screws{D} to fix the slip (E}. 7.Connect the motor and ESC in fuselage. 4.Put the fan (F) into the clip (E) .{ please notch the 8.Put the installed EDIFY} in the fuselage. plat position of hardware which installed in the fan, 9.
Control direction lest After installed the plane, before flying, we need a fully charged battery and connect to the ESC, then use radio to test and check that every control surfaces work properly.
Troubleshooting Guide Marat doss not turn on A} Li-Po battery depleted B} Transmitter battles depleted ©) Transmitter not turreted on A) Recharge Li-Po battery 8) Rapists or recharge batteries ©) Tum on transmitter Dj Li-PS be fiery nol plugged in 3) Plugin Li-Po bestiary E} Motor not armed E} Arm motor F} Crash has damaged an maintain component 8} £8C or other damaged £) Replace 5) Chick ESC or contact local distributor Cub is difficult be control A} You ars flying in tao mush wind 8} Li-Po battery deplete
Accessories list support tom Mo. Prudish mama Specification nit) Oy | | loam Np.
XE ERE% .
