) FMCO012436/013036/013636/014836 & | MEDICINE CABINET INSTALLATION GUIDE FRESCO IMPORTANT SAFETY INSTRUCTIONS When using an electrical furnishing, basic precautions should always be followed, including the following: \ | READ AND FOLLOW ALL . DANGER | INSTRUCTIONS BEFORE | USING THIS CABINET. > WARNING 7o reduce the risk of burns, fire, electric shock or injury to persons. Use this furnishing only for its intended use as described in these instructions.
) FMCO012436/013036/013636/014836 & | MEDICINE CABINET INSTALLATION GUIDE FRESCO TOOLS REQUIRED FOR ASSEMBLY o Single Double Door Door Cabinet Cabinet Shelf Clip Bottom Screw Cap Hole Plug Mounting 123 Mounting {0514 G805 Bracket Bracket 0 ol (2/3) {3 Hinge Screw Wire Nut a @18 74y & Glass Shelf Glass Side Panel &3 o @ FMC012436/013036/013636/014836 | INSTALLATION GUIDE ©2018 FRESCA™ All rights reserved.
) FMCO012436/013036/013636/014836 & MEDICINE CABINET INSTALLATION GUIDE FRESCO DIMENSIONS A Cabinet’s Width B Cabinet’s Height € Cabinet’s Depth NOTE: Determine overall medicine cabinet dimensions. If recessing medicine cabinet, determine rough-in dimensions. 225"x 344" | | 344" x 344" | 461" x 34.4" *All dimensions & specifications are approximate and subject to change without notice. @ FMC012436/013036/013636/014836 | INSTALLATION GUIDE ©2018 FRESCA™ All rights reserved.
PRIOR TO MOUNTING: Remove Door/s Prior mounting your cabinet. Start with unplugging the door from the cabinet. ILLUSTRATION 2A @ FMC012436/013036/013636/014836 | INSTALLATION GUIDE ©2018 FRESCA™ All rights reserved. This material may not be reproduced, displayed, modified or distributed without the express prior written permission of the copyright holder.
) FMCO012436/013036/013636/014836 & MEDICINE CABINET INSTALLATION GUIDE FRESCO ELECTRIC CONNECTIONS ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENSED ELECTRICIAN @ WARNING: shut off power before wiring the cabinet. WARNING: An Electrical option cabinet must be wired to a 20 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.
Draw the perimeter of the medicine cabinet on the wall. RECESS-MOUNT INSTALLATION Cut the marked perimeter with appropriate tool. Frame the cutout opening. (See illustration below) Level, then secure the medicine cabinet with the screws through the mounting holes into the framing studs. Place and hold the medicine cabinet in the cutout opening. 4 STEPS TO FRAME THE CUTOUT OPENING 7 GLASS SHELF INSTALLATION RN Choose the position for your shelves, then push and twist the pins into place. a.
SURFACE-MOUNT INSTALLATION Level and mark the medicine cabinet’s location on the wall from point a to point b. IMPORTANT: Bottom mounting brackets must be attached to furring strip/channel or wall studs. Attach bottom Level and mark. bracket (E) to Insert top mounting bracket (D) into the top of the cabinet (A). With assistance, rest the medicine cabinet (A) on the bottom mounting bracket (E) and hold it in place. IMPORTANT: Top mounting brackets must be attached to furring strip/channel or wall studs.
SURFACE-MOUNT INSTALLATION NOTE: For more details on the shelf Connect the glass shelves (C) to the cabinet by pushing the side of the shelf in the left or right clip and snapping the shelf down. IMPORTANT: Top mounting brackets Slide top brackets into channel Make sure top brackets are must be attached to furring at the top of the cabinet. locked in the grooves. strip/channel or wall studs. IMPORTANT: | Test the fit of the cabinet Make sure cabinet is leveled before Final assembly.
FINAL ASSEMBLY Slide the doors into place by pinching the end of the hinge. Plug the door into the cabinet. %@w Insert clear snap in shelf 3‘%& Push the side of the shelf (C) fifiic Insert clear plugs (H) into the clips (F) into holes on the in the left or right clip and remaining or unused holes, then cover sides of the cabinet (A). snap the shelf (C) down. screw heads with the screw cups (G). FMC012436/013036/013636/014836 | INSTALLATION GUIDE ©2018 FRESCA™ All rights reserved.
L FINAL ASSEMBLY How to use Defogger Switch and Dimmer Switch: Touch the Defogger switch to turn the heating coils on or off. Touch the Dimmer switch to turn the task light on or off. Press and hold the dimmer switch to dim or brighten the task lights. Dimmer switch stores the current light level intensity when switched off and on. How to set your Digital Clock: Press and hold the button on the side of the door Press the side button again while the for two seconds to enter programming mode.