Install Instructions

APCO® Whole-house air puriers reduce odor-causing and potentially toxic VOCs, as
well as biological contaminants including mold, bacteria, viruses, and allergens in
indoor air. This award-winning technology uses a unique combination UV-C light and
activated carbon cells to clean the air.
INSTALLATION INSTRUCTIONS
FAMILY OF
WHOLE-HOUSE
AIR PURIFIERS
IMPORTANT!
• Only qualified technicians should install this product*
• Install in accordance with relevant building codes
• Read instructions carefully including safety warnings
WARNING!
PROTECT EYES FROM UV LIGHT
TURN OFF UNIT OR DISCONNECT
BEFORE SERVICING
© Fresh-Aire UV
*Installation of this product by anyone other than licensed HVAC or electrical contractors voids warranty.
US patent #7,704,463
RT Standard MAG15 MAG11
Air Handler
Optional
2nd UV Lamp
Filter media
Furnace
Optional
2nd UV
Lamp
Humidier
APCO in return duct with
light shining away from
lter media
APCO is usually installed on the supply side
duct just above the air system (upstream of a
humidier). It can also be installed on the return
side if necessary.
Orient so the air ows past the UV light rst
before the carbon. Position the unit so the UV
light does not shine directly on non-uv-resistant
materials (lters, humidiers, ex duct, etc.).
Ideally the UV light shines on the coil.
For dual systems select a remote UV light
location that shines on the greatest surface area
or the area with the most microbial growth.
Refer to the Optional Remote UV Light section
for installation instructions.
Typical Installation Locations
Standard APCO Installation
See back page for lamp replacement Info
Standard APCO Parts List
A
Main Unit
B
In-Duct Air Purif ier
Power Cord (ER Model)
C
Duct Mount Plate
D
Duct Mount Gasket
Small Parts
E
Self-tapping Screws
F
Machine Screws
(for cover)
G
Quick Nut (plastic)
H
Tap-in Connector
I
Spade Connector
UV Lamps
J
PART: TUVL-115 LIFE: 1 Year
K
PART: TUVL-215 LIFE: 2 Year
Optional 2nd UV Light (Dual)
V
PART: TUVL-115P LIFE: 1 Year
W
PART: TUVL-215P LIFE: 2 Year
X
WARNING
Panelsticker
Y
WARNING
Sight Glass
Z
Magnet mount
1. Use gasket
D
to trace cut-line onto duct.
2. Cut hole in sheet metal or duct board.
IMPORTANT! Remove and dispose of
cut-out piece of material.
3. For sheet metal duct secure mounting plate
C
to
sheet metal ducts using self-tapping screws
E
.*
4. Remove paper backing from one side of gasket
and x gasket to the back of the mounting plate.
5. Remove paper backing from back of gasket then
x mounting plate and gasket to the duct.
6. Bend mounting plate anges around the edges of
the hole to secure mounting plate. For duct board
use tape on edges of mounting plate for air leaks
and additional hold.
STEP 1: Standard APCO Duct Mounting
1.
4.
2.
5. 6a. 6b.
3.
* To install without backing plate use (4) self-tapping screws.
STEP 2: Standard APCO Power Unit & UV Lamp Mounting
1.
4. 2. 3.
1. Fit the APCO® Main Unit through hole in duct.
If attaching directly to metal duct use (4) Self-
tapping Screws. If the Backing Plate is used t the
unit over the threaded posts and use (4) Quick
Nuts
G
to secure it.
2. Insert UV Lamp.
3. Mount UV Lamp using (2) Quick Nuts and
attach lamp connector (be sure to align the four
connector pins).
4. Attach the cover with machine screws
F
.
J K
or
G
G
F
STEP 3: Standard APCO Connecting to Power
IMPORTANT
Before connecting to power conrm which APCO model is being installed. Turn o main
power source before installation. Always use proper conduit ttings and terminations.
Model information is printed on the Power Unit cover.
IMPORTANT! Must be wired to constant power - do not connect to blower relay.
Connect to load side of HVAC
Connect to load side of 24 VAC transformer
APCO
ER/DER
APCO
SI/DI
120-277 VAC
POWER SUPPLY
UV LAMP
4 PIN
CONNECTOR
L1 - BLACK
L2 or N - WHITE
GND - GREEN
Optional 2nd UV Lamp
24 VAC
POWER SUPPLY
UV LAMP
BLACKBLACK
4 PIN
CONNECTOR
REDWHITE STRIPE
24 VAC TRANSFORMER
COMMON / BLUE
HOT / RED
Connector
Optional 2nd UV Lamp