Blue-Tube XL Owners Manual

ManualsBrandsFresh-aire ManualsAir PurificationBlue-Tube XL Dual Lamp UV System - 32" - 2 Year Lamp

Parts Included

UV Lamp(s) 2 Year

Lamp Cable

Sheet-metal Screws

½” Pipe Straps

½” EMT Tubing (40” length)

1 piece per lamp

Power Supply(s) 10” * (magnet mount)

Power Supply(s) 14” ** (magnet mount)

Lamp Clip/Conduit Clamps

½” Pipe Couplings

UV Warning Sticker

Black Nylon Zip-Ties

Power Supply Magnets

Bracket Magnets

Sight Glass

L - Mounting Brackets

12” Stand-o

IMPORTANT!

• Only qualified technicians should install this product*

• Install in accordance with relevant building codes

• Read instructions carefully including safety warnings

WARNING

PROTECT EYES FROM UV LIGHT

TURN OFF UNIT OR DISCONNECT

BEFORE SERVICING

O P

WARNING

BLUE-TUBE XL™ is designed for installation into commercial air handling

units and rooftop package units for the purpose of surface or airborne

disinfection using ultraviolet germicidal irradiation. For maximum

installation exibility and cost-eectiveness the UV lamps are mounted

onto a framework of standard 0.5” EMT tubing (included). The remotely

mounted weather resistant power supply can withstand the wet

environment found inside of air handlers or the exposed conditions of

outdoor packaged air conditioning systems.

The number and placement of lamps is determined by several factors

including coil dimensions and condition or if airborne disinfection is

desired. BLUE-TUBE XL™ has everything needed for complete installation

in most AHU and RTU equipment.

*Installation of this product by anyone other than licensed HVAC or electrical contractors voids warranty.

COMMERCIAL SERIES GERMICIDAL UV LIGHT SYSTEM

INSTALLATION & MAINTENANCE

L M

Summary of content (8 pages)

PAGE 1
COMMERCIAL SERIES GERMICIDAL UV LIGHT SYSTEM INSTALLATION & MAINTENANCE BLUE-TUBE XL™ is designed for installation into commercial air handling units and rooftop package units for the purpose of surface or airborne disinfection using ultraviolet germicidal irradiation. For maximum installation flexibility and cost-effectiveness the UV lamps are mounted onto a framework of standard 0.5” EMT tubing (included).
PAGE 2
18” 32” Coil Sizing Reference SINGLE 32” LAMP Coil Mount Installation 1. Determine the dimensions of the coils or area to be irradiated. 32” 32” 2. Use the Coil Sizing Reference to determine the number of lamps needed for proper coverage. 3.
PAGE 3
Lamp Spacing 12” Max. space between lamps 6” Max.
PAGE 4
Duct Mount Installation System Configuration A: In-Line With Air Flow (pre-assembled parts are ready for this configuration) Configuration A Assembled 1. Cut an access panel into the duct. If necessary cover high exposure areas with UV-resistant reflective tape or similar material. 2. If needed, loosen or remove hardware then cut conduit to fit duct. 3. Mount the frame-work into the duct using the self-tapping screws or optional mounting magnets.
PAGE 5
1 Assemble Conduit Framework 1. Measure and cut tubing to length then slide on conduit/ lamp clamps (do not fully tighten bolts yet). 1. Slide On Hardware 2. Mount the L-bracket and tubing as shown. Mount L-bracket to air handler wall using screws or magnet (galvanized metal only). 2. Mount L-bracket and Tubing Conduit Mount UV Lamp on clips Use screws or magnet 2 Install UV Lamps Snap UV Lamps into the Lamp/conduit Clamps.
PAGE 6
Assemble Conduit Framework cont. 3. When needed, use the 12” Stand-off on the near side to create separation between lamps and coil or to suspend the lamps from the air handler ceiling, such as in a roof top unit. Mount the 12” Stand-off using self-tapping screws or by attaching a bracket magnet. Magnet Mount directly to air handler using using self-tapping screws or attach bracket magnet. 1/2” Pipe Strap EMT 12” separation is ideal for most coils.
PAGE 7
5 Sight Glass Installation 1. The sight glass allows safe viewing of the UV light system when in operation. Find a suitable location such as a door to the HVAC system for the sight glass. 2. Drill a 1” hole and press the base of the sight glass through it. 6 Power-up System Caution: UV-C light that can cause Serious Eye Burns and Temporary Blindness, Ensure all access panels have been replaced and doors closed before powering-up the system.
PAGE 8
Fresh-Aire UV® Commercial Series Accessories Customize your UVGI installation with genuine Fresh-Aire UV® Commercial Series Accessories. Available where you purchased your BLUE-TUBE XL™.