Operation Manual

D417E
Fig 6
1. Open the bell push
To open the front cover carefully
insert a flat bladed screw driver, into
the slot and twist gently (A). When
refitting the front cover to ensure
the weather proofing is maintained,
always mount the bell push in the
upright position and replace the
cover securely. Fig 1
2. To fit or replace the battery
Open the front cover and insert
the CR 2032 Lithium coin cell
battery into the base as shown
in Fig 2. Any debris created
during installation must be
removed from the base before
fitting battery, to ensure good contact.
3. Mount the bell push
Ensure the wall surface is clean
and dry. Mount using either the
double sided sticky pad on a
smooth surface, or the screws
and wall plugs provided, See Fig 3.
Do not mount the push on or near
(< 30cm) large metal objects, as it
will block signals from the push.
4. Test the bell push
When the bell push button is pressed,
the confidence light (B) in Fig 4, will
illuminate to reassure the caller that
the bell push is working.
The light will flash 5 times when
the battery needs replacing.
5. Use of the door chime
Plug the chime into any
220-240V BS 1363 socket,
installed in a clean dry
environment, situated
within transmission
range of the bell push,
as shown in Fig 5.
6. Automatic Programming of bell pushes
The first time a chime unit is powered up, the sounds available
are demonstrated. Press the door push until the chime
responds with a tune. You can leave this tune or change it to a
desired tune by using button A (see fig 6) (see Sound Selection).
To programme a second push, press the push button until the
chime sounds, then use button B to change the tune if
required. Programming is now completed.
If more than 5 minutes has elapsed, you will have to reset the
chime programing by pressing and holding buttons A and B
until the chime sounds, this takes approximately 5 seconds.
The chime can then be programmed to 1 or 2 door pushes.
All EVO and Décor Chimes and Bell Pushes use a self learning
feature to ensure no interaction from other neighbouring
systems.
7. Sound Selection
A = Main push sound selection
B = Second push sound selection
Chime tune options are as follows:
1. Tone Bar 2 Note (Default Tune for 1st Push)
2. Bass clarinet (Default Tune for 2nd Push)
A
B
A
Fig 1
Fig 2
Fig 4
Fig 5
B
Fig 3
Evo 50m* Wirefree
Plug-In Chime Kit
Declaration
Novar ED&S hereby declares that this
wirefree chime kit is in compliance with
the essential requirements and other
relevant provisions of the Radio and
Telecommunications Terminal Equipment
(R & TTE) directive, 1999/5/EC
Pack contents:
50m Plug-In Chime 230v
Bell push & CR2032 Lithium coin cell battery
Adhesive pad, 2 x screws (ø3x20mm) 2 x wall plugs (ø5x25mm)
for mounting the bell push
You will require:
A small crosshead and flathead screwdriver, a ø5 masonry drill
* The stated transmission range of this product is measured in
open field conditions. Walls ceilings, and metal structures will
reduce the maximum range.
Friedland guarantees this product for 3 years from date of purchase.
Proof of purchase is required, this does not affect your statutory rights.
If you require further information about our products, call the Friedland
helpline on 01268 563066.
Friedland a Novar business, Novar ED&S, The Arnold Centre,
Paycocke Road, Basildon, Essex, SS14 3EA, England
www.friedland.co.uk
+
Trouble Shooting
Chime not Sounding
Chime may be positioned out of range of the bell push
Move your chime closer to the bell push
A metallic object may be blocking the signal from bell push
position

Experiment with the location of the chime to see if you can
move it in a more suitable place
The battery in the bell push may need replacing
Press the bell push. If the confidence light (B) flashes 5 times
after being pushed, replace the battery.
Note: In cold conditions, poor location or environment,
operating at maximum range it is advisable to replace the
battery more frequently before the indicator light flashes
(i.e every 12 - 18 months) to maintain optimum performance
Your bell push and chime haven't been programmed
Reset the automatic programming of your chime and bell push
Instructions – Please retain these instructions for future reference