Friedrich Chill Air Conditioners Brochure

ManualsBrandsFriedrich ManualsDomestic AppliancesEP08G11B

Thru-the-wall Specifications



ENERGY STAR

models

WALLMASTER HEAT PUMP

HEATING PERFORMANCE: Change-over from heat pump operation to resistance

operation on models indicated is automatic at a preset outside ambient temperature

of approximately 35°F.

Calculate the heat loss of the space to be heated. As long as the heat loss does

not exceed the resistance heating capacity rating of the unit, the heating perfor-

mance will be satisfactory.

Note: all models will produce condensate. If condensate disposal is desired, an

optional drain kit is available.

DEFROST CONTROL: Initiated at 30°F (outdoor coil temperature) and terminated

at 43°F (outdoor coil temperature). During defrost, the compressor stops and the

electric heat starts, then operates with the fan to maintain indoor comfort. Below

43°F, the unit remains in electric heat mode.

DEFROST DRAIN: Drain automatically opens at approximately 50°F to prevent

condensate from freezing inside drain pan.

WallMaster Heat Pump heating information (shown in red) indicates heat pump heating performance. WallMaster Electric Heat heating information (shown in red)

indicates electric heat strip performance. For WallMaster Heat Pump electric heating performance refer to corresponding WallMaster Electric Heat model.

LISTED

ROOM AIR CONDITIONERS

183H

Thru-the-wall Optional Accessories

Model Height Width Depth

Depth

with

Front

Minimum

Extension

Into Room

Minimum

Ex tension

Outside

Thru-the-wall

Finished Hole

Height Width Max. Depth

WallMaster

WSE Sleeve 16 3/4" 27" 16 3/4" 23" 7 1/2" 9/16" 17 1/4" 27 1/4" 15 5/16"

Chassis 15 3/4" 26 1/2" 21" 22” – – – – –

Uni-Fit

USC Sleeve 15 1/2" 25 7/8" 16 3/4" 20 1/2" – 1/2" 15 3/4" 26 1/8" 16 1/4"

US Chassis 14 3/8" 24" 18 1/2” 20 1/8" 3 3/4" – – – –

UE Chassis 14 3/8" 24 5/8" 18” 19 5/8" 3 1/2" – – – –

Sleeve/Chassis Dimensions

IMPORTANT:

US chassis w/front fully installed into USC sleeve

extends into room 3

/8”. UE chassis w/front fully

installed into USC sleeve extends into room 2

/8”. 1” gap on sides and

/2” gap at top can be

covered by two-piece trim ring that ts over the

chassis front

STANDARD GRILLE – Ships with USC sleeve

Expanded aluminum grille designed for use with USC sleeve.

REPLACEMENT GRILLE – Ships with US/UE chassis

Black plastic for use on existing sleeves without any grille.

IMPORTANT:

When installing into an existing sleeve, consult Installation

Section of your Installation/Operation Manual to determine

whether or not the grille needs to be replaced and/or a bafe

adapter should be used.

Uni-Fit

26” Sleeve Exterior Grilles

USC Sleeve Standard Grille

Installation Accessories (27” sleeve models only)

IMPORTANT:

Operating the air conditioner

with incorrect rear grille or

without Bafe Adapter Kit

(on 19 3/4” deep sleeve) will

recirculate discharge air and

cause compressor overload

to trip.

This will cause the unit to shut

down temporarily and may

lead to premature compressor

failure.

CORRECT Vertical Louvers

INCORRECT Horizontal Louvers

WallMaster

27” Sleeve Exterior Grilles

WSE SLEEVE

Optional Architectural Grille- AG

Premium brushed aluminum

grille.

WSE SLEEVE

Standard Grille

Premium, stamped steel grille

with powder coat paint. Ships

with sleeve. Galvanized steel

inner and outer weather panels

also ship with sleeve.

DK / Drain Kit

Installed at the back of the unit and allows for

attachment to condensate disposal system, if

necessary or desired.

IDK / Internal Drain Kit

New construction applications

where a condensate drain system

has been built into the wall interior.

BAK / Bafe Adapter Kit

Necessary when installing in

a sleeve deeper than 16 3/4"

deep, such as Fedders B sleeve

(19 3/4" deep).

Trim ring

US= 3

/8”, UE= 2

/8”

Model

Carton Dimensions

INCHES

Height W i d t h Depth

WallMaster

WSE Sleeve 18" 27 1/4" 18"

Chassis 15 3/4" 26 1/2" 21"

Uni-Fit

USC Sleeve 17 7/8" 28" 19 1/4"

US Chassis 17 1/4" 27" 22 1/4”

UE Chassis 17" 27 1/4" 22”

Due to continuing research in new energy-saving technology, specications are subject to change without notice.

As an ENERGY STAR

partner, Friedrich Air Conditioning Co. has determined that the selected ENERGY STAR

models meet the ENERGY STAR

guidelines for energy efciency.

Your operating costs will depend on your utility rates and use. The estimated operating cost is based on a electricity

cost of $ .12 per kWh. For more information, visit www.ftc.gov/energy.

Power cords are located on front left of WallMaster models and on front right of Uni-Fit models.

Optional Architectural Grille UXAA

Estar

Model Cooling Btu Heating Btu

Volts

Rated

Cooling

Amps

Cooling

Watts

Heating

Amps

Heating

Watts

Energy

Efciency

Ratio

EER

Estimated

Yearly

Energy

Cost COP

Moisture

Removal

Pints/HR CFM Sleeve

Net

Weight

Lbs.

Ship

Weight

Lbs

WALLMASTER

Cool only



WS08C10D 8000 - 115 6.4 769 - - 10.4

$69

- 1.2 250 WSE 93 97



WS10C10D 9700 - 115 8.2 990 - - 9.8 $89 - 2.4 260 WSE 103 107



WS12C10D 11500 - 115 11.5 1174 - - 9.8 $106 - 3.1 295 WSE 112 116



WS10C30D 10000/9800 - 230/208 4.5/4.9 1020/1000 - - 9.8/9.8 $92 - 1.5 260 WSE 101 105



WS12C30D 11500/11200 - 230/208 5.5/6.0 1174/1143 - - 9.8/9.8 $106 - 3.0 290 WSE 109 113

WS16C30 15600/15000 - 230/208 8.3/8.9 1835/1765 - - 8.5/8.5 $165 - 4.2 290 WSE 119 123

Heat Pump



WY09C33D 9300/9000 7500/7500 230/208 4.3/4.6 949/918 3.9/4.1 833/833 9.8/9.8 $85 2.6/2.6 2.1 260 WSE 103 107

WY12C33 12000/11800 9350/9200 230/208 6.1/6.4 1395/1372 4.8/5.1 1062/1010 8.6/8.6 $126 2.5/2.6 2.6 275 WSE 111 115

Cool with Electric Heat

WE10C33D 10000/9800 11000/9100 230/208 4.5/4.9 1020/1000 16.0/14.7 3550/2950 9.8/9.8 $92 - 1.5 260 WSE 104 108

WE12C33D 11500/11200 11000/9100 230/208 5.5/6.0 1174/1143 16.0/14.7 3550/2950 9.8/9.8 $106 - 3.0 290 WSE 107 111

WE16C33 15600/15000 11000/9100 230/208 8.3/8.9 1835/1765 16.0/14.7 3550/2950 8.5/8.5 $165 - 4.2 290 WSE 119 123

UNI-FIT

Cool Only



US08D10B 8000 - 115 7.4 810 - - 9.8 $73 - 2.2 260 USC 73 79



US10D10B 9800 - 115 9.2 1000 - - 9.8 $90 - 3.2 260 USC 78 84



US12D10B 11500 - 115 10.7 1170 - - 9.8 $106 - 3.8 TBD USC 80 87



US10D30B 10000/9800 - 230/208 4.7/5.1 1020/1000 - - 9.8/9.8 $92 - 3.2 285 USC 78 86



US12D30B 11500/11200 - 230/208 5.4/5.8 1170/1140 - - 9.8/9.8 $106 - 3.8 260 USC 80 87

US14D30B 13000/12600 - 230/208 7.0/7.5 1530/1480 - - 8.5/8.5 $138 - 4.0 310 USC 87 94

Cool with Electric Heat

UE08D11B 8000 3850 115 7.5 830 10.7 1230 9.6 $77 - 2.2 260 USC 73 79

UE10D33B 10000/9800 11200/9200 230/208 4.7/5.2 1060/1040 15.3/14.0 3500/2900 9.4/9.4 $96 - 3.2 285 USC 78 84

UE12D33B 11500/11200 11200/9200 230/208 5.6/6.0 1220/1190 15.3/14.0 3500/2900 9.4/9.4 $110 - 3.8 290 USC 80 87

Plug Face/ Circuit Rating

WallMaster

Model Number

Uni-Fit

Model Number

Circuit

Rating

Breaker

or T-D Fuse

Plug

Face

(NEMA#)

Power

Cord

Length

(ft.)

Wall

Outlet

Appearance

WS08C10D, WS10C10D,

WS12C10D

US08D10B, UE08D11B

US10D10B, US12D10B

125V - 15A 5 - 15P 6

WS10C30D, WS12C30D,

WS16C30

US10D30B, US12D30B,

US14D30B

250V - 15A 6 - 15P 4

WE10C33D, WE12C33D,

WE16C33, WY09C33D, WY12C33

UE10D33B, UE12D33B 250V - 20A 6 - 20P 4