Service/ Parts Manual Floating Air Pro Multi-Zone Type Model Outdoor Condensor FPHMR18A3A Outdoor Condensor FPHMR24A3A Outdoor Condensor FPHMR36A3A Indoor Wall Mount FPMW07A3A Indoor Cassette FPHFC09A3A Indoor Cassette FPHFC12A3A Indoor Cassette FPHFC18A3A Indoor Cassette FPHFC24A3A Indoor Ducted FPHFD09A3A Indoor Ducted FPHFD12A3A Indoor Ducted FPHFD18A3A Indoor Ducted FPHFD24A3A Indoor Accessory FPCG0912 Indoor Accessory FPWC1 Indoor Accessory FPCG182436 1
TABLE OF CONTENTS Table of Contents INTRODUCTION‑ Important Safety Information‑ Personal Injury Or Death Hazards‑ MODEL IDENTIFICATION GUIDE‑ Product Appearance‑ SPECIFICATIONS‑ Product Specifications Multi-Zone Wall-Mounted‑ Product Specifications Multi-Zone-Cassette ‑ Product Specifications Multi-Zone Concealed Ducted ‑ Product Specifications 18K, 24k and 36k Outdoor Condensor‑ Product Dimensions: Wall Mounted Indoor Units‑ Product Dimensions: 9k, 12k, and 18k Ducted Indoor Units‑ Product Dime
TABLE OF CONTENTS Pumping Down‑ Gas Charging (After Repair)‑ Replace 24k Outdoor unit Compressor and Motor‑ Replace 36k Outdoor unit Compressor and Motor‑ Replace 9k and 12k Duct Type unit Compressor and Motor‑ Replace 18k Duct Type unit Compressor and Motor‑ COMPONENTS TESTING ‑ Resistance Table Of Indoor Coil And Indoor Room Sensor‑ Resistance Table Of Outdoor Compressor Temperature Sensor‑ Compressor‑ Fan Motor‑ 7k Indoor Wall Mount Printed Circuit Board ‑ Ducted units and Cassettes Printed C
INTRODUCTION Important Safety Information The information in this manual is intended for use by a qualified technician who is familiar with the safety procedures required for installation and repair, and who is equipped with the proper tools and test instruments required to service this product.
Important Safety Information INTRODUCTION CAUTION DO NOT OPERATE EQUIPMENT DURING ACTIVE STAGES OF CONSTRUCTION To ensure proper operation, Friedrich requires that all equipment is not operated during active construction phases. This includes active stages of completing framing, drywalling, spackling, sanding, painting, flooring, and moulding in the equipment’s designated conditioning space.
Personal Injury Or Death Hazards INTRODUCTION WARNING SAFETY FIRST Do not remove, disable or bypass this unit’s safety devices. Doing so may cause injuries, or death. AVERTISSEMENT Ne pas supprime, désactiver ou contourner cette l´unité des dispositifs de sécurité, faire vous risqueriez de provoquer le feu, les blessures ou la mort. ADVERTENCIA No eliminar, desactivar o pasar por alto los dispositivos de seguridad de la unidad. Si lo hace podría producirse fuego, lesiones o muerte.
MODEL IDENTIFICATION GUIDE INTRODUCTION MODEL IDENTIFICATION GUIDE Model Type: FR- Floating Air Premier FP - Floating Air Pro FS- F loating Air Sele ct Function : HS – H ea t Pump Single HM – Heat Pump Multi HF – H eat Pump F lex Single and Multizon e FP HS Voltag e 1- 115 Volts 3- 230 Volts W 09 A 1 A - A Application : W- Wallmounted D- Ducted (Insider ) C- Cassette R- Remo te Condense r 7 Approximate Coolin g BTU/HR Model Introductory Chara cter: A- 201 9 B- 202 0 C- 202 1 D- 202 2 Marketing Suf
INTRODUCTION Product Appearance Duct type Model (Btu/h) Indoor Unit 9K/12K 18 K Cassette type Model (Btu/h) 9K/12K 18K/ 24k/ 36k 8 Indoor Unit
Product Appearance INTRODUCTION Cassette type Model (Btu/h) 24 K 36 K 9 Indoor Unit Out door Unit
Product Appearance INTRODUCTION Outdoor Unit Type 3-Zone Tri 4-Zone Quad 10 Minimum and Maximum connectabel Capacity (Btu/h) 12,000-36,000 BTU 18,000-48,000 BTU View
SPECIFICATIONS Product Specifications Multi-Zone Wall-Mounted PERFORMANCE RATINGS INDOOR MODEL Multizone Wall-Mounted - Heat Pumps 7k 9k 12k 18k 24k FPHMW07A3A FPHFW09A3A FPHFW12A3A FPHFW18A3A FPHFW24A3A SPECIFICATIONS CAPACITY COOLING (RATED) BTU 7,000 9,000 12,000 18,000 24,000 CAPACITY HEATING (RATED) BTU 8,500 9,500 13,000 19,000 24,200 MOISTURE REMOVAL Pts/h 2.5 2.5 3.2 4.2 5.
SPECIFICATIONS Product Specifications Multi-Zone-Cassette PERFORMANCE RATINGS Multizone Cassette - Heat Pumps INDOOR MODEL 9k 12k 18k 24k FPHFC09A3A FPHFC12A3A FPHFC18A3A FPHFC24A3A SPECIFICATIONS CAPACITY COOLING (RATED) Btu 9,000 12,000 18,000 24,000 CAPACITY HEATING (RATED) Btu 10,200 13,500 20,400 27,000 MOISTURE REMOVAL Pts/h 1.9 2.5 3.2 5.0 AIRFLOW (HIGH) CFM 306 471 559 1100 SOUND RATING (MAX.-MIN.
SPECIFICATIONS Product Specifications Multi-Zone Concealed Ducted PERFORMANCE RATINGS Multizone - The Insider™ Concealed Ducted Heat Pumps INDOOR MODEL 9k 12k 18k FPHFD09A3A FPHFD12A3A FPHFD18A3A SPECIFICATIONS CAPACITY COOLING (RATED) Btu 9,000 12,000 18,000 CAPACITY HEATING (RATED) Btu 10,000 12,500 19,000 MOISTURE REMOVAL Pts/h 1.9 3.2 3.2 Max Airflow (@0.1 E.S.P.) CFM 294 353 529 SOUND RATING (MAX.-MIN.
SPECIFICATIONS Product Specifications 18K, 24k and 36k Outdoor Condensor Multi-Zone Flex 2 Indoor units 2 or 3 indoor units 2 to 4 indoor units Model Name FPHMR18A3A FPHMR24A3A FPHMR36A3A Gas R410A R410A R410A Capacity Cooling Capacity 95 ºF Btu/h 18000 24000 32000 Heating Rated Capacity 47 ºF Btu/h 18000 24000 36000 17 ºF Btu/h 12200 15400 22800 Heating Maximum Capacity 17 ºF Btu/h 20000 26000 40000 5 ºF Btu/h 18000 24000 36000 Cooling 95 ºF kW / / / Btu/h 1
SPECIFICATIONS Product Specifications 18K, 24k and 36k Outdoor Condensor Multi-Zone Flex 2 Indoor units 2 or 3 indoor units 2 to 4 indoor units Model Name FPHMR18A3A FPHMR24A3A FPHMR36A3A inch 860×670×310 37-3/8x33x13-3/8 37-3/8x41-3/8x13-3/8 mm 33 7/8x26 3/8x12 1/4 950×840×340 950×1050×340 lbs 49 158.73 188.5 kg 108.0 72 85.5 inch 990×450×730 43-3/8x18-1/8x36-1/4 43-3/8x18-1/8x47-1/4 mm 39x17 3/4x28 3/4 1110×460×920 1110×460×1200 Ibs 54 169.76 220.5 kg 119.
SPECIFICATIONS Product Dimensions: Wall Mounted Indoor Units 16 Model Width Height Depth FPHFW07A3A 33 7/8 “(Inches) 11 3/16 “(Inches) 8 1/2 “(Inches) FPHFW09A3A 33 7/8 “(Inches) 11 3/16 “(Inches) 8 1/2 “(Inches) FPHFW12A3A 33 7/8 “(Inches) 11 3/16 “(Inches) 8 1/2 “(Inches) FPHFW18A3A 45 3/16 “(Inches) 13 1/8 “(Inches) 9 15/16 “(Inches) FPHFW24A3A 45 3/16 “(Inches) 13 1/8 “(Inches) 9 15/16 “(Inches)
SPECIFICATIONS Drain pipe 5-1/4(134) 5(127) 3-3/8 (85) 1-3/8(35) 3-7/8(98) 7-1/12(190) 6-11/16(170) Gas pipe Liquid pipe Product Dimensions: 9k, 12k, and 18k Ducted Indoor Units 6-11/16(170) 5-3/16(131) 8-3/4(222) Air outlet 14-3/4(375) 17-5/8(447) Air inlet Unit: Inches “ (mm) 6-1/2(165) Air outlet Electric box Air inlet Model a b c d 37- 13/16 (961) 35- 13/16 (910) 29-1/2 (749) 30 (786) 48-7/16 (1231) 46-7/16 (1180) 40-1/8 (1019) 41- 5/8 (1056) ( Btu/h) 9K/12K 18K 17
SPECIFICATIONS Product Dimensions: 9k and 12k Cassette 24-7/16(620) 12(305) 10-13/16(275) 24-7/16(620) 22-7/16(570) 12-11/16(323) 2-7/16 (62) 1-7/8(48) Unit: Inches “ (mm) 20-1/4(515) 2-1/16(52) 1-5/8 (41) 5-3/16 (131) 8-7/16 (215) 2(51) 3-1/8 (79) 5-1/16 (128) 5-7/16 (138) 24-7/16(620) 22-5/8~23-1/4(575~590) 20-7/8(530) 3-11/16 (93) 22-5 /8~23-1/4(575~590) 24-7/16(620) 18
SPECIFICATIONS Product Dimensions: 18k and 24k Cassette Unit: Inches “ (mm) 37- 3/8(95 0) (490 ) (478 ) (520 ) 37-3/8(950) 33-1/16(840) 29-7/8(760) 33-7/8~35-13/16(860~910) 19 4-5/8 (118) 4-1/32(102) 9-3/4(248) 5-1/8 (130) 4-1/32 (102) 4-5/16 (110) (45 ) 7-1/8 (180) 5 (127) 33-7/8~35-13/16(860~910) 29-7/8(7 60 ) 33-1/8(841)
SPECIFICATIONS Product Dimensions: 24k Outdoor Units 33-1/16(840) 4-5/16(110) 10-1/4(260)=5X2-1 /16(52) Unit: Inches “ (mm) 7-1/4(185) 7(180) 22- 7/8(580) 37- 3/8(950) 40- 7/8(1032) 3-1/4(82) 1-5/8(41) 13-3/8(340) 14-15/16(380) 16-1/4(414) 13- 9/16(344) 5/8(15) 20 2-3/4(70)
SPECIFICATIONS Product Dimensions: 36k Outdoor Units 14- 1/2(368) 3-1/4(83) 3-7/8(100) 3-7/8(100) 5-1/4(133) 3-7/8(100) 3-7/8(100) 3-7/8(100) 3-7/8(100) 41-5/16(1050) Unit: Inches” (mm) 21-1/2(546) 13- 1/2(349) 37- 3/8(950) 22-7/8(580) 13- 9/16(344) 13-3/8(340) 14-15/16(380) 1-5/8(41) 7-1/4(18 5) 2-3/4(70 ) 5/8(15) 21
Capacity Characteristics Chart SPECIFICATIONS Non-Ducted Fphmr18a3a Cooling NON-DUCTED FPHMR18A3A Indoor units(Btu) 07+07 07+09 07+12 09+09 09+12 12+12 22 Outdoor Air Temp. (°F DB) 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 64 / 54 TC SHC kBtu/h 9.17 7.65 9.00 7.46 8.93 7.39 8.82 7.34 8.89 7.38 9.40 7.62 11.38 8.
SPECIFICATIONS Capacity Characteristics Chart Ducted Fphmr18a3a Cooling DUCTED FPHMR18A3A Indoor units(Btu) 07+07 07+09 07+12 09+09 09+12 12+12 23 Outdoor Air Temp. (°F DB) 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 64 / 54 TC SHC kBtu/h 7.91 6.59 7.76 6.43 7.70 6.37 7.60 6.33 7.67 6.36 8.10 6.57 9.81 7.48 9.51 7.
Capacity Characteristics Chart Mixed Fphmr18a3a Cooling MIXED FPHMR18A3A Indoor units(Btu) 07+07 07+09 07+12 09+09 09+12 12+12 24 Outdoor Air Temp. (°F DB) 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 64 / 54 TC SHC kBtu/h 8.53 7.11 8.37 6.93 8.30 6.87 8.20 6.83 8.27 6.86 8.74 7.09 10.58 8.06 10.26 7.93 9.99 7.80 9.
SPECIFICATIONS Capacity Characteristics Chart Mixed Fphmr18a3a Cooling Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart DUCTED Ducted Fphmr18a3a HeatingFPHMR18A3A HEATING Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR18A3A HEATING Mixed Fphmr18a3a Heating Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED Non-Ducted Fphmr24a3a Heating Indoor units(Btu) 07+09 07+12 07+18 09+09 09+12 09+18 12+12 12+18 18+18 28 Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart Non-Ducted Fphmr24a3a Cooling NON-DUCTED 07+07+07 07+07+09 07+07+12 07+07+18 07+09+09 07+09+12 07+09+18 07+12+12 07+12+18 09+09+09 29 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50
SPECIFICATIONS Capacity Characteristics Chart Non-Ducted Fphmr24a3a Cooling NON-DUCTED FPHMR24A3A COOLING 09+09+12 09+09+18 09+12+12 12+12+12 30 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 20.89 20.44 20.16 19.90 20.08 21.21 25.18 24.82 24.22 23.46 19.98 14.71 21.15 20.70 20.40 20.15 20.32 21.47 25.49 25.13 24.52 23.75 20.23 14.89 20.98 20.53 20.24 19.98 20.16 21.30 25.28 24.92 24.32 23.
SPECIFICATIONS Capacity Characteristics Chart FPHMR24A3A Ducted DUCTED Fphmr24a3a Cooling Outdoor Indoor units(Btu) Air Temp.
SPECIFICATIONS Capacity Characteristics Chart DUCTED FPHMR24A3A Ducted Fphmr24a3a Cooling 18+18 07+07+07 07+07+09 07+07+12 07+07+18 07+09+09 07+09+12 07+09+18 07+12+12 32 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77
SPECIFICATIONS Capacity Characteristics Chart Ducted Fphmr24a3a Cooling DUCTED FPHMR24A3A COOLING 07+12+18 09+09+09 09+09+12 09+09+18 09+12+12 12+12+12 33 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 21.15 20.70 20.40 20.15 20.32 21.47 25.49 25.13 24.52 23.75 20.23 14.89 19.90 19.48 19.20 18.96 19.13 20.21 23.99 23.
SPECIFICATIONS Capacity Characteristics Chart FPHMR24A3A Mixed MIXED Fphmr24a3a Cooling Indoor units(Btu) 07+09 07+12 07+18 09+09 09+12 09+18 12+12 12+18 34 Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart Mixed Fphmr24a3a Cooling MIXED FPHMR24A3A 18+18 07+07+07 07+07+09 07+07+12 07+07+18 07+09+09 07+09+12 07+09+18 07+12+12 35 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR24A3A Mixed Fphmr24a3a Cooling 07+12+18 09+09+09 09+09+12 09+09+18 09+12+12 12+12+12 36 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 21.15 20.70 20.40 20.15 20.32 21.47 25.49 25.13 24.52 23.75 20.23 14.89 20.33 19.90 19.62 19.37 19.54 20.65 24.51 24.16 23.
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR24A3A Non-Ducted Fphmr24a3a Heating HEATING Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED Non-Ducted Fphmr24a3a HeatingFPHMR24A3A 09+18 12+12 12+18 18+18 07+07+07 07+07+09 38 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65
Capacity Characteristics Chart SPECIFICATIONS Non-Ducted Fphmr24a3a HeatingFPHMR24A3A NON-DUCTED 07+07+12 07+07+18 07+09+09 07+09+12 07+09+18 07+12+12 39 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED Non-Ducted Fphmr24a3a Heating FPHMR24A3A 07+12+18 09+09+09 09+09+12 09+09+18 09+12+12 12+12+12 40 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 4
Capacity Characteristics Chart SPECIFICATIONS DUCTEDHeating FPHMR24A3A Ducted Fphmr24a3a HEATING Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart DUCTED FPHMR24A3A Ducted Fphmr24a3a Heating 09+18 12+12 12+18 18+18 07+07+07 07+07+09 42 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7
Capacity Characteristics Chart SPECIFICATIONS Ducted Fphmr24a3a Heating DUCTED FPHMR24A3A 07+07+12 07+07+18 07+09+09 07+09+12 07+09+18 07+12+12 43 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50
Capacity Characteristics Chart SPECIFICATIONS DUCTED FPHMR24A3A Ducted Fphmr24a3a Heating 07+12+18 09+09+09 09+09+12 09+09+18 09+12+12 12+12+12 44 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50
Capacity Characteristics Chart SPECIFICATIONS MIXED FPHMR24A3A Mixed Fphmr24a3a Heating HEATING Outdoor Air Temp.
Capacity Characteristics Chart SPECIFICATIONS MIXEDHeating FPHMR24A3A Mixed Fphmr24a3a 09+18 12+12 12+18 18+18 07+07+07 07+07+09 46 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3
Capacity Characteristics Chart SPECIFICATIONS MIXED FPHMR24A3A Mixed Fphmr24a3a Heating 07+07+12 07+07+18 07+09+09 07+09+12 07+09+18 07+12+12 47 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59
Capacity Characteristics Chart SPECIFICATIONS MIXEDHeating FPHMR24A3A Mixed Fphmr24a3a 07+12+18 09+09+09 09+09+12 09+09+18 09+12+12 12+12+12 48 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59
SPECIFICATIONS Capacity Characteristics Chart Non-Ducted Fphmr36a3a Cooling NON-DUCTED FPHMR36A3A COOLING Indoor units(Btu) 07+09+18 07+09+24 07+12+12 07+12+18 07+12+24 07+18+24 09+09+12 09+09+18 09+09+24 49 Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED Non-Ducted Fphmr36a3a Cooling 09+12+12 09+12+18 09+12+24 09+18+24 12+12+12 12+12+18 12+12+24 12+18+24 07+07+07+07 07+07+07+09 50 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32
Capacity Characteristics Chart SPECIFICATIONS NON-DUCTED Non-Ducted Fphmr36a3a Cooling 07+07+07+12 07+07+07+18 07+07+07+24 07+07+09+09 07+07+09+12 07+07+09+18 07+07+09+24 07+07+12+12 07+07+12+18 07+07+12+24 51 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 7
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED Non-Ducted Fphmr36a3a Cooling 07+09+09+09 07+09+09+12 07+09+09+18 07+09+09+24 07+09+09+24 07+09+09+24 07+09+09+24 07+09+12+12 07+09+12+18 07+09+12+24 52 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 7
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED Non-Ducted Fphmr36a3a Cooling 07+12+12+12 07+12+12+18 09+09+09+09 09+09+09+12 09+09+09+18 09+09+09+24 09+09+12+12 09+09+12+18 09+09+12+24 09+12+12+12 53 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 7
SPECIFICATIONS Capacity Characteristics Chart Non-Ducted Fphmr36a3a Cooling NON-DUCTED 09+12+12+18 12+12+12+12 12+12+12+18 54 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 30.50 29.94 29.69 29.32 29.58 31.25 37.84 36.68 35.71 34.71 29.44 21.67 29.99 29.44 29.20 28.83 29.08 30.73 37.20 36.07 35.11 34.13 28.95 21.31 31.01 30.44 30.19 29.81 30.07 31.78 38.47 37.30 36.31 35.29 29.93 22.04 24.48 23.88 23.67 23.51 23.62 24.40 27.77 27.
Capacity Characteristics Chart SPECIFICATIONS NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Heating 09+09+12+24 09+12+12+12 09+12+12+18 12+12+12+12 12+12+12+18 55 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28
SPECIFICATIONS Capacity Characteristics Chart FPHMR36A3A Mixed MIXED Fphmr36a3a Cooling Indoor units(Btu) 07+09+18 07+09+24 07+12+12 07+12+18 07+12+24 07+18+24 09+09+12 09+09+18 56 Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A Mixed Fphmr36a3a Cooling 09+09+24 09+12+12 09+12+18 09+12+24 09+18+24 12+12+12 12+12+18 12+12+24 12+18+24 57 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A Mixed Fphmr36a3a Cooling 07+07+07+07 07+07+07+09 07+07+07+12 07+07+07+18 07+07+07+24 07+07+09+09 07+07+09+12 07+07+09+18 07+07+09+24 58 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104
SPECIFICATIONS Capacity Characteristics Chart Mixed Fphmr36a3a MIXED Cooling FPHMR36A3A 07+07+12+12 07+07+12+18 07+07+12+24 07+09+09+09 07+09+09+12 07+09+09+18 07+09+09+24 07+09+09+24 07+09+09+24 59 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104
SPECIFICATIONS Capacity Characteristics Chart Mixed Fphmr36a3a Cooling MIXED FPHMR36A3A 07+09+09+24 07+09+12+12 07+09+12+18 07+09+12+24 07+12+12+12 07+12+12+18 09+09+09+09 09+09+09+12 09+09+09+18 60 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A Mixed Fphmr36a3a Cooling 09+09+09+24 09+09+12+12 09+09+12+18 09+09+12+24 09+12+12+12 09+12+12+18 12+12+12+12 12+12+12+18 61 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 30.
SPECIFICATIONS Capacity Characteristics Chart FPHMR36A3A Ducted DUCTED Fphmr36a3a Cooling Indoor units(Btu) 07+09+18 07+09+24 07+12+12 07+12+18 07+12+24 07+18+24 09+09+12 09+09+18 62 Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart DUCTEDCooling FPHMR36A3A Ducted Fphmr36a3a 09+09+24 09+12+12 09+12+18 09+12+24 09+18+24 12+12+12 12+12+18 12+12+24 12+18+24 63 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 7
SPECIFICATIONS Capacity Characteristics Chart Ducted DUCTED Fphmr36a3aFPHMR36A3A Cooling 07+07+07+07 07+07+07+09 07+07+07+12 07+07+07+18 07+07+07+24 07+07+09+09 07+07+09+12 07+07+09+18 07+07+09+24 64 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104
SPECIFICATIONS Capacity Characteristics Chart DUCTEDCooling FPHMR36A3A Ducted Fphmr36a3a 07+07+12+12 07+07+12+18 07+07+12+24 07+09+09+09 07+09+09+12 07+09+09+18 07+09+09+24 07+09+09+24 07+09+09+24 65 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104
SPECIFICATIONS Capacity Characteristics Chart DUCTED FPHMR36A3A Ducted Fphmr36a3a Cooling 07+09+09+24 07+09+12+12 07+09+12+18 07+09+12+24 07+12+12+12 07+12+12+18 09+09+09+09 09+09+09+12 09+09+09+18 66 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 10
SPECIFICATIONS Capacity Characteristics Chart DUCTEDCooling FPHMR36A3A Ducted Fphmr36a3a 09+09+09+24 09+09+12+12 09+09+12+18 09+09+12+24 09+12+12+12 09+12+12+18 12+12+12+12 12+12+12+18 67 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 14 23 32 41 50 59 67 77 87 95 104 115 29.
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Cooling HEATING Outdoor Air Temp.
SPECIFICATIONS Capacity Characteristics Chart FPHMR36A3A Non-DuctedNON-DUCTED Fphmr36a3a Cooling 07+18+24 09+09+12 09+09+18 09+09+24 09+12+12 09+12+18 69 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43
SPECIFICATIONS Capacity Characteristics Chart FPHMR36A3A Non-DuctedNON-DUCTED Fphmr36a3a Cooling 09+12+24 09+18+24 12+12+12 12+12+18 12+12+24 12+18+24 70 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Heating 07+07+07+07 07+07+07+09 07+07+07+12 07+07+07+18 07+07+07+24 07+07+09+09 71 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Heating 07+07+09+12 07+07+09+18 07+07+09+24 07+07+12+12 07+07+12+18 07+07+12+24 72 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Heating 07+09+09+09 07+09+09+12 07+09+09+18 07+09+09+24 07+09+09+24 07+09+09+24 73 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Heating 07+09+09+24 07+09+12+12 07+09+12+18 07+09+12+24 07+12+12+12 07+12+12+18 74 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17
SPECIFICATIONS Capacity Characteristics Chart NON-DUCTED FPHMR36A3A Non-Ducted Fphmr36a3a Heating 09+09+09+09 09+09+09+12 09+09+09+18 09+09+09+24 09+09+12+12 09+09+12+18 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17
Capacity Characteristics Chart SPECIFICATIONS DUCTED FPHMR36A3A Ducted Fphmr36a3a Heating HEATING Outdoor Air Temp.
Capacity Characteristics Chart SPECIFICATIONS DUCTED Heating FPHMR36A3A Ducted Fphmr36a3a 07+18+24 09+09+12 09+09+18 09+09+24 09+12+12 09+12+18 77 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50
SPECIFICATIONS Capacity Characteristics Chart DUCTED FPHMR36A3A Ducted Fphmr36a3a Heating 09+12+24 09+18+24 12+12+12 12+12+18 12+12+24 12+18+24 78 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50
SPECIFICATIONS Capacity Characteristics Chart Ducted Fphmr36a3a DUCTEDHeating FPHMR36A3A 07+07+07+07 07+07+07+09 07+07+07+12 07+07+07+18 07+07+07+24 07+07+09+09 79 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 1
SPECIFICATIONS Capacity Characteristics Chart DUCTED FPHMR36A3A HEATING Ducted Fphmr36a3a Heating 07+07+09+12 07+07+09+18 07+07+09+24 07+07+12+12 07+07+12+18 07+07+12+24 80 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17
SPECIFICATIONS Capacity Characteristics Chart DUCTEDHeating FPHMR36A3A Ducted Fphmr36a3a 07+09+09+09 07+09+09+12 07+09+09+18 07+09+09+24 07+09+09+24 07+09+09+24 81 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 1
SPECIFICATIONS Capacity Characteristics Chart DUCTEDHeating FPHMR36A3A Ducted Fphmr36a3a 07+09+09+24 07+09+12+12 07+09+12+18 07+09+12+24 07+12+12+12 07+12+12+18 82 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 1
SPECIFICATIONS Capacity Characteristics Chart DUCTED FPHMR36A3A Ducted Fphmr36a3a Heating 09+09+09+09 09+09+09+12 09+09+09+18 09+09+09+24 09+09+12+12 09+09+12+18 83 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12
SPECIFICATIONS Capacity Characteristics Chart DUCTEDHeating FPHMR36A3A Ducted Fphmr36a3a 09+09+12+24 09+12+12+12 09+12+12+18 12+12+12+12 12+12+12+18 84 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47
Capacity Characteristics Chart SPECIFICATIONS MIXED FPHMR36A3A Mixed Fphmr36a3a Heating HEATING Outdoor Air Temp.
Capacity Characteristics Chart SPECIFICATIONS MIXED Heating FPHMR36A3A Mixed Fphmr36a3a 07+18+24 09+09+12 09+09+18 09+09+24 09+12+12 09+12+18 86 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A Mixed Fphmr36a3a Heating 09+12+24 09+18+24 12+12+12 12+12+18 12+12+24 12+18+24 87 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A Mixed Fphmr36a3a Heating 07+07+07+07 07+07+07+09 07+07+07+12 07+07+07+18 07+07+07+24 07+07+09+09 88 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A HEATING Mixed Fphmr36a3a Heating 07+07+09+12 07+07+09+18 07+07+09+24 07+07+12+12 07+07+12+18 07+07+12+24 89 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -
Capacity Characteristics Chart SPECIFICATIONS MIXEDHeating FPHMR36A3A Mixed Fphmr36a3a 07+09+09+09 07+09+09+12 07+09+09+18 07+09+09+24 07+09+09+24 07+09+09+24 90 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19
SPECIFICATIONS Capacity Characteristics Chart Mixed Fphmr36a3a Heating MIXED FPHMR36A3A 07+09+09+24 07+09+12+12 07+09+12+18 07+09+12+24 07+12+12+12 07+12+12+18 91 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19
Capacity Characteristics Chart SPECIFICATIONS MIXEDHeating FPHMR36A3A Mixed Fphmr36a3a 09+09+09+09 09+09+09+12 09+09+09+18 09+09+09+24 09+09+12+12 09+09+12+18 92 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19
SPECIFICATIONS Capacity Characteristics Chart MIXED FPHMR36A3A Mixed Fphmr36a3a Heating 09+09+12+24 09+12+12+12 09+12+12+18 12+12+12+12 12+12+12+18 93 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -15 -5 5 14 23 32 41 47 50 59 68 75 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47 50 59 65 -17 -7 3 12 19 28 37 43 47
SPECIFICATIONS Capacities andChart selection data Capacity Characteristics Single Zone Cassette "The Insider" - Concealed Ducted Cooling Capacity Table Outdoor Model Air Temp. (Btu/h) (°F DB) 9K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 Indoor Air Temp. °F DB / °F WB 68 / 57 TC SHC 8.91 8.90 8.89 8.88 8.87 8.85 8.84 8.82 8.81 8.80 8.79 8.78 8.76 8.75 8.54 8.33 8.12 7.91 7.68 7.50 7.31 7.12 6.93 6.55 6.42 7.14 7.19 7.25 7.29 7.35 7.40 7.45 7.50 7.55 7.60 7.65 7.
SPECIFICATIONS Capacity Characteristics Chart data Capacities and selection Single Zone Cassette Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 12K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 73 / 61 77 / 64 80 / 67 86 / 72 90 / 75 TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 11.89 9.52 11.87 9.59 11.85 9.66 11.84 9.73 11.82 9.80 11.80 9.87 11.79 9.94 11.77 10.00 11.75 10.07 11.
SPECIFICATIONS Capacity Characteristics Chart Capacities Single Zone Cassette and selection data Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 18K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 73 / 61 77 / 64 80 / 67 86 / 72 90 / 75 TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 17.83 14.28 17.81 14.39 17.78 14.49 17.75 14.59 17.73 14.69 17.70 14.80 17.68 14.90 17.65 15.00 17.63 15.
SPECIFICATIONS Capacity Characteristics Chart Capacities and selection data Single Zone Cassette Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 24K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 73 / 61 77 / 64 80 / 67 86 / 72 90 / 75 TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 23.77 19.04 23.74 19.18 23.70 19.32 23.67 19.45 23.64 19.59 23.60 19.73 23.57 19.87 23.53 20.00 23.50 20.
SPECIFICATIONS Capacity Characteristics Chart Single ZoneCapacities Cassette and selection data Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 36K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 TC SHC 10.41 10.39 10.37 10.36 10.35 10.33 10.32 10.30 10.29 10.27 10.26 10.24 10.23 10.21 9.97 9.72 9.48 9.23 8.97 8.75 8.53 8.31 8.09 7.65 7.49 8.33 8.40 8.46 8.51 8.58 8.64 8.70 8.76 8.82 8.87 8.93 8.99 9.05 9.11 8.96 8.
SPECIFICATIONS Capacities and selection data Capacity Characteristics Chart Single ZoneCassette Cassette Cooling Capacity Table Outdoor Model Air Temp. (Btu/h) (°F DB) 9K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 Indoor Air Temp. °F DB / °F WB 68 / 57 TC SHC 8.91 8.90 8.89 8.88 8.87 8.85 8.84 8.82 8.81 8.80 8.79 8.78 8.76 8.75 8.54 8.33 8.12 7.91 7.68 7.50 7.31 7.12 6.93 6.55 6.42 7.14 7.19 7.25 7.29 7.35 7.40 7.45 7.50 7.55 7.60 7.65 7.70 7.75 7.80 7.67 7.54 7.
SPECIFICATIONS Capacity Characteristics Chart Capacities and selection data Single Zone Cassette Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 12K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 73 / 61 77 / 64 80 / 67 86 / 72 90 / 75 TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 11.89 9.52 11.87 9.59 11.85 9.66 11.84 9.73 11.82 9.80 11.80 9.87 11.79 9.94 11.77 10.00 11.75 10.
SPECIFICATIONS Capacity Characteristics Chart Capacities Single Zone Cassetteand selection data Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 18K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 73 / 61 77 / 64 80 / 67 86 / 72 90 / 75 TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 17.83 14.28 17.81 14.39 17.78 14.49 17.75 14.59 17.73 14.69 17.70 14.80 17.68 14.90 17.65 15.00 17.63 15.
SPECIFICATIONS Capacity Characteristics Chart Capacities Single Zone Cassette and selection data Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 24K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 73 / 61 77 / 64 80 / 67 86 / 72 90 / 75 TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI TC SHC PI 23.77 19.04 23.74 19.18 23.70 19.32 23.67 19.45 23.64 19.59 23.60 19.73 23.57 19.87 23.53 20.00 23.50 20.
SPECIFICATIONS Capacity Characteristics Chart Capacities Single Zone Cassetteand selection data Cooling Capacity Table Indoor Air Temp. °F DB / °F WB Outdoor Model Air Temp. (Btu/h) (°F DB) 36K 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 118 122 68 / 57 TC SHC 10.58 10.56 10.55 10.53 10.52 10.50 10.49 10.47 10.46 10.44 10.43 10.41 10.39 10.38 10.13 9.88 9.63 9.38 9.12 8.89 8.67 8.45 8.23 7.77 7.62 8.47 8.53 8.60 8.65 8.72 8.78 8.84 8.90 8.96 9.02 9.08 9.14 9.20 9.26 9.
SPECIFICATIONS Sound Pressure Data 24k and 36k Outdoor Units Model 24K 3.28ft( 1.0m ) ahead of the unit; Test condition 3ft(0.92m ) high from the bottom of the unit; 3.28ft( 1.0m ) high from the ground Model 36K Test condition 3.28ft (1.0m) ahead of the unit; 1.79ft (0.546m) high from the bottom of the unit;3.28ft (1.
SPECIFICATIONS Sound Pressure Data Indoor Ducted Units Units 9K Model 12K Test condition 4.6ft(1. 4m) under the unit; 3.3ft(1 .0m) high from the ground Test condition 4.6ft(1.4m) under the unit; 3.3ft(1.0m) high from the ground 90 90 80 80 70 NC-70 NC-65 60 NC-60 NC-55 50 NC-50 NC-45 Hi 40 Lo Med 30 NC-40 NC-35 NC-30 NC-25 20 NC-20 10 NC-15 125 63 250 1k 500 2k 4k 8k 18K Test condition 4.6ft(1.4m) under the unit; 3.3ft(1.
SPECIFICATIONS Sound Pressure Data Cassettes Model 9K Model Test condition 4.6ft(1.4m) from the unit; 3.3ft(1.0m) high from the ground 90 90 80 80 70 70 NC-70 NC-70 NC-65 60 NC-60 NC-55 50 NC-50 NC-45 40 NC-40 Hi NC-35 30 Med NC-30 Lo NC-25 20 Total octave band sound level(dB:total sound level C) Total octave band sound level(dB:total sound level C) 12K Test condition 4.6ft(1.4m) from the unit; 3.3ft(1.
Sound Pressure Data Cassettes SPECIFICATIONS Model 36K Test condition 4.6ft(1.4m) from the unit; 3.3ft(1.
Air Flow Distribution 24k Cassette SPECIFICATIONS 1) Coo ling/ Air Velocity Distribution 2) Cooling/ Air Temperature Distribution 3) Heating/ Air Velocity Distribution 4) He ating/ Air Temperature Distribution 108
SPECIFICATIONS ESP (External Static Pressure) chart (Duct Type) 9k Standard E SP Chart ( 0 Pa) 0.2 (50) Limit High 0.16(40) Middle 0.12(30) Low Rated 0.08(20) (Pa) External static pressure inH2O (Pa) 0.24 (60) Middle High 0.04(10) Low 0 70 14 0 21 0 350 28 0 42 0 (CFM) High E SP Chart (5 0 Pa) External static pressure inH2O (Pa) 0.4 (100) 0.36 (90) 0.32 (80) 0.28 (70) 0.24 (60) limit Rated 0.2 (50) Middle 0.16 (40) 0.12 (30) High 0.08 (20) Low 0.
SPECIFICATIONS ESP (External Static Pressure) chart (Duct Type) 12k Standard E SP Chart ( 0 Pa) 0.28 (70) limit Limit 0.24 (60) High 0.2 (50) Middle High 0.16 (40) Middle Low Low 0.12 (30) Rated (Pa) External static pressure inH20 (pa) 0.32(80) 0.08 (20) 0.04 (10) Rated 0 70 14 0 210 350 280 420 (CFM) High E SP Chart (5 0 Pa) 0.4 (100) External static pressure inH20 (pa) 0.36 (90) 0.32 (80) limit 0.28 (70) 0.24 (60) High 0.20 (50) Rated Middle 0.16 (40) Low 0.
SPECIFICATIONS ESP (External Static Pressure) chart (Duct Type) 18k Standard E SP Chart ( 0 Pa) E xternal static pressure InH20 (Pa) 0.20 (50) 0.18 (45) 0.16 (40) Limit High 0.14 (35) Middle 0.12 (30) 0.10 (25) Low 0.08 (20) Middle Rated (Pa) High 0.06 (15) 0.04 (10) Low 0.02 (5) 0 70 140 210 280 420 350 490 630 560 Airflow rate (CFM) High E SP Chart (5 0 Pa) 0.24 (60) External static pressure InH20 (Pa) limit R ated 0.20 (50) 0.16 (40) Middle 0.12 (30) Low High 0.
SPECIFICATIONS Refrigerant Cycle 24k and 36k Outdoor Units 24k 36 K Fan Coil Temperature Coil Temperature Sensor Ambient Temperature Sensor Ambient Temperature Muffler Coil Temperature Frost Temperature Sensor Water Level Switch Ambient Temperature Water Level Switch S Liquid Stop Volve High Pressure Switch EEV X 4 4-Way Valve Coil Temperature HP Liquid Temperature Sencor X 4 Ambient Temperature Water Level Switch Muffler X 4 S Discharge Temperature Sensor LP S Suction Temperature S
SPECIFICATIONS Electrical Requirements 24k and 36k Outdoor Units Common wiring Electrical wiring diagram Outdoor unit Terminal Important: Wiring for wall mounted units Terminal A 1(L) L1 L2 1(L) Indoor unit A 2(N) 2(N) 4(SI) 4(SI) Terminal Indoor unit Outdoor unit Power connecting cord 1(L) Terminal B 1(L) Power supply Power connecting cord Power connecting cord 1(L) Indoor unit B 2(N) 2(N) 4(SI) 4(SI) Terminal 3(SI) 2(N) 2(L) 4(SI) 1(N) Terminal C 1(L) Power connecting c
SPECIFICATIONS Electrical Requirements 24k and 36k Outdoor Units (1) Follow local codes and regulations when selecting wire size and breakers IMPORTANT 1. When connecting the terminal block using stranded wire, make sure to use a round crimp-style terminal for connection to the power supply terminal block. Place the round crimp-style terminals on the wires up to the covered part and secure in place. covered part Round crimp- style terminal Stranded wire Terminal 2.
CORRECTION FACTORS Piping Length Correctiion Factor Piping length correction factor Pipe length L Indoor unit Height difference H Outdoor unit Th e correction facto r is base d on the equi valent piping length in feet (EL ) and the height between outdoor and indoor units in feet (H). IMPORTANT: Height correction factor is used BEFORE length correction factor. Height between indoor unit and outdoor unit (ft). P osition of outdoor unit is higher than position of indoor unit (ft).
Piping Length Factor Chart CORRECTION FACTORS The correction factor of height between each indoor unit and outdoor unit 16ft(5m) 32.8ft( 10m) 49ft(15m) 66ft(20m ) 82ft(25m ) 98ft(30m ) 1.0 0.95 0.88 0.8 0.75 0.7 To ensure correc t unit selec tion, co nsider the farthest indoo r unit. NOT E : 1. The above data reflects that the minimum height requirements have been meet or exceeded during the installation. The height difference between the indoor and outdoor unit is based at 0ft/0m.
CORRECTION FACTORS Piping Length Correctiion Factor Correction factors according to defrosting operation The heating capacity in the preceding paragraph excludes the condition of the frost or the or the defrosting operation period. In consideration of the frost or the defrosting operation, the heating capacity is corrected by the equation below.
OPERATION Display Panel D isplay panel C assette Type 5 4 6 7 1 6 3 2 2 1 6 7 2 7 1 5 4 3 5 4 D escription 1 Run indicator (Red) It lights on during operation. It lights off during SLEEP mode. 2 Emergency switch The filter clean indicator is reset when the switch is pressed. The unit will be started or stopped when the switch is pressed. The unit will be operated in forced cooling mode if press the switch continuously for more than 5s, the unit will operate in cooling mode.
OPERATION Figure 301 Remote Control Operation and Function 119
Remote Technical Parameters OPERATION Remote receiver distance (front of the air conditioner): 26ft. Remote receiver angle: Less than 60 degrees. Temperature control accuracy: ±2.4°F. Time Response: Less than 1 second. Display Functions Remote Current control functions on the remote controller (See unit’s “Installation and Operating Manual”) Display of the indoor unit displays set temperature or indoor temperature. Indoor unit Running LED lit during operation, flashing when in defrost.
Using Sleep during Off-Timer Function OPERATION When using Sleep mode, if the next OFF-Timer setting less than 8 hours, Sleep mode will remain active until the OFF-Timer setting. If the next OFF-Timer setting more than 8 hours, it will override the OFF-Timer setting and will turn the system off 8 hours after engaging Sleep mode. Auto Mode (SMART) In Auto Mode (SMART) the system will automatically switch to Cooling, Heating, Dry or Fan Only modes based on the current room temperature.
Air flow direction (Louvers) control OPERATION The louver is operated by a stepper motor and operates the horizontal swing of the louver automatically. Press the SWING button to start or stop the louver swing. During the louver swing in normal operation, the current position will be stored. When the appliance turn off and louver swing automatically to the default position, it will position at the close position plus 5º.
OPERATION Dehumidification mode Dehumidifying area I: Operation at the frequency in the range (30–60Hz) according to DeltaT (difference between ambient and indoor temperature). Dehumidifying area II: The compressor stops for 5 minutes and operators for 5 minutes at the lowest frequency. Dehumidifying area III: The compressor stops.
OPERATION Fan Only Mode Operation In this mode, the compressor and outdoor fan stop, indoor fan operates under the pre-setting of air volume, the louver swing, and the indoor fan speed is defaulted to the current setting in as the Heating Mode. Defrost Conditions for Defrost Activation: The following three conditions must be met to activate Defrost. • Condition 1: Outdoor ambient sensor is below 28.4F • Condition 2: When the heating compressor consecutively runs for 40 minutes .
Control Mode (Indoor Unit Mode Control) OPERATION General Technical Parameters Remote to receiver distance: 26 ft (8m). Remote receiver angle: Less than 80 degrees. Temperature control accuracy: ± 33.8°F (1°C) Time error: Less than 1%. Emergency Switch Pressing the emergency button will activate the automatic mode of operation. Press the button to turn it on and press it again to turn it off.
OPERATION 18K, 24k and 36k Control Mode 1. Cooling Anti-freeze Protection To prevent freezing caused by too low temperature of indoor evaporator, the air conditioner will implement real-time detection over the indoor coil temperature. If the indoor coil temperature is too low, the compressor will be prohibited from increasing or decreasing the frequency or shutting down automatically. 2.
24k and 36k Control Mode OPERATION 7. Outdoor four-way Valve Control Four-way valve of the outdoor machine shuts down when cooling but starts when heating. The operation of heating defrosting refers to defrosting operation and, when the heating remote shutdown, the four-way valve disconnects in 50s when the compressor stops working. 8.
OPERATION 24k and 36k Control Mode Fan Only Mode (1) Outdoor fan and compressor stop. (2) Temperature setting function is disabled, and no setting temperature is displayed. (3) Indoor fan can be set to high/medium/low, but can not be set to auto. Cooling Mode Indoor fan logic: Runs all the time and the speed can be selected as high, (medium), low and auto. The auto fan: T1 is indoor room temperature. Ts is setting temperature.
OPERATION Control Logic Description Heating Mode Indoor fan: The fan of the indoor unit will not run until the heat exchanger of the indoor unit reaches a high enough temperature. This prevents cold air blowing into the space. After the indoor coil reaches adequate temperature, the speed can be selected as high, medium, low, or auto. Auto fan: T1 is indoor room temperature. Ts is setting temperature.
OPERATION Control Logic Description Auto Mode This mode can be chosen with remote controller and the setting temperature can be ). changed between 61°F~86°F(16°C~30 In auto mode, the machi ne will choos e cooling, heatin g or fan-only mode according to Δ T (Δ T =T1 -Ts). Running mode Δ T=T1 -Ts Δ T＞37°F(3 27°F(-3 ) Cooling Fan -only )≤ Δ T≤ Heating ΔT ＜ Indoor fan will run at auto fan of the relevant mode. The louver operates same as in relevant mode.
OPERATION Control Logic Description Condenser High-temperature Protection T3 Off TE1 0 TE1 1 On Conditions: Cooling mode: The outdoor coil temperature (T3) is high than TE7 (logical calculation between 142F and 150F) for 10 seconds, the compressor and outdoor fan will shit off.
Outdoor Units INSTALLATION Fig. 432 Fig.
INSTALLATION 24 and 36k Outdoor Units Piping Work and Refigerant Charge MAX. leng gth allowe d Indoor unit D C Height E Height D B Pipe length D A Pipe length A Outdoor unit Note: Indoor unit D in the circle is only valid for 36K model. *Refrigerant Additional Charge: The unit has been filled with refrigerant, but if L (total pipe length) exceeds standard length, additional refrigerant (R410A) change is required. For 24K: Additional refrigerant charge= (L-74) x 0.
Indoor unit D in the circle is only valid for 36K model. Refrigerant Additional Charge The unit has been filled with refrigerant, but if L (total pipe length) exceeds standard length, additional refrigerant (R410A) change is required. For 24K: Additional refrigerant charge=[L-74-4/5(22.8m) ]× 0.807oz/5ft (15g/m) For 36K: Additional refrigerant charge=[L-98-3/7(30m) ]× 0.
INSTALLATION Leak Check, Evacuation, and Charging (Triple Evacuation) Friedrich requires all installations are Leak Checked and Evacuated in accordance to the “triple evacuation” process. This process promotes a dry tight refrigeration system before opening the service valves. It recommended that a single port refrigeration manifold and hoses rated over 31.5psi be used.
INSTALLATION Leak Check, Evacuation, and Charging (Triple Evacuation) EVACUATE BREAK VACUUM WITH DRY NITROGEN WAIT EVACUATE BREAK VACUUM WITH DRY NITROGEN WAIT EVACUATE CHECK FOR TIGHT, DRY SYSTEM (IF IT HOLDS A VACUUM) CHARGE SYSTEM 136
INSTALLATION Checklist Check Unit following Installation No.
Operation Test INSTALLATION Test Operation System Checks 1. Conceal refrigerant pipes where possible. 2. Make sure drain hose slopes downward along entire length. 3. Ensure all refrigerant pipes and connections are properly insulated. 4. Fasten pipes to outside wall, when possible. 5. Seal and weatherproof wall hole which the interconnecting wires and refrigerant pipes pass through. Perform test operation after completing gas leak and electrical safety check. 1.
INSTALLATION Fresh Air Intake Duct (9K~18K) Indoor unit can take fresh air from the reserved fresh air intake, the size of the fresh air intake hole is 2-1/2 in.(65mm) (9K~18K). Please follow the steps below when needed. 1) Cut off the reserved metal circular hole on the base board. 2) Connect air duct with the fresh air intake.
MAINTENANCE 140
MAINTENANCE Lh Lh The following is a deep cleaning and must be completed by a professional. Usera are strictly forbidden to operate privately, otherwise they will be at their own risk. 0 Cut off the power supply by moving the power switch In the dlnictlon of the arrow. Note: Tum off the appllanoe first before cutting off the power supply. • 1. Ramova the wiring COV&r and the elactrlc■I box cover. 2. Disconnect tha fan motor line and the louver motor line.
MAINTENANCE L'.h L'.h The followlng 18 a deep cleanlng and must be completed by a professlonal. Users ara strlctly forbidden to operate prlvately, otherwise they wlll be at their own risk. Remove the acrews of the air duct. (G poaltlon and H poaltlon) Note: Some models do not have H position screws. A 1. Press the 2 buckles of the air duct to disengage it from 2 down slots of the mounting plate. .:,' 2. Remove the air duct.
R-410A SEALED SYSTEM REPAIR Service Valves Appearance 2-way Valve (Liquid Side) Hexagonal wrench (4mm) Flare nut Open position Closed position To piping connection Shipping 1.
Pumping Down R-410A SEALED SYSTEM REPAIR Liquid side Indoor unit 2-Way valve Open Outdoor unit Gas side 3-Way valve Closed Lo CLOSE CLOSE Purge the air – Do this quickly so that the gauge ends up indicating 0-15 PSI. – Remove the valve stem caps and confirm that the valve stems are in the raised position. – Be sure to use a hexagonal wrench to operate the valve stems. – Tighten the service port nut. – Be sure to check for gas leakage.
R-410A SEALED SYSTEM REPAIR Gas Charging (After Repair) Liquid side Indoor unit 3-Way valve Outdoor unit Open Gas side 3-Way valve Open Lo OPEN CLOSE – Connect the charge hose which you dis-connected from the vacuum pump to the valve at the bottom of the cylinder. – If you are using a gas cylinder, also use a scale and reverse the cylinder so that the system can be charged with liquid. – Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the air.
R-410A SEALED SYSTEM REPAIR Replace 24k Outdoor unit Compressor and Motor Important: Befor e disassembly and assembly, mak e sure that the power to the system has been disconnected and verified as voltage free. Step Handling Instruction 1.Remove external casing 1. Remove the top cover, handle and valve cover; 2. Remove the outer case and right side plate. 2.Remove motor 1. Remove the blade nut and then remove the blade; 2. Remove the motor from motor supporter 3.Remove compressor 4.
R-410A SEALED SYSTEM REPAIR Replace 36k Outdoor unit Compressor and Motor Important: Before disassembly and assembly, make sure that the power to the system has been disconnected and verified as voltage free. Step Handling Instruction 1. Remove external casing 1. Remove the top cover, handle and valve cover; 2. Remove the outer case and right side plate. 2. Remove motor 1. Remove the blade nut and then remove the blade; 2. Remove the motor from motor supporter 3. Remove compressor 4.
R-410A SEALED SYSTEM REPAIR Replace 9k and 12k Duct Type unit Compressor and Motor Removal and Assembly of Fan Motor Important: Before removing the fan, make sure power to the system is disconnected. Step Illustration Handling Instruction 1. Unplug the motor cables. 2. Remove the base board. Use screwdriver to remove the electric box cover and unplug the motor cables in electric box. Loose and take out the screws fixing the base board, then remove the base board. 3.
R-410A SEALED SYSTEM REPAIR Replace 18k Duct Type unit Compressor and Motor Removal and Assembly of F an Motor Important: Before removing the fan, make sure power to the system is disconnected. Step 1. Unplug the motor cables 2. Remove the base board 3. Remov e the screws on fan sub -assembly. Illustration Handlin g Instruction Use screwdriver to remove the electric box cover and unplug the motor cables in electric box.
R-410A SEALED SYSTEM REPAIR Replace 9k, 12k, and18k Cassette Replacement of F an Motor Step 1. Loose n the screws holding condensate pan . Illustration Handli ng Instruction Use screwdriver to loos en the screws holding the drain pa n in place. 2. Remove the condensate pan Carefully remov e the condensate pan. 3. Loose n the bolt holding the fan blade in place Use a wrenc h or socket to carefully remove the fan blade bolt. 4. Remove the fan blade The fan blade ca n now be removed. 5.
R-410A SEALED SYSTEM REPAIR Replace 9k, 12k, and18k Cassette Replacement of F an Motor Step 6. Remove the motor and replac e it 7. Tighten the bolts holding the motor Illustration Handli ng Instruction Remove the motor and replace it. Use socket a wrench to or carefully tighten the motor bolts. 8. Mount the fan blade and tighten the bolt Mount the fan blade and use a wrenc h or socket to carefully tighten the bolt holding the fan blade in place. D o not overtighten as dam age may occur. 9.
R-410A SEALED SYSTEM REPAIR Replace 9k, 12k, and18k Cassette Removal and Installation of Condensate Pump Illustration Step 1. Loose n the screws holding condensat e pan . 2. Remove the condensate pan . 3. Pull out the water outlet pipe . 4. Lo osen the screws holding the condensat e Handli ng Instruction Use screwdriver to loosen the screws holding drain pan in place. Carefully remove the condensate pan. Pull out the water outlet Pipe. Lo osen the screws holding the condensate pump . pump .
R-410A SEALED SYSTEM REPAIR Replace 24k and 36k Cassette Compesdsor and Motor Step 153 Illustration Handling Instruction 1. Loosen the screws holding the electric box cover and electric box. Use screwdriver to loosen the Electric box. 2. Loosen the screws holding condensat e pan and Remove the condensate pan. Use screwdriver to loosen the screws holding the drain pan in place. 3. Loosen the bolts holding the fan blade s in place and Remove the fan blade.
COMPONENTS TESTING Resistance Table Of Indoor Coil And Indoor Room Sensor The Parameter Of The Outdoor Coil And Outdoor Sensor: R(0)=15k B(0/100)=3450 Temp. (°F) Resistance (kΩ) Voltage Temp. (°F) Resistance (kΩ) Voltage Temp. (°F) Resistance (kΩ) Voltage -4 38.757 0.58143512 64.4 7.051 2.09859271 132.8 1.877 3.654865988 -2.2 36.844 0.60795346 66.2 6.778 2.14682606 134.6 1.818 3.686036427 -0.4 35.038 0.63530819 68 6.516 2.19524793 136.4 1.76 3.717201166 1.4 33.331 0.
COMPONENTS TESTING Resistance Table Of Outdoor Compressor Temperature Sensor R(0)=187.25k B(0100)=3979 Temp. (°F) Resistance (kΩ) Voltage Temp. (°F) Resistance (kΩ) Voltage Temp. (°F) Resistance (kΩ) Voltage -4 542.867 0.06185563 64.4 78.854 0.39694585 132.8 6.624 2.532777116 -2.2 512.839 0.06543004 66.2 75.381 0.41372093 134.6 6.414 2.573028606 -0.4 484.672 0.06917993 68 72.082 0.43102355 136.4 6.212 2.612972641 1.4 458.239 0.07311215 69.8 68.948 0.44885674 138.
COMPONENTS TESTING OUTDOOR COMPRESSOR DISCHARGE TEMPERATURE （R 0 =187.25K±6.3% ；R 100 =3.77K±2.5K ；B0/100=3979K±1% ） T [°F ] -22 -20 -18 -17 -15 -13 -11 -9 -8 -6 -4 -2 0 1 3 5 7 9 10 12 14 16 18 19 21 23 25 27 28 30 32 34 36 37 39 41 43 45 46 48 50 52 54 55 57 59 61 63 64 156 T [ oC] -30 -29 -28 -27 -26 -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 R min [ KΩ ] 908.2603 855.3955 805.9244 759.6097 716.2320 675.
COMPONENTS TESTING T [°F ] 66 68 70 72 73 75 77 79 81 82 84 86 88 90 91 93 95 97 99 100 102 104 106 108 109 111 113 115 117 118 120 122 124 126 127 129 131 133 135 136 138 140 142 144 145 147 149 151 153 154 156 158 160 162 163 165 157 T [ oC] 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 R min [ KΩ ] 71.2227 68.1036 65.1373 62.3155 59.6306 57.0752 54.6424 52.3258 50.1192 48.0168 46.
COMPONENTS TESTING T [°F ] 167 169 171 172 174 176 178 180 181 183 185 187 189 190 192 194 196 198 199 201 203 205 207 208 210 212 214 216 217 219 221 223 225 226 228 230 232 234 235 237 239 241 243 244 246 248 250 252 253 255 257 259 261 262 264 266 158 T [ºC ] 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 R min [ KΩ ] 8.0951 7.8290 7.5730 7.3264 7.
COMPONENTS TESTING AMBIENT AIR SENSOR IN INDOOR AND OUTDOOR UNIT ： （R 0 =15K±2% ；B0/100=3450K±2% ） T [°F ] -22 -20 -18 -17 -15 -13 -11 -9 -8 -6 -4 -2 0 1 3 5 7 9 10 12 14 16 18 19 21 23 25 27 28 30 32 34 36 37 39 41 43 45 46 48 50 52 54 55 57 59 61 63 64 66 68 70 72 159 T [ºC ] -30 -29 -28 -27 -26 -25 -24 -23 -22 -21 -20 -19 -18 -17 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 R min [ KΩ ] 60.78 57.75 54.89 52.19 49.63 47.21 44.92 42.
COMPONENTS TESTING T [°F ] 73 75 77 79 81 82 84 86 88 90 91 93 95 97 99 100 102 104 106 108 109 111 113 115 117 118 120 122 124 126 127 129 131 133 135 136 138 140 142 144 145 147 149 151 153 154 156 158 160 162 163 165 167 169 171 172 160 T [ °C ] 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 R min [ KΩ ] 5.667 5.449 5.240 5.048 4.864 4.687 4.517 4.355 4.198 4.048 3.904 3.766 3.
COMPONENTS TESTING T [°F ] 174 176 178 180 181 183 185 187 189 190 192 194 196 198 199 201 203 205 207 208 210 212 214 216 217 219 221 223 225 226 228 230 232 234 235 237 239 241 243 244 246 248 161 T [ ºC ] 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 R min [ KΩ ] 0.8570 0.8316 0.8071 0.7834 0.7604 0.7382 0.7167 0.6958 0.6755 0.6560 0.6371 0.6188 0.6011 0.5840 0.5674 0.5514 0.5359 0.5209 0.5064 0.
Compressor COMPONENTS TESTING OVERLOAD PROTECTION POWER DC INVERTER & CONTROLLER R( U) S( V) T( W) Resistance Test. The compressor is at fault if the resistance of winding is 0 (short circuit)or ∞ open circuit. Common signs compressor is faulty: • Compressor motor lock. • Discharge pressure value approaches static pressure value . • Compressor motor winding abnormality. Note: • Don’t put a compressor on its side or turn over. • Assemble the compressor quickly after removing the plugs.
Fan Motor 163 COMPONENTS TESTING
Fan Motor COMPONENTS TESTING Resistance Test. Test the resistance of the main winding. The indoor fan motor is faulted if the resistance of main winding 0 (short circuit)or ∞ open circuit. DC Voltage test Manually rotate indoor fan motor slowly for several revolutions, and measure voltage “YELLOW” and “GND” on motor. The voltage repeats 0V DC and 5V DC. Notes: • Do not hold motor by lead wires. • Do not connect or disconnect the molex connecter while power ON. • Do not drop motor against hard material.
COMPONENTS TESTING Test Fan Motor and Compressor (Outdoor 24k and 36k) Fan motor ompressor Power DC Inverter & Controller Compressor 165
COMPONENTS TESTING Test Fan Motor and Compressor Test the resistance of the winding. The compressoris faulted if the resistance of winding is 0(short c ircuit)or∞（open circuit ） Typical Symptoms 1) Compressor motor lock. 2) Discharge pressure value approaches static pressure value . 3) Compressor phases are not equal (+/- 0.1Ohm). Notes 1) Do not put a compressor on its side or turn over. 2) When changing compressor, do not leave exposed to ambient conditions for longer than needed.
COMPONENTS TESTING Check Refrigerant System (Outdoor 24k and 36k) TEST SYSTEM FLOW Conditions: ① Compressor is running. ② Th e air condition should be in stalled in good ventilation. Tool: Pressure Gauge Technique: ① see ② feel ③ test SEE FEEL TEST heating run cooling run Pressure gauge Pressure gauge Pressure gauge 167 ----- Tube defrost. ----- The difference between tube’s temperature. ----- Test pressure.
COMPONENTS TESTING Test System Flow (Outdoor 24k and 36k) Cooling mode NO Test system pressure.Does the low pressure normal at service part ? The pressure on the high side. Recharge refrigerant after air purging with the vacuum pump.Does the low pressure nomal over again? The pressure on the low side. NO If the pressure is close to static pressure? yes The system wants refrigerant.The service people must be ration refrigeran.Is the low pressure rise ? yes Air remaining at the refrigerant system.
Check Fuse and Capacitor COMPONENTS TESTING Checking continuity of fuse on PCB ASS’Y. Remove the PCB ASS’Y from the electrical component box. Then pull out the fuse from the PCB ASS’Y (Fig.1) Fuse PCB Ass'Y Fig.1 2) Check for continuity by a multimeter as shown in Fig.2. Fuse Fig.2 .CAPACITOR 1) Remove the lead wires from the capacitor terminals, and then place a probe on the capacitor terminals as shown in Fig.3.
COMPONENTS TESTING 7k Indoor Wall Mount Printed Circuit Board 1 Interface of PG motor 2 Room temperature sensor 3 Pipe temperature sensor 4 Switch button 5 Feedback from PG motor 6 Up＆down swing 7 Left＆right swing 8 Wiring control or wifi interface 9 Display interface 10 Protective tube Figure 701 7k Indoor Unit Printed Circuit Board Identification Figure 702 7k Indoor Unit Printed Circuit Board Identification 170 1 Interface of PG motor 2 Room temperature sensor 3 Pipe temperat
COMPONENTS TESTING Ducted units and Cassettes Printed Circuit Board (Indoor Units) Duct 9K~18K Hea t Output1 Step Motor Ambient Temp Coil Temp Water level switch DC Fan Humidity YL Swin g Wifi Pump Wired Output2 DISP DISP Nano L、N Power Input Out Cassette 9K~36K AC P ower Filter Main control component code DC motor Pump motor Swing motor Water Level Switch EE Display WIFI Wired control Electric Heater Communication with outdoor unit 171 Switching Power Supply MCU&CPU Out Inpu
COMPONENTS TESTING 24 Main Printed Circuit Board 24k Outdoor 24 s s sensor 24k Outdoor Drive Printed Circuit Board 172 sensor / / sens or sens or n n
COMPONENTS TESTING 36K Printed Circuit Board 36k Outdoor Main Main control board LiqA /GasA /LiqB /Gas overheat Main control board B sensor protection switch LiqA /GasA Compressor /LiqB /Gas overheat B sensor High protection pressure switch switch LiqC /GasC /LiqD /Gas D sensor 36K Compressor LiqC /GasC /LiqD /Gas D sensor Electronic expansion valve A Electronic expansion valve A Electronic expansion valve C Electronic expansion valve C IPM-SI IPM-SI Electronic expansion valve B Electronic DC -FAN
COMPONENTS TESTING Field Settings (ESP Setting) Duct Type Only The static pressure can be freely adjusted by using specific wire remote controller. Error Indicator LCD Parameter Code Function Code Model (Capacity Btu/h) The range of static pressure Function code set 9K/12K/18K 0-0.015 in.Hg (0-50Pa) 0-50, more than 50 is 0.015 in.Hg (50 Pa), [default: 0 (0 in.Hg or 0Pa)] YXE-C01U(E)/YXE-C02U(E) Static pressure setting: 1 Hold down both“MODE”button and“ADD.FUNC.
COMPONENTS TESTING Field Settings (Indoor Unit Parameter Revision) 1. Connect wire remote controller with indoor unit Step 1: Removing the upper cover of the wired controller Upper cover of the wired controller Screw driver Lower cover of the wired controller Insert a normal screw driver into the position, and gently rotate it. In this way, the upper cover can be easily removed. Note: Control board of the remote controller is placed on upper co ver.
COMPONENTS TESTING Field Settings (Indoor Unit Parameter Revision) PAR AME TE R CO DE PAR AME TE R VALUE &R E PR E S E NTATIO N D ATA R E PR E SE NTATIO N TY PE (FUNC TIO N C O D E ) 0：Cancel Self Recovery of Power Break function ； Integer 1：Self Recovery of Power Break ； others：invalid 0：Centigrade Temperature ； 1：Fahrenheit Temperature ； Integer others：invalid 0：Default display set temperature ； 1：Default display room temperature ； Integer others：invalid 1 Self Recovery of Power Break 2 Temperature
COMPONENTS TESTING Field Settings (Running Parameter Query) Running Parameter Query Running parameters can be referred to by digital tube switch or specified wired remote control. Operation: 1. Connect wired remote controller with indoor unit (same method as indoor parameter revise. 2. Changing system parameter. O PE R ATIO N: and parameter ① Hold down both “MO DE ” button and “ADD.FUNC .” button for 3 seconds, symbol number blinking at the same time.
COMPONENTS TESTING Field Settings (Running Parameter Query) D igital D isplay Switch Introduction It can be used to check outdoor running parameters. There are 3 buttons on the digital display board ： 1） SWITCH button ：Indoor parameters and outdoor parameters can be selected in turn by pressing it. “P.”-outdoor unit parameter , “H.
COMPONENTS TESTING Field Settings (Running Parameter Query) Parameters can be checked as following table below. Parameter code 0 179 D escriptions Protect Code or Fault code P.1 Target Frequency P.2 Driving Frequency P.4 Outdoor EEV Opening P.5 Outdoor EEV Target Opening P.6 Upper DC Motor Revolving Speed P.8 AC Input Voltage P.9 Current P.10 Modular Temperature P.11 Capacity Needed P.12 Modular Fault P.20 Outdoor Ambient Temperature P.21 Outdoor Coil Temperature P.
COMPONENTS TESTING Field Settings (Function Settings) Instructions for the function setting of acces s control, fire protection , ON/OFF 1. Factory setting ON/OFF function is disabled a s factory default while both the access control and fire protectio n functions are enabled. To use or cancel the ac cess control /fire protection /(ON/O FF ) function , use the wired controller to modify the parameter s of indoo r unit.
COMPONENTS TESTING Field Settings (Function Settings) 1) When using the do or lock function, the red wire should be c ut and connect ed to the door lock control switch attached t o it (supplied by user), an d the connecting wire should be 22AWG or ab ove. In normal conditions, the unit op erates normally on ce the switch is closed a nd shuts do wn once the switch is off.
COMPONENTS TESTING Field Settings (Outdoor 24k and 36k) DIP Settings Dip Switch Setting of Outdoor Unit Mark of " " indicates the position of dip switches. Switch is valid when is ON. function By default se tting is OFF. OFF ----normal mode ON ----refrigerant collection mode When the power is ON, the dial changed from OFF to ON, enters into refrigerant collection mode.
COMPONENTS TESTING Field Settings (Outdoor 24k and 36k) Running Parameter Query Outdoor Running parameters can be checked by 7 segment display. 7 segment display Digital Display Switch Outdoor control board ● ● ● S2 S1 Select S3 Increase Decrease There are 3 buttons on the digital display board ： 1) Sel ect button: Select to display outdoor/indoor unit parameter. "P." -- Parameter of outdoor unit "A." -- Parameter of indoor unit A "b." -- Parameter of indoor unit B "C.
COMPONENTS TESTING Field Settings (Outdoor 24k and 36k) 184 Paramet er P.0 P.1 P.2 P.4 P.5 P.6 P.7 P.8 P.9 P.10 P.11 P.12 P.13 P.14 P.15 P.16 P.17 P.18 P.20 P.21 P.22 P.23 A.1 A.2 A.4 A.5 A.6 A.7 A.8 A.9 A.10 A.11 B.1 B.2 B.4 B.5 B.6 B.7 B.8 B.9 B.10 B.11 C.1 C.2 C.4 C.5 C.6 C.7 C.8 C.
Unit A actual suction overheating A.11 B.1 Unit B fault codes B.2 Unit B valve actual opening B.4 Unit B liquid pipe temperature B.5 Unit B gas pipe temperature B.6 Unit B coil temperature B.7 Unit B ambient temperature B.8 Unit B set temperature Field Settings (Outdoor 24k and 36k) B.9 Unit B capacity B.10 Unit B set fan speed suction overheating B.11 er Unit B ac tualDescriptions Paramet C.1 Unit Ccodes fault codes P.0 Fault C.2 Unit C valve actual frequency opening P.1 Compressor C.
TROUBLESHOOTING Test the jumper terminals Note: When the whole machine is powered up, if the external unit does not work, to rule out the communications failures, adopt screening method such as short circuit on the jumper terminals to see if the external unit can be started normally or similar method. There are two blue terminals on the outdoor control panel, as shown above. Application: Short out the terminals, and power up the outdoor unit, then the outdoor unit may run independently.
Protection Circuit Fault Isolation TROUBLESHOOTING Protection diagnosis of the complete machine (all types of protection during operation, i.e. under-voltage, over-voltage and overcurrent protection) Note:List all types of protection that may occur to the complete machine and describe the conditions and signs of the start, course and end of such protection. Voltage protection Protection against AC input over-voltage/under-voltage 1.
Compressor Fault Isolation TROUBLESHOOTING Judging the connecting terminals of inverter compressor: It is impossible to identify terminals U, V and W of inverter compressor with multi-meter. Just connect the terminals in the same way as the original unit when replacing the compressor. A wrong connection will lead to reverse and loud noise of the compressor.
TROUBLESHOOTING Fault Codes (2) Fault codes indicated by LED lamps on display panel Lorem ipsum Lamp RUN(LED2 ,red) and Lamp DEFROS T（LED5 ,green）flashing ，Lamp RUN display fault code ten digit number, lamp DEFROST disp lay fault code single digit number (as shown fig. below). Fo r example ，fault code 36: led R UN & defrost flash 3 times at the same time, and led DEFROST continue flash 3 times,repor ts No. 36 fault.
TROUBLESHOOTING The following is the fault code table of indoor. Indoor Fault Code Sheet 2 Indoor Fault code Fault code 51 55 Fault Description D rainage protection Possible Reason of Abnormality 1.1 Check whether there are something to block the drain hose or the height of the 1. The water level of the drain drain hose is too high; pan exceed safe level; 1.2 Check the water pump and 2. The cable of the water level replace the water pump if switch connect loose; the water pump is failure; 3.
Indoor Fault Code Fault code 74 81 83 Fault Description Indoor EEPROM Data 2 error Indoor ambient Temperature Sensor Fault E vaporator Middle Temperature Sensor Fault TROUBLESHOOTING Possible Reason of Abnormalit y EE in MCU is failure, the unit can run, but the function user has set is ineffective. 191 Replace EE data in MCU. 1. The cable of the room 1. Reconnect the cable of the temperature sensor connect room temperature sensor; loose; 2. Replace the room temperature sensor; 2.
TROUBLESHOOTING 18K, 24k and 36k outdoor Fault Codes Trouble Shooting Guide When the air conditioner failure occurs, the fault code will displays on control board. Ma in control failure Fault code will display on 7 segment display on outdoor c ontrol board. Drive fault code display The lamp of drive board flash shows failure occur. The drive failure lamp flicking times shows the failure code. Drive board Drive failure lamp The drive failure lamp flicking times shows the failure code.
TROUBLESHOOTING 18K, 24k and 36k outdoor Fault Codes 13 .2 Fa ult codes The following is the fault code table of outdoor. Sheet 1 Outdoor Fault Code Fault code Possible R eason of Abnormality 1 Outdoor ambient temperature sensor fault 1.The outdoor ambient temperature sensor connect loose; 2.The outdoor ambient temperature sensor is failure; 3.The sampling circuit is failure 2 Outdoor coil temperature sensor fault 1.The outdoor coil temperature sensor connect loose; 2.
TROUBLESHOOTING 18K, 24k and 36k outdoor Fault Codes Fault code Possible R eason of Abnormality voltage absent phase Three-phase power is abnormal; The outdoor wiring connect wrong; The outdoor control board is failure. 13 Compressor overheat protector device 1. The wiring of the overload protector connect loose. 2. The overload protector is failure . 3. The refrigerant is not enough; 4. The installation pipe is too long than normal, but not add the enough refrigerant; 5.
TROUBLESHOOTING 18K, 24k and 36k outdoor Fault Codes Fault code 195 Fault D escription 24 Expansion valve B (thin)tube sensor fault 25 Expansion valve C (thin)tube sensor fault 26 Expansion valve D (thin)tube sensor fault 27 Expansion valve A （ thick tube）sensor fault 28 Expansion valve B （ thick tube） sensor fault 29 Expansion valve C (thick tube) sensor fault 30 Expansion valve D (thick tube) sensor fault 45 IPM fault Possible Reason of A bnormality How to Deal W ith 1.
TROUBLESHOOTING 18K, 24k and 36k outdoor Fault Codes Fault code 46 Possible R eason of Abnormality 1.The cable between the control board and the driver board connect loose; IPM and control board 2.The cable between the control communication fault board and the driver board is failure; 3.The driver board is failure ； 4.The control board is failure. Discharge temperature too high fault 1. The refrigerant of the unit is not enough; 2.
TROUBLESHOOTING 18K, 24k and 36k outdoor NOTE 1: If the indoor unit can not turn on or the indoor unit turns itself off after 30s, and at the same time the unit does not display the fault code, please check the fire and the socket of the control board. Note 2: If the indoor unit display the 75,76,77,78 fault code after you turn on the unit, please check the TEST seat of the indoor control board or the TEST detection circuit whether exists short circuit.
18K, 24k and 36k outdoor TROUBLESHOOTING 5 Fault code 1 Fault Description Possible Reason 4. 5. How to De al With of Abnormality 1. 2. 3. 4. 5. 6. 2 3 4 5 6 7 11 1. 12 13 14 15 198 2. 3.
TROUBLESHOOTING 18K, 24k and 36k outdoor Fault code Fault Description too low 199 Possible Reason of Abnormality How to De al With
7k Wall Units 200 WIRING DIAGRAMS
WIRING DIAGRAMS 6 6 5 1 1 2 2 3 3 4 4 5 Ducted Indoor Units 9k, 12k, and 18k 1 1 2 2 3 3 4 4 1 1 2 2 3 3 1 1 2 2 3 3 4 4 1 1 2 2 3 3 4 4 1 2 3 4 1 2 3 4 Remark: Dashed parts are not available in some models. Details see the table below.
WIRING DIAGRAMS 9k-36k Indoor Cassette Units 1 1 2 2 3 3 4 4 1 1 2 2 3 3 4 4 1 1 2 2 3 3 4 4 Remark: Dashed part s are not available in some models. Details see the table below.
WIRING DIAGRAMS Electric wiring diagram 1993419.
36k Outdoor Units 204 WIRING DIAGRAMS
18K Outdoor Condensor 205 PARTS CATALOG
18K Outdoor Condensor 206 PARTS CATALOG
18K Outdoor Condensor 207 PARTS CATALOG
PARTS CATALOG 18K Outdoor Condensor FIGURE 902 208 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67401011 Fan Guard FPHMR18A3A 1 2 67401012 Panel FPHMR18A3A 1 3 67401013 Hex Nuts FPHMR18A3A 1 4 67401014 Propeller Fan Blade FPHMR18A3A 1 5 67401015 Axis Sheath FPHMR18A3A 1 6 67400296 DC Motor FPHMR18A3A 1 7 67401016 Motor Supporter FPHMR18A3A 1 8 67401017 Connecting Board FPHMR18A3A 1 9 67401018 Upper Board FPHMR18A3A 1 10 67401019 Back Guard FP
PARTS CATALOG 18K Outdoor Condensor FIGURE 902 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 38 67401043 Radiator FPHMR18A3A 1 39 67401044 Electric Box FPHMR18A3A 1 40 67401045 Terminal Connecting Board FPHMR18A3A 1 41 67400365 Connection Terminal Panel FPHMR18A3A 1 42 67401046 Diplay Mounting Plate FPHMR18A3A 1 43 67401047 Power Terminal Panel FPHMR18A3A 1 44 67401048 Display Board FPHMR18A3A 1 45 67400377 Discharge, Suction, Coil and Air Temperature Sensor
24K Outdoor Condensor PARTS CATALOG Figure 901A 210
24K Outdoor Condensor PARTS CATALOG E -6 1 6 E -6 1 6 Figure 901B 211
24K Outdoor Condensor PARTS CATALOG B -3× 14 C-4 × 12 A-4× 12 D-4 × 25 A-4 × 12 Figure 901C 212
24K Outdoor Condensor PARTS CATALOG FIGURE 902 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400388 fan guard FPHMR24A3A 1 2 67400336 front panel FPHMR24A3A 1 3 67400337 Left guard filter FPHMR24A3A 1 4 67400998 mounting plate FPHMR24A3A 1 5 67400999 Welding hex nuts FPHMR24A3A 1 6 67400340 propeller fan FPHMR24A3A 1 7 67400341 FAN MOTOR FPHMR24A3A 1 8 67400342 motor bracket FPHMR24A3A 1 9 67400343 upper cover FPHMR24A3A 1 10 67400344 back guar
24K Outdoor Condensor PARTS CATALOG FIGURE 902 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 38 67400932 discharge tube assy FPHMR24A3A 1 39 67400369 4-way valve assembly FPHMR24A3A 1 40 67400933 mounting plate FPHMR24A3A 1 41 67400370 Driver board FPHMR24A3A 1 42 67400371 Outdoor Main Control Board Component FPHMR24A3A 1 43 67400372 Filter board FPHMR24A3A 1 44 67400934 elec joint box assy FPHMR24A3A 1 45 67400373 Aluminum electrolytic capacitor FPHMR24A3A
36K Outdoor Condensor PARTS CATALOG Figure 902A 215
36K Outdoor Condensor PARTS CATALOG Figure 902B 216
36K Outdoor Condensor PARTS CATALOG 56 Figure 902C 217
36K Outdoor Condensor PARTS CATALOG FIGURE 902 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400380 Guard Filter FPHMR36A3A 1 2 67400381 Upper Board FPHMR36A3A 1 3 67401232 Motor Supporter FPHMR36A3A 1 4 67400383 DC Motor FPHMR36A3A 1 5 67400384 Propeller Fan Blade FPHMR36A3A 1 6 67400385 Welding Hex Nuts FPHMR36A3A 1 7 67400386 Mounting Plate FPHMR36A3A 1 8 67400387 Left Guard FPHMR36A3A 1 9 67401007 Handle FPHMR36A3A 1 10 67400388 Fan Guard
36K Outdoor Condensor PARTS CATALOG FIGURE 902 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 34 67400944 Base Holder Part FPHMR36A3A 1 35 67400945 Mounting Plate FPHMR36A3A 1 36 67400400 Crankcase Heater FPHMR36A3A 1 37 67400401 Noise-Insulation Cotton FPHMR36A3A 1 38 67400946 supporting component FPHMR36A3A 1 39 67400922 fixed board FPHMR36A3A 1 40 67400402 Tube type electric heater FPHMR36A3A 1 41 67400361 Pressure Switch FPHMR36A3A 1 42 67400362 Pres
7k Wall Mounted Indoor Unit PARTS CATALOG ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400571 1959683 - installation plate FPHMW07A3A 1 2 67400572 1959764 - Supporting button FPHMW07A3A 1 3 67400573 2008502 - Refrigeration system FPHMW07A3A 1 4 67400154 1466014 - cross-flow fan blade FPHMW07A3A 1 5 67400155 1223739 - bearing FPHMW07A3A 1 6 67400466 1964935 - baffle FPHMW07A3A 1 7 67400576 1965029 - Air Duct Assembly FPHMW07A3A 1 8 67400577 1959767 - she
7k Wall Mounted Indoor Unit PARTS CATALOG ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 21 67400588 4113865 - panel FPHMW07A3A 1 22 67400589 1964953 - Motor bracket FPHMW07A3A 1 23 67400590 1964954 - motor cover FPHMW07A3A 1 24 67400591 1964950 - center staff FPHMW07A3A 1 25 67400592 1964956 - motor cover FPHMW07A3A 1 26 67400174 1260259 - Step motor FPHMW07A3A 1 27 67400550 1964955 - Motor bracket FPHMW07A3A 1 28 67400595 1467336 - Step motor FPHMW07A3A 1
9K, 12K Indoor Cassette PARTS CATALOG B-M4x08 • Figure 904 222
9K, 12K Indoor Cassette ITEM PART NUMBER PARTS CATALOG PART DESCRIPTION USED ON MODEL QTY FIGURE 904 1 67400976 Air guiding plate FPHC09A3A, FPHC12A3A 1 2 67400977 Water drain tube FPHC09A3A, FPHC12A3A 1 3 67400425 Centrifugal fan blade FPHC09A3A, FPHC12A3A 1 4 67400426 DC motor FPHC09A3A, FPHC12A3A 1 5 67400843 Fixed board FPHC09A3A, FPHC12A3A 1 6 67400422 Evaporator assembly FPHC09A3A 1 6A 67400427 Evaporator assembly FPHC12A3A 1 7 67400844 Screws FPHC09A3A, FPH
PARTS CATALOG 18K Indoor Cassette 1 � ---- 16 I _______ 1 �c=) : - 22 I 4 A-4X8 _,,,, 9 20 5X53 19 23 �/if:-�t �I A-4 X8 14 i I 224Bolt, Washer Combinations 8 NOTE, Hexagon Head Tapping Screw A-4X12 18 17 11 13 Pan Head Tapping Screw C 10 E Hex Flange Self-tapping Screws F Nut The unicromated coating is applied to iron and steel material for the unspecified materials of the bolt and screw.
18K Indoor Cassette ITEM PART NUMBER PARTS CATALOG PART DESCRIPTION USED ON MODEL QTY FIGURE 905 1 67400872 Base FPHC18A3A 1 2 67400984 Air Duct Plate FPHC18A3A 1 3 67400438 Fan Motor FPHC18A3A 1 4 67400985 Side Panel FPHC18A3A 1 5 67400986 Fan Snail Shell FPHC18A3A 1 6 67400439 Pump Motor FPHC18A3A 1 7 67400987 Cover FPHC18A3A 1 8 67400440 Drainage Hose FPHC18A3A 1 9 67400441 Centrifugal Fan FPHC18A3A 1 10 67400442 Water Collecting Box FPHC18A3A 1 11
PARTS CATALOG 24K INDOOR CASSETTE 4 _ _,,, ==== -=r= 1------: I I �· � @ -=--�t : I : 0 5X53 19 i I I A-4X12 11 1 A-4X8 NOTE, 226 13 FIgure 906 9 A-4X10
24K INDOOR CASSETTE PARTS CATALOG Figure 906 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400872 Base FPHC24A3A 1 2 67400984 Air Duct Plate FPHC24A3A 1 3 67400438 Fan Motor FPHC24A3A 1 4 67400985 Side Panel FPHC24A3A 1 5 67400986 Fan Snail Shell FPHC24A3A 1 6 67400439 Pump Motor FPHC24A3A 1 7 67400987 Cover FPHC24A3A 1 8 67400440 Drainage Hose FPHC24A3A 1 9 67400441 Centrifugal Fan FPHC24A3A 1 10 67400442 Water Collecting Box FPHC24A3A 1 11
9K, 12K, DUCTED INDOOR PARTS CATALOG Figure 907a 228
9K, 12K, DUCTED INDOOR PARTS CATALOG Figure 907b 229
9K, 12K, DUCTED INDOOR PARTS CATALOG Figure 907c 230
PARTS CATALOG 9K, 12K DUCTED INDOOR Figure 907 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400885 Base Plate FPHD09A3A, FPHD12A3A 1 2 67400886 Bottom Plate FPHD09A3A, FPHD12A3A 1 3 67400887 Water Drain FPHD09A3A, FPHD12A3A 1 4 67400409 Evaporator FPHD09A3A, FPHD12A3A 1 5 67400902 Supporting FPHD09A3A, FPHD12A3A 1 6 67400889 Electric Box Cover FPHD09A3A, FPHD12A3A 1 7 67400904 Seal Plate FPHD09A3A, FPHD12A3A 1 8 67400891 Rght Side Board FPHD09A3A, FPHD
18K Ducted Indoor PARTS CATALOG Figure 908a 232
18K Ducted Indoor PARTS CATALOG Figure 908b 233
18K Ducted Indoor PARTS CATALOG Figure 908c 234
PARTS CATALOG 18K Ducted Indoor Figure 908 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400899 Base Plate FPHD18A3A 1 2 67400900 Bottom Plate FPHD18A3A 1 3 67400901 Water Drain FPHD18A3A 1 4 67400412 Evaporator FPHD18A3A 1 5 67400902 Supporting FPHD18A3A 1 6 67400889 Electric Box Cover FPHD18A3A 1 7 67400904 Seal Plate FPHD18A3A 1 8 67400891 Rght Side Board FPHD18A3A 1 9 67400414 Water Position Switch FPHD18A3A 1 10 67400415 Temperature Sensor
24k Ducted Indoor ...--..._. 236 PARTS CATALOG _ .................,......._...................,,........
24k Ducted Indoor PARTS CATALOG ,_-...._. __lllfllllllllllalll ......... l:rla ........ ,_..fllll .....
24k Ducted Indoor PARTS CATALOG ·- A __._,._ C llillllp_,___ � ........ .-........111••11111111111A11............ _...
PARTS CATALOG 24k Ducted Indoor Figure 909 ITEM PART NUMBER PART DESCRIPTION USED ON MODEL QTY 1 67400952 Base Plate FPHD24A3A 1 2 67400953 Base Holder FPHD24A3A 1 3 67400954 Water Drain FPHD24A3A 1 4 67400955 Rubber Plug FPHD24A3A 1 5 67400956 Evaporator assembly FPHD24A3A 1 6 67400957 Supporting FPHD24A3A 1 7 67400958 Outlet Flange Border FPHD24A3A 1 8 67400959 Supporting FPHD24A3A 1 9 67400960 Supporting FPHD24A3A 1 10 67400961 Tie-in FPHD24A3A 1 1
APPENDIX Appendix 1: Reference Sheet of Celsius and Farenheit . 240 Fahrenheit display temperature Fahrenheit 61 62/63 64/65 66/67 68 60.8 62.6 64.4 66.2 68 Fahrenheit display temperature Fahrenheit 32/33 34/35 36 37/38 39/40 41/42 43/44 45 46/47 48/49 50/51 52/53 54 32 33.8 35.6 37.4 39.2 41 42.8 44.6 46.4 48.2 50 51.8 53.6 Celsius 16 17 18 19 20 Celsius 0 1 2 3 4 5 6 7 8 9 10 11 12 Fahrenheit Fahrenheit display Celsius temperature 69/70 71/72 73/74 75/76 77 69.8 71.6 73.4 75.
APPENDIX Appendix 2: Pipe Expanding Method Pipe Pipe cutter Leaning A:Cut the pip Confirm the pipe length according to the distance of indoor unit and outdoor unit. Cut the required pipe with pipe cutter. B:Remove the burrs Remove the burrs with shaper and prevent the burrs from getting into the pipe.
ACCESSORIES CONTROLLER FPWC1 Wired wall controller option for Floating Air Premier and Pro Single/Multizone CEILING CASSETTE GRILLES (REQUIRED ACCESSORY) Required decorative grille for ceiling cassette models Decorative Grille FPCG0912 FPHFC09A3A, FPHFC12A3A 242 FPCG182436 FPHFC18A3A, FPHFC24A3A Decorative Grille DCG2436 MC24Y3J MC36Y3J
Friedrich Air Conditioning Company 10001 Reunion Place, Suite 500 San Antonio, TX 788.5 31.5-541-6645 www.friedrich.com FLOATING AIR DUCTLESS SPLIT SYSTEMS LIMITED WARRANTY 1. A) FIVE YEAR WARRANTY - FRIEDRICH AIR CONDITIONING CO.
CUSTOMER SATISFACTION and QUALITY ASSURANCE Friedrich is a conscientious manufacturer, concerned about customer satisfaction, product quality, and controlling warranty costs. As an Authorized Service Provider you play a vital role in these areas. By adhering to the policies and procedures you provide us with vital information on each warranty repair you complete.
