Service and Parts Manual (2018, 2019, 2020, 2021, 2022)

47 PB
INSTALLATION
Install WRT2 Wireless Programmable Thermostat
NORMAL OPERATION
CHANGING MODE
• Press MODE button to initiate mode selection menu
• Press MODE button until desired system mode is blinking. After 2 seconds of no button press desired mode is selected
CHANGING SET TEMPERATURE
• Ensure thermostat is in correct system mode (Heat, Cool or Auto)
• Press UP or DOWN button. New set temperature will be displayed in large digits. After 2 seconds of no button press new set
temperature is selected
• If Programming mode is OFF, then new set temperature will be held indenitely. If programming mode is ON (see below),
then new set temperature will be held until next scheduled set-point change
CHANGING FAN SPEED
• Press FAN button to initiate fan speed selection menu
• Press FAN until desired fan mode is selected. After 2 seconds of no button press desired fan mode is selected
• AUTO: fan operates as needed during a call for heating or cooling activation only.
• LOW: fan operates continuously in low speed. Heat/Cool will turn on/off in background as needed.
• HIGH: fan operates continuously in high speed. Heat/Cool will turn on/off in background as needed.
SETTING A KEYPAD / FRONT PANEL LOCKOUT
• While in any normal operating mode except OFF, a keypad lockout can be introduced which will prevent any mode change,
fan change or temperature adjustment from being made by the user. Even when locked, any button press will illuminate the
display backlight.
• To activate (and deactivate) the keypad lockout, set thermostat to heat, cool or auto mode then hold FAN + UP buttons for 5
seconds. When the keypad is locked, a padlock will appear in the lower left corner of the display.
SET CLOCK AND TEMPERATURE PROGRAM SCHEDULE
• NOTE: After 60 seconds with no button presses thermostat will exit the settings menu
• Set thermostat to OFF mode and hold MODE + UP buttons for 5 seconds. From this point you have the following options
• Set thermostat real-time clock
• Set a heat schedule
• Set a cool schedule
• Use UP or DOWN buttons until desired section is blinking. Press MODE to enter selection.
• To exit press FAN or select “Exit” and press MODE
ADJUSTING THE REAL-TIME CLOCK
• Once the real-time clock menu has been selected use the UP or DOWN buttons to set each variable. MODE will save value
and proceed to next variable. FAN will return to prior variable.
• By default, the thermostat will automatically adjust the clock for Daylight Savings. This can be disabled by changing the
Auto Daylight Savings (setting 16) option in the installer menu
ADJUSTING THE HEAT OR COOL TEMPERATURE PROGRAM
• NOTE: Each period ends at the start time of the next upcoming period.
• NOTE: If congured to use only 2 periods, only DAY and NIGHT will be used, and the MORN and EVEN periods will not be
used or visible. If you use 1 period and 7 day programming, then thermostat will reset to the desired set temperature at the
same time each day.
• Once either HEAT or COOL programming sections has been selected, choose which day[s] to schedule together (i.e. all
weekdays together, or each day separately). Use the UP or DOWN buttons to scroll through the blinking days and press the
MODE to select each day with a indicator dot. Press FAN to deselect any previously selected day. Once all desired days are
selected, move blinking selection to “SCHED” and press the MODE button to proceed.
• Adjust the start time of the rst period using UP or DOWN buttons and press the MODE button. Press the UP or DOWN but-
tons to set the desired temperature for the rst period. Press the MODE button to continue to the next period.
• Repeat until all periods have been set. Thermostat will return to day selection page.
• If all desired days have been scheduled select “EXIT” and press MODE. Otherwise use the UP and DOWN buttons to move
blinking selection to desired days and press MODE to select day[s] for scheduling.
ENTERING EMERGENCY HEAT MODE (HP UNITS ONLY)
• While in HEAT mode, press DOWN + MODE for 5 seconds. The thermostat will show HEAT with “E” to conrm Emergency
Heat mode. This will use only the W2 wire as the heating source and will not call for compressor heating.
• To return to normal heating mode, set thermostat to HEAT mode, press and hold BOTH the MODE and DOWN buttons for at
least 5 seconds until the screen changes. The “E” will disappear and only show “HEAT” to conrm regular Heat mode.