Service and Parts Manual (2016, 2017, 2015)
Table Of Contents
- INTRODUCTION
- Important Safety Information
- Personal Injury Or Death Hazards
- Operation of Equipment in During Construction
- Model Number Reference Guide
- Serial Number Reference Guide
- Product Features
- General Specifications
- 230V COOLING AND HEATING PERFORMANCE
- 265V COOLING AND HEATING PERFORMANCE
- Electric Heat Data
- Dimensions
- Electrical Data
- Function and Control
- Digital Control User Input Configuration
- Digital Control
- Refrigeration Sequence Of Operation
- Refrigerant System Diagram
- PTAC Installation Recommendations
- Wall Sleeve Installation Instructions (PDXWS)
- Alternate Wall Installations
- PXDR10 Drain Kit Installation
- External Drain
- PXGA Standard Grille
- Chassis Install Preparation
- Thermostat
- Final Inspection & Start-up Checklist
- Refrigerant Charging
- Undercharged Refrigerant Systems
- Overcharged Refrigerant Systems
- Restricted Refrigerant System
- Sealed System Method of Charging/ Repairs
- Electrical
- Hermetic Components Check
- Reversing Valve Description And Operation
- Testing The Reversing Valve Solenoid Coil
- Checking The Reversing Valve
- Touch Test Chart : To Service Reversing Valves
- Compressor Checks
- Compressor Replacement
- Compressor Replacement -Special Procedure in Case of Compressor Burnout
- Basic Troubleshooting
- Malfunction Analysis
- Troubleshootin Chart
- Heat Pump
- Remote Wall Thermostat Wiring Diagram
- Cool With Electric Heat
- Heat Pump With Electric Heat
- PZE
- PZH
- Reference Sheet of Celsius and Fahrenheit
- Resistance Table for Air Indoor Temperature Sensor
- Resistance Table for Frost Protection Indoor and Outdoor Temperature Sensors
33 PB
INSTALLATION
PXDR10 Drain Kit Installation
10
FRP011
DRAIN TUBE
SIDE VIEW
FRONT VIEW
WALL SLEEVE
OPTIONAL AREA
PREFERRED AREA-
NO FOAM INSULATION
IF THE DRAIN MUST BE
LOCATED IN THE OPTIONAL
AREA, THE FOAM INSULATION
MUST BE CUT AWAY AND
REMOVED TO ALLOW ACCESS
TO THE DRAIN.
NUT
MOUNTING
PLATE
GASKET
SCREW
3"
Figure 11
Drain Kit Location and Installation
PXDR10
QUANTITY DESCRIPTION
2
1
1
3
4
2
2
COVER PLATES
MOUNTING PLATE
DRAIN TUBE
MOUNTING PLATE GASKET
#10 X ½” SHEET METAL SCREWS
#10-24 X ½ ” MACH. SCREWS
#10-24 X ½" LOCKNUTS
3. Remove.the.backing.from.the.gasket.and.mount.it.on.the.
.side.
of.the.mounting.plate...(See.Figure.12,.Page.11)...Insert.the.drain.
tube.through.the.hole.in.the.gasket.and.mounting.plate.so.the.tube.
.will.be .against.the.wall.sleeve.
4. Position.the .assembly.beneath.the.dril led.holes.and.secure.it.with.
#10-24.x.½".machine.screws.and.lock.nuts.pr ovided...S eal.the.tops.
of.the.screws.with.silicone.caulking..
5. Use.½".I.D..copper.tube,.PVC.pipe,.or.vinyl.hose.(obtained.locally).
to.connect.the.internal.drain.tube.to.the.drain.system.in.the.building.
6. Referring.to.Figure.12,.Detail.A,.Page.11,.locate .and.assemble.the.
tw
o.cover.plates.and.gaskets.over.the.drai n. holes .at.the.rear.
of.the.wall.sleeve...Attach.them.with.the.#10.sheet.metal.sc rews.
provided...Make.certain.that.the.fou r.
.slots.at.the.rear.of.
the.wall.sleeve.are.not.blocked.(See.drawing.of.the.b a ck.of.th e.
sleeve.Figure.12,.Page.11).
7. If.a.deep.wall.extension.(PDXWSEXT).is.used,.after.installing.the.
.suppl ied. .caulk.as.required...Be.su re.to.caulk.around.
the.
.and.the.wall.sleeve.where.the.hole.was.drilled.for.the.
drain.t ube..
PXDR10 Drain Kit Installation
Instructions (optional for new
construction)
NOTE:. Determi ne.whether.drain.will.be.located.within.the.wall,.on.the.
indoor.side,.or.will.drain.to.the.ex terior.of.th e.building...Follow.
appropriate.instr uctions.below.depending.on.your.particular.
type.of.installation.
Internal Drain
NOTE:. If.i nstalling.an.internal.drain,.you.MUST.inst all.a.drain.kit.on.
the.wall.sleeve.before.th e.wall.sleeve.is.installed.
1. Refer. to. Figu re. 11. and. locate. the. drain . within. the. “Preferred”.
area.of.best.drainage...Maintain.at.least.a.½”.clear ance.from.the.
embossed.a rea.
2. Usin g.the.mounting.plate.wi th.the.½”.hole.as.a.template,.mark.
and. drill.two,. 3/16”. mounting. holes. and. a.½”. drain. hole. in. the.
sleeve.bottom.