Window Installation Instructions Room Air Conditioners AUTO AUTO CONTINUOUS °F °C AUTO SYSTEM FAN MODE SCHEDULE FAN SPEED Standard Chassis Models 115-Volt: SS08, SS10, SS12, SS14, SM15, 208-230-Volt: SS12, SM18,SM21 SL24, SL28, SL36 115-Volt: EQ08,YS10 208-230-Volt: ES12, ES16, YS12, EM18, YM18, EM24, EL24, EL36, YL24 93001014_00
Airflow Selection and Adjustment Figure 13 Air flow direction adjustment left or right side of the discharge opening. Each of the banks of louvers can be directed left, right, up or down in order to achieve the most optimum move it in the direction that you would like the air to be directed. Please louvers than the other. Fresh air and exhaust control Your air conditioner has the ability to bring fresh air into the room or exhaust stale air out of the room.
Installation Instructions The following instructions are for standard chassis model groups READ THIS FIRST! Electrical Requirements sizes listed in Table 3. Table 3 WARNING MODEL DESIGNATION CABINET SIZE (H x W x D) SMALL CHASSIS - SS, 15 15⁄16" x 25 15⁄16" x 29" (405 mm x ES, YS 660 mm x 737 mm) Electrical Shock Hazard Make sure your electrical receptacle has the same configuration as your air conditioner’s plug. If different, consult a Licensed Electrician. Do not use plug adapters.
INSTALLATION HARDWARE AND ACCESSORY DETAIL ITEM 2 ITEM 3 ITEM 1 ITEM 5 ITEM 6 ITEM 4 ITEM 7 ITEM 8 ITEM 11 ITEM 10 ITEM 12 ITEM 9 ITEM 13 ITEM 14 ITEMS NOT TO SCALE ITEM NO DESCRIPTION FRR009 QTY.
Standard Window Installation Figure 15 NOTE: Hardware and accessories used during installation are shown on page 18. Each part will be referred as Item No. STEP 1. Remove the chassis Entrygard retainer by removing the far right screw (See Figure 14), save this screw to reattach the chassis retainer after installation (Step 12). Also, remove and discard the two retainer screws and washers located at the rear of the unit (See Figure 14). CAUTION Use Handle Locations [both sides] STEP 2. STEP 3.
NOTE: CAUTION Remove Shipping Blocks Prior to operating the unit remove the foam shipping blocks. Adjust the support brackets to provide an inside-to-outside slope for excess condensation drainage (Refer to Standard Window Installation, Figures 19 through 23). Tighten all screws.
Figure 17 #8 x 3/8” LONG SCREW (ITEM 7) 2 REQUIRED CABINET TOP ANGLE (ITEM 5) TAB SIDE ANGLE (ITEM 6) 2 REQUIRED DETAIL B-2 TAB LOOP SILL PLATE TAB DETAIL B-1 FRR013 Figure 18 TOP ANGLE (ITEM 5) CENTER CABINET IN WINDOW SIDE TO SIDE PULL WINDOW SASH DOWN BEHIND TOP ANGLE DRILL (3) 5/32” DIA.
Figure 19 3/8” SLOPE DOWN #10-24 x 1” HEX HD. SCREW (ITEM 2) SUPPORT BRACKET (ITEM 1) #12 x 2” SCREW (ITEM 4) SPACER SHOULD BE USED BETWEEN WALL AND BRACKET WHEN INSTALLED ON ALUMINUM OR VINYL SIDING. SUPPORT BRACKET (ITEM 1) 10-24 x FLAT WELD NUT (ITEM 3) FRR015 Figure 20 3/8” SLOPE DOWN CONDENSER AIR OUTLET CONDENSER AIR INLETS #10-24 SCREW #10-24 FLAT WELD NUT #12 x 2” SHEET METAL SCREW (ITEM 4) SPACER SHOULD BE USED BETWEEN WALL AND BRACKET WHEN INSTALLED ON ALUMINUM OR VINYL SIDING.
Figure 21 3/8” SLOPE DOWN CONDENSER AIR INLETS #10-24 SCREW #10-24 FLAT WELD NUT STONE LEDGE SPACER #12 x 2” SHEET METAL SCREW (ITEM 4) FRR017 Figure 22 3/8” SLOPE DOWN #10-24 SCREW STRAIGHTEN TAB TO LAY FLAT ALONG THE BOTTOM RAIL OF THE SHELL #10-24 FLAT WELD NUT SECURE THE LONGEST SIDE OF THE BRACKET TO THE SHELL ADJUST IN OR OUT TO REST ON THE LEDGE STONE LEDGE FRR018 24
Figure 23 3/8” SLOPE DOWN #10-24 SCREW DIMENSION “A” CUT HERE CUT TO FIT DIMENSION “A” AND BEND DOWN TO FORM A VERTICAL LEG. #10-24 FLAT WELD NUT STONE LEDGE A OUTSIDE WALL DISCARD SHADED AREA FRR019 Figure 24 MEASURE DISTANCE “B” TO INSIDE OF THE CHANNEL ON EACH SIDE. CUT HERE AND DISCARD CENTER WASTE MATERIAL. B B WINGBOARD B B SUBTRACT 1/8” FROM DIMENSION “B” AND MEASURE FROM THE EDGE OF THE WINGBOARD (ITEM 8), MARK, SCORE AND CUT WITH APPROPRIATE CUTTING TOOL.
Figure 25 SPRING STEEL CLIP (ITEM 10) 2 REQUIRED “J” TYPE SPEED NUT (ITEM #9) 2 REQUIRED 3" CUT WINGBOARD PANEL CUT EDGE ROTATED 90° 3" SLIDE CLIP OVER CUT EDGE OF WINGBOARD PANEL CENTER THE HOLE IN THE SPEED NUT OVER THE SLOT IN THE WINGBOARD PANEL FRR021 2
STEP 10. INSTALL THE R1 INSULATION PANEL – To minimize air leaks and ensure optimal insulation, install the included R1 insulation panel. (14 in parts list) (See Figure below A-C). STEP 11. Pull the window sash down behind the gasket. Measure and cut the dark foam window seal gasket (Item 13) and install it between the upper glass panel and the top part of the lower window sash (Figure 29).
Figure 26 Figure 27 TOP OF CABINET INSERT VINYL WINDOW SEAL GASKET OVER TOP ANGLE TO WINGBOARD (ITEM 12) PLACE WINGBOARD PANEL IN WINDOW JAM TO COMPRESS THE SPRINGS INSIDE THE RUNNERS, AND SWING THE WINGBOARD PANELS INTO PLACE AS INDICATED BY THE DASHED LINES.
OPTIONAL: The factory assembles the supply cord so that it exits the left side of the unit at the bottom. At the consumer’s discretion, the supply cord can be routed to exit the right side of the unit. To do this, route the supply cord to the right side. Pull the supply cord taunt through the loops (Refer to Cord Routing Change, Figure 30) and route the cord down. STEP 14. Use Tool Provided Please use the provided tool to attach the decorative front to the chassis.
Cord Routing Change STEP 17. Unplug unit. Carefully pull out electrical control panel 1", but not all the way. Figure 32 WARNING 1 INCH Electrical Shock Hazard Make sure your electrical receptacle has the same configuration as your air conditioner’s plug. If different, consult a Licensed Electrician. Do not use plug adapters. Do not use an extension cord. Do not remove ground prong. Always plug into a grounded 3 prong oulet.
STEP 20. Carefully push electrical control panel back into chassis. Figure 35 STEP 22. If running power cord to the right of the unit install the cord into the cord retainer clips along the bottom front of the unit. Figure 37 ELECTRICAL CONTROL PANEL CORD RETAINER CLIPS FRR059 STEP 21. Reinstall the 3 screws removed earlier to secure electrical control panel.
THIS PAGE INTENTIONALLY LEFT BLANK 29
Friedrich Air Conditioning Co. Post Office Box 1540 • San Antonio, Texas 78295-1540 4200 N. Pan Am Expressway • San Antonio, Texas 78218-5212 (210) 357-4400 • FAX (210) 357-4480 www.friedrich.